- 16 Aug, 2016 14 commits
-
-
James Bottomley authored
commit a621bac3 upstream. When SCSI was written, all commands coming from the filesystem (REQ_TYPE_FS commands) had data. This meant that our signal for needing to complete the command was the number of bytes completed being equal to the number of bytes in the request. Unfortunately, with the advent of flush barriers, we can now get zero length REQ_TYPE_FS commands, which confuse this logic because they satisfy the condition every time. This means they never get retried even for retryable conditions, like UNIT ATTENTION because we complete them early assuming they're done. Fix this by special casing the early completion condition to recognise zero length commands with errors and let them drop through to the retry code. Reported-by:
Sebastian Parschauer <s.parschauer@gmx.de> Signed-off-by:
James E.J. Bottomley <jejb@linux.vnet.ibm.com> Tested-by:
Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> [ jwang: backport from upstream 4.7 to fix scsi resize issue ] Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Christoph Hellwig authored
commit bc85dc50 upstream. By folding scsi_end_request into its only caller we can significantly clean up the completion logic. We can use simple goto labels now to only have a single place to finish or requeue command there instead of the previous convoluted logic. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Nicholas Bellinger <nab@linux-iscsi.org> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Reviewed-by:
Hannes Reinecke <hare@suse.de> [jwang: backport to 3.12] Signed-off-by:
-
Theodore Ts'o authored
commit 86a574de upstream. Don't allow RNDADDTOENTCNT or RNDADDENTROPY to accept a negative entropy value. It doesn't make any sense to subtract from the entropy counter, and it can trigger a warning: random: negative entropy/overflow: pool input count -40000 ------------[ cut here ]------------ WARNING: CPU: 3 PID: 6828 at drivers/char/random.c:670[< none >] credit_entropy_bits+0x21e/0xad0 drivers/char/random.c:670 Modules linked in: CPU: 3 PID: 6828 Comm: a.out Not tainted 4.7.0-rc4+ #4 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 ffffffff880b58e0 ffff88005dd9fcb0 ffffffff82cc838f ffffffff87158b40 fffffbfff1016b1c 0000000000000000 0000000000000000 ffffffff87158b40 ffffffff83283dae 0000000000000009 ffff88005dd9fcf8 ffffffff8136d27f Call Trace: [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffff82cc838f>] dump_stack+0x12e/0x18f lib/dump_stack.c:51 [<ffffffff8136d27f>] __warn+0x19f/0x1e0 kernel/panic.c:516 [<ffffffff8136d48c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:551 [<ffffffff83283dae>] credit_entropy_bits+0x21e/0xad0 drivers/char/random.c:670 [< inline >] credit_entropy_bits_safe drivers/char/random.c:734 [<ffffffff8328785d>] random_ioctl+0x21d/0x250 drivers/char/random.c:1546 [< inline >] vfs_ioctl fs/ioctl.c:43 [<ffffffff8185316c>] do_vfs_ioctl+0x18c/0xff0 fs/ioctl.c:674 [< inline >] SYSC_ioctl fs/ioctl.c:689 [<ffffffff8185405f>] SyS_ioctl+0x8f/0xc0 fs/ioctl.c:680 [<ffffffff86a995c0>] entry_SYSCALL_64_fastpath+0x23/0xc1 arch/x86/entry/entry_64.S:207 ---[ end trace 5d4902b2ba842f1f ]--- This was triggered using the test program: // autogenerated by syzkaller (http://github.com/google/syzkaller) int main() { int fd = open("/dev/random", O_RDWR); int val = -5000; ioctl(fd, RNDADDTOENTCNT, &val); return 0; } It's harmless in that (a) only root can trigger it, and (b) after complaining the code never does let the entropy count go negative, but it's better to simply not allow this userspace from passing in a negative entropy value altogether. Google-Bug-Id: #29575089 Reported-By:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
John Johansen authored
commit 0b938a2e upstream. Signed-off-by:
John Johansen <john.johansen@canonical.com> Acked-by:
Seth Arnold <seth.arnold@canonical.com> Signed-off-by:
-
David Howells authored
commit 20f06ed9 upstream. MIPS64 needs to use compat_sys_keyctl for 32-bit userspace rather than calling sys_keyctl. The latter will work in a lot of cases, thereby hiding the issue. Reported-by:
Stephan Mueller <smueller@chronox.de> Signed-off-by:
David Howells <dhowells@redhat.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: linux-security-module@vger.kernel.org Cc: keyrings@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13832/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Dave Weinstein authored
commit 7de24996 upstream. Add access checks to sys_oabi_epoll_wait() and sys_oabi_semtimedop(). This fixes CVE-2016-3857, a local privilege escalation under CONFIG_OABI_COMPAT. Reported-by:
Chiachih Wu <wuchiachih@gmail.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
Nicolas Pitre <nico@linaro.org> Signed-off-by:
Dave Weinstein <olorin@google.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Greg Kroah-Hartman authored
Ben Hutchings reported that commit ddbe1fca ("USB: Add device quirk for ASUS T100 Base Station keyboard") was incorrectly ported. This patch fixes up the quirk by putting it in the correct table. Reported-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Bjørn Mork authored
commit 4d06dd53 upstream. usbnet_link_change will call schedule_work and should be avoided if bind is failing. Otherwise we will end up with scheduled work referring to a netdev which has gone away. Instead of making the call conditional, we can just defer it to usbnet_probe, using the driver_info flag made for this purpose. Fixes: 8a34b0ae ("usbnet: cdc_ncm: apply usbnet_link_change") Reported-by:
Andrey Konovalov <andreyknvl@gmail.com> Suggested-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
David S. Miller <davem@davemloft.net> [ciwillia@brocade.com: backported to 3.14: adjusted context] Signed-off-by:
Charles (Chas) Williams <ciwillia@brocade.com> Signed-off-by:
-
Andy Lutomirski authored
commit 4eaffdd5 upstream. My previous comments were still a bit confusing and there was a typo. Fix it up. Reported-by:
Peter Zijlstra <peterz@infradead.org> Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: 71b3c126 ("x86/mm: Add barriers and document switch_mm()-vs-flush synchronization") Link: http://lkml.kernel.org/r/0a0b43cdcdd241c5faaaecfbcc91a155ddedc9a1.1452631609.git.luto@kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Karl Heiss authored
commit 635682a1 upstream. A case can occur when sctp_accept() is called by the user during a heartbeat timeout event after the 4-way handshake. Since sctp_assoc_migrate() changes both assoc->base.sk and assoc->ep, the bh_sock_lock in sctp_generate_heartbeat_event() will be taken with the listening socket but released with the new association socket. The result is a deadlock on any future attempts to take the listening socket lock. Note that this race can occur with other SCTP timeouts that take the bh_lock_sock() in the event sctp_accept() is called. BUG: soft lockup - CPU#9 stuck for 67s! [swapper:0] ... RIP: 0010:[<ffffffff8152d48e>] [<ffffffff8152d48e>] _spin_lock+0x1e/0x30 RSP: 0018:ffff880028323b20 EFLAGS: 00000206 RAX: 0000000000000002 RBX: ffff880028323b20 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff880028323be0 RDI: ffff8804632c4b48 RBP: ffffffff8100bb93 R08: 0000000000000000 R09: 0000000000000000 R10: ffff880610662280 R11: 0000000000000100 R12: ffff880028323aa0 R13: ffff8804383c3880 R14: ffff880028323a90 R15: ffffffff81534225 FS: 0000000000000000(0000) GS:ffff880028320000(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 00000000006df528 CR3: 0000000001a85000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process swapper (pid: 0, threadinfo ffff880616b70000, task ffff880616b6cab0) Stack: ffff880028323c40 ffffffffa01c2582 ffff880614cfb020 0000000000000000 <d> 0100000000000000 00000014383a6c44 ffff8804383c3880 ffff880614e93c00 <d> ffff880614e93c00 0000000000000000 ffff8804632c4b00 ffff8804383c38b8 Call Trace: <IRQ> [<ffffffffa01c2582>] ? sctp_rcv+0x492/0xa10 [sctp] [<ffffffff8148c559>] ? nf_iterate+0x69/0xb0 [<ffffffff814974a0>] ? ip_local_deliver_finish+0x0/0x2d0 [<ffffffff8148c716>] ? nf_hook_slow+0x76/0x120 [<ffffffff814974a0>] ? ip_local_deliver_finish+0x0/0x2d0 [<ffffffff8149757d>] ? ip_local_deliver_finish+0xdd/0x2d0 [<ffffffff81497808>] ? ip_local_deliver+0x98/0xa0 [<ffffffff81496ccd>] ? ip_rcv_finish+0x12d/0x440 [<ffffffff81497255>] ? ip_rcv+0x275/0x350 [<ffffffff8145cfeb>] ? __netif_receive_skb+0x4ab/0x750 ... With lockdep debugging: ===================================== [ BUG: bad unlock balance detected! ] ------------------------------------- CslRx/12087 is trying to release lock (slock-AF_INET) at: [<ffffffffa01bcae0>] sctp_generate_timeout_event+0x40/0xe0 [sctp] but there are no more locks to release! other info that might help us debug this: 2 locks held by CslRx/12087: #0: (&asoc->timers[i]){+.-...}, at: [<ffffffff8108ce1f>] run_timer_softirq+0x16f/0x3e0 #1: (slock-AF_INET){+.-...}, at: [<ffffffffa01bcac3>] sctp_generate_timeout_event+0x23/0xe0 [sctp] Ensure the socket taken is also the same one that is released by saving a copy of the socket before entering the timeout event critical section. Signed-off-by:
Karl Heiss <kheiss@gmail.com> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com> (cherry picked from commit 013dd9e0) Signed-off-by:
Chas Williams <3chas3@gmail.com> Signed-off-by:
-
Andy Lutomirski authored
commit 71b3c126 upstream. When switch_mm() activates a new PGD, it also sets a bit that tells other CPUs that the PGD is in use so that TLB flush IPIs will be sent. In order for that to work correctly, the bit needs to be visible prior to loading the PGD and therefore starting to fill the local TLB. Document all the barriers that make this work correctly and add a couple that were missing. Signed-off-by:
-
Tejun Heo authored
commit 8d91f8b1 upstream. @console_may_schedule tracks whether console_sem was acquired through lock or trylock. If the former, we're inside a sleepable context and console_conditional_schedule() performs cond_resched(). This allows console drivers which use console_lock for synchronization to yield while performing time-consuming operations such as scrolling. However, the actual console outputting is performed while holding irq-safe logbuf_lock, so console_unlock() clears @console_may_schedule before starting outputting lines. Also, only a few drivers call console_conditional_schedule() to begin with. This means that when a lot of lines need to be output by console_unlock(), for example on a console registration, the task doing console_unlock() may not yield for a long time on a non-preemptible kernel. If this happens with a slow console devices, for example a serial console, the outputting task may occupy the cpu for a very long time. Long enough to trigger softlockup and/or RCU stall warnings, which in turn pile more messages, sometimes enough to trigger the next cycle of warnings incapacitating the system. Fix it by making console_unlock() insert cond_resched() between lines if @console_may_schedule. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
Calvin Owens <calvinowens@fb.com> Acked-by:
Jan Kara <jack@suse.com> Cc: Dave Jones <davej@codemonkey.org.uk> Cc: Kyle McMartin <kyle@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Hugh Dickins authored
commit 42cb14b1 upstream. clear_page_dirty_for_io() has accumulated writeback and memcg subtleties since v2.6.16 first introduced page migration; and the set_page_dirty() which completed its migration of PageDirty, later had to be moderated to __set_page_dirty_nobuffers(); then PageSwapBacked had to skip that too. No actual problems seen with this procedure recently, but if you look into what the clear_page_dirty_for_io(page)+set_page_dirty(newpage) is actually achieving, it turns out to be nothing more than moving the PageDirty flag, and its NR_FILE_DIRTY stat from one zone to another. It would be good to avoid a pile of irrelevant decrementations and incrementations, and improper event counting, and unnecessary descent of the radix_tree under tree_lock (to set the PAGECACHE_TAG_DIRTY which radix_tree_replace_slot() left in place anyway). Do the NR_FILE_DIRTY movement, like the other stats movements, while interrupts still disabled in migrate_page_move_mapping(); and don't even bother if the zone is the same. Do the PageDirty movement there under tree_lock too, where old page is frozen and newpage not yet visible: bearing in mind that as soon as newpage becomes visible in radix_tree, an un-page-locked set_page_dirty() might interfere (or perhaps that's just not possible: anything doing so should already hold an additional reference to the old page, preventing its migration; but play safe). But we do still need to transfer PageDirty in migrate_page_copy(), for those who don't go the mapping route through migrate_page_move_mapping(). Signed-off-by:
Hugh Dickins <hughd@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Rik van Riel <riel@redhat.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by:
-
Alan Stern authored
commit e50293ef upstream. Commit 8520f380 ("USB: change hub initialization sleeps to delayed_work") changed the hub_activate() routine to make part of it run in a workqueue. However, the commit failed to take a reference to the usb_hub structure or to lock the hub interface while doing so. As a result, if a hub is plugged in and quickly unplugged before the work routine can run, the routine will try to access memory that has been deallocated. Or, if the hub is unplugged while the routine is running, the memory may be deallocated while it is in active use. This patch fixes the problem by taking a reference to the usb_hub at the start of hub_activate() and releasing it at the end (when the work is finished), and by locking the hub interface while the work routine is running. It also adds a check at the start of the routine to see if the hub has already been disconnected, in which nothing should be done. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Alexandru Cornea <alexandru.cornea@intel.com> Tested-by:
-
- 10 Aug, 2016 22 commits
-
-
Greg Kroah-Hartman authored
-
Dmitri Epshtein authored
commit 06708f81 upstream. Commit aebea2ba ("net: mvneta: fix Tx interrupt delay") intended to set coalescing threshold to a value guaranteeing interrupt generation per each sent packet, so that buffers can be released with no delay. In fact setting threshold to '1' was wrong, because it causes interrupt every two packets. According to the documentation a reason behind it is following - interrupt occurs once sent buffers counter reaches a value, which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This behavior was confirmed during tests. Also when testing the SoC working as a NAS device, better performance was observed with int-per-packet, as it strongly depends on the fact that all transmitted packets are released immediately. This commit enables NETA controller work in interrupt per sent packet mode by setting coalescing threshold to 0. Signed-off-by:
Dmitri Epshtein <dima@marvell.com> Signed-off-by:
Marcin Wojtas <mw@semihalf.com> Fixes aebea2ba ("net: mvneta: fix Tx interrupt delay") Acked-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
-
Ilya Dryomov authored
commit 930c5328 upstream. Currently, osd_weight and osd_state fields are updated in the encoding order. This is wrong, because an incremental map may look like e.g. new_up_client: { osd=6, addr=... } # set osd_state and addr new_state: { osd=6, xorstate=EXISTS } # clear osd_state Suppose osd6's current osd_state is EXISTS (i.e. osd6 is down). After applying new_up_client, osd_state is changed to EXISTS | UP. Carrying on with the new_state update, we flip EXISTS and leave osd6 in a weird "!EXISTS but UP" state. A non-existent OSD is considered down by the mapping code 2087 for (i = 0; i < pg->pg_temp.len; i++) { 2088 if (ceph_osd_is_down(osdmap, pg->pg_temp.osds[i])) { 2089 if (ceph_can_shift_osds(pi)) 2090 continue; 2091 2092 temp->osds[temp->size++] = CRUSH_ITEM_NONE; and so requests get directed to the second OSD in the set instead of the first, resulting in OSD-side errors like: [WRN] : client.4239 192.168.122.21:0/2444980242 misdirected client.4239.1:2827 pg 2.5df899f2 to osd.4 not [1,4,6] in e680/680 and hung rbds on the client: [ 493.566367] rbd: rbd0: write 400000 at 11cc00000 (0) [ 493.566805] rbd: rbd0: result -6 xferred 400000 [ 493.567011] blk_update_request: I/O error, dev rbd0, sector 9330688 The fix is to decouple application from the decoding and: - apply new_weight first - apply new_state before new_up_client - twiddle osd_state flags if marking in - clear out some of the state if osd is destroyed Fixes: http://tracker.ceph.com/issues/14901Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Josh Durgin <jdurgin@redhat.com> [idryomov@gmail.com: backport to 3.10-3.14: strip primary-affinity] Signed-off-by:
-
Brian King authored
commit 54e430bb upstream. If we fall back to using LSI on the Croc or Crocodile chip we need to clear the interrupt so we don't hang the system. Tested-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Oliver Hartkopp authored
commit 25e1ed6e upstream. For 'real' hardware CAN devices the netlink interface is used to set CAN specific communication parameters. Real CAN hardware can not be created nor removed with the ip tool ... This patch adds a private dellink function for the CAN device driver interface that does just nothing. It's a follow up to commit 993e6f2f ("can: fix oops caused by wrong rtnl newlink usage") but for dellink. Reported-by:
ajneu <ajneu1@gmail.com> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Oliver Hartkopp authored
commit bce271f2 upstream. With upstream commit bb208f14 (can: fix handling of unmodifiable configuration options) a new can_validate() function was introduced. When invoking 'ip link set can0 type can' without any configuration data can_validate() tries to validate the content without taking into account that there's totally no content. This patch adds a check for missing content. Reported-by:
-
Wolfgang Grandegger authored
commit 43200a44 upstream. At high bus load it could happen that "at91_poll()" enters with all RX message boxes filled up. If then at the end the "quota" is exceeded as well, "rx_next" will not be reset to the first RX mailbox and hence the interrupts remain disabled. Signed-off-by:
Wolfgang Grandegger <wg@grandegger.com> Tested-by:
Amr Bekhit <amrbekhit@gmail.com> Signed-off-by:
-
Taras Kondratiuk authored
commit f68381a7 upstream. The code that fills packed command header assumes that CPU runs in little-endian mode. Hence the header is malformed in big-endian mode and causes MMC data transfer errors: [ 563.200828] mmcblk0: error -110 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc40 [ 563.219647] mmcblk0: packed cmd failed, nr 2, sectors 16, failure index: -1 Convert header data to LE. Signed-off-by:
Taras Kondratiuk <takondra@cisco.com> Fixes: ce39f9d1 ("mmc: support packed write command for eMMC4.5 devices") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Ursula Braun authored
commit 7831b4ff upstream. A qeth_card contains a napi_struct linked to the net_device during device probing. This struct must be deleted when removing the qeth device, otherwise Panic on oops can occur when qeth devices are repeatedly removed and added. Fixes: a1c3ed4c ("qeth: NAPI support for l2 and l3 discipline") Signed-off-by:
Ursula Braun <ubraun@linux.vnet.ibm.com> Tested-by:
Alexander Klein <ALKL@de.ibm.com> Signed-off-by:
-
Vegard Nossum authored
commit 7bc94916 upstream. Although the extent tree depth of 5 should enough be for the worst case of 2*32 extents of length 1, the extent tree code does not currently to merge nodes which are less than half-full with a sibling node, or to shrink the tree depth if possible. So it's possible, at least in theory, for the tree depth to be greater than 5. However, even in the worst case, a tree depth of 32 is highly unlikely, and if the file system is maliciously corrupted, an insanely large eh_depth can cause memory allocation failures that will trigger kernel warnings (here, eh_depth = 65280): JBD2: ext4.exe wants too many credits credits:195849 rsv_credits:0 max:256 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 50 at fs/jbd2/transaction.c:293 start_this_handle+0x569/0x580 CPU: 0 PID: 50 Comm: ext4.exe Not tainted 4.7.0-rc5+ #508 Stack: 604a8947 625badd8 0002fd09 00000000 60078643 00000000 62623910 601bf9bc 62623970 6002fc84 626239b0 900000125 Call Trace: [<6001c2dc>] show_stack+0xdc/0x1a0 [<601bf9bc>] dump_stack+0x2a/0x2e [<6002fc84>] __warn+0x114/0x140 [<6002fdff>] warn_slowpath_null+0x1f/0x30 [<60165829>] start_this_handle+0x569/0x580 [<60165d4e>] jbd2__journal_start+0x11e/0x220 [<60146690>] __ext4_journal_start_sb+0x60/0xa0 [<60120a81>] ext4_truncate+0x131/0x3a0 [<60123677>] ext4_setattr+0x757/0x840 [<600d5d0f>] notify_change+0x16f/0x2a0 [<600b2b16>] do_truncate+0x76/0xc0 [<600c3e56>] path_openat+0x806/0x1300 [<600c55c9>] do_filp_open+0x89/0xf0 [<600b4074>] do_sys_open+0x134/0x1e0 [<600b4140>] SyS_open+0x20/0x30 [<6001ea68>] handle_syscall+0x88/0x90 [<600295fd>] userspace+0x3fd/0x500 [<6001ac55>] fork_handler+0x85/0x90 ---[ end trace 08b0b88b6387a244 ]--- [ Commit message modified and the extent tree depath check changed from 5 to 32 -- tytso ] Cc: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by:
-
Vineet Gupta authored
commit a6416f57 upstream. ARCompact and ARCv2 only have ASL, while binutils used to support LSL as a alias mnemonic. Newer binutils (upstream) don't want to do that so replace it. Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Jeff Mahoney authored
commit f0fe970d upstream. There are legitimate reasons to disallow mmap on certain files, notably in sysfs or procfs. We shouldn't emulate mmap support on file systems that don't offer support natively. CVE-2016-1583 Signed-off-by:
Jeff Mahoney <jeffm@suse.com> [tyhicks: clean up f_op check by using ecryptfs_file_to_lower()] Signed-off-by:
Tyler Hicks <tyhicks@canonical.com> Signed-off-by:
-
Jeff Mahoney authored
commit 78c4e172 upstream. This reverts commit 2f36db71. It fixed a local root exploit but also introduced a dependency on the lower file system implementing an mmap operation just to open a file, which is a bit of a heavy hammer. The right fix is to have mmap depend on the existence of the mmap handler instead. Signed-off-by:
-
Tony Lindgren authored
commit 0ac3c0a4 upstream. With many repeated suspend resume cycles, the pin specific wakeirq may not always work on omaps. This is because the write to enable the pin interrupt may not have reached the device over the interconnect before suspend happens. Let's fix the issue with a flush of posted write with a readback. Reported-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Cameron Gutman authored
commit caca925f upstream. This prevents a malicious USB device from causing an oops. Signed-off-by:
Cameron Gutman <aicommander@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Ping Cheng authored
commit 12afb344 upstream. Somehow the patch that added two-finger touch support forgot to update W8001_MAX_LENGTH from 11 to 13. Signed-off-by:
Ping Cheng <pingc@wacom.com> Reviewed-by:
Peter Hutterer <peter.hutterer@who-t.net> Signed-off-by:
-
Kangjie Lu authored
commit e4ec8cc8 upstream. The stack object “r1” has a total size of 32 bytes. Its field “event” and “val” both contain 4 bytes padding. These 8 bytes padding bytes are sent to user without being initialized. Signed-off-by:
Kangjie Lu <kjlu@gatech.edu> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Kangjie Lu authored
commit 9a47e9cf upstream. The stack object “r1” has a total size of 32 bytes. Its field “event” and “val” both contain 4 bytes padding. These 8 bytes padding bytes are sent to user without being initialized. Signed-off-by:
-
Kangjie Lu authored
commit cec8f96e upstream. The stack object “tread” has a total size of 32 bytes. Its field “event” and “val” both contain 4 bytes padding. These 8 bytes padding bytes are sent to user without being initialized. Signed-off-by:
-
Andrey Grodzovsky authored
commit 02ef871e upstream. Current overlap check is evaluating to false a case where a filter field is fully contained (proper subset) of a r/w request. This change applies classical overlap check instead to include all the scenarios. More specifically, for (Hilscher GmbH CIFX 50E-DP(M/S)) device driver the logic is such that the entire confspace is read and written in 4 byte chunks. In this case as an example, CACHE_LINE_SIZE, LATENCY_TIMER and PCI_BIST are arriving together in one call to xen_pcibk_config_write() with offset == 0xc and size == 4. With the exsisting overlap check the LATENCY_TIMER field (offset == 0xd, length == 1) is fully contained in the write request and hence is excluded from write, which is incorrect. Signed-off-by:
Andrey Grodzovsky <andrey2805@gmail.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by:
Jan Beulich <JBeulich@suse.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Alexey Brodkin authored
commit 9bd54517 upstream. If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core() gets called following message gets printed in debug console: ----------------->8--------------- CONFIG_ARC_DW2_UNWIND needs to be enabled ----------------->8--------------- That message makes sense if user indeed wants to see a backtrace or get nice function call-graphs in perf but what if user disabled unwinder for the purpose? Why pollute his debug console? So instead we'll warn user about possibly missing feature once and let him decide if that was what he or she really wanted. Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by:
-
Torsten Hilbrich authored
commit 63d2f95d upstream. The value `bytes' comes from the filesystem which is about to be mounted. We cannot trust that the value is always in the range we expect it to be. Check its value before using it to calculate the length for the crc32_le call. It value must be larger (or equal) sumoff + 4. This fixes a kernel bug when accidentially mounting an image file which had the nilfs2 magic value 0x3434 at the right offset 0x406 by chance. The bytes 0x01 0x00 were stored at 0x408 and were interpreted as a s_bytes value of 1. This caused an underflow when substracting sumoff + 4 (20) in the call to crc32_le. BUG: unable to handle kernel paging request at ffff88021e600000 IP: crc32_le+0x36/0x100 ... Call Trace: nilfs_valid_sb.part.5+0x52/0x60 [nilfs2] nilfs_load_super_block+0x142/0x300 [nilfs2] init_nilfs+0x60/0x390 [nilfs2] nilfs_mount+0x302/0x520 [nilfs2] mount_fs+0x38/0x160 vfs_kern_mount+0x67/0x110 do_mount+0x269/0xe00 SyS_mount+0x9f/0x100 entry_SYSCALL_64_fastpath+0x16/0x71 Link: http://lkml.kernel.org/r/1466778587-5184-2-git-send-email-konishi.ryusuke@lab.ntt.co.jpSigned-off-by:
Torsten Hilbrich <torsten.hilbrich@secunet.com> Tested-by:
Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by:
-
- 27 Jul, 2016 4 commits
-
-
Greg Kroah-Hartman authored
-
Jan Willeke authored
commit dc295880 upstream. The syscall_set_return_value function of s390 negates the error argument before storing the value to the return register gpr2. This is incorrect, the seccomp code already passes the negative error value. Store the unmodified error value to gpr2. Signed-off-by:
Jan Willeke <willeke@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Hugh Dickins authored
commit 7f556567 upstream. The well-spotted fallocate undo fix is good in most cases, but not when fallocate failed on the very first page. index 0 then passes lend -1 to shmem_undo_range(), and that has two bad effects: (a) that it will undo every fallocation throughout the file, unrestricted by the current range; but more importantly (b) it can cause the undo to hang, because lend -1 is treated as truncation, which makes it keep on retrying until every page has gone, but those already fully instantiated will never go away. Big thank you to xfstests generic/269 which demonstrates this. Fixes: b9b4bb26 ("tmpfs: don't undo fallocate past its last page") Signed-off-by:
-
Anthony Romano authored
commit b9b4bb26 upstream. When fallocate is interrupted it will undo a range that extends one byte past its range of allocated pages. This can corrupt an in-use page by zeroing out its first byte. Instead, undo using the inclusive byte range. Fixes: 1635f6a7 ("tmpfs: undo fallocation on failure") Link: http://lkml.kernel.org/r/1462713387-16724-1-git-send-email-anthony.romano@coreos.comSigned-off-by:
Anthony Romano <anthony.romano@coreos.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Brandon Philips <brandon@ifup.co> Cc: <stable@vger.kernel.org> Signed-off-by:
-
