This fixes the initialization of the PHY TX control words in
shared memory. These control words are used for management frames
like beacons.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes beacon updating in the bottomhalf.
In case the device is busy, we will defer to later in the IRQ handler.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add new API to MAC80211 to allow low level driver to
notify MAC with driver status.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ieee80211_ioctl_giwrate() ioctl handler doesn't rcu_read_lock()
its access to the sta table, fix it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Unfortunately, debugfs can be made to access invalid memory by
open()ing a file and then waiting until the corresponding debugfs
file has been removed (and, probably, the underlying object.)

That could be exploited by any user if the user is able to open
debugfs files and can cause networking devices, STA entries or
similar to disappear which is quite easy to do.

Hence, all debugfs files should be root-only.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These are some beaconing related fixes. Basically it prevents
the card from triggering the beacon IRQ over and over again.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When doing firmware-assisted scanning, iwlwifi drivers do not
honour the regulatory control code that might disable channels
that are enabled in the EEPROM, for example when the user is
visiting another country and adjusted the regulatory domain
accordingly. This patch fixes that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When drivers receive change notification they may do work that
will enable the changes to take effect. For example, if new association
the device needs to be programmed with this information.
Give the driver chance to make the changes before notifying the
upper layer - thus preventing race condition where upper layer
attempts to utilize state that may not be configured yet.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Do not free reference to device twice. After rfkill registration succeeds
we only need to call rfkill_unregister() and not rfkill_free().
Also add some debugging.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After the workqueue is notified the LED code may be accessed. Ensure
that LED registration completes completely as part of initialization
before anything waiting on this is notified.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch replaces ieee80211chan2mhz from radiotap with
ieee80211_frequency_to_channel provided by mac80211
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch moves inline functions into iwl-core.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch make some cleanup in HW names
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Now rt2x00lib handles the initial configure_filter() command, we can
directly call lib->config_filter() in scheduled context since the
called function will no longer check if anything has changed (which is
now handled in rt2x00lib as well).

This fixes a endless loop with USB drivers where the config_filter
command was scheduled time and time again without sending any command
to the device.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If the driver does not specify a maximum power output, default to the
regulatory max.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes some timings for pre-TBTT and synthetic PU.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds some minor stuff for N-PHY support. Nothing special.
Adds Analog switching and some TODOs for RSSI processing.
Just a patch I had floating around for quite some time now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Really doesn't need to be defined four times.

Also, while at it, remove a useless macro (IEEE80211_ALIGN32_PAD)
and a function prototype for a function we don't actually have
(ieee80211_set_compression.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Because we queue the sta-debugfs-adding work on our mac80211
workqueue (which needs to be flushed under RTNL) and that work
needs the RTNL, it can currently deadlock, thanks to Reinette
Chatre for pointing out the lockdep warning about this.

This patch fixes it by moving this work to the common kernel
workqueue (using schedule_work) and canceling it as appropriate.

It also fixes a related problem: When a STA is pinned by the
debugfs adding work and sta_info_flush() runs concurrently
it is not guaranteed that all STAs are removed from the driver
before the corresponding interface is removed which may lead
to bugs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This changes the b43-PIO code to use the new SSB block-I/O.
This reduces the overhead by removing lots of function calls, pointer
dereferencing, if-conditionals any byteswapping for each packet data word.

This also fixes a harmless sparse endianness warning.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix error reported by Miles Lane <miles.lane@gmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds support for block based I/O to SSB.
This is needed in order to efficiently support PIO data
transfers to the card.
The block-I/O support is only compiled, if it's selected by the
weird driver that needs it. So there's no overhead for sane devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Thakns to Winfried Tilanus <winfried@tilanus.com> for identifying the
problem!
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes a build error when PCMCIA-host support is built,
but PCI-host support is disabled.
Hell, who on earth would use such a weird configuration. :D

drivers/built-in.o: In function `ssb_attr_sprom_store':
(.text+0x1c4b79): undefined reference to `ssb_devices_freeze'
drivers/built-in.o: In function `ssb_attr_sprom_store':
(.text+0x1c4bb3): undefined reference to `ssb_devices_thaw'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It was used only at one place anyway.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

... as it has nothing to do with pure association
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Besides code moving, I did the following changes:

* made some functions static
* removed some unneeded #include's
* made patch checkpatch.pl clean
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Besides code moving, I did the following changes:

* made some functions static
* removed some unneeded #include's
* made patch checkpatch.pl clean
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Select IWLWIFI_LEDS automatically when either IWL3945_LEDS or
IWL4965_LEDS is selected.  This avoids potential misconfigurations
which lead to build failures for iwl-led.c.

Cc: Miles Lane <miles.lane@gmail.com>
Cc: reinette.chatre@intel.com
Signed-off-by: John w. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes all kinds of warnings in iwlwifi.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlwifi/iwl-debugfs.c: In function ‘iwl_dbgfs_stations_read’:
drivers/net/wireless/iwlwifi/iwl-debugfs.c:247: warning: format ‘%llu’ expects type ‘long long unsigned int’, but argument 4 has type ‘u64’

Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch is necessary for the upcoming Accesspoint patch for p54.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Hi John,

Can you please take a look at this patch?

drivers/net/wireless/wavelan_cs.c has unusually large number
of static inline functions - 27.

I looked through them and 20 of them do not seem to warrant inlining.
Some are really big; others call mdelay(1) or busy-wait for a bit
to be set in a hardware register - it's pointless
to optimize such functions for speed.

This patch removes "inline" from these static function
(regardless of number of callsites - gcc nowadays auto-inlines
statics with one callsite).

Size difference for 32bit x86:

   text    data     bss     dec     hex filename
  17020     372       8   17400    43f8 linux-2.6-ALLYES/drivers/net/wireless/wavelan_cs.o
  14032     356       8   14396    383c linux-2.6.inline-ALLYES/drivers/net/wireless/wavelan_cs.o
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
--
vda
Signed-off-by: John W. Linville <linville@tuxdriver.com>

> prism54 should set the carrier flags correctly when it thinks the
> link can be used.

Agreed, so sure, this is OK but I rather we turn the carrier on
or off *before* sending an event, like this.
Signed-off-by: Roy Marples <uberlord@gentoo.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Turn the SSB bus suspend mechanism upside down.
Instead of deciding by an internal reference count when to suspend/resume,
let the parent bus call us in their suspend/resume routine.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds PIO support back (D'oh!) for PCMCIA devices.
This is a complete rewrite of the old PIO code. It does actually work
and we get reasonable performance out of it on a modern machine.
On a PowerBook G4 I get a few MBit for TX and a few more for RX.
So it doesn't work as well as DMA (of course), but it's a _lot_ faster
than the old PIO code (only got a few kBit with that).

The limiting factor is the host CPU speed. So it will generate 100%
CPU usage when the network interface is heavily loaded. A voluntary preemption
point in the RX path makes sure Desktop Latency isn't hurt.

PIO is needed for 16bit PCMCIA devices, as we really don't want to poke with
the braindead DMA mechanisms on PCMCIA sockets. Additionally, not all
PCMCIA sockets do actually support DMA in 16bit mode (mine doesn't).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch removes association from beacon
using bss_info_change handler for association
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds assocation capability, timestamp (tsf) and beacon interval
to bss_conf. This is required for successful assocation of iwlwifi drivers
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch eliminates the use of conf_ht in iwlwifi driver, replacing it
with bss_info_changed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch eliminates the use of conf_ht, replacing it with
bss_info_changed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>