Add fanout mode PACKET_FANOUT_CBPF that accepts a classic BPF program
to select a socket.

This avoids having to keep adding special case fanout modes. One
example use case is application layer load balancing. The QUIC
protocol, for instance, encodes a connection ID in UDP payload.

Also add socket option SOL_PACKET/PACKET_FANOUT_DATA that updates data
associated with the socket group. Fanout mode PACKET_FANOUT_CBPF is the
only user so far.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We already have IFLA_IPTUN_ netlink attributes. The IP_TUN_ attributes look
very similar, yet they serve very different purpose. This is confusing for
anyone trying to implement a user space tool supporting lwt.

As the IP_TUN_ attributes are used only for the lightweight tunnels, prefix
them with LWTUNNEL_IP_ instead to make their purpose clear. Also, it's more
logical to have them in lwtunnel.h together with the encap enum.

Fixes: 3093fbe7 ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0b50dc4f ("Convert smsc911x to use ACPI as well as DT") makes
the call to smsc911x_probe_config() unconditional, and no longer fails if
there is no device node. device_get_phy_mode() is called unconditionally,
and if there is no phy node configured returns an error code. This error
code is assigned to phy_interface, and interpreted elsewhere in the code
as valid phy mode. This in turn causes qemu to crash when running a
variant of realview_pb_defconfig.

	qemu: hardware error: lan9118_read: Bad reg 0x86

Fixes: 0b50dc4f ("Convert smsc911x to use ACPI as well as DT")
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2015-08-17

1) Fix IPv6 ECN decapsulation for IPsec interfamily tunnels.
   From Thomas Egerer.

2) Use kmemdup instead of duplicating it in xfrm_dump_sa().
   From Andrzej Hajda.

3) Pass oif to the xfrm lookups so that it gets set on the flow
   and the resolver routines can match based on oif.
   From David Ahern.

4) Add documentation for the new xfrm garbage collector threshold.
   From Alexander Duyck.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparse builds have been warning for a really long time now
that etherdevice.h has a conversion that is unsafe.

  include/linux/etherdevice.h:79:32: warning: restricted __be16 degrades to integer

This code change fixes the issue and generates the exact
same assembly before/after (checked on x86_64)

Fixes: 2c722fe1 (etherdevice: Optimize a few is_<foo>_ether_addr functions)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phil Sutter says:

====================
net: introduce IFF_NO_QUEUE as successor of zero tx_queue_len

This series adds a new private net_device flag indicating that a device may
(and probably should) be used without a queueing discipline attached to it.
This is already common practice for many virtual device types like e.g.
loopback, VLAN (802.1Q) or bridges (802.1D). The reason for this is that these
devices lack an underlying layer which could impose back pressure and therefore
making a TX queue necessary to not slow down senders.

Up to now, drivers being aware of the above applying to them set
dev->tx_queue_len to zero to indicate no qdisc should be attached to the
interface they drive and the kernel reacts upon this by assigning the noop
qdisc instead of the default pfifo_fast. This implicit agreement though leads
to an inconvenient situation once a user tries to attach a real qdisc to these
devices, as the formerly special tx_queue_len value becomes a regular one,
limiting the queue to zero packets and thus prevents any TX from happening. To
overcome this, practically all qdisc implementations intercept and sanitize the
malicious value.

With this series applied, drivers may signal the lack of need for a qdisc
without having to tamper with tx_queue_len, making fallbacks in qdiscs and
caveats in userspace unnecessary.

Upon upstream acceptance, this series will be followed up by a set of patches
converting device drivers, adding a warning so out-of-tree driver authors get
aware of this change and dropping all special handling of tx_queue_len in
net/sched/.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Handle IFF_NO_QUEUE as alternative to tx_queue_len being zero.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This private net_device flag can be set by drivers to inform that a
device runs fine without a qdisc attached. This was formerly done by
setting tx_queue_len to zero.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A zero length payload means that no TLV (Type Length Value) data has
been passed. Prior to this patch a non-existing TLV could be sanity
checked with TLV_OK() resulting in random behavior where a user
sending an empty message occasionally got a incorrect "operation not
supported" message back.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Management firmware tells driver in case bandwidth configuration for
a specific function exists, but [regretably] the same field has different
meanings depending on the multi-function mode - it can either be
a percentile value or an actual speed.

For newer multi-function modes current logic is incorrect -
driver understands values as actual speeds instead of percentages,
causing the resulting chip configuration to be incorrect.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fib_lookup() forces FIB_LOOKUP_NOREF flag, while fib_table_lookup()
does not.

This patch solves the typical message at reboot time or device
dismantle :

unregister_netdevice: waiting for eth0 to become free. Usage count = 4

Fixes: 3bfd8472 ("net: Use passed in table for nexthop lookups")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsa@cumulusnetworks.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
VRF-lite - v6

In the context of internet scale routing a requirement that always comes
up is the need to partition the available routing tables into disjoint
routing planes. A specific use case is the multi-tenancy problem where
each tenant has their own unique routing tables and in the very least
need different default gateways.

This patch allows the ability to create virtual router domains (aka VRFs
(VRF-lite to be specific) in the linux packet forwarding stack. The main
observation is that through the use of rules and socket binding to interfaces,
all the facilities that we need are already present in the infrastructure. What
is missing is a handle that identifies a routing domain and can be used to
gather applicable rules/tables and uniqify neighbor selection. The scheme used
needs to preserves the notions of ECMP, and general routing principles.

This driver is a cross between functionality that the IPVLAN driver
and the Team drivers provide where a device is created and packets
into/out of the routing domain are shuttled through this device. The
device is then used as a handle to identify the applicable rules. The
VRF device is thus the layer3 equivalent of a vlan device.

The very important point to note is that this is only a Layer3 concept
so L2 tools (e.g., LLDP) do not need to be run in each VRF, processes can
run in unaware mode or select a VRF to be talking through. Also the
behavioral model is a generalized application of the familiar VRF-Lite
model with some performance paths that need optimization. (Specifically
the output route selector that Roopa, Robert, Thomas and EricB are
currently discussing on the MPLS thread)

High Level points
=================
1. Simple overlay driver (minimal changes to current stack)
   * uses the existing fib tables and fib rules infrastructure
2. Modelled closely after the ipvlan driver
3. Uses current API and infrastructure.
   * Applications can use SO_BINDTODEVICE or cmsg device indentifiers
     to pick VRF (ping, traceroute just work)
   * Standard IP Rules work, and since they are aggregated against the
     device, scale is manageable
4. Completely orthogonal to Namespaces and only provides separation in
   the routing plane (and ARP)

                                                 N2
           N1 (all configs here)          +---------------+
    +--------------+                      |               |
    |swp1 :10.0.1.1+----------------------+swp1 :10.0.1.2 |
    |              |                      |               |
    |swp2 :10.0.2.1+----------------------+swp2 :10.0.2.2 |
    |              |                      +---------------+
    | VRF 1        |
    | table 5      |
    |              |
    +---------------+
    |              |
    | VRF 2        |                             N3
    | table 6      |                      +---------------+
    |              |                      |               |
    |swp3 :10.0.2.1+----------------------+swp1 :10.0.2.2 |
    |              |                      |               |
    |swp4 :10.0.3.1+----------------------+swp2 :10.0.3.2 |
    +--------------+                      +---------------+

Given the topology above, the setup needed to get the basic VRF
functions working would be

Create the VRF devices and associate with a table
    ip link add vrf1 type vrf table 5
    ip link add vrf2 type vrf table 6

Install the lookup rules that map table to VRF domain
    ip rule add pref 200 oif vrf1 lookup 5
    ip rule add pref 200 iif vrf1 lookup 5
    ip rule add pref 200 oif vrf2 lookup 6
    ip rule add pref 200 iif vrf2 lookup 6

    ip link set vrf1 up
    ip link set vrf2 up

Enslave the routing member interfaces
    ip link set swp1 master vrf1
    ip link set swp2 master vrf1
    ip link set swp3 master vrf2
    ip link set swp4 master vrf2

Connected and local routes are automatically moved from main and local
tables to the VRF table.

ping using VRF0 is simply
    ping -I vrf0 10.0.1.2

Design Highlights
=================
If a device is enslaved to a VRF device (ie., associated with a VRF)
then:
1. Rx path
   The master device index is used as the iif for all lookups.

2. Tx path
   Similarly, for Tx the VRF device oif is used in the flow to direct
   lookups to the table associated with the VRF via its rule. From there
   the FLOWI_FLAG_VRFSRC flag is used to indicate that the oif should
   not be used for FIB table lookups.

3. Connected and local routes
   On link up for a device, connected and local routes are added to the
   table associated with the VRF device, rather than the local and main
   tables.

4. Socket lookups
   Sockets operating in the VRF must be bound to the VRF device. As such
   socket lookups compare the VRF device index to sk_bound_dev_if.

5. Neighbor entries
   Neighbor entries are not impacted by the VRF device. Entries are
   associated with a particular interface; the VRF association is indirect
   via the interface-to-VRF device enslavement.

Version 6
- addressed comments from DaveM

- added patch to properly set oif in ip_send_unicast_reply. Needs to be
  set to VRF device for proper FIB lookup

- added patch to handle IP fragments

Version 5
- dropped patch regarding socket lookups; no longer needed
  + removed vrf helpers no longer needed after this patch is dropped
- removed dev_open and close operations
  + no need to reset vrf data on an ifdown and creates problems if a
    slave is deleted while the vrf interface is down (Thanks, Nikolay)
- cleanups for sparse warnings
  + make C=2 is now clean for vrf driver

Version 4
- builds are clean with and without VRF device enabled (no, yes and module)
- tightened the driver implementation
  + device add/delete, slave add/remove, and module unload are all clean
- fixed RCU references
  + with RCU and lock debugging enabled changes are clean through the
    suite of tests
- TX path uses custom dst, so patch refactoring rtable allocation is
  dropped along with the patch adding rt_nexthop helper
- dropped the task patch that adds default bind to interface for sockets
  and the associated chvrf example command
  + the patches are a convenience for running unmodified code. They
    are not needed for the core functionality. Any application with
    support for SO_BINDTODEVICE works properly with this patch set.

Version 3
- addressed comments from first 2 RFCs with the exception of the name
  Nicolas: We will do the name conversion once we agree on what the
           correct name should be (vrf, mrf or something else)

-  packets flow through the VRF device in both directions allowing the
   following:
   - tcpdump -i vrf<n>
   - tc rules on vrf device
   - netfilter rules on vrf device

TO-DO
=====
1. IPv6

2. ipsec, xfrms
   - dst patch accepted into ipsec-next; will post VRF patch once merge happens

3. listen filter to allow 1 socket to work with multiple VRF devices
   - i.e., bind to VRF's a, b, c only or NOT VRFs e, f, g

Eric B:
  I have ipsec working with VRFs implemented using the VRF driver,
  including the worst case scenario of complete duplication in the
  networking config.

Thanks to Nikolay for his many, many code reviews whipping the device
driver into shape, and bug-Fixes and ideas from Hannes, Roopa Prabhu,
Jon Toppins, Jamal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver borrows heavily from IPvlan and teaming drivers.

Routing domains (VRF-lite) are created by instantiating a VRF master
device with an associated table and enslaving all routed interfaces that
participate in the domain. As part of the enslavement, all connected
routes for the enslaved devices are moved to the table associated with
the VRF device. Outgoing sockets must bind to the VRF device to function.

Standard FIB rules bind the VRF device to tables and regular fib rule
processing is followed. Routed traffic through the box, is forwarded by
using the VRF device as the IIF and following the IIF rule to a table
that is mated with the VRF.

Example:

   Create vrf 1:
     ip link add vrf1 type vrf table 5
     ip rule add iif vrf1 table 5
     ip rule add oif vrf1 table 5
     ip route add table 5 prohibit default
     ip link set vrf1 up

   Add interface to vrf 1:
     ip link set eth1 master vrf1
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fragmentation cache uses information from the IP header to reassemble
packets. That information can be duplicated across VRFs -- same source
and destination addresses, protocol and id. Handle fragmentation with
VRFs by adding the VRF device index to entries in the cache and the
lookup arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If output device is not specified use VRF device if input device is
enslaved. This is needed to ensure tcp acks and resets go out VRF device.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a user passes in a table for new routes use that table for nexthop
lookups. Specifically, this solves the case where a connected route does
not exist in the main table, but only another table and then a subsequent
route is added with a next hop using the connected route. ie.,

$ ip route ls
default via 10.0.2.2 dev eth0
10.0.2.0/24 dev eth0  proto kernel  scope link  src 10.0.2.15
169.254.0.0/16 dev eth0  scope link  metric 1003
192.168.56.0/24 dev eth1  proto kernel  scope link  src 192.168.56.51

$ ip route ls table 10
1.1.1.0/24 dev eth2  scope link

Without this patch adding a nexthop route fails:

$ ip route add table 10 2.2.2.0/24 via 1.1.1.10
RTNETLINK answers: Network is unreachable

With this patch the route is added successfully.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a device associated with a VRF is brought up or down routes
should be added to/removed from the table associated with the VRF.
fib_magic defaults to using the main or local tables. Have it use
the table with the device if there is one.

A part of this is directing prefsrc validations to the correct
table as well.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently inet_addr_type and inet_dev_addr_type expect local addresses
to be in the local table. With the VRF device local routes for devices
associated with a VRF will be in the table associated with the VRF.
Provide an alternate inet_addr lookup to use a specific table rather
than defaulting to the local table.

inet_addr_type_dev_table keeps the same semantics as inet_addr_type but
if the passed in device is enslaved to a VRF then the table for that VRF
is used for the lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently inet_addr_type and inet_dev_addr_type expect local addresses
to be in the local table. With the VRF device local routes for devices
associated with a VRF will be in the table associated with the VRF.
Provide an alternate inet_addr lookup to use a specific table rather
than defaulting to the local table.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For unconnected UDP sockets using a VRF device lookup source address
based on VRF table. This allows the UDP header to be properly setup
before showing up at the VRF device via the dst.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As with ingress use the index of VRF master device for route lookups on
egress. However, the oif should only be used to direct the lookups to a
specific table. Routes in the table are not based on the VRF device but
rather interfaces that are part of the VRF so do not consider the oif for
lookups within the table. The FLOWI_FLAG_VRFSRC is used to control this
latter part.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On ingress use index of VRF master device for route lookups if real device
is enslaved. Rules are expected to be installed for the VRF device to
direct lookups to a specific table.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a VRF_MASTER flag for interfaces and helper functions for determining
if a device is a VRF_MASTER.

Add link attribute for passing VRF_TABLE id.

Add vrf_ptr to netdevice.

Add various macros for determining if a device is a VRF device, the index
of the master VRF device and table associated with VRF device.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is useful information to include in ipv6 netlink messages that
report interface information.  IFLA_OPERSTATE is already included in
ipv4 messages, but missing for ipv6.  This closes that gap.
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 10e4ea75 ("net: Fix race condition in store_rps_map") has moved the
manipulation of the rps_needed jump label under a spinlock. Since changing
the state of a jump label may sleep this is incorrect and causes warnings
during runtime.

Make rps_map_lock a mutex to allow sleeping under it.

Fixes: 10e4ea75 ("net: Fix race condition in store_rps_map")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: mv88e6xxx: add hardware VLAN support

This patchset brings support to access hardware VLAN entries in DSA and
mv88e6xxx, through switchdev VLAN objects.

In the following example, ports swp[0-2] belong to bridge br0, and ports
swp[3-4] belong to bridge br1. Here's an example of what can be achieved
after this patchset:

    # bridge vlan add dev swp1 vid 100 master
    # bridge vlan add dev swp2 vid 100 master
    # bridge vlan add dev swp3 vid 100 master
    # bridge vlan add dev swp4 vid 100 master
    # bridge vlan del dev swp1 vid 100 master

The above commands correctly programmed hardware VLAN 100 for port swp2,
while ports swp3 and swp4 use software VLAN 100, as shown with:

    # bridge vlan
    port	vlan ids
    swp0	None
    swp0
    swp1	None
    swp1
    swp2	 100

    swp2	 100

    swp3	 100

    swp3
    swp4	 100

    swp4
    br0	None
    br1	None

Assuming that port 5 is the CPU port, the hardware VLAN table would
contain the following data:

    VID  FID  SID  0  1  2  3  4  5  6
    100    8    0  x  x  t  x  x  t  x

Where 'x' means excluded, and 't' means tagged.

Also, adding an FDB entry to VLAN 100 for port swp2 like this:

    # bridge fdb add 3c:97:0e:11:6e:30 dev swp2 vlan 100

Would result in the following example output:

    # bridge fdb
    # 01:00:5e:00:00:01 dev eth0 self permanent
    # 01:00:5e:00:00:01 dev eth1 self permanent
    # 00:50:d2:10:78:15 dev swp0 master br0 permanent
    # 00:50:d2:10:78:15 dev swp2 vlan 100 master br0 permanent
    # 3c:97:0e:11:6e:30 dev swp2 vlan 100 self static
    # 00:50:d2:10:78:15 dev swp3 master br1 permanent
    # 00:50:d2:10:78:15 dev swp3 vlan 100 master br1 permanent

And the Address Translation Unit would contain:

    DB   T/P  Vec State Addr
    008  Port 004   e   3c:97:0e:11:6e:30
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit changes the 802.1Q mode of each port from Disabled to
Secure. This enables the VLAN support, by checking the VTU entries on
ingress.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement port_pvid_set and port_vlan_add to add new entries in the VLAN
hardware table, and join ports to them.

The patch also implement the STU Get Next and Load Purge operations,
since it is required to have a valid STU entry for at least all VLANs.

Each VLAN has its own forwarding database, with FID num_ports+1 to 4095.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the VTU Load Purge operation and implement the
port_vlan_del driver function to remove a port from a VLAN entry, and
delete the VLAN if the given port was its last member.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add an helper function to read the next valid VLAN entry for a given
port. It is used in the VID to FID conversion function to retrieve the
forwarding database assigned to a given VLAN port.

Finally update the FDB getnext operation to iterate on the next valid
port VLAN when the end of the current database is reached.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the port_pvid_get and vlan_getnext driver functions required
to dump VLAN entries from the hardware, with the VTU Get Next operation.

Some functions and structure will be shared with STU operations, since
their table format are similar (e.g. STU data entries are accessible
with the same registers as VTU entries, except with an offset of 2).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the VTU Flush operation (which also flushes the STU), so that
warm boots won't preserved old entries.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new functions in DSA drivers to access hardware VLAN entries through
SWITCHDEV_OBJ_PORT_VLAN objects:

 - port_pvid_get() and vlan_getnext() to dump a VLAN
 - port_vlan_del() to exclude a port from a VLAN
 - port_pvid_set() and port_vlan_add() to join a port to a VLAN

The DSA infrastructure will ensure that each VLAN of the given range
does not already belong to another bridge. If it does, it will fallback
to software VLAN and won't program the hardware.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like the ipv4 patch with a similar title, this adds a sysctl to allow
the user to change routing behavior based on whether or not the
interface associated with the nexthop was an up or down link.  The
default setting preserves the current behavior, but anyone that enables
it will notice that nexthops on down interfaces will no longer be
selected:

net.ipv6.conf.all.ignore_routes_with_linkdown = 0
net.ipv6.conf.default.ignore_routes_with_linkdown = 0
net.ipv6.conf.lo.ignore_routes_with_linkdown = 0
...

When the above sysctls are set, not only will link status be reported to
userspace, but an indication that a nexthop is dead and will not be used
is also reported.

1000::/8 via 7000::2 dev p7p1  metric 1024 dead linkdown  pref medium
1000::/8 via 8000::2 dev p8p1  metric 1024  pref medium
7000::/8 dev p7p1  proto kernel  metric 256 dead linkdown  pref medium
8000::/8 dev p8p1  proto kernel  metric 256  pref medium
9000::/8 via 8000::2 dev p8p1  metric 2048  pref medium
9000::/8 via 7000::2 dev p7p1  metric 1024 dead linkdown  pref medium
fe80::/64 dev p7p1  proto kernel  metric 256 dead linkdown  pref medium
fe80::/64 dev p8p1  proto kernel  metric 256  pref medium

This also adds devconf support and notification when sysctl values
change.

v2: drop use of rt6i_nhflags since it is not needed right now
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to track current link status of ipv6 nexthops to match
recent changes that added support for ipv4 nexthops.  This takes a
simple approach to track linkdown status for next-hops and simply
checks the dev for the dst entry and sets proper flags that to be used
in the netlink message.

v2: drop use of rt6i_nhflags since it is not needed right now
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Handle TRACE_PKT, stack can sniff them on the first port
Add debubfs enrty to configure tracing for offload traffic like iWARP
& iSCSI for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HWM_REVERSE() macro is unused, remove it.
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rocker driver tracks arp_tbl neighs to resolve IPv4 route nexthops.  The
driver uses NETEVENT_NEIGH_UPDATE for neigh adds and updates, but there is
no event when the neigh is removed from the device (such as when the device
goes admin down).  This patches hooks ndo_neigh_destroy so the driver can
know when a neigh is removed from the device.  In response, the driver will
purge the neigh entry from its internal tbl.

I didn't find an in-tree users of ndo_neigh_destroy, so I'm not sure if
this ndo is vestigial or if there are out-of-tree users.  In any case, it
does what I need here.  An alternative design would be to generate
NETEVENT_NEIGH_UPDATE event when neigh is being destroyed, setting state to
NUD_NONE so driver knows neigh entry is dead.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On sucessful probe, driver prints the switch ID.  This patch changes the
format of the printed ID to match what's used in sysfs phys_switch_id node.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeremy Linton says:

====================
Enable smsc911x for use with ACPI

This set of patches enables the front Ethernet port on the
ARM Juno development platform when used with an ACPI enabled kernel.

These patches covert the of_property* calls in the driver to the
DT/ACPI agnostic device_property* calls, and add the arm hardware
id to the acpi_match_table.

To support the above changes I copied a couple routines from
of_net into the properties.c file, and modified them to
be ACPI/DT agnostic. I'm not 100% sure this is the correct location
for these functions. But I think they are required to avoid having
a dozen different implementations scattered across assorted Ethernet
adapters that are being enabled to use ACPI properties.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>