- 28 Feb, 2020 40 commits
-
-
Geert Uytterhoeven authored
[ Upstream commit 02aeb2f2 ] pinmux_func_gpios[] contains a hole due to the missing function GPIO definition for the "CTX0&CTX1" signal, which is the logical "AND" of the first two CAN outputs. A closer look reveals other issues: - Some functionality is available on alternative pins, but the PINMUX_DATA() entries is using the wrong marks, - Several configurations are missing. Fix this by: - Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK, resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the corresponding enum IDs, - Adding all missing enum IDs and marks, - Use the right (*_PJ2x) variants for alternative pins, - Adding all missing configurations to pinmux_data[], - Adding all missing function GPIO definitions to pinmux_func_gpios[]. See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00: [1] Table 1.4 List of Pins [2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel (32 Mailboxes × 1 Channel), [3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as One Channel (96 Mailboxes × 1 Channel), [4] Table 48.3 Multiplexed Pins (Port B), [5] Table 48.4 Multiplexed Pins (Port C), [6] Table 48.10 Multiplexed Pins (Port J), [7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5). Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.beSigned-off-by:
Sasha Levin <sashal@kernel.org>
-
Chanwoo Choi authored
[ Upstream commit eff5d31f ] To build test, add COMPILE_TEST depedency to both ARM_RK3399_DMC_DEVFREQ and DEVFREQ_EVENT_ROCKCHIP_DFI configuration. And ARM_RK3399_DMC_DEVFREQ used the SMCCC interface so that add HAVE_ARM_SMCCC dependency to prevent the build break. Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by:
-
Valdis Klētnieks authored
[ Upstream commit bff47c23 ] When building with C=1, sparse issues a warning: CHECK arch/x86/entry/vdso/vdso32-setup.c arch/x86/entry/vdso/vdso32-setup.c:28:28: warning: symbol 'vdso32_enabled' was not declared. Should it be static? Provide the missing header file. Signed-off-by:
Valdis Kletnieks <valdis.kletnieks@vt.edu> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/36224.1575599767@turing-policeSigned-off-by:
-
Geert Uytterhoeven authored
[ Upstream commit 8443ffd1 ] Add a device node for the global timer, which is part of the Cortex-A9 MPCore. The global timer can serve as an accurate (4 ns) clock source for scheduling and delay loops. Signed-off-by:
-
Bibby Hsieh authored
[ Upstream commit 411f5c1e ] The driver currently handles vblank events only when updating planes on an already enabled CRTC. The atomic update API however allows requesting an event when enabling or disabling a CRTC. This currently leads to event objects being leaked in the kernel and to events not being sent out. Fix it. Signed-off-by:
Bibby Hsieh <bibby.hsieh@mediatek.com> Signed-off-by:
CK Hu <ck.hu@mediatek.com> Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit 4dbc96ad ] Clang warns: ../drivers/scsi/aic7xxx/aic7xxx_core.c:2317:5: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] if ((syncrate->sxfr_u2 & ST_SXFR) != 0) ^ ../drivers/scsi/aic7xxx/aic7xxx_core.c:2310:4: note: previous statement is here if (syncrate == &ahc_syncrates[maxsync]) ^ 1 warning generated. This warning occurs because there is a space amongst the tabs on this line. Remove it so that the indentation is consistent with the Linux kernel coding style and clang no longer warns. This has been a problem since the beginning of git history hence no fixes tag. Link: https://github.com/ClangBuiltLinux/linux/issues/817 Link: https://lore.kernel.org/r/20191218014220.52746-1-natechancellor@gmail.comSigned-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Erik Kaneda authored
[ Upstream commit 5ddbd771 ] ACPICA commit 29cc8dbc5463a93625bed87d7550a8bed8913bf4 create_buffer_field is a deferred op that is typically processed in load pass 2. However, disassembly of control method contents walk the parse tree with ACPI_PARSE_LOAD_PASS1 and AML_CREATE operators are processed in a later walk. This is a problem when there is a control method that has the same name as the AML_CREATE object. In this case, any use of the name segment will be detected as a method call rather than a reference to a buffer field. If this is detected as a method call, it can result in a mal-formed parse tree if the control methods have parameters. This change in processing AML_CREATE ops earlier solves this issue by inserting the named object in the ACPI namespace so that references to this name would be detected as a name string rather than a method call. Link: https://github.com/acpica/acpica/commit/29cc8dbcReported-by:
Elia Geretto <elia.f.geretto@gmail.com> Tested-by:
Bob Moore <robert.moore@intel.com> Signed-off-by:
Erik Kaneda <erik.kaneda@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Aditya Pakki authored
[ Upstream commit c705f9fc ] In ezusb_init, if upriv is NULL, the code crashes. However, the caller in ezusb_probe can handle the error and print the failure message. The patch replaces the BUG_ON call to error return. Signed-off-by:
Aditya Pakki <pakki001@umn.edu> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Phong Tran authored
[ Upstream commit cb775c88 ] correct usage prototype of callback in tasklet_init(). Report by https://github.com/KSPP/linux/issues/20Signed-off-by:
Phong Tran <tranmanphong@gmail.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Phong Tran authored
[ Upstream commit da5e57e8 ] correct usage prototype of callback in tasklet_init(). Report by https://github.com/KSPP/linux/issues/20Signed-off-by:
-
Phong Tran authored
[ Upstream commit ebd77feb ] correct usage prototype of callback in tasklet_init(). Report by https://github.com/KSPP/linux/issues/20Signed-off-by:
-
Phong Tran authored
[ Upstream commit 475eec11 ] correct usage prototype of callback in tasklet_init(). Report by https://github.com/KSPP/linux/issues/20Tested-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit df4654bd ] Clang warns: ../sound/usb/usx2y/usX2Yhwdep.c:122:3: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] info->version = USX2Y_DRIVER_VERSION; ^ ../sound/usb/usx2y/usX2Yhwdep.c:120:2: note: previous statement is here if (us428->chip_status & USX2Y_STAT_CHIP_INIT) ^ 1 warning generated. This warning occurs because there is a space before the tab on this line. Remove it so that the indentation is consistent with the Linux kernel coding style and clang no longer warns. This was introduced before the beginning of git history so no fixes tag. Link: https://github.com/ClangBuiltLinux/linux/issues/831Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Jan Kara authored
[ Upstream commit 4d5c1ada ] When we fail to allocate string for journal device name we jump to 'error' label which tries to unlock reiserfs write lock which is not held. Jump to 'error_unlocked' instead. Fixes: f32485be ("reiserfs: delay reiserfs lock until journal initialization") Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit afb34781 ] When building with Clang + -Wtautological-constant-compare, several of the ivtv and cx18 drivers warn along the lines of: drivers/media/pci/cx18/cx18-driver.c:1005:21: warning: converting the result of '<<' to a boolean always evaluates to true [-Wtautological-constant-compare] cx18_call_hw(cx, CX18_HW_GPIO_RESET_CTRL, ^ drivers/media/pci/cx18/cx18-cards.h:18:37: note: expanded from macro 'CX18_HW_GPIO_RESET_CTRL' #define CX18_HW_GPIO_RESET_CTRL (1 << 6) ^ 1 warning generated. This warning happens because the shift operation is implicitly converted to a boolean in v4l2_device_mask_call_all before being negated. This can be solved by just comparing the mask result to 0 explicitly so that there is no boolean conversion. The ultimate goal is to enable -Wtautological-compare globally because there are several subwarnings that would be helpful to have. For visual consistency and avoidance of these warnings in the future, all of the implicitly boolean conversions in the v4l2_device macros are converted to explicit ones as well. Link: https://github.com/ClangBuiltLinux/linux/issues/752Reviewed-by:
Ezequiel Garcia <ezequiel@collabora.com> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by:
-
Mao Wenan authored
[ Upstream commit 718eae27 ] Convert cpu_to_le16(le16_to_cpu(frame->datalen) + len) to use le16_add_cpu(), which is more concise and does the same thing. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Mao Wenan <maowenan@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Navid Emamdoost authored
[ Upstream commit 8c386cc8 ] In the implementation of pci_iov_add_virtfn() the allocated virtfn is leaked if pci_setup_device() fails. The error handling is not calling pci_stop_and_remove_bus_device(). Change the goto label to failed2. Fixes: 156c5532 ("PCI: Check for pci_setup_device() failure in pci_iov_add_virtfn()") Link: https://lore.kernel.org/r/20191125195255.23740-1-navid.emamdoost@gmail.comSigned-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Rasmus Villemoes authored
[ Upstream commit 148587a5 ] Qiang Zhao points out that these offsets get written to 16-bit registers, and there are some QE platforms with more than 64K muram. So it is possible that qe_muram_alloc() gives us an allocation that can't actually be used by the hardware, so detect and reject that. Reported-by:
Qiang Zhao <qiang.zhao@nxp.com> Reviewed-by:
Timur Tabi <timur@kernel.org> Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by:
Li Yang <leoyang.li@nxp.com> Signed-off-by:
-
Miquel Raynal authored
[ Upstream commit b8a039d3 ] RK808 can leverage a couple of GPIOs to tweak the ramp rate during DVS (Dynamic Voltage Scaling). These GPIOs are entirely optional but a dev_warn() appeared when cleaning this driver to use a more up-to-date gpiod API. At least reduce the log level to 'info' as it is totally fine to not populate these GPIO on a hardware design. This change is trivial but it is worth not polluting the logs during bringup phase by having real warnings and errors sorted out correctly. Fixes: a13eaf02 ("regulator: rk808: make better use of the gpiod API") Signed-off-by:
Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20191203164709.11127-1-miquel.raynal@bootlin.comSigned-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
yu kuai authored
drm/amdgpu: remove 4 set but not used variable in amdgpu_atombios_get_connector_info_from_object_table [ Upstream commit bae028e3 ] Fixes gcc '-Wunused-but-set-variable' warning: drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c: In function 'amdgpu_atombios_get_connector_info_from_object_table': drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:26: warning: variable 'grph_obj_num' set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:13: warning: variable 'grph_obj_id' set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:37: warning: variable 'con_obj_type' set but not used [-Wunused-but-set-variable] drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:24: warning: variable 'con_obj_num' set but not used [-Wunused-but-set-variable] They are never used, so can be removed. Fixes: d38ceaf9 ("drm/amdgpu: add core driver (v4)") Signed-off-by:
yu kuai <yukuai3@huawei.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Douglas Anderson authored
[ Upstream commit 908b0501 ] When I got my clock parenting slightly wrong I ended up with a crash that looked like this: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 ... pc : clk_hw_get_rate+0x14/0x44 ... Call trace: clk_hw_get_rate+0x14/0x44 _freq_tbl_determine_rate+0x94/0xfc clk_rcg2_determine_rate+0x2c/0x38 clk_core_determine_round_nolock+0x4c/0x88 clk_core_round_rate_nolock+0x6c/0xa8 clk_core_round_rate_nolock+0x9c/0xa8 clk_core_set_rate_nolock+0x70/0x180 clk_set_rate+0x3c/0x6c of_clk_set_defaults+0x254/0x360 platform_drv_probe+0x28/0xb0 really_probe+0x120/0x2dc driver_probe_device+0x64/0xfc device_driver_attach+0x4c/0x6c __driver_attach+0xac/0xc0 bus_for_each_dev+0x84/0xcc driver_attach+0x2c/0x38 bus_add_driver+0xfc/0x1d0 driver_register+0x64/0xf8 __platform_driver_register+0x4c/0x58 msm_drm_register+0x5c/0x60 ... It turned out that clk_hw_get_parent_by_index() was returning NULL and we weren't checking. Let's check it so that we don't crash. Fixes: ac269395 ("clk: qcom: Convert to clk_hw based provider APIs") Signed-off-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
Matthias Kaehlcke <mka@chromium.org> Link: https://lkml.kernel.org/r/20200203103049.v4.1.I7487325fe8e701a68a07d3be8a6a4b571eca9cfa@changeidSigned-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Masahiro Yamada authored
[ Upstream commit c8fb7d7e ] Running randconfig on arm64 using KCONFIG_SEED=0x40C5E904 (e.g. on v5.5) produces the .config with CONFIG_EFI=y and CONFIG_CPU_BIG_ENDIAN=y, which does not meet the !CONFIG_CPU_BIG_ENDIAN dependency. This is because the user choice for CONFIG_CPU_LITTLE_ENDIAN vs CONFIG_CPU_BIG_ENDIAN is set by randomize_choice_values() after the value of CONFIG_EFI is calculated. When this happens, the has_changed flag should be set. Currently, it takes the result from the last iteration. It should accumulate all the results of the loop. Fixes: 3b9a19e0 ("kconfig: loop as long as we changed some symbols in randconfig") Reported-by:
Vincenzo Frascino <vincenzo.frascino@arm.com> Signed-off-by:
Masahiro Yamada <masahiroy@kernel.org> Signed-off-by:
-
zhangyi (F) authored
[ Upstream commit 51f57b01 ] JBD2_REC_ERR flag used to indicate the errno has been updated when jbd2 aborted, and then __ext4_abort() and ext4_handle_error() can invoke panic if ERRORS_PANIC is specified. But if the journal has been aborted with zero errno, jbd2_journal_abort() didn't set this flag so we can no longer panic. Fix this by always record the proper errno in the journal superblock. Fixes: 4327ba52 ("ext4, jbd2: ensure entering into panic after recording an error in superblock") Signed-off-by:
zhangyi (F) <yi.zhang@huawei.com> Reviewed-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Steven Rostedt (VMware) authored
[ Upstream commit dfb6cd1e ] Looking through old emails in my INBOX, I came across a patch from Luis Henriques that attempted to fix a race of two stat tracers registering the same stat trace (extremely unlikely, as this is done in the kernel, and probably doesn't even exist). The submitted patch wasn't quite right as it needed to deal with clean up a bit better (if two stat tracers were the same, it would have the same files). But to make the code cleaner, all we needed to do is to keep the all_stat_sessions_mutex held for most of the registering function. Link: http://lkml.kernel.org/r/1410299375-20068-1-git-send-email-luis.henriques@canonical.com Fixes: 002bb86d ("tracing/ftrace: separate events tracing and stats tracing engine") Reported-by:
Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Luis Henriques authored
[ Upstream commit afccc00f ] tracing_stat_init() was always returning '0', even on the error paths. It now returns -ENODEV if tracing_init_dentry() fails or -ENOMEM if it fails to created the 'trace_stat' debugfs directory. Link: http://lkml.kernel.org/r/1410299381-20108-1-git-send-email-luis.henriques@canonical.com Fixes: ed6f1c99 ("tracing: Check return value of tracing_init_dentry()") Signed-off-by:
-
Arvind Sankar authored
[ Upstream commit dacc9092 ] When checking whether the reported lfb_size makes sense, the height * stride result is page-aligned before seeing whether it exceeds the reported size. This doesn't work if height * stride is not an exact number of pages. For example, as reported in the kernel bugzilla below, an 800x600x32 EFI framebuffer gets skipped because of this. Move the PAGE_ALIGN to after the check vs size. Reported-by:
Christopher Head <chead@chead.ca> Tested-by:
Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by:
-
Kai Li authored
[ Upstream commit a09decff ] If the journal is dirty when the filesystem is mounted, jbd2 will replay the journal but the journal superblock will not be updated by journal_reset() because JBD2_ABORT flag is still set (it was set in journal_init_common()). This is problematic because when a new transaction is then committed, it will be recorded in block 1 (journal->j_tail was set to 1 in journal_reset()). If unclean shutdown happens again before the journal superblock is updated, the new recorded transaction will not be replayed during the next mount (because of stale sb->s_start and sb->s_sequence values) which can lead to filesystem corruption. Fixes: 85e0c4e8 ("jbd2: if the journal is aborted then don't allow update of the log tail") Signed-off-by:
Kai Li <li.kai4@h3c.com> Link: https://lore.kernel.org/r/20200111022542.5008-1-li.kai4@h3c.comSigned-off-by:
-
Jia-Ju Bai authored
[ Upstream commit 9c1ed62a ] The driver may sleep while holding a spinlock. The function call path (from bottom to top) in Linux 4.19 is: drivers/usb/gadget/udc/core.c, 1175: kzalloc(GFP_KERNEL) in usb_add_gadget_udc_release drivers/usb/gadget/udc/core.c, 1272: usb_add_gadget_udc_release in usb_add_gadget_udc drivers/usb/gadget/udc/gr_udc.c, 2186: usb_add_gadget_udc in gr_probe drivers/usb/gadget/udc/gr_udc.c, 2183: spin_lock in gr_probe drivers/usb/gadget/udc/core.c, 1195: mutex_lock in usb_add_gadget_udc_release drivers/usb/gadget/udc/core.c, 1272: usb_add_gadget_udc_release in usb_add_gadget_udc drivers/usb/gadget/udc/gr_udc.c, 2186: usb_add_gadget_udc in gr_probe drivers/usb/gadget/udc/gr_udc.c, 2183: spin_lock in gr_probe drivers/usb/gadget/udc/gr_udc.c, 212: debugfs_create_file in gr_probe drivers/usb/gadget/udc/gr_udc.c, 2197: gr_dfs_create in gr_probe drivers/usb/gadget/udc/gr_udc.c, 2183: spin_lock in gr_probe drivers/usb/gadget/udc/gr_udc.c, 2114: devm_request_threaded_irq in gr_request_irq drivers/usb/gadget/udc/gr_udc.c, 2202: gr_request_irq in gr_probe drivers/usb/gadget/udc/gr_udc.c, 2183: spin_lock in gr_probe kzalloc(GFP_KERNEL), mutex_lock(), debugfs_create_file() and devm_request_threaded_irq() can sleep at runtime. To fix these possible bugs, usb_add_gadget_udc(), gr_dfs_create() and gr_request_irq() are called without handling the spinlock. These bugs are found by a static analysis tool STCheck written by myself. Signed-off-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by:
Felipe Balbi <balbi@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Jia-Ju Bai authored
[ Upstream commit b7435128 ] The driver may sleep while holding a spinlock. The function call path (from bottom to top) in Linux 4.19 is: kernel/irq/manage.c, 523: synchronize_irq in disable_irq drivers/uio/uio_dmem_genirq.c, 140: disable_irq in uio_dmem_genirq_irqcontrol drivers/uio/uio_dmem_genirq.c, 134: _raw_spin_lock_irqsave in uio_dmem_genirq_irqcontrol synchronize_irq() can sleep at runtime. To fix this bug, disable_irq() is called without holding the spinlock. This bug is found by a static analysis tool STCheck written by myself. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 548f0b9a ] This fixes build errors of all sorts. Also, emit .exit.text unconditionally. Signed-off-by:
-
Tiezhu Yang authored
[ Upstream commit 72d052e2 ] If kzalloc fails, it should return -ENOMEM, otherwise may trigger a NULL pointer dereference. Fixes: 3adeb256 ("MIPS: Loongson: Improve LEFI firmware interface") Signed-off-by:
Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by:
Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Huacai Chen <chenhc@lemote.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Ard Biesheuvel authored
[ Upstream commit ffc2760b ] Fix a couple of issues with the way we map and copy the vendor string: - we map only 2 bytes, which usually works since you get at least a page, but if the vendor string happens to cross a page boundary, a crash will result - only call early_memunmap() if early_memremap() succeeded, or we will call it with a NULL address which it doesn't like, - while at it, switch to early_memremap_ro(), and array indexing rather than pointer dereferencing to read the CHAR16 characters. Signed-off-by:
Ard Biesheuvel <ardb@kernel.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Matthew Garrett <mjg59@google.com> Cc: linux-efi@vger.kernel.org Fixes: 5b83683f ("x86: EFI runtime service support") Link: https://lkml.kernel.org/r/20200103113953.9571-5-ardb@kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Hans de Goede authored
[ Upstream commit a2368059 ] Suspending Goodix touchscreens requires changing the interrupt pin to output before sending them a power-down command. Followed by wiggling the interrupt pin to wake the device up, after which it is put back in input mode. On Bay Trail devices with a Goodix touchscreen direct-irq mode is used in combination with listing the pin as a normal GpioIo resource. This works fine, until the goodix driver gets rmmod-ed and then insmod-ed again. In this case byt_gpio_disable_free() calls byt_gpio_clear_triggering() which clears the IRQ flags and after that the (direct) IRQ no longer triggers. This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag to byt_gpio_clear_triggering(). Note that byt_gpio_clear_triggering() only gets called from byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded from the irq_valid mask by byt_init_irq_valid_mask(). Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Jia-Ju Bai authored
[ Upstream commit bb6d4206 ] The driver may sleep while holding a spinlock. The function call path (from bottom to top) in Linux 4.19 is: drivers/media/platform/sti/bdisp/bdisp-hw.c, 385: msleep in bdisp_hw_reset drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 341: bdisp_hw_reset in bdisp_device_run drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 317: _raw_spin_lock_irqsave in bdisp_device_run To fix this bug, msleep() is replaced with udelay(). This bug is found by a static analysis tool STCheck written by myself. Signed-off-by:
Fabien Dessenne <fabien.dessenne@st.com> Signed-off-by:
-
Jia-Ju Bai authored
[ Upstream commit e36eaf94 ] The driver may sleep while holding a spinlock. The function call path (from bottom to top) in Linux 4.19 is: drivers/gpio/gpio-grgpio.c, 261: request_irq in grgpio_irq_map drivers/gpio/gpio-grgpio.c, 255: _raw_spin_lock_irqsave in grgpio_irq_map drivers/gpio/gpio-grgpio.c, 318: free_irq in grgpio_irq_unmap drivers/gpio/gpio-grgpio.c, 299: _raw_spin_lock_irqsave in grgpio_irq_unmap request_irq() and free_irq() can sleep at runtime. To fix these bugs, request_irq() and free_irq() are called without holding the spinlock. These bugs are found by a static analysis tool STCheck written by myself. Signed-off-by:
-
Oliver O'Halloran authored
[ Upstream commit 3b5b9997 ] On pseries there is a bug with adding hotplugged devices to an IOMMU group. For a number of dumb reasons fixing that bug first requires re-working how VFs are configured on PowerNV. For background, on PowerNV we use the pcibios_sriov_enable() hook to do two things: 1. Create a pci_dn structure for each of the VFs, and 2. Configure the PHB's internal BARs so the MMIO range for each VF maps to a unique PE. Roughly speaking a PE is the hardware counterpart to a Linux IOMMU group since all the devices in a PE share the same IOMMU table. A PE also defines the set of devices that should be isolated in response to a PCI error (i.e. bad DMA, UR/CA, AER events, etc). When isolated all MMIO and DMA traffic to and from devicein the PE is blocked by the root complex until the PE is recovered by the OS. The requirement to block MMIO causes a giant headache because the P8 PHB generally uses a fixed mapping between MMIO addresses and PEs. As a result we need to delay configuring the IOMMU groups for device until after MMIO resources are assigned. For physical devices (i.e. non-VFs) the PE assignment is done in pcibios_setup_bridge() which is called immediately after the MMIO resources for downstream devices (and the bridge's windows) are assigned. For VFs the setup is more complicated because: a) pcibios_setup_bridge() is not called again when VFs are activated, and b) The pci_dev for VFs are created by generic code which runs after pcibios_sriov_enable() is called. The work around for this is a two step process: 1. A fixup in pcibios_add_device() is used to initialised the cached pe_number in pci_dn, then 2. A bus notifier then adds the device to the IOMMU group for the PE specified in pci_dn->pe_number. A side effect fixing the pseries bug mentioned in the first paragraph is moving the fixup out of pcibios_add_device() and into pcibios_bus_add_device(), which is called much later. This results in step 2. failing because pci_dn->pe_number won't be initialised when the bus notifier is run. We can fix this by removing the need for the fixup. The PE for a VF is known before the VF is even scanned so we can initialise pci_dn->pe_number pcibios_sriov_enable() instead. Unfortunately, moving the initialisation causes two problems: 1. We trip the WARN_ON() in the current fixup code, and 2. The EEH core clears pdn->pe_number when recovering a VF and relies on the fixup to correctly re-set it. The only justification for either of these is a comment in eeh_rmv_device() suggesting that pdn->pe_number *must* be set to IODA_INVALID_PE in order for the VF to be scanned. However, this comment appears to have no basis in reality. Both bugs can be fixed by just deleting the code. Tested-by:
Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by:
Oliver O'Halloran <oohall@gmail.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191028085424.12006-1-oohall@gmail.comSigned-off-by:
-
Eugen Hristev authored
[ Upstream commit 1451d5ae ] This driver supports both the mt9v032 (color) and the mt9v022 (mono) sensors. Depending on which sensor is used, the format from the sensor is different. The format.code inside the dev struct holds this information. The enum mbus and enum frame sizes need to take into account both type of sensors, not just the color one. To solve this, use the format.code in these functions instead of the hardcoded bayer color format (which is only used for mt9v032). [Sakari Ailus: rewrapped commit message] Suggested-by:
Wenyou Yang <wenyou.yang@microchip.com> Signed-off-by:
Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit 3c911fe7 ] In the probe function, some resources are allocated using 'dma_alloc_wc()', they should be released with 'dma_free_wc()', not 'dma_free_coherent()'. We already use 'dma_free_wc()' in the remove function, but not in the error handling path of the probe function. Also, remove a useless 'PAGE_ALIGN()'. 'info->fix.smem_len' is already PAGE_ALIGNed. Fixes: 638772c7 ("fb: add support of LCD display controller on pxa168/910 (base layer)") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
Lubomir Rintel <lkundrak@v3.sk> CC: YueHaibing <yuehaibing@huawei.com> Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190831100024.3248-1-christophe.jaillet@wanadoo.frSigned-off-by:
-
Geert Uytterhoeven authored
[ Upstream commit 55b1cb1f ] pinmux_func_gpios[] contains a hole due to the missing function GPIO definition for the "CTX0&CTX1" signal, which is the logical "AND" of the two CAN outputs. Fix this by: - Renaming CRX0_CRX1_MARK to CTX0_CTX1_MARK, as PJ2MD[2:0]=010 configures the combined "CTX0&CTX1" output signal, - Renaming CRX0X1_MARK to CRX0_CRX1_MARK, as PJ3MD[1:0]=10 configures the shared "CRX0/CRX1" input signal, which is fed to both CAN inputs, - Adding the missing function GPIO definition for "CTX0&CTX1" to pinmux_func_gpios[], - Moving all CAN enums next to each other. See SH7262 Group, SH7264 Group User's Manual: Hardware, Rev. 4.00: [1] Figure 1.2 (3) (Pin Assignment for the SH7264 Group (1-Mbyte Version), [2] Figure 1.2 (4) Pin Assignment for the SH7264 Group (640-Kbyte Version, [3] Table 1.4 List of Pins, [4] Figure 20.29 Connection Example when Using This Module as 1-Channel Module (64 Mailboxes x 1 Channel), [5] Table 32.10 Multiplexed Pins (Port J), [6] Section 32.2.30 (3) Port J Control Register 0 (PJCR0). Note that the last 2 disagree about PJ2MD[2:0], which is probably the root cause of this bug. But considering [4], "CTx0&CTx1" in [5] must be correct, and "CRx0&CRx1" in [6] must be wrong. Signed-off-by:
-
Vladimir Oltean authored
[ Upstream commit c26a2c2d ] The driver wrongly assumes that it is the only entity that can set the SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the gfar_clean_tx_ring function, where the TX timestamp is collected if necessary, the aforementioned bit is used to discriminate whether or not the TX timestamp should be delivered to the socket's error queue. But a stacked driver such as a DSA switch can also set the SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in order to denote that the hardware timestamping process is undergoing. Therefore, gianfar would misinterpret the "in progress" bit as being its own, and deliver a second skb clone in the socket's error queue, completely throwing off a PTP process which is not expecting to receive it, _even though_ TX timestamping is not enabled for gianfar. There have been discussions [0] as to whether non-MAC drivers need or not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2 timestamps, a sw and a hw one, to applications which only expect one). But as of this patch, there are at least 2 PTP drivers that would break in conjunction with gianfar: the sja1105 DSA switch and the felix switch, by way of its ocelot core driver. So regardless of that conclusion, fix the gianfar driver to not do stuff based on flags set by others and not intended for it. [0]: https://www.spinics.net/lists/netdev/msg619699.html Fixes: f0ee7acf ("gianfar: Add hardware TX timestamping support") Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
