Simon Horman says:

====================
nfp: flower: add support for QinQ matching

Louis says:

Add new feature to the Netronome flower driver to enable QinQ offload.
This needed a bit of gymnastics in order to not break compatibility with
older firmware as the flow key sent to the firmware had to be updated
in order to make space for the extra field.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When both the driver and the firmware supports QinQ the flow key
structure that is send to the firmware is updated as the old
method of matching on VLAN did not allow for space to add another
VLAN tag. VLAN flows can now also match on the tpid field, not
constrained to just 0x8100 as before.
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a check to make sure the total length of the flow key sent to the
firmware stays within the supported limit.
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6 filters can occupy up to 4 slots and will exhaust HPFILTER
region much sooner. So, continue searching for free slots in the
HASH or NORMAL filter regions, as long as the rule's priority does
not conflict with existing rules in those regions.
Signed-off-by: Rahul Kundu <rahul.kundu@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kurt Kanzenbach says:

====================
ptp: Add generic helper functions

in order to reduce code duplication (and cut'n'paste errors) in the ptp code of
DSA, Ethernet and Phy drivers, create helper functions and move them to
ptp_classify. This way all drivers can share the same implementation.

This is version four and contains bugfixes. Implemented as discussed [1] [2]
[3] [4].

Previous versions can be found here:

 * https://lkml.kernel.org/netdev/20200723074946.14253-1-kurt@linutronix.de/
 * https://lkml.kernel.org/netdev/20200727090601.6500-1-kurt@linutronix.de/
 * https://lkml.kernel.org/netdev/20200730080048.32553-1-kurt@linutronix.de/

Thanks,
Kurt

Changes sinve v3:

 * Coding style issues (Richard Cochran, Petr Machata)
 * Add better documentation (Grygorii Strashko)
 * Fix cpts code (Grygorii Strashko)
 * Use ntohs() for TI code (Grygorii Strashko)
 * Add tags

Changes since v2:

 * Make ptp_parse_header() work in all scenarios (Russell King)
 * Fix msgtype offset for ptp v1 packets

Changes since v1:

 * Fix Kconfig (Richard Cochran)
 * Include more drivers (Richard Cochran)

[1] - https://lkml.kernel.org/netdev/20200713140112.GB27934@hoboy/
[2] - https://lkml.kernel.org/netdev/20200720142146.GB16001@hoboy/
[3] - https://lkml.kernel.org/netdev/20200723074946.14253-1-kurt@linutronix.de/
[4] - https://lkml.kernel.org/netdev/20200729100257.GX1551@shell.armlinux.org.uk/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The offset for the control field is not needed anymore. Remove it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-and-tested-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The message type is located at different offsets within the ptp header depending
on the ptp version (v1 or v2). Therefore, drivers which also deal with ptp v1
have some code for it.

Extract this into a helper function for drivers to be used.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reason: A lot of the ptp drivers - which implement hardware time stamping - need
specific fields such as the sequence id from the ptp v2 header. Currently all
drivers implement that themselves.

Introduce a generic function to retrieve a pointer to the start of the ptp v2
header.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the driver reads RX and TX subCRQ handle array directly from
a DMA-mapped buffer address when it needs to make a H_SEND_SUBCRQ
hcall. This patch stores that information in the ibmvnic_sub_crq_queue
structure instead of reading from the buffer received at login. The
overall goal of this patch is to parse relevant information from the
login response buffer and store it in the driver's private data
structures so that we don't need to read directly from the buffer and
can then free up that memory.
Signed-off-by: Cristobal Forno <cforno12@linux.ibm.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: use napi_complete_done return value

Consider the return value of napi_complete_done(), this allows users to
use the gro_flush_timeout sysfs attribute as an alternative to classic
interrupt coalescing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After making use of the gro_flush_timeout attribute I once got a
tx timeout due to an interrupt that wasn't handled. Seems using
irq_enabled can be racy, and it's not needed any longer anyway,
so remove it. I've never seen a report about such a race before,
therefore treat the change as an improvement.

There's just one small drawback: If a legacy PCI interrupt is used,
and if this interrupt is shared with a device with high interrupt
rate, then we may handle interrupts even if NAPI disabled them,
and we may see a certain performance decrease under high network load.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Consider the return value of napi_complete_done(), this allows users to
use the gro_flush_timeout sysfs attribute as an alternative to classic
interrupt coalescing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kernel documentation of L2TP has not been kept up to date and lacks
coverage of some L2TP APIs. While addressing this, refactor to improve
readability, separating the parts which focus on user APIs and
internal implementation into sections.

Changes in v2:

 - fix checkpatch warnings about trailing whitespace and long lines
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We've been warning about SO_BSDCOMPAT usage for many years. We may remove
this code completely now.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: loop: Expose VLAN table through devlink

Changes in v2:

- set the DSA configure_vlan_while_not_filtering boolean
- return the actual occupancy
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We return the VLAN table size through devlink as a simple parameter, we
do not support altering it at runtime:

devlink resource show mdio_bus/fixed-0:1f
mdio_bus/fixed-0:1f:
  name VTU size 4096 occ 0 unit entry dpipe_tables none

and after configure a bridge with VLAN filtering:

devlink resource show mdio_bus/fixed-0:1f
mdio_bus/fixed-0:1f:
  name VTU size 4096 occ 1 unit entry dpipe_tables none
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since this is a mock-up driver with no real data path for now, but we
will have one at some point, enable VLANs while not filtering.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The frags of skb_shared_info of the data is assigned in following loop. It
is meaningless to do a memcpy of frags here.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove a couple of unused #defines in cs89x0.h.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the uses of fallthrough comments to fallthrough macro.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johannes Berg says:

====================
netlink: allow NLA_BINARY length range validation

In quite a few places (perhaps particularly in wireless) we need to
validation an NLA_BINARY attribute with both a minimum and a maximum
length. Currently, we can do either of the two, but not both, given
that we have NLA_MIN_LEN (minimum length) and NLA_BINARY (maximum).

Extend the range mechanisms that we use for integer validation to
apply to NLA_BINARY as well.

After converting everything to use NLA_POLICY_MIN_LEN() we can thus
get rid of the NLA_MIN_LEN type since that's now a special case of
NLA_BINARY with a minimum length validation. Similarly, NLA_EXACT_LEN
can be specified using NLA_POLICY_EXACT_LEN() and also maps to the
new NLA_BINARY validation (min == max == desired length).

Finally, NLA_POLICY_EXACT_LEN_WARN() also gets to be a somewhat
special case of this.

I haven't included the patch here now that converts nl82011 to use
this because it doesn't apply without another cleanup patch, but
we can remove a number of hand-coded min/max length checks and get
better error messages from the general validation code while doing
that.

As I had originally built the netlink policy export to userspace in
a way that has min/max length for NLA_BINARY (for the types that we
used to call NLA_MIN_LEN, NLA_BINARY and NLA_EXACT_LEN) anyway, it
doesn't really change anything there except that now there's a chance
that userspace sees min length < max length, which previously wasn't
possible.

v2:
 * fix the min<max comment to correctly say min<=max
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add range validation for NLA_BINARY, allowing validation of any
combination of combination minimum or maximum lengths, using the
existing NLA_POLICY_RANGE()/NLA_POLICY_FULL_RANGE() macros, just
like for integers where the value is checked.

Also make NLA_POLICY_EXACT_LEN(), NLA_POLICY_EXACT_LEN_WARN()
and NLA_POLICY_MIN_LEN() special cases of this, removing the old
types NLA_EXACT_LEN and NLA_MIN_LEN.

This allows us to save some code where both minimum and maximum
lengths are requires, currently the policy only allows maximum
(NLA_BINARY), minimum (NLA_MIN_LEN) or exact (NLA_EXACT_LEN), so
a range of lengths cannot be accepted and must be checked by the
code that consumes the attributes later.

Also, this allows advertising the correct ranges in the policy
export to userspace. Here, NLA_MIN_LEN and NLA_EXACT_LEN already
were special cases of NLA_BINARY with min and min/max length
respectively.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change places that open-code NLA_POLICY_MIN_LEN() to
use the macro instead, giving us flexibility in how we
handle the details of the macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change places that open-code NLA_POLICY_EXACT_LEN() to
use the macro instead, giving us flexibility in how we
handle the details of the macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull mailmap update from Kees Cook:
 "This was originally part of my pstore tree, but when I realized that
  mailmap needed re-alphabetizing, I decided to wait until -rc1 to send
  this, as I saw a lot of mailmap additions pending in -next for the
  merge window.

  It's a programmatic reordering and the addition of a pstore
  contributor's preferred email address"

* tag 'pstore-v5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  mailmap: Add WeiXiong Liao
  mailmap: Restore dictionary sorting

Pull networking fixes from David Miller:
 "Another batch of fixes:

  1) Remove nft_compat counter flush optimization, it generates warnings
     from the refcount infrastructure. From Florian Westphal.

  2) Fix BPF to search for build id more robustly, from Jiri Olsa.

  3) Handle bogus getopt lengths in ebtables, from Florian Westphal.

  4) Infoleak and other fixes to j1939 CAN driver, from Eric Dumazet and
     Oleksij Rempel.

  5) Reset iter properly on mptcp sendmsg() error, from Florian
     Westphal.

  6) Show a saner speed in bonding broadcast mode, from Jarod Wilson.

  7) Various kerneldoc fixes in bonding and elsewhere, from Lee Jones.

  8) Fix double unregister in bonding during namespace tear down, from
     Cong Wang.

  9) Disable RP filter during icmp_redirect selftest, from David Ahern"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (75 commits)
  otx2_common: Use devm_kcalloc() in otx2_config_npa()
  net: qrtr: fix usage of idr in port assignment to socket
  selftests: disable rp_filter for icmp_redirect.sh
  Revert "net: xdp: pull ethernet header off packet after computing skb->protocol"
  phylink: <linux/phylink.h>: fix function prototype kernel-doc warning
  mptcp: sendmsg: reset iter on error redux
  net: devlink: Remove overzealous WARN_ON with snapshots
  tipc: not enable tipc when ipv6 works as a module
  tipc: fix uninit skb->data in tipc_nl_compat_dumpit()
  net: Fix potential wrong skb->protocol in skb_vlan_untag()
  net: xdp: pull ethernet header off packet after computing skb->protocol
  ipvlan: fix device features
  bonding: fix a potential double-unregister
  can: j1939: add rxtimer for multipacket broadcast session
  can: j1939: abort multipacket broadcast session when timeout occurs
  can: j1939: cancel rxtimer on multipacket broadcast session complete
  can: j1939: fix support for multipacket broadcast message
  net: fddi: skfp: cfm: Remove seemingly unused variable 'ID_sccs'
  net: fddi: skfp: cfm: Remove set but unused variable 'oldstate'
  net: fddi: skfp: smt: Remove seemingly unused variable 'ID_sccs'
  ...

A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kcalloc".
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Passing large uint32 sockaddr_qrtr.port numbers for port allocation
triggers a warning within idr_alloc() since the port number is cast
to int, and thus interpreted as a negative number. This leads to
the rejection of such valid port numbers in qrtr_port_assign() as
idr_alloc() fails.

To avoid the problem, switch to idr_alloc_u32() instead.

Fixes: bdabad3e ("net: Add Qualcomm IPC router")
Reported-by: syzbot+f31428628ef672716ea8@syzkaller.appspotmail.com
Signed-off-by: Necip Fazil Yildiran <necip@google.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

h1 is initially configured to reach h2 via r1 rather than the
more direct path through r2. If rp_filter is set and inherited
for r2, forwarding fails since the source address of h1 is
reachable from eth0 vs the packet coming to it via r1 and eth1.
Since rp_filter setting affects the test, explicitly reset it.
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

WeiXiong Liao noted to me offlist that his preference for email address
had changed and that he'd like it updated in the mailmap so people
discussing pstore/blk would be able to reach him.

Cc: WeiXiong Liao <gmpy.liaowx@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>

Several names had been recently appended (instead of inserted). While
git-shortlog doesn't need this file to be sorted, it helps humans to
keep it organized this way. Sort the entire file (which includes some
minor shuffling for dictionary order).

Done with the following commands:

	grep -E '^(#|$)' .mailmap > .mailmap.head
	grep -Ev '^(#|$)' .mailmap > .mailmap.body
 	sort -f .mailmap.body > .mailmap.body.sort
	cat .mailmap.head .mailmap.body.sort > .mailmap
	rm .mailmap.head .mailmap.body.sort
Signed-off-by: Kees Cook <keescook@chromium.org>

This reverts commit f8414a8d.

eth_type_trans() does the necessary pull on the skb.
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a kernel-doc warning for the pcs_config() function prototype:

../include/linux/phylink.h:406: warning: Excess function parameter 'permit_pause_to_mac' description in 'pcs_config'

Fixes: 7137e18f ("net: phylink: add struct phylink_pcs")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Impose a limit on the number of watches that a user can hold so that
they can't use this mechanism to fill up all the available memory.

This is done by putting a counter in user_struct that's incremented when
a watch is allocated and decreased when it is released.  If the number
exceeds the RLIMIT_NOFILE limit, the watch is rejected with EAGAIN.

This can be tested by the following means:

 (1) Create a watch queue and attach it to fd 5 in the program given - in
     this case, bash:

	keyctl watch_session /tmp/nlog /tmp/gclog 5 bash

 (2) In the shell, set the maximum number of files to, say, 99:

	ulimit -n 99

 (3) Add 200 keyrings:

	for ((i=0; i<200; i++)); do keyctl newring a$i @s || break; done

 (4) Try to watch all of the keyrings:

	for ((i=0; i<200; i++)); do echo $i; keyctl watch_add 5 %:a$i || break; done

     This should fail when the number of watches belonging to the user hits
     99.

 (5) Remove all the keyrings and all of those watches should go away:

	for ((i=0; i<200; i++)); do keyctl unlink %:a$i; done

 (6) Kill off the watch queue by exiting the shell spawned by
     watch_session.

Fixes: c73be61c ("pipe: Add general notification queue support")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>