According to the NanoPi-A64 schematics, DCDC1 is connected to a voltage
rail named "VDD_SYS_3.3V". All users seem to expect 3.3V here: the
Ethernet PHY, the uSD card slot, the camera interface and the GPIO pins
on the headers.
Fix up the voltage on the regulator to lift it up to 3.3V.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Olinuxino has two USB sockets:
USB0 is connected to a micro B socket. As it has the ID pin wired and
the VBUS line connected to the PMIC, we describe it as a proper OTG socket,
which switches between host and device automatically.
USB1 is connected to a normal USB A socket. PG9 enables the power line,
so add the required regulator as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

Add the DT nodes required to enable the Gigabit Ethernet on the board.
The PHY is powered by the always-on power rail VDD_SYS_3.3V (DCDC1).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Olinuxino board uses DDR3L chips which are supposed to be driven
with 1.35V. The reset default of the AXP is properly set to 1.36V.

While technically the chips can also run at 1.5 volts, changing the
voltage on the fly while booting Linux is asking for trouble. Also
running at a lower voltage saves power.

So fix the DCDC5 value to match the actual board design.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Martin Lucina <martin@lucina.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Orange Pi Win board uses the AXP's ALDO1 power rail to drive the
VCC-CSI line, which, according to the schematic, needs to be set to 2.8V.

Also the ELDO3 power rail is connected to the CSI, with somewhat unclear
voltage requirements. Add this regulator and allow the voltage to be set
between 1.5V and 1.8V, which are the voltages mentioned in the
schematic.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Orange Pi Win comes with 2 MB SPI flash, add the node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Orange Pi Win features a soldered WiFi chip on the board, connected
via the SDIO interface. Add the required DT nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Orange Pi Win has a green status LED, add the DT node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Orange Pi Win exposes several UARTs on header pins, and connects one
to the on-board WiFi/Bluetooth chip.

Add the pinmux definitions to the UART nodes, but keep them disabled.
Enable the UART1, which is wired to the Bluetooth chip, and add a serdev
node. There is no binding for the BT8723 yet, so leave this mostly empty
for now.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Orange Pi Win has the usual Gigabit PHY connected to the EMAC.
Its power is controlled by GPIO PD14.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Orange Pi Win has a micro USB-B socket, connected to the SoC's
USB-OTG port. Its power is supplied by the AXP PMIC, and the ID pin is
connected to GPIO PH9. It can serve both as a host or a client port.

Add the respective DT nodes to enable it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: enable paired EHCI/OHCI device nodes and regulator supply]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Orange Pi Win has four standard USB-A sockets, connected to an
on-board USB hub. The hub's and socket's power regulators are enabled by
GPIO PD7.

Add the regulator to the DT to enable the power supply.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Orange Pi Win has a microSD card slot which is connected via all
four SD data lines. As the DT was not mentioning this fact, we got the
default single bit transfers, losing out on performance.
Also, as microSD does not have a write protect switch, we disable this
feature in the DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

The Pine64-LTS is a variant of the Pine64 board, from the software
visible side resembling a SoPine module on a baseboard, though the
board has the SoC and DRAM integrated on one PCB.
Due to this it basically shares the DT with the SoPine baseboard, which
we mimic in our DT by inclucing the boardboard .dts into the new file,
just overwriting the model name.
Having a separate .dts for this seems useful, since we don't know yet if
there are subtle differences between the two. Also the SoC on the LTS
board is technically an "R18" instead of the original "A64", although as
far as we know this is just a relabelled version of the original SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

Current kernels complain when booting on an A64 Soc:
....
[    1.904297] cacheinfo: Unable to detect cache hierarchy for CPU 0
....
Not a real biggie on this flat topology, but also easy enough to fix.

Add the L2 cache node and let each CPU point to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>

Another user of cd-inverted seems to have crept in. Switch it away from
cd-inverted to be consistent with other sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

The A64 have a SID controller which consist of EFUSE (starting at 0x200)
and three registers to read/write some of the protected efuses.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Pull timer update from Thomas Gleixner:
 "New defines for the compat time* types so they can be shared between
  32bit and 64bit builds. Not used yet, but merging them now allows the
  actual conversions to be merged through different maintainer trees
  without dependencies

  We still have compat interfaces for 32bit on 64bit even with the new
  2038 safe timespec/val variants because pointer size is different. And
  for the old style timespec/val interfaces we need yet another 'compat'
  interface for both 32bit native and 32bit on 64bit"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  y2038: Provide aliases for compat helpers

Pull IDA updates from Matthew Wilcox:
 "A better IDA API:

      id = ida_alloc(ida, GFP_xxx);
      ida_free(ida, id);

  rather than the cumbersome ida_simple_get(), ida_simple_remove().

  The new IDA API is similar to ida_simple_get() but better named.  The
  internal restructuring of the IDA code removes the bitmap
  preallocation nonsense.

  I hope the net -200 lines of code is convincing"

* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
  ida: Change ida_get_new_above to return the id
  ida: Remove old API
  test_ida: check_ida_destroy and check_ida_alloc
  test_ida: Convert check_ida_conv to new API
  test_ida: Move ida_check_max
  test_ida: Move ida_check_leaf
  idr-test: Convert ida_check_nomem to new API
  ida: Start new test_ida module
  target/iscsi: Allocate session IDs from an IDA
  iscsi target: fix session creation failure handling
  drm/vmwgfx: Convert to new IDA API
  dmaengine: Convert to new IDA API
  ppc: Convert vas ID allocation to new IDA API
  media: Convert entity ID allocation to new IDA API
  ppc: Convert mmu context allocation to new IDA API
  Convert net_namespace to new IDA API
  cb710: Convert to new IDA API
  rsxx: Convert to new IDA API
  osd: Convert to new IDA API
  sd: Convert to new IDA API
  ...

Pull gcc plugin fix from Kees Cook:
 "Lift gcc test into Kconfig. This is for better behavior when the
  kernel is built with Clang, reported by Stefan Agner"

* tag 'gcc-plugins-v4.19-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  gcc-plugins: Disable when building under Clang

Pull perf updates from Thomas Gleixner:
 "Kernel:
   - Improve kallsyms coverage
   - Add x86 entry trampolines to kcore
   - Fix ARM SPE handling
   - Correct PPC event post processing

  Tools:
   - Make the build system more robust
   - Small fixes and enhancements all over the place
   - Update kernel ABI header copies
   - Preparatory work for converting libtraceevnt to a shared library
   - License cleanups"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits)
  tools arch: Update arch/x86/lib/memcpy_64.S copy used in 'perf bench mem memcpy'
  tools arch x86: Update tools's copy of cpufeatures.h
  perf python: Fix pyrf_evlist__read_on_cpu() interface
  perf mmap: Store real cpu number in 'struct perf_mmap'
  perf tools: Remove ext from struct kmod_path
  perf tools: Add gzip_is_compressed function
  perf tools: Add lzma_is_compressed function
  perf tools: Add is_compressed callback to compressions array
  perf tools: Move the temp file processing into decompress_kmodule
  perf tools: Use compression id in decompress_kmodule()
  perf tools: Store compression id into struct dso
  perf tools: Add compression id into 'struct kmod_path'
  perf tools: Make is_supported_compression() static
  perf tools: Make decompress_to_file() function static
  perf tools: Get rid of dso__needs_decompress() call in __open_dso()
  perf tools: Get rid of dso__needs_decompress() call in symbol__disassemble()
  perf tools: Get rid of dso__needs_decompress() call in read_object_code()
  tools lib traceevent: Change to SPDX License format
  perf llvm: Allow passing options to llc in addition to clang
  perf parser: Improve error message for PMU address filters
  ...

Pull x86 fixes from Thomas Gleixner:

 - Correct the L1TF fallout on 32bit and the off by one in the 'too much
   RAM for protection' calculation.

 - Add a helpful kernel message for the 'too much RAM' case

 - Unbreak the VDSO in case that the compiler desides to use indirect
   jumps/calls and emits retpolines which cannot be resolved because the
   kernel uses its own thunks, which does not work for the VDSO. Make it
   use the builtin thunks.

 - Re-export start_thread() which was unexported when the 32/64bit
   implementation was unified. start_thread() is required by modular
   binfmt handlers.

 - Trivial cleanups

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/speculation/l1tf: Suggest what to do on systems with too much RAM
  x86/speculation/l1tf: Fix off-by-one error when warning that system has too much RAM
  x86/kvm/vmx: Remove duplicate l1d flush definitions
  x86/speculation/l1tf: Fix overflow in l1tf_pfn_limit() on 32bit
  x86/process: Re-export start_thread()
  x86/mce: Add notifier_block forward declaration
  x86/vdso: Fix vDSO build if a retpoline is emitted

Pull irq update from Thomas Gleixner:
 "A small set of updats/fixes for the irq subsystem:

   - Allow GICv3 interrupts to be configured as wake-up sources to
     enable wakeup from suspend

   - Make the error handling of the STM32 irqchip init function work

   - A set of small cleanups and improvements"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3: Allow interrupt to be configured as wake-up sources
  irqchip/tango: Set irq handler and data in one go
  dt-bindings: irqchip: renesas-irqc: Document r8a774a1 support
  irqchip/s3c24xx: Remove unneeded comparison of unsigned long to 0
  irqchip/stm32: Fix init error handling
  irqchip/bcm7038-l1: Hide cpu offline callback when building for !SMP

Pull licking update from Thomas Gleixner:
 "Mark the switch cases which fall through to the next case with the
  proper comment so the fallthrough compiler checks can be enabled"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex: Mark expected switch fall-throughs

Merge tag 'libnvdimm-for-4.19_dax-memory-failure' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm

Pull libnvdimm memory-failure update from Dave Jiang:
 "As it stands, memory_failure() gets thoroughly confused by dev_pagemap
  backed mappings. The recovery code has specific enabling for several
  possible page states and needs new enabling to handle poison in dax
  mappings.

  In order to support reliable reverse mapping of user space addresses:

   1/ Add new locking in the memory_failure() rmap path to prevent races
      that would typically be handled by the page lock.

   2/ Since dev_pagemap pages are hidden from the page allocator and the
      "compound page" accounting machinery, add a mechanism to determine
      the size of the mapping that encompasses a given poisoned pfn.

   3/ Given pmem errors can be repaired, change the speculatively
      accessed poison protection, mce_unmap_kpfn(), to be reversible and
      otherwise allow ongoing access from the kernel.

  A side effect of this enabling is that MADV_HWPOISON becomes usable
  for dax mappings, however the primary motivation is to allow the
  system to survive userspace consumption of hardware-poison via dax.
  Specifically the current behavior is:

     mce: Uncorrected hardware memory error in user-access at af34214200
     {1}[Hardware Error]: It has been corrected by h/w and requires no further action
     mce: [Hardware Error]: Machine check events logged
     {1}[Hardware Error]: event severity: corrected
     Memory failure: 0xaf34214: reserved kernel page still referenced by 1 users
     [..]
     Memory failure: 0xaf34214: recovery action for reserved kernel page: Failed
     mce: Memory error not recovered
     <reboot>

  ...and with these changes:

     Injecting memory failure for pfn 0x20cb00 at process virtual address 0x7f763dd00000
     Memory failure: 0x20cb00: Killing dax-pmd:5421 due to hardware memory corruption
     Memory failure: 0x20cb00: recovery action for dax page: Recovered

  Given all the cross dependencies I propose taking this through
  nvdimm.git with acks from Naoya, x86/core, x86/RAS, and of course dax
  folks"

* tag 'libnvdimm-for-4.19_dax-memory-failure' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm, pmem: Restore page attributes when clearing errors
  x86/memory_failure: Introduce {set, clear}_mce_nospec()
  x86/mm/pat: Prepare {reserve, free}_memtype() for "decoy" addresses
  mm, memory_failure: Teach memory_failure() about dev_pagemap pages
  filesystem-dax: Introduce dax_lock_mapping_entry()
  mm, memory_failure: Collect mapping size in collect_procs()
  mm, madvise_inject_error: Let memory_failure() optionally take a page reference
  mm, dev_pagemap: Do not clear ->mapping on final put
  mm, madvise_inject_error: Disable MADV_SOFT_OFFLINE for ZONE_DEVICE pages
  filesystem-dax: Set page->index
  device-dax: Set page->index
  device-dax: Enable page_mapping()
  device-dax: Convert to vmf_insert_mixed and vm_fault_t

Pull libnvdimm updates from Dave Jiang:
 "Collection of misc libnvdimm patches for 4.19 submission:

   - Adding support to read locked nvdimm capacity.

   - Change test code to make DSM failure code injection an override.

   - Add support for calculate maximum contiguous area for namespace.

   - Add support for queueing a short ARS when there is on going ARS for
     nvdimm.

   - Allow NULL to be passed in to ->direct_access() for kaddr and pfn
     params.

   - Improve smart injection support for nvdimm emulation testing.

   - Fix test code that supports for emulating controller temperature.

   - Fix hang on error before devm_memremap_pages()

   - Fix a bug that causes user memory corruption when data returned to
     user for ars_status.

   - Maintainer updates for Ross Zwisler emails and adding Jan Kara to
     fsdax"

* tag 'libnvdimm-for-4.19_misc' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm: fix ars_status output length calculation
  device-dax: avoid hang on error before devm_memremap_pages()
  tools/testing/nvdimm: improve emulation of smart injection
  filesystem-dax: Do not request kaddr and pfn when not required
  md/dm-writecache: Don't request pointer dummy_addr when not required
  dax/super: Do not request a pointer kaddr when not required
  tools/testing/nvdimm: kaddr and pfn can be NULL to ->direct_access()
  s390, dcssblk: kaddr and pfn can be NULL to ->direct_access()
  libnvdimm, pmem: kaddr and pfn can be NULL to ->direct_access()
  acpi/nfit: queue issuing of ars when an uc error notification comes in
  libnvdimm: Export max available extent
  libnvdimm: Use max contiguous area for namespace size
  MAINTAINERS: Add Jan Kara for filesystem DAX
  MAINTAINERS: update Ross Zwisler's email address
  tools/testing/nvdimm: Fix support for emulating controller temperature
  tools/testing/nvdimm: Make DSM failure code injection an override
  acpi, nfit: Prefer _DSM over _LSR for namespace label reads
  libnvdimm: Introduce locked DIMM capacity support

Pull ARM SoC late updates from Olof Johansson:
 "A couple of late-merged changes that would be useful to get in this
  merge window:

   - Driver support for reset of audio complex on Meson platforms. The
     audio driver went in this merge window, and these changes have been
     in -next for a while (just not in our tree).

   - Power management fixes for IOMMU on Rockchip platforms, getting
     closer to kexec working on them, including Chromebooks.

   - Another pass updating "arm,psci" -> "psci" for some properties that
     have snuck in since last time it was done"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  iommu/rockchip: Move irq request past pm_runtime_enable
  iommu/rockchip: Handle errors returned from PM framework
  arm64: rockchip: Force CONFIG_PM on Rockchip systems
  ARM: rockchip: Force CONFIG_PM on Rockchip systems
  arm64: dts: Fix various entry-method properties to reflect documentation
  reset: imx7: Fix always writing bits as 0
  reset: meson: add meson audio arb driver
  reset: meson: add dt-bindings for meson-axg audio arb

Pull more Kbuild updates from Masahiro Yamada:

 - add build_{menu,n,g,x}config targets for compile-testing Kconfig

 - fix and improve recursive dependency detection in Kconfig

 - fix parallel building of menuconfig/nconfig

 - fix syntax error in clang-version.sh

 - suppress distracting log from syncconfig

 - remove obsolete "rpm" target

 - remove VMLINUX_SYMBOL(_STR) macro entirely

 - fix microblaze build with CONFIG_DYNAMIC_FTRACE

 - move compiler test for dead code/data elimination to Kconfig

 - rename well-known LDFLAGS variable to KBUILD_LDFLAGS

 - misc fixes and cleanups

* tag 'kbuild-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: rename LDFLAGS to KBUILD_LDFLAGS
  kbuild: pass LDFLAGS to recordmcount.pl
  kbuild: test dead code/data elimination support in Kconfig
  initramfs: move gen_initramfs_list.sh from scripts/ to usr/
  vmlinux.lds.h: remove stale <linux/export.h> include
  export.h: remove VMLINUX_SYMBOL() and VMLINUX_SYMBOL_STR()
  Coccinelle: remove pci_alloc_consistent semantic to detect in zalloc-simple.cocci
  kbuild: make sorting initramfs contents independent of locale
  kbuild: remove "rpm" target, which is alias of "rpm-pkg"
  kbuild: Fix LOADLIBES rename in Documentation/kbuild/makefiles.txt
  kconfig: suppress "configuration written to .config" for syncconfig
  kconfig: fix "Can't open ..." in parallel build
  kbuild: Add a space after `!` to prevent parsing as file pattern
  scripts: modpost: check memory allocation results
  kconfig: improve the recursive dependency report
  kconfig: report recursive dependency involving 'imply'
  kconfig: error out when seeing recursive dependency
  kconfig: add build-only configurator targets
  scripts/dtc: consolidate include path options in Makefile

Pull block fixes from Jens Axboe:
 "A few small fixes for this merge window:

   - Locking imbalance fix for bcache (Shan Hai)

   - A few small fixes for wbt. One is a cleanup/prep, one is a fix for
     an existing issue, and the last two are fixes for changes that went
     into this merge window (me)"

* tag 'for-linus-20180825' of git://git.kernel.dk/linux-block:
  blk-wbt: don't maintain inflight counts if disabled
  blk-wbt: fix has-sleeper queueing check
  blk-wbt: use wq_has_sleeper() for wq active check
  blk-wbt: move disable check into get_limit()
  bcache: release dc->writeback_lock properly in bch_writeback_thread()

Pull UBIFS fix from Richard Weinberger:
 "Remove an empty file from UBIFS source"

* tag 'upstream-4.19-rc1-fix' of git://git.infradead.org/linux-ubifs:
  ubifs: Remove empty file.h

Pull cifs fixes from Steve French:
 "Three small SMB3 fixes, one for stable"

* tag '4.19-rc-smb3' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number for cifs.ko to 2.12
  cifs: check kmalloc before use
  cifs: check if SMB2 PDU size has been padded and suppress the warning
  cifs: create a define for how many iovs we need for an SMB2_open()

This is not normally noticeable, but repeated forks are unnecessarily
expensive because they repeatedly dirty the parent page tables during
the page table copy operation.

It's trivial to just avoid write protecting the page table entry if it
was already not writable.

This patch was inspired by

    https://bugzilla.kernel.org/show_bug.cgi?id=200447

which points to an ancient "waste time re-doing fork" issue in the
presence of lots of signals.

That bug was fixed by Eric Biederman's signal handling series
culminating in commit c3ad2c3b ("signal: Don't restart fork when
signals come in"), but the unnecessary work for repeated forks is still
work just fixing, particularly since the fix is trivial.

Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

At the point where r is being checked for different values, r is always
going to be equal to 2 as the previous if statements jump to end or end1
if r is not 2.  Hence the assignment to err can be simplified to just
err an assignment without any checks on the value or r.

Detected by CoverityScan, CID#1226737 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Tejun Heo wrote:
>
> I asked Jens whether he could take care of the libata tree and he
> thankfully agreed, so, from now on, Jens will be the libata
> maintainer.
>
> Thanks a lot!

Thanks for your work in this area. I still remember the first linux
storage summit we did in Vancouver 2001, Tejun was invited to talk about
his libata error handling work. Before that, it was basically a crap
shoot if we recovered properly or not... A lot of water has flown under
the bridge since then!

Here's an "official" patch. Linus, can you apply it?
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull libata updates from Tejun Heo:
 "Nothing too interesting. Mostly ahci and ahci_platform changes, many
  around power management"

* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
  ata: ahci_platform: enable to get and control reset
  ata: libahci_platform: add reset control support
  ata: add an extra argument to ahci_platform_get_resources()
  ata: sata_rcar: Add r8a77965 support
  ata: sata_rcar: exclude setting of PHY registers in Gen3
  ata: sata_rcar: really mask all interrupts on Gen2 and later
  Revert "ata: ahci_platform: allow disabling of hotplug to save power"
  ata: libahci: Allow reconfigure of DEVSLP register
  ata: libahci: Correct setting of DEVSLP register
  ata: ahci: Enable DEVSLP by default on x86 with SLP_S0
  ata: ahci: Support state with min power but Partial low power state
  Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc"
  ata: sata_rcar: Add rudimentary Runtime PM support
  ata: sata_rcar: Provide a short-hand for &pdev->dev
  ata: Only output sg element mapped number in verbose debug
  ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUG
  ata: ahci_platform: convert kcalloc to devm_kcalloc
  ata: ahci_platform: convert kzallloc to kcalloc
  ata: ahci_platform: correct parameter documentation for ahci_platform_shutdown
  libata: remove ata_sff_data_xfer_noirq()
  ...

Pull cgroup updates from Tejun Heo:
 "Just one commit from Steven to take out spin lock from trace event
  handlers"

* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup/tracing: Move taking of spin lock out of trace event handlers

Pull workqueue updates from Tejun Heo:
 "Over the lockdep cross-release churn, workqueue lost some of the
  existing annotations. Johannes Berg restored it and also improved
  them"

* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: re-add lockdep dependencies for flushing
  workqueue: skip lockdep wq dependency in cancel_work_sync()

Pull IOMMU updates from Joerg Roedel:

 - PASID table handling updates for the Intel VT-d driver. It implements
   a global PASID space now so that applications usings multiple devices
   will just have one PASID.

 - A new config option to make iommu passthroug mode the default.

 - New sysfs attribute for iommu groups to export the type of the
   default domain.

 - A debugfs interface (for debug only) usable by IOMMU drivers to
   export internals to user-space.

 - R-Car Gen3 SoCs support for the ipmmu-vmsa driver

 - The ARM-SMMU now aborts transactions from unknown devices and devices
   not attached to any domain.

 - Various cleanups and smaller fixes all over the place.

* tag 'iommu-updates-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (42 commits)
  iommu/omap: Fix cache flushes on L2 table entries
  iommu: Remove the ->map_sg indirection
  iommu/arm-smmu-v3: Abort all transactions if SMMU is enabled in kdump kernel
  iommu/arm-smmu-v3: Prevent any devices access to memory without registration
  iommu/ipmmu-vmsa: Don't register as BUS IOMMU if machine doesn't have IPMMU-VMSA
  iommu/ipmmu-vmsa: Clarify supported platforms
  iommu/ipmmu-vmsa: Fix allocation in atomic context
  iommu: Add config option to set passthrough as default
  iommu: Add sysfs attribyte for domain type
  iommu/arm-smmu-v3: sync the OVACKFLG to PRIQ consumer register
  iommu/arm-smmu: Error out only if not enough context interrupts
  iommu/io-pgtable-arm-v7s: Abort allocation when table address overflows the PTE
  iommu/io-pgtable-arm: Fix pgtable allocation in selftest
  iommu/vt-d: Remove the obsolete per iommu pasid tables
  iommu/vt-d: Apply per pci device pasid table in SVA
  iommu/vt-d: Allocate and free pasid table
  iommu/vt-d: Per PCI device pasid table interfaces
  iommu/vt-d: Add for_each_device_domain() helper
  iommu/vt-d: Move device_domain_info to header
  iommu/vt-d: Apply global PASID in SVA
  ...

Pull thermal management updates from Zhang Rui:

 - Add Daniel Lezcano as the reviewer of thermal framework and SoC
   driver changes (Daniel Lezcano).

 - Fix a bug in intel_dts_soc_thermal driver, which does not translate
   IO-APIC GSI (Global System Interrupt) into Linux irq number (Hans de
   Goede).

 - For device tree bindings, allow cooling devices sharing same trip
   point with same contribution value to share cooling map (Viresh
   Kumar).

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  dt-bindings: thermal: Allow multiple devices to share cooling map
  MAINTAINERS: Add Daniel Lezcano as designated reviewer for thermal
  Thermal: Intel SoC DTS: Translate IO-APIC GSI number to linux irq number