Define appropriate macro names for consistency with other macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200629072144.24351-1-pali@kernel.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

On qcom SD host controllers voltage switching be done after the HW
is ready for it. The HW informs its readiness through power irq.
The voltage switching should happen only then.

Use the internal voltage switching and then control the voltage
switching using power irq.

IO-bus supply of eMMC would be kept always-on. So set the load
for this supply to configure it in LPM when eMMC is suspend state
and in HPM when eMMC is active.
Co-developed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Co-developed-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Co-developed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1592919288-1020-4-git-send-email-vbadigan@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Set the default power mode, MMC_POWER_UNDEFINED, in mmc_alloc_host() rather
than in mmc_start_host(). This enables host drivers to make use of the
initial state during ->probe().

Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Link:
https://lore.kernel.org/r/1592919288-1020-3-git-send-email-vbadigan@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If vendor platform drivers are controlling whole logic of voltage
switching, then sdhci driver no need control vqmmc regulator.
So skip enabling/disable vqmmc from SDHC driver.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1592919288-1020-2-git-send-email-vbadigan@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

HS400/HS200/eMMC HS doesn't have Preset Value register.
Hence, sdhci_set_ios function overrides the value set by fmw to
SDHCI_CTRL_DRV_TYPE_B.
This patch sets drv_type to MMC_SET_DRIVER_TYPE_A
so that host_control2 register gets updated with the required
strength value.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200623133347.4598-1-akshu.agrawal@amd.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

USDHC of i.MX has internal IC debug register, which record the IC
logical status. So dump these logical status in error condition,
this can help analyzing issue.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1592985830-13038-1-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In current code logic, when work in SDR12/SDR25 mode, the final clock
rate is incorrect, just the legancy 400KHz, because the
card->sw_caps.sd3_bus_mode do not has the flag SD_MODE_UHS_SDR12 or
SD_MODE_UHS_SDR25. Besides, SDIO_SPEED_SDR12 is actually value 0, and
every mode need to config the timing and clock rate, so remove the
‘if’ operator.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Tested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1592813959-5914-1-git-send-email-haibo.chen@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add support for writing new clkbuf_sel property for the J721e 4 bit IP.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-7-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For speed modes where DLL is not enabled write to TXDLYCLK to enable
transmitter delay chain mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-6-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The clock > CLOCK_TOO_SLOW_HZ condition gating phy configuration
is only required because dll should not be enabled at too low a
clock frequency or too low timing. Make sure that this condition
only gates dll enablement.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-5-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add Support for AM65x PG2.0. Use the SoC bus framework to fixup
the driver data and skip do DLL calibration if the revision is 1.0
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-4-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB flag
to indicate the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-3-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add documentation for the clock buffer select phy property in the
am654x and j721e 4 bit IP
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200619125801.9530-2-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Convert the pwrseq binding to DT schema format using json-schema.

At the same time, fix a couple of issues with the examples discovered by
the validation tool -- missing ";"
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20200622164431.3dbc8c5a@xhacker.debianSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

"K" stands for "kelvin".

While at it, make the spacing before units consistent.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200618080321.16678-1-geert+renesas@glider.beReviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Fix typo: "trigered" --> "triggered"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200617151938.30217-1-f.suligoi@asem.itSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds datactrl_mask_sdio for sdmmc revisions.
sdmmc revisions used same bit of previous ST variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200611132839.4515-1-ludovic.barre@st.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

These functions do not check the return value of devm_clk_register():
  - sdhci_arasan_register_sdcardclk()
  - sdhci_arasan_register_sampleclk()

Therefore, add the missed checks to fix them.

Fixes: c390f211 ("mmc: sdhci-of-arasan: Add ability to export card clock")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200608162226.3259186-1-hslester96@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Commit 6b5eda36 ("sdio: put active devices into 1-bit mode during
suspend") disabled 4-bit mode during system suspend. After this patch,
commit 7310ece8 ("mmc: implement SD-combo (IO+mem) support") used
new sdio_enable_4bit_bus() instead of sdio_enable_wide() to support
SD-combo cards, also for card resume. However, no corresponding support
added during suspend. That is not correct. Let's fix it.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20200609081431.6376-1-zbestahu@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If the card type is SD combo(MMC_TYPE_SD_COMBO) and the memory part does
not support wider bus(SD_SCR_BUS_WIDTH_4), nothing will be done except
return 0. However, we should check whether IO part support wider bus or
not. We should use available IO ability if supported.

In addition, there's a duplicated check to MMC_CAP_4_BIT_DATA since
sdio_enable_wide() will include that check. And we can also save one
call site to sdio_enable_wide() after this change.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20200608103009.5000-1-zbestahu@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We should return any possible error returned by mmc_io_rw_direct()
rather than only -EIO in sdio_disable_func() failure path.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200604100102.13572-1-zbestahu@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds comments about NVQUIRKS HAS_PADCALIB and NEEDS_PAD_CONTROL.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1591326240-28928-1-git-send-email-skomatineni@nvidia.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add interconnect bandwidth scaling supported strings for qcom-sdhci
controller.
Signed-off-by: Pradeep P V K <ppvk@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1591691846-7578-3-git-send-email-ppvk@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Interconnect bandwidth scaling support is now added as a
part of OPP. So, make sure interconnect driver is ready
before handling interconnect scaling.
Signed-off-by: Pradeep P V K <ppvk@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1591691846-7578-2-git-send-email-ppvk@codeaurora.orgSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The approach to allow userspace ~5s to consume the uevent, which is
triggered when a new card is inserted/initialized, currently requires the
mmc host to support system wakeup.

This is unnecessary limiting, especially for an mmc host that relies on a
GPIO IRQ for card detect. More precisely, the mmc host may not support
system wakeup for its corresponding struct device, while the GPIO IRQ still
could be configured as a wakeup IRQ via enable_irq_wake().

To support all various cases, let's simply drop the need for the wakeup
support. Instead let's always register a wakeup source and activate it for
all card detect IRQs by calling __pm_wakeup_event().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200529102341.12529-1-ulf.hansson@linaro.org

Pull Xtensa fixes from Max Filippov:

 - fix __sync_fetch_and_{and,or}_4 declarations to avoid build warning

 - update *pos in cpuinfo_op.next to avoid runtime warning

 - use for_each_set_bit in xtensa_pmu_irq_handler instead of open-coding
   it

* tag 'xtensa-20200712' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: simplify xtensa_pmu_irq_handler
  xtensa: update *pos in cpuinfo_op.next
  xtensa: fix __sync_fetch_and_{and,or}_4 declarations

Pull io_uring fixes from Jens Axboe:
 "Two late fixes again:

   - Fix missing msg_name assignment in certain cases (Pavel)

   - Correct a previous fix for full coverage (Pavel)"

* tag 'io_uring-5.8-2020-07-12' of git://git.kernel.dk/linux-block:
  io_uring: fix not initialised work->flags
  io_uring: fix missing msg_name assignment

Pull btrfs fixes from David Sterba:
 "Two refcounting fixes and one prepartory patch for upcoming splice
  cleanup:

   - fix double put of block group with nodatacow

   - fix missing block group put when remounting with discard=async

   - explicitly set splice callback (no functional change), to ease
     integrating splice cleanup patches"

* tag 'for-5.8-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: wire up iter_file_splice_write
  btrfs: fix double put of block group with nocow
  btrfs: discard: add missing put when grabbing block group from unused list

59960b9d ("io_uring: fix lazy work init") tried to fix missing
io_req_init_async(), but left out work.flags and hash. Do it earlier.

Fixes: 7cdaf587 ("io_uring: avoid whole io_wq_work copy for requests completed inline")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Ensure to set msg.msg_name for the async portion of send/recvmsg,
as the header copy will copy to/from it.

Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull RISC-V fixes from Palmer Dabbelt:
 "I have a few KGDB-related fixes. They're mostly fixes for build
  warnings, but there's also:

   - Support for the qSupported and qXfer packets, which are necessary
     to pass around GDB XML information which we need for the RISC-V GDB
     port to fully function.

   - Users can now select STRICT_KERNEL_RWX instead of forcing it on"

* tag 'riscv-for-linus-5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Avoid kgdb.h including gdb_xml.h to solve unused-const-variable warning
  kgdb: Move the extern declaration kgdb_has_hit_break() to generic kgdb.h
  riscv: Fix "no previous prototype" compile warning in kgdb.c file
  riscv: enable the Kconfig prompt of STRICT_KERNEL_RWX
  kgdb: enable arch to support XML packet.

Pull SCSI fixes from James Bottomley:
 "Five small fixes, four in driver and one in the SCSI Parallel
  transport, which fixes an incredibly old bug so I suspect no-one has
  actually used the functionality it fixes"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: dh: Add Fujitsu device to devinfo and dh lists
  scsi: mpt3sas: Fix error returns in BRM_status_show
  scsi: mpt3sas: Fix unlock imbalance
  scsi: iscsi: Change iSCSI workqueue max_active back to 1
  scsi: scsi_transport_spi: Fix function pointer check

Pull xen fix from Juergen Gross:
 "Just one fix of a recent patch (double free in an error path)"

* tag 'for-linus-5.8b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/xenbus: Fix a double free in xenbus_map_ring_pv()

Pull powerpc fix from Michael Ellerman:
 "One fix for a crash/soft lockup on Power8, caused by the exception
  rework we did in v5.7.

  Thanks to Paul Menzel and Nicholas Piggin"

* tag 'powerpc-5.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s/exception: Fix 0x1500 interrupt handler crash

Pull libnvdimm fix from Dan Williams:
 "A one-line Fix for key ring search permissions to address a regression
  from -rc1"

* tag 'libnvdimm-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm/security: Fix key lookup permissions

Pull cifs fixes from Steve French:
 "Four cifs/smb3 fixes: the three for stable fix problems found recently
  with change notification including a reference count leak"

* tag '5.8-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  cifs: fix reference leak for tlink
  smb3: fix unneeded error message on change notify
  cifs: remove the retry in cifs_poxis_lock_set
  smb3: fix access denied on change notify request to some servers

Pull coding style terminology documentation from Dan Williams:
 "The discussion has tapered off as well as the incoming ack, review,
  and sign-off tags. I did not see a reason to wait for the next merge
  window"

* tag 'inclusive-terminology' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/linux:
  CodingStyle: Inclusive Terminology

Pull networking fixes from David Miller:

 1) Restore previous behavior of CAP_SYS_ADMIN wrt loading networking
    BPF programs, from Maciej Żenczykowski.

 2) Fix dropped broadcasts in mac80211 code, from Seevalamuthu
    Mariappan.

 3) Slay memory leak in nl80211 bss color attribute parsing code, from
    Luca Coelho.

 4) Get route from skb properly in ip_route_use_hint(), from Miaohe Lin.

 5) Don't allow anything other than ARPHRD_ETHER in llc code, from Eric
    Dumazet.

 6) xsk code dips too deeply into DMA mapping implementation internals.
    Add dma_need_sync and use it. From Christoph Hellwig

 7) Enforce power-of-2 for BPF ringbuf sizes. From Andrii Nakryiko.

 8) Check for disallowed attributes when loading flow dissector BPF
    programs. From Lorenz Bauer.

 9) Correct packet injection to L3 tunnel devices via AF_PACKET, from
    Jason A. Donenfeld.

10) Don't advertise checksum offload on ipa devices that don't support
    it. From Alex Elder.

11) Resolve several issues in TCP MD5 signature support. Missing memory
    barriers, bogus options emitted when using syncookies, and failure
    to allow md5 key changes in established states. All from Eric
    Dumazet.

12) Fix interface leak in hsr code, from Taehee Yoo.

13) VF reset fixes in hns3 driver, from Huazhong Tan.

14) Make loopback work again with ipv6 anycast, from David Ahern.

15) Fix TX starvation under high load in fec driver, from Tobias
    Waldekranz.

16) MLD2 payload lengths not checked properly in bridge multicast code,
    from Linus Lüssing.

17) Packet scheduler code that wants to find the inner protocol
    currently only works for one level of VLAN encapsulation. Allow
    Q-in-Q situations to work properly here, from Toke
    Høiland-Jørgensen.

18) Fix route leak in l2tp, from Xin Long.

19) Resolve conflict between the sk->sk_user_data usage of bpf reuseport
    support and various protocols. From Martin KaFai Lau.

20) Fix socket cgroup v2 reference counting in some situations, from
    Cong Wang.

21) Cure memory leak in mlx5 connection tracking offload support, from
    Eli Britstein.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (146 commits)
  mlxsw: pci: Fix use-after-free in case of failed devlink reload
  mlxsw: spectrum_router: Remove inappropriate usage of WARN_ON()
  net: macb: fix call to pm_runtime in the suspend/resume functions
  net: macb: fix macb_suspend() by removing call to netif_carrier_off()
  net: macb: fix macb_get/set_wol() when moving to phylink
  net: macb: mark device wake capable when "magic-packet" property present
  net: macb: fix wakeup test in runtime suspend/resume routines
  bnxt_en: fix NULL dereference in case SR-IOV configuration fails
  libbpf: Fix libbpf hashmap on (I)LP32 architectures
  net/mlx5e: CT: Fix memory leak in cleanup
  net/mlx5e: Fix port buffers cell size value
  net/mlx5e: Fix 50G per lane indication
  net/mlx5e: Fix CPU mapping after function reload to avoid aRFS RX crash
  net/mlx5e: Fix VXLAN configuration restore after function reload
  net/mlx5e: Fix usage of rcu-protected pointer
  net/mxl5e: Verify that rpriv is not NULL
  net/mlx5: E-Switch, Fix vlan or qos setting in legacy mode
  net/mlx5: Fix eeprom support for SFP module
  cgroup: Fix sock_cgroup_data on big-endian.
  selftests: bpf: Fix detach from sockmap tests
  ...

CONFIG_CC_IS_GCC is undefined when Clang is used, which breaks the build
(see our Travis link below).

Clang 8 was chosen as a minimum version for this check because there
were some improvements around __builtin_constant_p in that release. In
reality, MIPS was not even buildable until clang 9 so that check was not
technically necessary. Just remove all compiler checks and just assume
that we have a working compiler.

Fixes: d4e60453 ("Restore gcc check in mips asm/unroll.h")
Link: https://travis-ci.com/github/ClangBuiltLinux/continuous-integration/jobs/359642821Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>