- 26 Oct, 2011 40 commits
-
-
Andrei Warkentin authored
f39b2dd9 ("mmc: core: Bus width testing needs to handle suspend/resume") added code to only compare read-only ext_csd fields in bus width testing code, yet it's comparing some fields that are never set. The affected fields are ext_csd.raw_erased_mem_count and ext_csd.raw_partition_support. Signed-off-by:
Andrei Warkentin <andrey.warkentin@gmail.com> Acked-by:
Philip Rakity <prakity@marvell.com> Cc: <stable@kernel.org> Signed-off-by:
Chris Ball <cjb@laptop.org>
-
Yong Zhang authored
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled], we run all interrupt handlers with interrupts disabled and we even check and yell when an interrupt handler returns with interrupts enabled (see commit [b738a50a: genirq: Warn when handler enables interrupts]). So now this flag is a NOOP and can be removed. Signed-off-by:
Yong Zhang <yong.zhang0@gmail.com> Acked-by:
Kishore Kadiyala <kishore.kadiyala@ti.com> Acked-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Adrian Hunter authored
Intel Medfield platform blocks access to eMMC boot partitions which results in switch errors. Since there is no access, mmcboot0/1 devices should not be created. Add a host capability to reflect that. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Adrian Hunter authored
In the case of a switch error, do not update partition config as though the switch succeeded, and ensure blk_end_request is called on the failed request. Signed-off-by:
-
Girish K S authored
This patch adds the power class selection feature available for mmc versions 4.0 and above. During the enumeration stage before switching to the lower data bus, check if the power class is supported for the current bus width. If the power class is available then switch to the power class and use the higher data bus. If power class is not supported then switch to the lower data bus in a worst case. Signed-off-by:
Girish K S <girish.shivananjappa@linaro.org> Signed-off-by:
-
Per Forlin authored
Signed-off-by:
Per Forlin <per.forlin@linaro.org> Reviewed-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Per Forlin authored
Replace setup("fail_mmc_request") and faulty "ifdef KERNEL" with a simple module_param(). The module param mmc_core.fail_request may be used to set the fault injection attributes during boot time or module load time. Signed-off-by: -
Per Forlin authored
mmc_core module needs to use setup_fault_attr() in order to set fault injection attributes during module load time. Signed-off-by:
-
Shawn Guo authored
This patch adds the basic support for imx6q usdhc, which is a derivative of esdhc controller. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Aaron Lu authored
This is a minor fix. It makes mmc_ios_show print proper string when the host's timing is one of the newly added UHS-I modes. Signed-off-by:
Aaron Lu <aaron.lu@amd.com> Signed-off-by:
-
Guennadi Liakhovetski authored
Provide platforms with a simplified way to specify MMCIF DMA slave IDs in a way, similar to SDHI and other sh_dma clients. Signed-off-by:
-
Adrian Hunter authored
For cards that support hardware reset (just eMMC), try a reset and retry before returning an I/O error. However this is not done for ECC errors and is never done twice for the same operation type (READ, WRITE, DISCARD, SECURE DISCARD) until that type of operation again succeeds. Signed-off-by:
-
Adrian Hunter authored
MMC core provides a checking function that checks if the reset has happended. Add a test to use that function. Signed-off-by:
-
Adrian Hunter authored
Implement eMMC hardware reset for Medfield. Signed-off-by:
-
Adrian Hunter authored
Add an SDHCI operation for hardware reset and connect it to the host controller operation. Signed-off-by:
-
Adrian Hunter authored
eMMC's may have a hardware reset line. This patch provides a host controller operation to implement hardware reset and a function to reset and reinitialize the card. Also, for MMC, the reset is always performed before initialization. The host must set the new host capability MMC_CAP_HW_RESET to enable hardware reset. Signed-off-by:
-
Per Forlin authored
The error condition indicates that mmci_post_request() should cleanup after the mmci_pre_request(). In this case the resources allocated by device_prep_slave_sg() are freed by calling dmaengine_terminate_all(). dma_unmap_sg() should always be performed if the host_cookie is set. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Per Forlin authored
The err condition in post_req() is set to undo a call made to pre_req() that hasn't been started yet. The err condition is not set if an MMC request returns an error. Signed-off-by:
-
Stefan Nilsson XK authored
Earlier all cards where initiated with bus mode set as OPENDRAIN, and then later switched to PUSHPULL. According to the MMC/SD/SDIO specifications only MMC cards use OPENDRAIN during init. For both SD and SDIO the bus mode shall be PUSHPULL before attempting to init the card. The consequence of having incorrect bus mode can lead to not being able to detect the card. Therefore the default behavior have now been changed to PUSHPULL in mmc_power_up, and will only be temporarily switched when trying to attach or init a MMC card. Signed-off-by:
Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com> Signed-off-by:
Ulf HANSSON <ulf.hansson@stericsson.com> Acked-by:
-
Stefan Nilsson XK authored
Adds a quirk which can be turned on for SDIO devices that do not support 512 byte requests in byte mode during CMD53. These requests will always be sent in block mode instead. This patch also enables this quirk for ST-Ericsson CW1200 WLAN device. Signed-off-by:
-
Tanmay Upadhyay authored
Signed-off-by:
Tanmay Upadhyay <tanmay.upadhyay@einfochips.com> Acked-by:
Zhangfei Gao <zhangfei.gao@marvell.com> Signed-off-by:
-
Ulf Hansson authored
During a rescan operation mmc_attach(sd|mmc|sdio) functions are called. The error handling in these function can trigger a detach of the bus, which also meant a power off. This is not notified by the rescan operation which then continues to the next attach function. If a power off has been done, the framework must never send any new commands to the host driver, without first doing a new power up. This will most likely trigger any host driver to hang. Moving power off out of detach and instead handle power off separately when it is actually needed, solves the issue. Signed-off-by:
-
Viresh Kumar authored
Currently if card_power_gpio is passed from platform data, it is acquired and its value is either set or reset. After that we overwrite it with 1, which is not required. So, this patch removes the extra line which sets its value. Signed-off-by:
Viresh Kumar <viresh.kumar@st.com> Signed-off-by:
-
Xu lei authored
Freescale eSDHC registers only support 32-bit accesses, this patch ensures that all Freescale eSDHC register accesses are 32-bit. Signed-off-by:
Xu lei <B33228@freescale.com> Signed-off-by:
Roy Zang <tie-fei.zang@freescale.com> Signed-off-by:
Kumar Gala <galak@kernel.crashing.org> Acked-by:
Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by:
-
Balaji T K authored
Put MMC to sleep if it supports SLEEP/AWAKE (CMD5) in the mmc suspend so that Vcc (NAND core) can be cut to minimize power consumption. eMMC put into SLEEP can respond to CMD0 or H/W reset or CMD5. Current implemention on resume from suspend relies on CMD0 in mmc_init_card to get out of SLEEP mode. Signed-off-by:
Balaji T K <balajitk@ti.com> Acked-by:
Venkatraman S <svenkatr@ti.com> Reviewed-by:
Subhash Jadavani <subhashj@codeaurora.org> Acked-by:
-
Thomas Abraham authored
The default controller configuration which was previously setup by platform helper functions is moved into the driver. Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by:
Thomas Abraham <thomas.abraham@linaro.org> Acked-by:
Kukjin Kim <kgene.kim@samsung.com> Signed-off-by:
-
Daniel Drake authored
Stress-testing the runtime power management of libertas_sdio through a rmmod/insmod loop revealed that it is quite easy to cause an ETIMEDOUT failure in mmc_sdio_power_restore() leading to: libertas_sdio: probe of mmc1:0001:1 failed with error -16 Experimentation shows that a very short delay (100us) is needed in the power down path before the card can be successfully booted again. We know that this setup is lacking poweroff clamps on the card's power lines, but as only a short delay is needed, apply this unconditionally. Also bump up to 1ms sleep for extra legroom. Signed-off-by:
Daniel Drake <dsd@laptop.org> Signed-off-by:
-
Stephen Warren authored
The previous patch which implemented a DT binding for sdhci-tegra did not allow all platform data fields to be initialized from DT. The following were missing: is_8bit: Implemented by this patch. pm_flags: Not implemented yet. There are no mainline users of this field. I'm not quite sure what it's for, and hence how to represent this in DT; the value ends up being assigned to host->mmc->pm_caps. While we're at it, fix the binding documentation to refer to "SD/MMC" instead of "eSDHC", since that's the correct name; "eSDHC" was cut/paste from the Freescale binding docs. Signed-off-by:
Stephen Warren <swarren@nvidia.com> Signed-off-by:
-
Shashidhar Hiremath authored
The Patch adds the support for SDIO interrupts for all slots. It includes enabling of SDIO interrupts through dw_mci_enable_sdio_irq and the handling of the slot specific interrupts in the Interrupt Service Routine. Signed-off-by:
Shashidhar Hiremath <shashidharh@vayavyalabs.com> Acked-by:
James Hogan <james.hogan@imgtec.com> Signed-off-by:
-
Subhash Jadavani authored
If DMA resource is not available then SDCC driver should atleast work in PIO data transfer mode. Signed-off-by:
Sahitya Tummala <stummala@codeaurora.org> Signed-off-by:
David Brown <davidb@codeaurora.org> Signed-off-by:
-
Sahitya Tummala authored
Intialize busclk_timer before it is accessed in probe. Signed-off-by:
-
Sahitya Tummala authored
Not all targets have IRQ1 line routed from the SD controller to the processor. So we cannot rely on IRQ1 for PIO interrupts. This patch moves all PIO interrupts to IRQ0 and enables the PIO mode. Signed-off-by:
Murali Palnati <palnatim@codeaurora.org> Signed-off-by:
-
Sahitya Tummala authored
On some targets, MCI_IRQ_MASK1 is not routed to the MSM in which case only "cmd_irq" must be used even for PIO. With this change, all the targets will use only "cmd_irq" for both CMD and PIO. Signed-off-by:
-
Sahitya Tummala authored
For clocks that support rates which can be set (most clocks other than _pclk AHB clocks), a rate must be set using clk_set_rate() before the clock is enabled for the first time with clk_enable(). Subsequent calls to clk_enable() need not be preceded with the clk_set_rate() calls unless we wish to change the clock rate that is set previously. SDC host->clk is currently enabled without setting the clock rate even once. This patch fixes this, by ensuring that the clock rate for this clock is first set before enabling the clock. Signed-off-by:
-
Sahitya Tummala authored
Signed-off-by:
-
Alexander Tarasikov authored
This allows boards with non-standard sdio cards to fill the CIS/CCCR data. It is particularly important for old msm72k boards using wl1251. Also drop the obsolete embedded_sdio_data structure from the header as it was intended to surve a similiar purpose but was not implemented. Signed-off-by:
Alexander Tarasikov <alexander.tarasikov@gmail.com> Acked-by:
-
Alexander Tarasikov authored
The use of && instead of || caused a NULL pointer dereference if gpio setup was not passed via platform data Signed-off-by:
-
Simon Horman authored
This allows specific (non-multiplexed) IRQ handlers to be used. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Cc: Paul Mundt <lethal@linux-sh.org> Acked-by:
Magnus Damm <magnus.damm@gmail.com> Signed-off-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
Simon Horman authored
Allow named IRQs to use corresponding specific handlers. If named IRQs are used, at least an "sdcard" IRQ has to be specified by the platform. If names are not used, an arbitrary number of IRQs can be provided by the platform, in which case the generic ISR will be used for each of them. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by:
-
Simon Horman authored
Provide separate interrupt handlers which may be used by platforms where SDHI has three interrupt sources. This patch also removes the commented-out handling of CRC and other errors. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by:
-
