Fix to return a negative error code from the usb_phy_generic_register()
error handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new phy-da8xx-usb driver to take the place of the mach code that
pokes CFGCHIP2 in the da8xx musb glue driver. This unbreaks the driver.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Simplify things a bit by using devm functions where possible.
Signed-off-by: David Lechner <david@lechnology.com>
[b-liu@ti.com: fixed merge conflict]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This allows run-time dr_mode switching support via the "mode" musb
sysfs attribute.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We can now just use PM runtime autoidle support as musb core
keeps things enabled when the devctl session bit is set. And
there's no need for dsps_musb_try_idle() so let's just remove
it.

Note that as cppi41 dma is clocked by musb, this only makes
PM work for dsps glue layer if CONFIG_MUSB_PIO_ONLY=y and
cppi41.ko is unloaded. This will get fixed when cppi41.c has
PM runtime implemented.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With musb core now blocking PM based on the devctl status
bit, we can remove related quirks from the 2430 glue layer
and simplify PM runtime further.

Lets's also use musb->controller instead of dev to make it
clear we make the PM runtime calls for the core, not the
glue layer.

And we can now also lower the autoidle timeout.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want to be polling the state when nothing is connected.
Let's change the polling logic in preparation for PM runtime
support.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: undo unnecessary line leading whitespace change]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want to keep musb enabled always when the session bit is
set. This simplifies the PM runtime and allows making it more
generic across the various glue layers.

So far the only exception to just following the session bit is
host mode disconnect where the session bit stays set.

In that case, just allow PM and let the PM runtime autoidle
timeout deal with it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: changed using dev_dbg() to musb_dbg()]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'extcon-next-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into usb-testing

Chanwoo writes:

Update extcon for 4.9

Detailed description for this pull request:
1. Support the extcon property and add the synchronization APIs.
- This feature supports the extcon property for external connector
  because each external connector might have the property according to
  the H/W design.

- The property name should keep the following style.
  : EXTCON_PROP_USB_[property_name]
  : EXTCON_PROP_CHG_[property_name]
  : EXTCON_PROP_JACK_[property_name]
  : EXTCON_PROP_DISP_[property_name]

- Add the new extcon APIs to support the extcon property.
  : extcon_set_property()
  : extcon_get_property()
  : extcon_set_property_capability()
  : extcon_get_property_capability()

- Add the new synchronization extcon APIs.
  : This feature adds the synchronization extcon APIs to support the noti
  for both state and property. When extcon_*_sync() functions is called,
  the extcon informs the information from extcon provider to extcon client.

  The extcon driver may need to change the both state and multiple properties
  at the same time. After setting the data of a external connector,
  the extcon send the notification to client driver with the extcon_*_sync().

  : extcon_sync()
  : extcon_set_state_sync()
  : extcon_set_property_sync()

- Change the name of existing APIs.
  : extcon_set_cable_state_() -> extcon_set_cable()
  : extcon_get_cable_state_() -> extcon_get_cable()

2. Add the extcon type to group the connector into five category.
- EXTCON_TYPE_USB  : USB connector
- EXTCON_TYPE_CHG  : Charger connector
- EXTCON_TYPE_JACK : Jack connector
- EXTCON_TYPE_DISP : Display connector
- EXTCON_TYPE_MISC : Miscellaneous connector

3. Add the new property for external connector.
- EXTCON_PROP_USB_VBUS
- EXTCON_PROP_USB_TYPEC_POLARITY
- EXTCON_PROP_USB_SS   (SuperSpeed)
- EXTCON_PROP_DISP_HPD (Hot Plug Detect)

4. Add the new type of external connector.
- EXTCON_DISP_DP  : Display Port
- EXTCON_DISP_HMD : Head Mounted Device
- EXTCON_CHG_WPT  : Wireless Power Transfer device

5. Add the new extcon driver.
- Qualcomm SPMI PMIC USB id detection driver detects whether
  EXTCON_USB_HOST is attached or detached. (extcon-qcom-spmi-mis.c)

6. Remove the usage of extcon_update_state() and old extcon_set_state()
- Both extcon_update_state() and extcon_set_state() should change the state
  of all external connectors with bit masking handling. It may occur the
  problem. Instead, extcon provides the extcon_set/get_state() functions.

7. Fix the minor issues on extcon drivers.

Some SATA to USB bridges fail to cooperate with some
drives resulting in no cache being present being reported
to the host. That causes the host to skip sending
a command to synchronize caches. That causes data loss
when the drive is powered down.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some Qualcomm PMICs have a misc device that performs USB id pin
detection via an interrupt. When the interrupt triggers, we
should read the interrupt line to see if it has gone high or low.
If the interrupt is low then the ID pin is grounded, and if the
interrupt is high then the ID pin is being held high.

Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
[cw00.choi: Edited the driver description and added the author information]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

This patch alters the renamed extcon API to set the state of the external
connectors instead of deprecated extcon_set_cable_state_().

Because the patch[1] modifies the function name to maintain the function
naming pattern.
- extcon_set_cable_state_() -> extcon_set_state_sync()
- extcon_get_cable_state_() -> extcon_get_state()

[1] https://lkml.org/lkml/2016/8/4/729
- extcon: Rename the extcon_set/get_state() to maintain the function naming pattern
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Roger Quadros <rogerq@ti.com>

This patch fixes the spelling mistake in dev_dbg messages.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
[cw00.choi: Modify the patch title/description]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact.  The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

EXTCON_PROP_DISP_HPD is need by display port, if the system has no hpd
interrupt, this property can be used.
- HPD (Hot Plug Detect) send the signal whether display device is on or off
  to source device.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
[cw00.choi: Add the description of HPD and full name of HPD]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>

Since ulpi bus driver is located at usb/common/ulpi.c, whether it
is compiled or not depends on CONFIG_USB_COMMON which needs either
USB Host or USB Gadget is enabled, so even CONFIG_USB_ULPI_BUS is
chosen, its source may still not be compiled when both USB HOST
and USB gadget are disabled.

It fixed compile error with below configurations:
- # CONFIG_USB is not set
- # CONFIG_USB_GADGET is not set
- CONFIG_PHY_TUSB1210=m
- CONFIG_USB_ULPI_BUS=m

>> All errors (new ones prefixed by >>):
>>
>> ERROR: "ulpi_unregister_driver" [drivers/phy/phy-tusb1210.ko] undefined!
>> ERROR: "__ulpi_register_driver" [drivers/phy/phy-tusb1210.ko] undefined!
>> ERROR: "ulpi_write" [drivers/phy/phy-tusb1210.ko] undefined!

Fixes: ad764c49 ("usb: Kconfig: move ulpi bus support out of host")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit aa719874 ("nvme: fabrics drivers don't need the nvme-pci
driver") removed the dependency on BLK_DEV_NVME, but the cdoe does
depend on the block layer (which used to be an implicit dependency
through BLK_DEV_NVME).

Otherwise you get various errors from the kbuild test robot random
config testing when that happens to hit a configuration with BLOCK
device support disabled.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Jay Freyensee <james_p_freyensee@linux.intel.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull IIO fixes from Greg KH:
 "Here are a few small IIO fixes for 4.8-rc6.

  Nothing major, full details are in the shortlog, all of these have
  been in linux-next with no reported issues"

* tag 'staging-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio:core: fix IIO_VAL_FRACTIONAL sign handling
  iio: ensure ret is initialized to zero before entering do loop
  iio: accel: kxsd9: Fix scaling bug
  iio: accel: bmc150: reset chip at init time
  iio: fix pressure data output unit in hid-sensor-attributes
  tools:iio:iio_generic_buffer: fix trigger-less mode

Pull USB fixes from Greg KH:
 "Here are some small USB gadget, phy, and xhci fixes for 4.8-rc6.

  All of these resolve minor issues that have been reported, and all
  have been in linux-next with no reported issues"

* tag 'usb-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: udc: fix NULL ptr dereference in isr_setup_status_phase
  xhci: fix null pointer dereference in stop command timeout function
  usb: dwc3: pci: fix build warning on !PM_SLEEP
  usb: gadget: prevent potenial null pointer dereference on skb->len
  usb: renesas_usbhs: fix clearing the {BRDY,BEMP}STS condition
  usb: phy: phy-generic: Check clk_prepare_enable() error
  usb: gadget: udc: renesas-usb3: clear VBOUT bit in DRD_CON
  Revert "usb: dwc3: gadget: always decrement by 1"

Pull libnvdimm fixes from Dan Williams:
 "nvdimm fixes for v4.8, two of them are tagged for -stable:

   - Fix devm_memremap_pages() to use track_pfn_insert().  Otherwise,
     DAX pmd mappings end up with an uncached pgprot, and unusable
     performance for the device-dax interface.  The device-dax interface
     appeared in 4.7 so this is tagged for -stable.

   - Fix a couple VM_BUG_ON() checks in the show_smaps() path to
     understand DAX pmd entries.  This fix is tagged for -stable.

   - Fix a mis-merge of the nfit machine-check handler to flip the
     polarity of an if() to match the final version of the patch that
     Vishal sent for 4.8-rc1.  Without this the nfit machine check
     handler never detects / inserts new 'badblocks' entries which
     applications use to identify lost portions of files.

   - For test purposes, fix the nvdimm_clear_poison() path to operate on
     legacy / simulated nvdimm memory ranges.  Without this fix a test
     can set badblocks, but never clear them on these ranges.

   - Fix the range checking done by dax_dev_pmd_fault().  This is not
     tagged for -stable since this problem is mitigated by specifying
     aligned resources at device-dax setup time.

  These patches have appeared in a next release over the past week.  The
  recent rebase you can see in the timestamps was to drop an invalid fix
  as identified by the updated device-dax unit tests [1].  The -mm
  touches have an ack from Andrew"

[1]: "[ndctl PATCH 0/3] device-dax test for recent kernel bugs"
   https://lists.01.org/pipermail/linux-nvdimm/2016-September/006855.html

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm: allow legacy (e820) pmem region to clear bad blocks
  nfit, mce: Fix SPA matching logic in MCE handler
  mm: fix cache mode of dax pmd mappings
  mm: fix show_smap() for zone_device-pmd ranges
  dax: fix mapping size check

Pull i2c fixes from Wolfram Sang:
 "Mostly driver bugfixes, but also a few cleanups which are nice to have
  out of the way"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: rk3x: Restore clock settings at resume time
  i2c: Spelling s/acknowedge/acknowledge/
  i2c: designware: save the preset value of DW_IC_SDA_HOLD
  Documentation: i2c: slave-interface: add note for driver development
  i2c: mux: demux-pinctrl: run properly with multiple instances
  i2c: bcm-kona: fix inconsistent indenting
  i2c: rcar: use proper device with dma_mapping_error
  i2c: sh_mobile: use proper device with dma_mapping_error
  i2c: mux: demux-pinctrl: invalidate properly when switching fails

Pull fscrypto fixes fromTed Ts'o:
 "Fix some brown-paper-bag bugs for fscrypto, including one one which
  allows a malicious user to set an encryption policy on an empty
  directory which they do not own"

* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  fscrypto: require write access to mount to set encryption policy
  fscrypto: only allow setting encryption policy on directories
  fscrypto: add authorization check for setting encryption policy

Since setting an encryption policy requires writing metadata to the
filesystem, it should be guarded by mnt_want_write/mnt_drop_write.
Otherwise, a user could cause a write to a frozen or readonly
filesystem.  This was handled correctly by f2fs but not by ext4.  Make
fscrypt_process_policy() handle it rather than relying on the filesystem
to get it right.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs}
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org>

The FS_IOC_SET_ENCRYPTION_POLICY ioctl allowed setting an encryption
policy on nondirectory files.  This was unintentional, and in the case
of nonempty regular files did not behave as expected because existing
data was not actually encrypted by the ioctl.

In the case of ext4, the user could also trigger filesystem errors in
->empty_dir(), e.g. due to mismatched "directory" checksums when the
kernel incorrectly tried to interpret a regular file as a directory.

This bug affected ext4 with kernels v4.8-rc1 or later and f2fs with
kernels v4.6 and later.  It appears that older kernels only permitted
directories and that the check was accidentally lost during the
refactoring to share the file encryption code between ext4 and f2fs.

This patch restores the !S_ISDIR() check that was present in older
kernels.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

On an ext4 or f2fs filesystem with file encryption supported, a user
could set an encryption policy on any empty directory(*) to which they
had readonly access.  This is obviously problematic, since such a
directory might be owned by another user and the new encryption policy
would prevent that other user from creating files in their own directory
(for example).

Fix this by requiring inode_owner_or_capable() permission to set an
encryption policy.  This means that either the caller must own the file,
or the caller must have the capability CAP_FOWNER.

(*) Or also on any regular file, for f2fs v4.6 and later and ext4
    v4.8-rc1 and later; a separate bug fix is coming for that.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs}
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Bad blocks can be injected via /sys/block/pmemN/badblocks. In a situation
where legacy pmem is being used or a pmem region created by using memmap
kernel parameter, the injected bad blocks are not cleared due to
nvdimm_clear_poison() failing from lack of ndctl function pointer. In
this case we need to just return as handled and allow the bad blocks to
be cleared rather than fail.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

The check for a 'pmem' type SPA in the MCE handler was inverted due to a
merge/rebase error.

Fixes: 6839a6d9 nfit: do an ARS scrub on hitting a latent media error
Cc: linux-acpi@vger.kernel.org
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

track_pfn_insert() in vmf_insert_pfn_pmd() is marking dax mappings as
uncacheable rendering them impractical for application usage.  DAX-pte
mappings are cached and the goal of establishing DAX-pmd mappings is to
attain more performance, not dramatically less (3 orders of magnitude).

track_pfn_insert() relies on a previous call to reserve_memtype() to
establish the expected page_cache_mode for the range.  While memremap()
arranges for reserve_memtype() to be called, devm_memremap_pages() does
not.  So, teach track_pfn_insert() and untrack_pfn() how to handle
tracking without a vma, and arrange for devm_memremap_pages() to
establish the write-back-cache reservation in the memtype tree.

Cc: <stable@vger.kernel.org>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Nilesh Choudhury <nilesh.choudhury@oracle.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Reported-by: Kai Zhang <kai.ka.zhang@oracle.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Attempting to dump /proc/<pid>/smaps for a process with pmd dax mappings
currently results in the following VM_BUG_ONs:

 kernel BUG at mm/huge_memory.c:1105!
 task: ffff88045f16b140 task.stack: ffff88045be14000
 RIP: 0010:[<ffffffff81268f9b>]  [<ffffffff81268f9b>] follow_trans_huge_pmd+0x2cb/0x340
 [..]
 Call Trace:
  [<ffffffff81306030>] smaps_pte_range+0xa0/0x4b0
  [<ffffffff814c2755>] ? vsnprintf+0x255/0x4c0
  [<ffffffff8123c46e>] __walk_page_range+0x1fe/0x4d0
  [<ffffffff8123c8a2>] walk_page_vma+0x62/0x80
  [<ffffffff81307656>] show_smap+0xa6/0x2b0

 kernel BUG at fs/proc/task_mmu.c:585!
 RIP: 0010:[<ffffffff81306469>]  [<ffffffff81306469>] smaps_pte_range+0x499/0x4b0
 Call Trace:
  [<ffffffff814c2795>] ? vsnprintf+0x255/0x4c0
  [<ffffffff8123c46e>] __walk_page_range+0x1fe/0x4d0
  [<ffffffff8123c8a2>] walk_page_vma+0x62/0x80
  [<ffffffff81307696>] show_smap+0xa6/0x2b0

These locations are sanity checking page flags that must be set for an
anonymous transparent huge page, but are not set for the zone_device
pages associated with dax mappings.

Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Pull virtio fixes from Michael Tsirkin:
 "This includes a couple of bugfixs for virtio.

  The virtio console patch is actually also in x86/tip targeting 4.9
  because it helps vmap stacks, but it also fixes IOMMU_PLATFORM which
  was added in 4.8, and it seems important not to ship that in a broken
  configuration"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_console: Stop doing DMA on the stack
  virtio: mark vring_dma_dev() static

Pull power management fixes from Rafael Wysocki:
 "This includes a PM QoS framework fix from Tejun to prevent interrupts
  from being enabled unexpectedly during early boot and a cpufreq
  documentation fix.

  Specifics:

   - If the PM QoS framework invokes cancel_delayed_work_sync() during
     early boot, it will enable interrupts which is not expected at that
     point, so prevent it from happening (Tejun Heo)

   - Fix cpufreq statistic documentation to follow a recent change in
     behavior that forgot to update it as appropriate (Jean Delvare)"

* tag 'pm-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq-stats: Minor documentation fix
  PM / QoS: avoid calling cancel_delayed_work_sync() during early boot

* pm-core-fixes:
  PM / QoS: avoid calling cancel_delayed_work_sync() during early boot

* pm-cpufreq-fixes:
  cpufreq-stats: Minor documentation fix

Pull GPIO fixes from Linus Walleij:
 "Some GPIO fixes that have been boiling the last two weeks or so.
  Nothing special, I'm trying to sort out some Kconfig business and
  Russell needs a fix in for -his SA1100 rework.

  Summary:

   - Revert a pointless attempt to add an include to solve the UM allyes
     compilation problem.

   - Make the mcp23s08 depend on OF_GPIO as it uses it and doesn't
     compile properly without it.

   - Fix a probing problem for ucb1x00"

* tag 'gpio-v4.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: sa1100: fix irq probing for ucb1x00
  gpio: mcp23s08: make driver depend on OF_GPIO
  Revert "gpio: include <linux/io-mapping.h> in gpiolib-of"

Pull fuse fix from Miklos Szeredi:
 "This fixes a deadlock when fuse, direct I/O and loop device are
  combined"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: direct-io: don't dirty ITER_BVEC pages

Pull overlayfs fix from Miklos Szeredi:
 "This fixes a regression caused by the last pull request"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: fix workdir creation

Pull btrfs fixes from Chris Mason:
 "I'm not proud of how long it took me to track down that one liner in
  btrfs_sync_log(), but the good news is the patches I was trying to
  blame for these problems were actually fine (sorry Filipe)"

* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: introduce tickets_id to determine whether asynchronous metadata reclaim work makes progress
  btrfs: remove root_log_ctx from ctx list before btrfs_sync_log returns
  btrfs: do not decrease bytes_may_use when replaying extents

Pull sound fixes from Takashi Iwai:
 "We've got quite a few fixes at this time, and all are stable patches.

  syzkaller strikes back again (episode 19 or so), and we had to plug
  some holes in ALSA core part (mostly timer).

  In addition, a couple of FireWire audio fixes for the invalid copy
  user calls in locks, and a few quirks for HD-audio and USB-audio as
  usual are included"

* tag 'sound-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: rawmidi: Fix possible deadlock with virmidi registration
  ALSA: timer: Fix zero-division by continue of uninitialized instance
  ALSA: timer: fix NULL pointer dereference in read()/ioctl() race
  ALSA: fireworks: accessing to user space outside spinlock
  ALSA: firewire-tascam: accessing to user space outside spinlock
  ALSA: hda - Enable subwoofer on Dell Inspiron 7559
  ALSA: hda - Add headset mic quirk for Dell Inspiron 5468
  ALSA: usb-audio: Add sample rate inquiry quirk for B850V3 CP2114
  ALSA: timer: fix NULL pointer dereference on memory allocation failure
  ALSA: timer: fix division by zero after SNDRV_TIMER_IOCTL_CONTINUE

virtio_console uses a small DMA buffer for control requests.  Move
that buffer into heap memory.

Doing virtio DMA on the stack is normally okay on non-DMA-API virtio
systems (which is currently most of them), but it breaks completely
if the stack is virtually mapped.

Tested by typing both directions using picocom aimed at /dev/hvc0.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>