- 22 Jun, 2015 20 commits
-
-
James Hogan authored
commit 5f35b9cd upstream. Commit 334c86c4 ("MIPS: IRQ: Add stackoverflow detection") added kernel stack overflow detection, however it only enabled it conditional upon the preprocessor definition DEBUG_STACKOVERFLOW, which is never actually defined. The Kconfig option is called DEBUG_STACKOVERFLOW, which manifests to the preprocessor as CONFIG_DEBUG_STACKOVERFLOW, so switch it to using that definition instead. Fixes: 334c86c4 ("MIPS: IRQ: Add stackoverflow detection") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Adam Jiang <jiang.adam@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: http://patchwork.linux-mips.org/patch/10531/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Wang Long authored
commit 10802932 upstream. The producer should be used producer_fifo as its sched_priority, so correct it. Link: http://lkml.kernel.org/r/1433923957-67842-1-git-send-email-long.wanglong@huawei.comSigned-off-by:
Wang Long <long.wanglong@huawei.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Patrick Riphagen authored
commit 1df5b888 upstream. This adds support for new Xsens device, Motion Tracker Development Board, using Xsens' own Vendor ID Signed-off-by:
Patrick Riphagen <patrick.riphagen@xsens.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
John D. Blair authored
commit df72d588 upstream. Added the USB serial device ID for the HubZ dual ZigBee and Z-Wave radio dongle. Signed-off-by:
John D. Blair <johnb@candicontrols.com> Signed-off-by:
-
Dan Williams authored
commit 4d66e5e9 upstream. ================================= [ INFO: inconsistent lock state ] 4.1.0-rc7+ #217 Tainted: G O --------------------------------- inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. swapper/6/0 [HC0[0]:SC1[1]:HE1:SE0] takes: (ext_devt_lock){+.?...}, at: [<ffffffff8143a60c>] blk_free_devt+0x3c/0x70 {SOFTIRQ-ON-W} state was registered at: [<ffffffff810bf6b1>] __lock_acquire+0x461/0x1e70 [<ffffffff810c1947>] lock_acquire+0xb7/0x290 [<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50 [<ffffffff8143a07d>] blk_alloc_devt+0x6d/0xd0 <-- take the lock in process context [..] [<ffffffff810bf64e>] __lock_acquire+0x3fe/0x1e70 [<ffffffff810c00ad>] ? __lock_acquire+0xe5d/0x1e70 [<ffffffff810c1947>] lock_acquire+0xb7/0x290 [<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70 [<ffffffff818ac3a8>] _raw_spin_lock+0x38/0x50 [<ffffffff8143a60c>] ? blk_free_devt+0x3c/0x70 [<ffffffff8143a60c>] blk_free_devt+0x3c/0x70 <-- take the lock in softirq [<ffffffff8143bfec>] part_release+0x1c/0x50 [<ffffffff8158edf6>] device_release+0x36/0xb0 [<ffffffff8145ac2b>] kobject_cleanup+0x7b/0x1a0 [<ffffffff8145aad0>] kobject_put+0x30/0x70 [<ffffffff8158f147>] put_device+0x17/0x20 [<ffffffff8143c29c>] delete_partition_rcu_cb+0x16c/0x180 [<ffffffff8143c130>] ? read_dev_sector+0xa0/0xa0 [<ffffffff810e0e0f>] rcu_process_callbacks+0x2ff/0xa90 [<ffffffff810e0dcf>] ? rcu_process_callbacks+0x2bf/0xa90 [<ffffffff81067e2e>] __do_softirq+0xde/0x600 Neil sees this in his tests and it also triggers on pmem driver unbind for the libnvdimm tests. This fix is on top of an initial fix by Keith for incorrect usage of mutex_lock() in this path: 2da78092 "block: Fix dev_t minor allocation lifetime". Both this and 2da78092 are candidates for -stable. Fixes: 2da78092 ("block: Fix dev_t minor allocation lifetime") Cc: Keith Busch <keith.busch@intel.com> Reported-by:
NeilBrown <neilb@suse.de> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Hans de Goede authored
commit 5f0ee9d1 upstream. Make the check to skip the rate check more lax, so that it applies to all hw_version 4 models. This fixes the touchpad not being detected properly on Asus PU551LA laptops. Reported-and-tested-by:
David Zafra Gómez <dezeta@klo.es> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Clemens Ladisch authored
commit 044bddb9 upstream. Add mixer control names for the ESI Maya44 USB+ (which appears to be identical width the AudioTrak Maya44 USB). Reported-by:
nightmixes <nightmixes@gmail.com> Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Wolfram Sang authored
commit 1ef9f058 upstream. Fix this from the logs: usb 7-1: New USB device found, idVendor=046d, idProduct=08ca ... usb 7-1: Warning! Unlikely big volume range (=3072), cval->res is probably wrong. usb 7-1: [5] FU [Mic Capture Volume] ch = 1, val = 4608/7680/1 Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Takashi Iwai authored
commit b5d724b1 upstream. Acer Aspire 9420 with ALC883 (1025:0107) needs the fixup for EAPD to make the sound working like other Aspire models. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94111Signed-off-by:
-
Paul Cercueil authored
commit c2a8b623 upstream. We unfortunately can't use ~0UL for the scan mask to indicate that the only valid scan mask is all channels selected. The IIO core needs the exact mask to work correctly and not a super-set of it. So calculate the masked based on the channels that are available for a particular device. Signed-off-by:
Paul Cercueil <paul.cercueil@analog.com> Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Fixes: 5eda3550 ("staging:iio:adis16400: Preallocate transfer message") Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Paul Cercueil authored
commit 7323d598 upstream. Previously, the two voltage channels had the same ID, which didn't cause conflicts in sysfs only because one channel is named and the other isn't; this is still violating the spec though, two indexed channels should never have the same index. Signed-off-by:
-
Lars-Peter Clausen authored
commit 69ca2d77 upstream. Add the scale for the pressure channel, which is currently missing. Signed-off-by:
-
Ian Campbell authored
[ Upstream commit 31a41898 ] When we come to tear things down in netback_remove() and generate the uevent it is possible that the xenstore directory has already been removed (details below). In such cases netback_uevent() won't be able to read the hotplug script and will write a xenstore error node. A recent change to the hypervisor exposed this race such that we now sometimes lose it (where apparently we didn't ever before). Instead read the hotplug script configuration during setup and use it for the lifetime of the backend device. The apparently more obvious fix of moving the transition to state=Closed in netback_remove() to after the uevent does not work because it is possible that we are already in state=Closed (in reaction to the guest having disconnected as it shutdown). Being already in Closed means the toolstack is at liberty to start tearing down the xenstore directories. In principal it might be possible to arrange to unregister the device sooner (e.g on transition to Closing) such that xenstore would still be there but this state machine is fragile and prone to anger... A modern Xen system only relies on the hotplug uevent for driver domains, when the backend is in the same domain as the toolstack it will run the necessary setup/teardown directly in the correct sequence wrt xenstore changes. Signed-off-by:
Ian Campbell <ian.campbell@citrix.com> Acked-by:
Wei Liu <wei.liu2@citrix.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit beb39db5 ] We have two problems in UDP stack related to bogus checksums : 1) We return -EAGAIN to application even if receive queue is not empty. This breaks applications using edge trigger epoll() 2) Under UDP flood, we can loop forever without yielding to other processes, potentially hanging the host, especially on non SMP. This patch is an attempt to make things better. We might in the future add extra support for rt applications wanting to better control time spent doing a recv() in a hostile environment. For example we could validate checksums before queuing packets in socket receive queue. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by:
-
WANG Cong authored
[ Upstream commit 86e363dc ] For mq qdisc, we add per tx queue qdisc to root qdisc for display purpose, however, that happens too early, before the new dev->qdisc is finally set, this causes q->list points to an old root qdisc which is going to be freed right before assigning with a new one. Fix this by moving ->attach() after setting dev->qdisc. For the record, this fixes the following crash: ------------[ cut here ]------------ WARNING: CPU: 1 PID: 975 at lib/list_debug.c:59 __list_del_entry+0x5a/0x98() list_del corruption. prev->next should be ffff8800d1998ae8, but was 6b6b6b6b6b6b6b6b CPU: 1 PID: 975 Comm: tc Not tainted 4.1.0-rc4+ #1019 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 0000000000000009 ffff8800d73fb928 ffffffff81a44e7f 0000000047574756 ffff8800d73fb978 ffff8800d73fb968 ffffffff810790da ffff8800cfc4cd20 ffffffff814e725b ffff8800d1998ae8 ffffffff82381250 0000000000000000 Call Trace: [<ffffffff81a44e7f>] dump_stack+0x4c/0x65 [<ffffffff810790da>] warn_slowpath_common+0x9c/0xb6 [<ffffffff814e725b>] ? __list_del_entry+0x5a/0x98 [<ffffffff81079162>] warn_slowpath_fmt+0x46/0x48 [<ffffffff81820eb0>] ? dev_graft_qdisc+0x5e/0x6a [<ffffffff814e725b>] __list_del_entry+0x5a/0x98 [<ffffffff814e72a7>] list_del+0xe/0x2d [<ffffffff81822f05>] qdisc_list_del+0x1e/0x20 [<ffffffff81820cd1>] qdisc_destroy+0x30/0xd6 [<ffffffff81822676>] qdisc_graft+0x11d/0x243 [<ffffffff818233c1>] tc_get_qdisc+0x1a6/0x1d4 [<ffffffff810b5eaf>] ? mark_lock+0x2e/0x226 [<ffffffff817ff8f5>] rtnetlink_rcv_msg+0x181/0x194 [<ffffffff817ff72e>] ? rtnl_lock+0x17/0x19 [<ffffffff817ff72e>] ? rtnl_lock+0x17/0x19 [<ffffffff817ff774>] ? __rtnl_unlock+0x17/0x17 [<ffffffff81855dc6>] netlink_rcv_skb+0x4d/0x93 [<ffffffff817ff756>] rtnetlink_rcv+0x26/0x2d [<ffffffff818544b2>] netlink_unicast+0xcb/0x150 [<ffffffff81161db9>] ? might_fault+0x59/0xa9 [<ffffffff81854f78>] netlink_sendmsg+0x4fa/0x51c [<ffffffff817d6e09>] sock_sendmsg_nosec+0x12/0x1d [<ffffffff817d8967>] sock_sendmsg+0x29/0x2e [<ffffffff817d8cf3>] ___sys_sendmsg+0x1b4/0x23a [<ffffffff8100a1b8>] ? native_sched_clock+0x35/0x37 [<ffffffff810a1d83>] ? sched_clock_local+0x12/0x72 [<ffffffff810a1fd4>] ? sched_clock_cpu+0x9e/0xb7 [<ffffffff810def2a>] ? current_kernel_time+0xe/0x32 [<ffffffff810b4bc5>] ? lock_release_holdtime.part.29+0x71/0x7f [<ffffffff810ddebf>] ? read_seqcount_begin.constprop.27+0x5f/0x76 [<ffffffff810b6292>] ? trace_hardirqs_on_caller+0x17d/0x199 [<ffffffff811b14d5>] ? __fget_light+0x50/0x78 [<ffffffff817d9808>] __sys_sendmsg+0x42/0x60 [<ffffffff817d9838>] SyS_sendmsg+0x12/0x1c [<ffffffff81a50e97>] system_call_fastpath+0x12/0x6f ---[ end trace ef29d3fb28e97ae7 ]--- For long term, we probably need to clean up the qdisc_graft() code in case it hides other bugs like this. Fixes: 95dc1929 ("pkt_sched: give visibility to mq slave qdiscs") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
-
Mark Salyzyn authored
[ Upstream commit b48732e4 ] got a rare NULL pointer dereference in clear_bit Signed-off-by:
Mark Salyzyn <salyzyn@android.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> ---- v2: switch to sock_flag(sk, SOCK_DEAD) and added net/caif/caif_socket.c v3: return -ECONNRESET in upstream caller of wait function for SOCK_DEAD Signed-off-by:
-
Richard Cochran authored
[ Upstream commit 397a253a ] Currently, the calibration function that corrects the initial offsets among multiple devices only works the first time. If the function is called more than once, the calibration fails and bogus offsets will be programmed into the devices. In a well hidden spot, the device documentation tells that trigger indexes 0 and 1 are special in allowing the TRIG_IF_LATE flag to actually work. This patch fixes the issue by using one of the special triggers during the recalibration method. Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Thadeu Lima de Souza Cascardo authored
[ Upstream commit 47cc84ce ] When more than a multicast address is present in a MLDv2 report, all but the first address is ignored, because the code breaks out of the loop if there has not been an error adding that address. This has caused failures when two guests connected through the bridge tried to communicate using IPv6. Neighbor discoveries would not be transmitted to the other guest when both used a link-local address and a static address. This only happens when there is a MLDv2 querier in the network. The fix will only break out of the loop when there is a failure adding a multicast address. The mdb before the patch: dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp dev ovirtmgmt port bond0.86 grp ff02::2 temp After the patch: dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp dev ovirtmgmt port bond0.86 grp ff02::fb temp dev ovirtmgmt port bond0.86 grp ff02::2 temp dev ovirtmgmt port bond0.86 grp ff02::d temp dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp dev ovirtmgmt port bond0.86 grp ff02::16 temp dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp Fixes: 08b202b6 ("bridge br_multicast: IPv6 MLD support.") Reported-by:
Rik Theys <Rik.Theys@esat.kuleuven.be> Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Tested-by:
-
Eric W. Biederman authored
[ Upstream commit 381c759d ] ip_error does not check if in_dev is NULL before dereferencing it. IThe following sequence of calls is possible: CPU A CPU B ip_rcv_finish ip_route_input_noref() ip_route_input_slow() inetdev_destroy() dst_input() With the result that a network device can be destroyed while processing an input packet. A crash was triggered with only unicast packets in flight, and forwarding enabled on the only network device. The error condition was created by the removal of the network device. As such it is likely the that error code was -EHOSTUNREACH, and the action taken by ip_error (if in_dev had been accessible) would have been to not increment any counters and to have tried and likely failed to send an icmp error as the network device is going away. Therefore handle this weird case by just dropping the packet if !in_dev. It will result in dropping the packet sooner, and will not result in an actual change of behavior. Fixes: 251da413 ("ipv4: Cache ip_error() routes even when not forwarding.") Reported-by:
Vittorio Gambaletta <linuxbugs@vittgam.net> Tested-by:
"Eric W. Biederman" <ebiederm@xmission.com> Acked-by:
-
Florian Fainelli authored
[ Upstream commit 7e140696 ] RGMII interfaces come in multiple flavors: RGMII with transmit or receive internal delay, no delays at all, or delays in both direction. This change extends the initial check for PHY_INTERFACE_MODE_RGMII to cover all of these variants since EEE should be allowed for any of these modes, since it is a property of the RGMII, hence Gigabit PHY capability more than the RGMII electrical interface and its delays. Fixes: a59a4d19 ("phy: add the EEE support and the way to access to the MMD registers") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
- 06 Jun, 2015 20 commits
-
-
Greg Kroah-Hartman authored
-
Andrew Morton authored
commit 2b1d3ae9 upstream. load_elf_binary() returns `retval', not `error'. Fixes: a87938b2 ("fs/binfmt_elf.c: fix bug in loading of PIE binaries") Reported-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Sasha Levin authored
commit 161f873b upstream. We used to read file_handle twice. Once to get the amount of extra bytes, and once to fetch the entire structure. This may be problematic since we do size verifications only after the first read, so if the number of extra bytes changes in userspace between the first and second calls, we'll have an incoherent view of file_handle. Instead, read the constant size once, and copy that over to the final structure without having to re-read it again. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Rafael J. Wysocki authored
commit b9a5e5e1 upstream. Since acpi_reserve_resources() is defined as a device_initcall(), there's no guarantee that it will be executed in the right order with respect to the rest of the ACPI initialization code. On some systems this leads to breakage if, for example, the address range that should be reserved for the ACPI fixed registers is given to the PCI host bridge instead if the race is won by the wrong code path. Fix this by turning acpi_reserve_resources() into a void function and calling it directly from within the ACPI initialization sequence. Reported-and-tested-by:
George McCollister <george.mccollister@gmail.com> Link: http://marc.info/?t=143092384600002&r=1&w=2Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Benjamin Tissoires authored
commit 3c0213d1 upstream. When the v3 hardware sees more than one finger, it uses the semi-mt protocol to report the touches. However, it currently works when num_fingers is 0, 1 or 2, but when it is 3 and above, it sends only 1 finger as if num_fingers was 1. This confuses userspace which knows how to deal with extra fingers when all the slots are used, but not when some are missing. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=90101Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
-
Larry Finger authored
commit 414b7e3b upstream. The USB mini-driver in rtlwifi, which is used by rtl8192cu, issues a call to usb_control_msg() with a timeout value of 0. In some instances where the interface is shutting down, this infinite wait results in a CPU deadlock. A one second timeout fixes this problem without affecting any normal operations. This bug is reported at https://bugzilla.novell.com/show_bug.cgi?id=927786. Reported-by:
Bernhard Wiedemann <bwiedemann@suse.com> Tested-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Bernhard Wiedemann <bwiedemann@suse.com> Cc: Takashi Iwai<tiwai@suse.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
NeilBrown authored
commit 6e9eac2d upstream. If any memory allocation in resize_stripes fails we will return -ENOMEM, but in some cases we update conf->pool_size anyway. This means that if we try again, the allocations will be assumed to be larger than they are, and badness results. So only update pool_size if there is no error. This bug was introduced in 2.6.17 and the patch is suitable for -stable. Fixes: ad01c9e3 ("[PATCH] md: Allow stripes to be expanded in preparation for expanding an array") Signed-off-by:
-
Scott Mayhew authored
commit 9507271d upstream. In an environment where the KDC is running Active Directory, the exported composite name field returned in the context could be large enough to span a page boundary. Attaching a scratch buffer to the decoding xdr_stream helps deal with those cases. The case where we saw this was actually due to behavior that's been fixed in newer gss-proxy versions, but we're fixing it here too. Signed-off-by:
Scott Mayhew <smayhew@redhat.com> Reviewed-by:
Simo Sorce <simo@redhat.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Russell King authored
commit 1b979372 upstream. Josh Stone reports: I've discovered a case where both arm and arm64 will miss a ptrace syscall-exit that they should report. If the syscall is entered without TIF_SYSCALL_TRACE set, then it goes on the fast path. It's then possible to have TIF_SYSCALL_TRACE added in the middle of the syscall, but ret_fast_syscall doesn't check this flag again. Fix this by always checking for a syscall trace in the fast exit path. Reported-by:
Josh Stone <jistone@redhat.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Philippe Reynes authored
commit a29ef819 upstream. According to the imx27 documentation, fec has a 4 Kbyte memory space map. Moreover, the actual 16 Kbyte mapping overlaps the SCC (Security Controller) memory register space. So, we reduce the memory register space to 4 Kbyte. Signed-off-by:
Philippe Reynes <tremyfr@gmail.com> Acked-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Fixes: 9f0749e3 ("ARM i.MX27: Add devicetree support") Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Harald Freudenberger authored
commit a1cae34e upstream. Multitheaded tests showed that the icv buffer in the current ghash implementation is not handled correctly. A move of this working ghash buffer value to the descriptor context fixed this. Code is tested and verified with an multithreaded application via af_alg interface. Signed-off-by:
Harald Freudenberger <freude@linux.vnet.ibm.com> Signed-off-by:
Gerald Schaefer <geraldsc@linux.vnet.ibm.com> Reported-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Scott Branden authored
commit ea345c14 upstream. Add the USB Id to link the D-Link DWA 130 USB Wifi adapter to the rt2830 driver. Signed-off-by:
Scott Branden <sbranden@broadcom.com> Signed-off-by:
Pieter Truter <ptruter@broadcom.com> Signed-off-by:
-
Gabriele Mazzotta authored
commit 09c5b480 upstream. When the LPM policy is set to ATA_LPM_MAX_POWER, the device might generate a spurious PHY event that cuases errors on the link. Ignore this event if it occured within 10s after the policy change. The timeout was chosen observing that on a Dell XPS13 9333 these spurious events can occur up to roughly 6s after the policy change. Link: http://lkml.kernel.org/g/3352987.ugV1Ipy7Z5@xps13Signed-off-by:
Gabriele Mazzotta <gabriele.mzt@gmail.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Gabriele Mazzotta authored
commit 8393b811 upstream. This is a preparation commit that will allow to add other criteria according to which PHY events should be dropped. Signed-off-by:
-
Eryu Guan authored
commit 2f974865 upstream. The following commit introduced a bug when checking for zero length extent 5946d089 ext4: check for overlapping extents in ext4_valid_extent_entries() Zero length extent could pass the check if lblock is zero. Adding the explicit check for zero length back. Signed-off-by:
Eryu Guan <guaneryu@gmail.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Dmitry Monakhov authored
commit 7afe5aa5 upstream. Use wait_for_stable_page() instead of wait_on_page_writeback() Signed-off-by:
Dmitry Monakhov <dmonakhov@openvz.org> Signed-off-by:
Jan Kara <jack@suse.cz> Cc: Alex Shi <alex.shi@linaro.org> Signed-off-by:
-
Ludovic Desroches authored
commit 60c8f783 upstream. clkdiv is declared as an u32 but it can be set to a negative value causing a huge divisor value. Change its type to int to avoid this case. Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Anton Blanchard authored
commit 5e95235c upstream. Recent toolchains force the TOC to be 256 byte aligned. We need to enforce this alignment in our linker script, otherwise pointers to our TOC variables (__toc_start, __prom_init_toc_start) could be incorrect. If they are bad, we die a few hundred instructions into boot. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Krzysztof Opasiak authored
commit 903124fe upstream. memset() to 0 interfaces array before reusing usb_configuration structure. This commit fix bug: ln -s functions/acm.1 configs/c.1 ln -s functions/acm.2 configs/c.1 ln -s functions/acm.3 configs/c.1 echo "UDC name" > UDC echo "" > UDC rm configs/c.1/acm.* rmdir functions/* mkdir functions/ecm.usb0 ln -s functions/ecm.usb0 configs/c.1 echo "UDC name" > UDC [ 82.220969] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 82.229009] pgd = c0004000 [ 82.231698] [00000000] *pgd=00000000 [ 82.235260] Internal error: Oops: 17 [#1] PREEMPT SMP ARM [ 82.240638] Modules linked in: [ 82.243681] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.0.0-rc2 #39 [ 82.249926] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) [ 82.256003] task: c07cd2f0 ti: c07c8000 task.ti: c07c8000 [ 82.261393] PC is at composite_setup+0xe3c/0x1674 [ 82.266073] LR is at composite_setup+0xf20/0x1674 [ 82.270760] pc : [<c03510d4>] lr : [<c03511b8>] psr: 600001d3 [ 82.270760] sp : c07c9df0 ip : c0806448 fp : ed8c9c9c [ 82.282216] r10: 00000001 r9 : 00000000 r8 : edaae918 [ 82.287425] r7 : ed551cc0 r6 : 00007fff r5 : 00000000 r4 : ed799634 [ 82.293934] r3 : 00000003 r2 : 00010002 r1 : edaae918 r0 : 0000002e [ 82.300446] Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel [ 82.307910] Control: 10c5387d Table: 6bc1804a DAC: 00000015 [ 82.313638] Process swapper/0 (pid: 0, stack limit = 0xc07c8210) [ 82.319627] Stack: (0xc07c9df0 to 0xc07ca000) [ 82.323969] 9de0: 00000000 c06e65f4 00000000 c07c9f68 [ 82.332130] 9e00: 00000067 c07c59ac 000003f7 edaae918 ed8c9c98 ed799690 eca2f140 200001d3 [ 82.340289] 9e20: ee79a2d8 c07c9e88 c07c5304 ffff55db 00010002 edaae810 edaae860 eda96d50 [ 82.348448] 9e40: 00000009 ee264510 00000007 c07ca444 edaae860 c0340890 c0827a40 ffff55e0 [ 82.356607] 9e60: c0827a40 eda96e40 ee264510 edaae810 00000000 edaae860 00000007 c07ca444 [ 82.364766] 9e80: edaae860 c0354170 c03407dc c033db4c edaae810 00000000 00000000 00000010 [ 82.372925] 9ea0: 00000032 c0341670 00000000 00000000 00000001 eda96e00 00000000 00000000 [ 82.381084] 9ec0: 00000000 00000032 c0803a23 ee1aa840 00000001 c005d54c 249e2450 00000000 [ 82.389244] 9ee0: 200001d3 ee1aa840 ee1aa8a0 ed84f4c0 00000000 c07c9f68 00000067 c07c59ac [ 82.397403] 9f00: 00000000 c005d688 ee1aa840 ee1aa8a0 c07db4b4 c006009c 00000032 00000000 [ 82.405562] 9f20: 00000001 c005ce20 c07c59ac c005cf34 f002000c c07ca780 c07c9f68 00000057 [ 82.413722] 9f40: f0020000 413fc090 00000001 c00086b4 c000f804 60000053 ffffffff c07c9f9c [ 82.421880] 9f60: c0803a20 c0011fc0 00000000 00000000 c07c9fb8 c001bee0 c07ca4f0 c057004c [ 82.430040] 9f80: c07ca4fc c0803a20 c0803a20 413fc090 00000001 00000000 01000000 c07c9fb0 [ 82.438199] 9fa0: c000f800 c000f804 60000053 ffffffff 00000000 c0050e70 c0803bc0 c0783bd8 [ 82.446358] 9fc0: ffffffff ffffffff c0783664 00000000 00000000 c07b13e8 00000000 c0803e54 [ 82.454517] 9fe0: c07ca480 c07b13e4 c07ce40c 4000406a 00000000 40008074 00000000 00000000 [ 82.462689] [<c03510d4>] (composite_setup) from [<c0340890>] (s3c_hsotg_complete_setup+0xb4/0x418) [ 82.471626] [<c0340890>] (s3c_hsotg_complete_setup) from [<c0354170>] (usb_gadget_giveback_request+0xc/0x10) [ 82.481429] [<c0354170>] (usb_gadget_giveback_request) from [<c033db4c>] (s3c_hsotg_complete_request+0xcc/0x12c) [ 82.491583] [<c033db4c>] (s3c_hsotg_complete_request) from [<c0341670>] (s3c_hsotg_irq+0x4fc/0x558) [ 82.500614] [<c0341670>] (s3c_hsotg_irq) from [<c005d54c>] (handle_irq_event_percpu+0x50/0x150) [ 82.509291] [<c005d54c>] (handle_irq_event_percpu) from [<c005d688>] (handle_irq_event+0x3c/0x5c) [ 82.518145] [<c005d688>] (handle_irq_event) from [<c006009c>] (handle_fasteoi_irq+0xd4/0x18c) [ 82.526650] [<c006009c>] (handle_fasteoi_irq) from [<c005ce20>] (generic_handle_irq+0x20/0x30) [ 82.535242] [<c005ce20>] (generic_handle_irq) from [<c005cf34>] (__handle_domain_irq+0x6c/0xdc) [ 82.543923] [<c005cf34>] (__handle_domain_irq) from [<c00086b4>] (gic_handle_irq+0x2c/0x6c) [ 82.552256] [<c00086b4>] (gic_handle_irq) from [<c0011fc0>] (__irq_svc+0x40/0x74) [ 82.559716] Exception stack(0xc07c9f68 to 0xc07c9fb0) [ 82.564753] 9f60: 00000000 00000000 c07c9fb8 c001bee0 c07ca4f0 c057004c [ 82.572913] 9f80: c07ca4fc c0803a20 c0803a20 413fc090 00000001 00000000 01000000 c07c9fb0 [ 82.581069] 9fa0: c000f800 c000f804 60000053 ffffffff [ 82.586113] [<c0011fc0>] (__irq_svc) from [<c000f804>] (arch_cpu_idle+0x30/0x3c) [ 82.593491] [<c000f804>] (arch_cpu_idle) from [<c0050e70>] (cpu_startup_entry+0x128/0x1a4) [ 82.601740] [<c0050e70>] (cpu_startup_entry) from [<c0783bd8>] (start_kernel+0x350/0x3bc) [ 82.609890] Code: 0a000002 e3530005 05975010 15975008 (e5953000) [ 82.615965] ---[ end trace f57d5f599a5f1bfa ]--- Most of kernel code assume that interface array in struct usb_configuration is NULL terminated. When gadget is composed with configfs configuration structure may be reused for different functions set. This bug happens because purge_configs_funcs() sets only next_interface_id to 0. Interface array still contains pointers to already freed interfaces. If in second try we add less interfaces than earlier we may access unallocated memory when trying to get interface descriptors. Signed-off-by:
Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Hans de Goede authored
commit 17211509 upstream. Without this flag some versions of these enclosures do not work. Reported-and-tested-by:
Christian Schaller <cschalle@redhat.com> Signed-off-by:
-
