- 27 Aug, 2015 40 commits
-
-
Sreekanth Reddy authored
mpt3sas: Get IOC_FACTS information using handshake protocol only after HBA card gets into READY or Operational state. Driver initialization fails if driver tries to send IOC facts request message when the IOC is in reset or in a fault state. This patch will make sure that 1.Driver to send IOC facts request message only if HBA is in operational or ready state. 2.If IOC is in fault state, a diagnostic reset would be issued. 3.If IOC is in reset state then driver will wait for 10 seconds to exit out of reset state. If the HBA continues to be in reset state, then the HBA wouldn't be claimed by the driver. Signed-off-by:
Sreekanth Reddy <Sreekanth.Reddy@avagotech.com> Reviewed-by:
Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
James Bottomley <JBottomley@Odin.com>
-
Sreekanth Reddy authored
In this patch, increased the number of MSIX vector support for SAS3 C0 HBAs to up-to 96. Following are changes that are done in this patch 1. This feature is enabled only for SAS3 C0 and higher revision cards and also only when reply post free queue count is greater than 8. 2. To support this feature 12 SupplementalReplyPostHostIndex system interfaces are used. MSI-X index numbered from 0 to 7 use the first SupplementalReplyPostHostIndex system interface to update its corresponding ReplyPostHostIndex values, MSI-X index numbered from 8 to 15 will use the second SupplementalReplyPostHostIndex system interface and so on. These 12 SuppementalReplyPostHostIndex system interfaces address are saved in the array replyPostRegisterIndex[]. 3. As each SupplementalReplyPostHostIndex register supports 8 MSI-X vectors. So MSIxIndex field in these register must contain a value between 0 and 7. 4. After processing the reply descriptors from a reply post free queues then update the new reply post host index value in ReplyPostHostIndex field and (msix_index mod 8) value in MSIxIndex field of SupplementalReplyPostHostIndex register. The Address of this SupplementalReplyPostHostIndex register is retrived from (msix_index/8)th entry of replyPostRegisterIndex[] array. Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
-
Dan Carpenter authored
We recently did some cleanup here and now the static checkers notice that there is a missing error code when ioremap() fails. Let's set it to -ENOMEM. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
-
K. Y. Srinivasan authored
In the function storvsc_channel_init(), error code was not getting set correctly in some of the failure cases. Fix this issue. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Reported-by:
-
Keith Mange authored
Allow WRITE_SAME for Windows10 and above hosts. Tested-by:
Alex Ng <alexng@microsoft.com> Signed-off-by:
Keith Mange <keith.mange@microsoft.com> Signed-off-by:
-
Keith Mange authored
Use storage protocol version instead of vmbus protocol version when determining storage capabilities. Tested-by:
-
Keith Mange authored
Use correct defaults for values determined by protocol negotiation, instead of resetting them with every scsi controller. Tested-by:
-
Keith Mange authored
Currently we are making decisions based on vmbus protocol versions that have been negotiated; use storage potocol versions instead. [jejb: fold ARRAY_SIZE conversion suggested by Johannes Thumshirn <jthumshirn@suse.de> make vmstor_protocol static] Tested-by:
-
Keith Mange authored
Use a single value to track protocol versions to simplify comparisons and to be consistent with vmbus version tracking. Tested-by:
-
Keith Mange authored
Rather than look for sets of specific protocol versions, make decisions based on ranges. This will be safer and require fewer changes going forward as we add more storage protocol versions. Tested-by:
-
Matthew R. Ochs authored
The queuecommand routine has a local dev pointer used for the dev_* prints. The two prints that currently exist are tucked under a debug define and thus can be left out. Use the actual location instead of a local to avoid this warning. This patch is intended to be applied after the "CXL Flash Error Recovery and Superpipe" series. Signed-off-by:
Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by:
Manoj N. Kumar <manoj@linux.vnet.ibm.com> Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
-
Dan Carpenter authored
"port_sel" is a u64 so the shifting should also be a 64 bit shift. Fixes: c21e0bbf ('cxlflash: Base support for IBM CXL Flash Adapter') Signed-off-by:
-
Dan Carpenter authored
The > should be >= or we read one element past the end of the array. Fixes: c21e0bbf ('cxlflash: Base support for IBM CXL Flash Adapter') Signed-off-by:
-
Matthew R. Ochs authored
Add support for physical LUN segmentation (virtual LUNs) to device driver supporting the IBM CXL Flash adapter. This patch allows user space applications to virtually segment a physical LUN into N virtual LUNs, taking advantage of the translation features provided by this adapter. Signed-off-by:
Michael Neuling <mikey@neuling.org> Reviewed-by:
Wen Xiong <wenxiong@linux.vnet.ibm.com> Signed-off-by:
-
Matthew R. Ochs authored
Add superpipe supporting infrastructure to device driver for the IBM CXL Flash adapter. This patch allows userspace applications to take advantage of the accelerated I/O features that this adapter provides and bypass the traditional filesystem stack. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Matthew R. Ochs authored
Introduce support for enhanced I/O error handling. A device state is added to track 3 possible states of the device: Normal - the device is operating normally and is fully operational Limbo - the device is in a reset/recovery scenario and its operational status is paused Failed/terminating - the device has either failed to be reset/recovered or is being terminated (removed); it is no longer operational All operations are allowed when the device is operating normally. When the device transitions to limbo state, I/O must be paused. To help accomplish this, a wait queue is introduced where existing and new threads can wait until the device is no longer in limbo. When coming out of limbo, threads need to check the state and error out gracefully when encountering the failed state. When the device transitions to the failed/terminating state, normal operations are no longer allowed. Only specially designated operations related to graceful cleanup are permitted. Signed-off-by:Daniel Axtens <dja@axtens.net> Reviewed-by:
-
Himanshu Madhani authored
Signed-off-by:
Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
-
Sawan Chandak authored
Signed-off-by:
Sawan Chandak <sawan.chandak@qlogic.com> Signed-off-by:
-
Arun Easi authored
On certain conditions, login failures will just invoke qla2x00_mark_device_lost() with the intend to do login again; but if login_retry has been set already, that would fail to set the relogin needed flag which is required to wakeup the DPC to retry. Signed-off-by:
Arun Easi <arun.easi@qlogic.com> Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
-
Chad Dupuis authored
Fix for memory leak when command is not found by firmware due to mismatch in sp reference count. Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Sawan Chandak authored
Signed-off-by:
-
Chad Dupuis authored
Instead of resetting the adapter wait for the login to timeout and retry. Resetting the adapter can cause extended path recovery times. Signed-off-by:
-
Chad Dupuis authored
If an SRB is NULL but the handle is in range just drop the command instead of also resetting the adapter. If the handle is in range then the command was valid at some point and may have been aborted. Resetting the adapter can lead to extended recovery times in this case. Signed-off-by:
-
Hiral Patel authored
Aovid crashing the system in the scenario where firmware just completes the command and it can not find the command during abort mailbox processing. This scenario can lead to sp reference counter being zero. Instead of crashing the system, use WARN_ON to print warning in log file. Signed-off-by:
Hiral Patel <hiral.patel@qlogic.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
Execute qla25xx_manipulate_risc_semaphore() only for ssdid 0x0175 and 0x0240. Signed-off-by:
-
Joe Carnuccio authored
When we get logged out, mark the port lost and set dpc flag for relogin. Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
jiang.biao2@zte.com.cn authored
scsi_error: should not get sense for timeout IO in scsi error handler When an IO timeout occurs, the IO will be aborted in scsi_abort_command() and SCSI_EH_ABORT_SCHEDULED will be set. Because of that, the SCSI_EH_CANCEL_CMD will be clear in scsi_eh_scmd_add(). So when scsi error handler starts, it will get sense for this timeout IO and the scmd of the IO request will be reused. In that case, the scmd may be double released when racing with io_done(), which will result in crash. SO SCSI_EH_ABORT_SCHEDULED should also be checked when getting sense. The bug maybe reproduced when the link between host and disk is unstable. Signed-off-by:
Jiang Biao <jiang.biao2@zte.com.cn> Signed-off-by:
Long Chun <long.chun@zte.com.cn> Reviewed-by:
Tan Hu <tan.hu@zte.com.cn> Reviewed-by:
Chen Donghai <chen.donghai@zte.com.cn> Reviewed-by:
Cai Qu <cai.qu@zte.com.cn> Signed-off-by:
-
Viswas G authored
Bump pm80xx driver version to 0.1.38. Signed-off-by:
Viswas G <Viswas.G@pmcs.com> Reviewed-by:
Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Reviewed-by:
Jack Wang <jinpu.wang@profitbricks.com> Reviewed-by:
-
Viswas G authored
The request has to be retried incase if the length of the SSP Response IU is invalid. Signed-off-by:
-
Viswas G authored
PORT RECOVERY TIMEOUT is the maximum time between the controller's detection of the PHY down until the receipt of the ID_Frame (from the same remote SAS port). If the time expires before the ID_FRAME is received, the port is considered INVALID and can be removed. The IOP_EVENT_PORT_RECOVERY_TIMER_TMO event is reported following the IOP_EVENT_ PHY_DOWN event when the PHY/port does not recover after Port Recovery Time. Signed-off-by:
-
Viswas G authored
If the link error happens, we don't need to disconnect the phy, which will remove the drive. Instead acknowledging the controller and logging the error will be enough. Signed-off-by:
-
Viswas G authored
In pm8001_ccb_task_free(), the dma unmapping is done based on ccb->n_elem value. This should be initialized to zero in the task_abort(). Otherwise, pm8001_ccb_task_free() will try for dma_unmap_sg() which is invalid for task abort and can lead to kernel crash. Changes From V1: None Signed-off-by:
-
Viswas G authored
Thermal page code has been changed to 7 for the 12G controllers. Signed-off-by:
-
Viswas G authored
In Nexus reset the device state request are not needed. Signed-off-by:
-
Viswas G authored
Updated 12G linkrate to libsas. Signed-off-by:
-
Jack Wang authored
Company has policy to use company email address, so update my email address to company address. Signed-off-by:
-
