This patch makes the system wake up from suspend when an
ab8500 interrupt occur. This can for example be USB cable
insert or an RTC alarm.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch adds a file into sysfs for reading out chip id.
It has been requested for modem silent reboot.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Ludovic Barre <ludovic.barre@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

We check for dev before dereferencing it.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This adds MODULE_ALIAS entries to the various cs5535 subdevice modules; this
allows the modules to automatically be loaded when cs5535-mfd loads.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The cs5535-mfd driver now takes care of the PCI BAR handling; this
simplifies the mfgpt driver a bunch.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The cs5535-mfd driver now takes care of the PCI BAR handling; this
simplifies the gpio driver a lot.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

ARRAY_SIZE() returns size_t; use %zu instead of %d so that we don't
get warnings on x86-64.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Allow the WM8994 to completely power off, including disabling the LDOs
if they are software controlled, when it goes idle. The CODEC subdevice
controls activity for the MFD as a whole.

If the GPIOs need to be used while the device is active runtime PM
should be disabled for the device by machine specific code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Allow MFD cells to have pm_runtime_no_callbacks() called on them during
registration. This causes the runtime PM framework to ignore them,
allowing use of runtime PM to suspend the device as a whole even if
not all drivers for the MFD can usefully implement runtime PM. For
example, RTCs are likely to run continuously regardless of the power
state of the system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Replace spaces with proper tabs.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Kernel 2.6.37 adds new interrupt methods which take a struct irq_data
rather than an irq number. Convert over to these as they will become
mandatory in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Kernel 2.6.37 adds new interrupt methods which take a struct irq_data
rather than an irq number. Convert over to these as they will become
mandatory in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Kernel 2.6.37 adds new interrupt methods which take a struct irq_data
rather than an irq number. Convert over to these as they will become
mandatory in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The WM8326 is a high performance variant of the WM832x series with
no software visible differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

All the current WM832x devices have the same set of subdevices so can
just use multiple case statements with a single body.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Using %pR standardizes the struct resource output.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add an MFD driver to handle the ISA device on CS5535 and CS5536
southbridges. This ISA bridge is actually multiple devices: GPIOs,
MFGPTs, etc.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

As warned by checkpatch.pl, use #include <linux/gpio.h> instead
of <asm/gpio.h>.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

As warned by checkpatch.pl, use #include <linux/io.h> instead of <asm/io.h>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Remove KERN_<level>.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (59 commits)
  ACPI / PM: Fix build problems for !CONFIG_ACPI related to NVS rework
  ACPI: fix resource check message
  ACPI / Battery: Update information on info notification and resume
  ACPI: Drop device flag wake_capable
  ACPI: Always check if _PRW is present before trying to evaluate it
  ACPI / PM: Check status of power resources under mutexes
  ACPI / PM: Rename acpi_power_off_device()
  ACPI / PM: Drop acpi_power_nocheck
  ACPI / PM: Drop acpi_bus_get_power()
  Platform / x86: Make fujitsu_laptop use acpi_bus_update_power()
  ACPI / Fan: Rework the handling of power resources
  ACPI / PM: Register power resource devices as soon as they are needed
  ACPI / PM: Register acpi_power_driver early
  ACPI / PM: Add function for updating device power state consistently
  ACPI / PM: Add function for device power state initialization
  ACPI / PM: Introduce __acpi_bus_get_power()
  ACPI / PM: Introduce function for refcounting device power resources
  ACPI / PM: Add functions for manipulating lists of power resources
  ACPI / PM: Prevent acpi_power_get_inferred_state() from making changes
  ACPICA: Update version to 20101209
  ...

* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
  cpuidle/x86/perf: fix power:cpu_idle double end events and throw cpu_idle events from the cpuidle layer
  intel_idle: open broadcast clock event
  cpuidle: CPUIDLE_FLAG_CHECK_BM is omap3_idle specific
  cpuidle: CPUIDLE_FLAG_TLB_FLUSHED is specific to intel_idle
  cpuidle: delete unused CPUIDLE_FLAG_SHALLOW, BALANCED, DEEP definitions
  SH, cpuidle: delete use of NOP CPUIDLE_FLAGS_SHALLOW
  cpuidle: delete NOP CPUIDLE_FLAG_POLL
  ACPI: processor_idle: delete use of NOP CPUIDLE_FLAGs
  cpuidle: Rename X86 specific idle poll state[0] from C0 to POLL
  ACPI, intel_idle: Cleanup idle= internal variables
  cpuidle: Make cpuidle_enable_device() call poll_idle_init()
  intel_idle: update Sandy Bridge core C-state residency targets

* 'sfi-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-sfi-2.6:
  SFI: use ioremap_cache() instead of ioremap()

Merge branch 'vfs-scale-working' of git://git.kernel.org/pub/scm/linux/kernel/git/npiggin/linux-npiggin

* 'vfs-scale-working' of git://git.kernel.org/pub/scm/linux/kernel/git/npiggin/linux-npiggin:
  fs: fix do_last error case when need_reval_dot
  nfs: add missing rcu-walk check
  fs: hlist UP debug fixup
  fs: fix dropping of rcu-walk from force_reval_path
  fs: force_reval_path drop rcu-walk before d_invalidate
  fs: small rcu-walk documentation fixes

Fixed up trivial conflicts in Documentation/filesystems/porting

When open(2) without O_DIRECTORY opens an existing dir, it should return
EISDIR. In do_last(), the variable 'error' is initialized EISDIR, but it
is changed by d_revalidate() which returns any positive to represent
'the target dir is valid.'

Should we keep and return the initialized 'error' in this case.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>

Signed-off-by: Nick Piggin <npiggin@kernel.dk>

* 'stable/gntdev' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/p2m: Fix module linking error.
  xen p2m: clear the old pte when adding a page to m2p_override
  xen gntdev: use gnttab_map_refs and gnttab_unmap_refs
  xen: introduce gnttab_map_refs and gnttab_unmap_refs
  xen p2m: transparently change the p2m mappings in the m2p override
  xen/gntdev: Fix circular locking dependency
  xen/gntdev: stop using "token" argument
  xen: gntdev: move use of GNTMAP_contains_pte next to the map_op
  xen: add m2p override mechanism
  xen: move p2m handling to separate file
  xen/gntdev: add VM_PFNMAP to vma
  xen/gntdev: allow usermode to map granted pages
  xen: define gnttab_set_map_op/unmap_op

Fix up trivial conflict in drivers/xen/Kconfig

Merge branch 'stable/platform-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

* 'stable/platform-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen-platform: Fix compile errors if CONFIG_PCI is not enabled.
  xen: rename platform-pci module to xen-platform-pci.
  xen-platform: use PCI interfaces to request IO and MEM resources.

Po-Yu Chuang <ratbert.chuang@gmail.com> noticed that hlist_bl_set_first could
crash on a UP system when LIST_BL_LOCKMASK is 0, because

	LIST_BL_BUG_ON(!((unsigned long)h->first & LIST_BL_LOCKMASK));

always evaulates to true.

Fix the expression, and also avoid a dependency between bit spinlock
implementation and list bl code (list code shouldn't know anything
except that bit 0 is set when adding and removing elements). Eventually
if a good use case comes up, we might use this list to store 1 or more
arbitrary bits of data, so it really shouldn't be tied to locking either,
but for now they are helpful for debugging.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>

As J. R. Okajima noted, force_reval_path passes in the same dentry to
d_revalidate as the one in the nameidata structure (other callers pass in a
child), so the locking breaks. This can oops with a chrooted nfs mount, for
example. Similarly there can be other problems with revalidating a dentry
which is already in nameidata of the path walk.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>

d_revalidate can return in rcu-walk mode even when it returns 0.  We can't just
call any old dcache function on rcu-walk dentry (the dentry is unstable, so
even through d_lock can safely be taken, the result may no longer be what we
expect -- careful re-checks would be required). So just drop rcu in this case.

(I missed this conversion when switching to the rcu-walk convention that Linus
suggested)
Signed-off-by: Nick Piggin <npiggin@kernel.dk>

Signed-off-by: Nick Piggin <npiggin@kernel.dk>

In the current implementation mem_cgroup_end_migration() decides whether
the page migration has succeeded or not by checking "oldpage->mapping".

But if we are tring to migrate a shmem swapcache, the page->mapping of it
is NULL from the begining, so the check would be invalid.  As a result,
mem_cgroup_end_migration() assumes the migration has succeeded even if
it's not, so "newpage" would be freed while it's not uncharged.

This patch fixes it by passing mem_cgroup_end_migration() the result of
the page migration.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In mem_cgroup_alloc() we currently do either kmalloc() or vmalloc() then
followed by memset() to zero the memory.  This can be more efficiently
achieved by using kzalloc() and vzalloc().  There's also one situation
where we can use kzalloc_node() - this is what's new in this version of
the patch.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit b1dd693e ("memcg: avoid deadlock between move charge and
try_charge()") can cause another deadlock about mmap_sem on task migration
if cpuset and memcg are mounted onto the same mount point.

After the commit, cgroup_attach_task() has sequence like:

cgroup_attach_task()
  ss->can_attach()
    cpuset_can_attach()
    mem_cgroup_can_attach()
      down_read(&mmap_sem)        (1)
  ss->attach()
    cpuset_attach()
      mpol_rebind_mm()
        down_write(&mmap_sem)     (2)
        up_write(&mmap_sem)
      cpuset_migrate_mm()
        do_migrate_pages()
          down_read(&mmap_sem)
          up_read(&mmap_sem)
    mem_cgroup_move_task()
      mem_cgroup_clear_mc()
        up_read(&mmap_sem)

We can cause deadlock at (2) because we've already aquire the mmap_sem at (1).

But the commit itself is necessary to fix deadlocks which have existed
before the commit like:

Ex.1)
                move charge             |        try charge
  --------------------------------------+------------------------------
    mem_cgroup_can_attach()             |  down_write(&mmap_sem)
      mc.moving_task = current          |    ..
      mem_cgroup_precharge_mc()         |  __mem_cgroup_try_charge()
        mem_cgroup_count_precharge()    |    prepare_to_wait()
          down_read(&mmap_sem)          |    if (mc.moving_task)
          -> cannot aquire the lock     |    -> true
                                        |      schedule()
                                        |      -> move charge should wake it up

Ex.2)
                move charge             |        try charge
  --------------------------------------+------------------------------
    mem_cgroup_can_attach()             |
      mc.moving_task = current          |
      mem_cgroup_precharge_mc()         |
        mem_cgroup_count_precharge()    |
          down_read(&mmap_sem)          |
          ..                            |
          up_read(&mmap_sem)            |
                                        |  down_write(&mmap_sem)
    mem_cgroup_move_task()              |    ..
      mem_cgroup_move_charge()          |  __mem_cgroup_try_charge()
        down_read(&mmap_sem)            |    prepare_to_wait()
        -> cannot aquire the lock       |    if (mc.moving_task)
                                        |    -> true
                                        |      schedule()
                                        |      -> move charge should wake it up

This patch fixes all of these problems by:
1. revert the commit.
2. To fix the Ex.1, we set mc.moving_task after mem_cgroup_count_precharge()
   has released the mmap_sem.
3. To fix the Ex.2, we use down_read_trylock() instead of down_read() in
   mem_cgroup_move_charge() and, if it has failed to aquire the lock, cancel
   all extra charges, wake up all waiters, and retry trylock.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Reported-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Paul Menage <menage@google.com>
Cc: Hiroyuki Kamezawa <kamezawa.hiroyuki@gmail.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Adding the number of swap pages to the byte limit of a memory control
group makes no sense.  Convert the pages to bytes before adding them.

The only user of this code is the OOM killer, and the way it is used means
that the error results in a higher OOM badness value.  Since the cgroup
limit is the same for all tasks in the cgroup, the error should have no
practical impact at the moment.

But let's not wait for future or changing users to trip over it.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Greg Thelen <gthelen@google.com>
Cc: David Rientjes <rientjes@google.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Introduce a new bit spin lock, PCG_MOVE_LOCK, to synchronize the page
accounting and migration code.  This reworks the locking scheme of
_update_stat() and _move_account() by adding new lock bit PCG_MOVE_LOCK,
which is always taken under IRQ disable.

1. If pages are being migrated from a memcg, then updates to that
   memcg page statistics are protected by grabbing PCG_MOVE_LOCK using
   move_lock_page_cgroup().  In an upcoming commit, memcg dirty page
   accounting will be updating memcg page accounting (specifically: num
   writeback pages) from IRQ context (softirq).  Avoid a deadlocking
   nested spin lock attempt by disabling irq on the local processor when
   grabbing the PCG_MOVE_LOCK.

2. lock for update_page_stat is used only for avoiding race with
   move_account().  So, IRQ awareness of lock_page_cgroup() itself is not
   a problem.  The problem is between mem_cgroup_update_page_stat() and
   mem_cgroup_move_account_page().

Trade-off:
  * Changing lock_page_cgroup() to always disable IRQ (or
    local_bh) has some impacts on performance and I think
    it's bad to disable IRQ when it's not necessary.
  * adding a new lock makes move_account() slower.  Score is
    here.

Performance Impact: moving a 8G anon process.

Before:
	real    0m0.792s
	user    0m0.000s
	sys     0m0.780s

After:
	real    0m0.854s
	user    0m0.000s
	sys     0m0.842s

This score is bad but planned patches for optimization can reduce
this impact.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Greg Thelen <gthelen@google.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Andrea Righi <arighi@develer.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Replace usage of the mem_cgroup_update_file_mapped() memcg
statistic update routine with two new routines:
* mem_cgroup_inc_page_stat()
* mem_cgroup_dec_page_stat()

As before, only the file_mapped statistic is managed.  However, these more
general interfaces allow for new statistics to be more easily added.  New
statistics are added with memcg dirty page accounting.
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Andrea Righi <arighi@develer.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>