Pull btrfs fix from David Sterba:
 "It's been reported recently that readdir can list stale entries under
  some conditions. Fix it."

* tag 'for-4.15-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix stale entries in readdir

Pull networking fixes from David Miller:

 1) Avoid negative netdev refcount in error flow of xfrm state add, from
    Aviad Yehezkel.

 2) Fix tcpdump decoding of IPSEC decap'd frames by filling in the
    ethernet header protocol field in xfrm{4,6}_mode_tunnel_input().
    From Yossi Kuperman.

 3) Fix a syzbot triggered skb_under_panic in pppoe having to do with
    failing to allocate an appropriate amount of headroom. From
    Guillaume Nault.

 4) Fix memory leak in vmxnet3 driver, from Neil Horman.

 5) Cure out-of-bounds packet memory access in em_nbyte EMATCH module,
    from Wolfgang Bumiller.

 6) Restrict what kinds of sockets can be bound to the KCM multiplexer
    and also disallow when another layer has attached to the socket and
    made use of sk_user_data. From Tom Herbert.

 7) Fix use before init of IOTLB in vhost code, from Jason Wang.

 8) Correct STACR register write bit definition in IBM emac driver, from
    Ivan Mikhaylov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net/ibm/emac: wrong bit is used for STA control register write
  net/ibm/emac: add 8192 rx/tx fifo size
  vhost: do not try to access device IOTLB when not initialized
  vhost: use mutex_lock_nested() in vhost_dev_lock_vqs()
  i40e: flower: check if TC offload is enabled on a netdev
  qed: Free reserved MR tid
  qed: Remove reserveration of dpi for kernel
  kcm: Check if sk_user_data already set in kcm_attach
  kcm: Only allow TCP sockets to be attached to a KCM mux
  net: sched: fix TCF_LAYER_LINK case in tcf_get_base_ptr
  net: sched: em_nbyte: don't add the data offset twice
  mlxsw: spectrum_router: Don't log an error on missing neighbor
  vmxnet3: repair memory leak
  ipv6: Fix getsockopt() for sockets with default IPV6_AUTOFLOWLABEL
  pppoe: take ->needed_headroom of lower device into account on xmit
  xfrm: fix boolean assignment in xfrm_get_type_offload
  xfrm: Fix eth_hdr(skb)->h_proto to reflect inner IP version
  xfrm: fix error flow in case of add state fails
  xfrm: Add SA to hardware at the end of xfrm_state_construct()

Pull sparc bugfix from David Miller:
 "Sparc Makefile typo fix"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: fix typo in CONFIG_CRYPTO_DES_SPARC64 => CONFIG_CRYPTO_CAMELLIA_SPARC64

STA control register has areas of mode and opcodes for opeations. 18 bit is
using for mode selection, where 0 is old MIO/MDIO access method and 1 is
indirect access mode. 19-20 bits are using for setting up read/write
operation(STA opcodes). In current state 'read' is set into old MIO/MDIO mode
with 19 bit and write operation is set into 18 bit which is mode selection,
not a write operation. To correlate write with read we set it into 20 bit.
All those bit operations are MSB 0 based.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

emac4syn chips has availability to use 8192 rx/tx fifo buffer sizes,
in current state if we set it up in dts 8192 as example, we will get
only 2048 which may impact on network speed.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code will try to access dev->iotlb when processing
VHOST_IOTLB_INVALIDATE even if it was not initialized which may lead
to NULL pointer dereference. Fixes this by check dev->iotlb before.

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We used to call mutex_lock() in vhost_dev_lock_vqs() which tries to
hold mutexes of all virtqueues. This may confuse lockdep to report a
possible deadlock because of trying to hold locks belong to same
class. Switch to use mutex_lock_nested() to avoid false positive.

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Reported-by: syzbot+dbb7c1161485e61b0241@syzkaller.appspotmail.com
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.

Fixes: 2f4b411a ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a7 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the typo CONFIG_CRYPTO_DES_SPARC64 => CONFIG_CRYPTO_CAMELLIA_SPARC64

Fixes: 81658ad0 ("sparc64: Add CAMELLIA driver making use of the new camellia opcodes.")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michal Kalderon says:

====================
qed: rdma bug fixes

This patch contains two small bug fixes related to RDMA.
Both related to resource reservations.
====================
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A tid was allocated for reserved MR during initialization but
not freed. This lead to an annoying output message during
rdma unload flow.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Double reservation for kernel dedicated dpi was performed.
Once in the core module and once in qedr.
Remove the reservation from core.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
kcm: fix two syzcaller issues

In this patch set:

- Don't allow attaching non-TCP or listener sockets to a KCM mux.
- In kcm_attach Check if sk_user_data is already set. This is
  under lock to avoid race conditions. More work is need to make
  all of the users of sk_user_data to use the same locking.

- v2
  Remove unncessary check for not PF_KCM in kcm_attach (suggested by
  Guillaume Nault)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This is needed to prevent sk_user_data being overwritten.
The check is done under the callback lock. This should prevent
a socket from being attached twice to a KCM mux. It also prevents
a socket from being attached for other use cases of sk_user_data
as long as the other cases set sk_user_data under the lock.
Followup work is needed to unify all the use cases of sk_user_data
to use the same locking.

Reported-by: syzbot+114b15f2be420a8886c3@syzkaller.appspotmail.com
Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Signed-off-by: Tom Herbert <tom@quantonium.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP sockets for IPv4 and IPv6 that are not listeners or in closed
stated are allowed to be attached to a KCM mux.

Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+8865eaff7f9acd593945@syzkaller.appspotmail.com
Signed-off-by: Tom Herbert <tom@quantonium.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update my email address.
Signed-off-by: James Morris <jmorris@namei.org>

TCF_LAYER_LINK and TCF_LAYER_NETWORK returned the same pointer as
skb->data points to the network header.
Use skb_mac_header instead.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'ptr' is shifted by the offset and then validated,
the memcmp should not add it a second time.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In fixing the readdir+pagefault deadlock I accidentally introduced a
stale entry regression in readdir.  If we get close to full for the
temporary buffer, and then skip a few delayed deletions, and then try to
add another entry that won't fit, we will emit the entries we found and
retry.  Unfortunately we delete entries from our del_list as we find
them, assuming we won't need them.  However our pos will be with
whatever our last entry was, which could be before the delayed deletions
we skipped, so the next search will add the deleted entries back into
our readdir buffer.  So instead don't delete entries we find in our
del_list so we can make sure we always find our delayed deletions.  This
is a slight perf hit for readdir with lots of pending deletions, but
hopefully this isn't a common occurrence.  If it is we can revist this
and optimize it.

cc: stable@vger.kernel.org
Fixes: 23b5ec74 ("btrfs: fix readdir deadlock with pagefault")
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>

Pull tracing fixes from Steven Rostedt:
 "With the new ORC unwinder, ftrace stack tracing became disfunctional.

  One was that ORC didn't know how to handle the ftrace callbacks in
  general (which Josh fixed).

  The other was that ORC would just bail if it hit a dynamically
  allocated trampoline. Which means all ftrace stack tracing that
  happens from the function tracer would produce no results (that
  includes killing the max stack size tracer). I added a check to the
  ORC unwinder to see if the trampoline belonged to ftrace, and if it
  did, use the orc entry of the static trampoline that was used to
  create the dynamic one (it would be identical).

  Finally, I noticed that the skip values of the stack tracing were out
  of whack. I went through and fixed them up"

* tag 'trace-v4.15-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Update stack trace skipping for ORC unwinder
  ftrace, orc, x86: Handle ftrace dynamically allocated trampolines
  x86/ftrace: Fix ORC unwinding from ftrace handlers

We're seeing a raise of automated reports from testing tools and reports
about address leaks that are not really exploitable as-is, many of which
do not represent an immediate risk justifying to work in closed places.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 6cfb521a.

Turns out distros do not want to make retpoline as part of their "ABI",
so this patch should not have been merged.  Sorry Andi, this was my
fault, I suggested it when your original patch was the "correct" way of
doing this instead.
Reported-by: Jiri Kosina <jikos@kernel.org>
Fixes: 6cfb521a ("module: Add retpoline tag to VERMAGIC")
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: rusty@rustcorp.com.au
Cc: arjan.van.de.ven@intel.com
Cc: jeyu@kernel.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Driver periodically samples all neighbors configured in device
in order to update the kernel regarding their state. When finding
an entry configured in HW that doesn't show in neigh_lookup()
driver logs an error message.
This introduces a race when removing multiple neighbors -
it's possible that a given entry would still be configured in HW
as its removal is still being processed but is already removed
from the kernel's neighbor tables.

Simply remove the error message and gracefully accept such events.

Fixes: c723c735 ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Fixes: 60f040ca ("mlxsw: spectrum_router: Periodically dump active IPv6 neighbours")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net): ipsec 2018-01-24

1) Only offloads SAs after they are fully initialized.
   Otherwise a NIC may receive packets on a SA we can
   not yet handle in the stack.
   From Yossi Kuperman.

2) Fix negative refcount in case of a failing offload.
   From Aviad Yehezkel.

3) Fix inner IP ptoro version when decapsulating
   from interaddress family tunnels.
   From Yossi Kuperman.

4) Use true or false for boolean variables instead of an
   integer value in xfrm_get_type_offload.
   From Gustavo A. R. Silva.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

with the introduction of commit
b0eb57cb, it appears that rq->buf_info
is improperly handled.  While it is heap allocated when an rx queue is
setup, and freed when torn down, an old line of code in
vmxnet3_rq_destroy was not properly removed, leading to rq->buf_info[0]
being set to NULL prior to its being freed, causing a memory leak, which
eventually exhausts the system on repeated create/destroy operations
(for example, when  the mtu of a vmxnet3 interface is changed
frequently.

Fix is pretty straight forward, just move the NULL set to after the
free.

Tested by myself with successful results

Applies to net, and should likely be queued for stable, please
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-By: boyang@redhat.com
CC: boyang@redhat.com
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: David S. Miller <davem@davemloft.net>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 513674b5 ("net: reevalulate autoflowlabel setting after
sysctl setting") removed the initialisation of
ipv6_pinfo::autoflowlabel and added a second flag to indicate
whether this field or the net namespace default should be used.

The getsockopt() handling for this case was not updated, so it
currently returns 0 for all sockets for which IPV6_AUTOFLOWLABEL is
not explicitly enabled.  Fix it to return the effective value, whether
that has been set at the socket or net namespace level.

Fixes: 513674b5 ("net: reevalulate autoflowlabel setting after sysctl ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

In pppoe_sendmsg(), reserving dev->hard_header_len bytes of headroom
was probably fine before the introduction of ->needed_headroom in
commit f5184d26 ("net: Allow netdevices to specify needed head/tailroom").

But now, virtual devices typically advertise the size of their overhead
in dev->needed_headroom, so we must also take it into account in
skb_reserve().
Allocation size of skb is also updated to take dev->needed_tailroom
into account and replace the arbitrary 32 bytes with the real size of
a PPPoE header.

This issue was discovered by syzbot, who connected a pppoe socket to a
gre device which had dev->header_ops->create == ipgre_header and
dev->hard_header_len == 0. Therefore, PPPoE didn't reserve any
headroom, and dev_hard_header() crashed when ipgre_header() tried to
prepend its header to skb->data.

skbuff: skb_under_panic: text:000000001d390b3a len:31 put:24
head:00000000d8ed776f data:000000008150e823 tail:0x7 end:0xc0 dev:gre0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
    (ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 3670 Comm: syzkaller801466 Not tainted
4.15.0-rc7-next-20180115+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:skb_panic+0x162/0x1f0 net/core/skbuff.c:100
RSP: 0018:ffff8801d9bd7840 EFLAGS: 00010282
RAX: 0000000000000083 RBX: ffff8801d4f083c0 RCX: 0000000000000000
RDX: 0000000000000083 RSI: 1ffff1003b37ae92 RDI: ffffed003b37aefc
RBP: ffff8801d9bd78a8 R08: 1ffff1003b37ae8a R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff86200de0
R13: ffffffff84a981ad R14: 0000000000000018 R15: ffff8801d2d34180
FS:  00000000019c4880(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000208bc000 CR3: 00000001d9111001 CR4: 00000000001606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
  skb_under_panic net/core/skbuff.c:114 [inline]
  skb_push+0xce/0xf0 net/core/skbuff.c:1714
  ipgre_header+0x6d/0x4e0 net/ipv4/ip_gre.c:879
  dev_hard_header include/linux/netdevice.h:2723 [inline]
  pppoe_sendmsg+0x58e/0x8b0 drivers/net/ppp/pppoe.c:890
  sock_sendmsg_nosec net/socket.c:630 [inline]
  sock_sendmsg+0xca/0x110 net/socket.c:640
  sock_write_iter+0x31a/0x5d0 net/socket.c:909
  call_write_iter include/linux/fs.h:1775 [inline]
  do_iter_readv_writev+0x525/0x7f0 fs/read_write.c:653
  do_iter_write+0x154/0x540 fs/read_write.c:932
  vfs_writev+0x18a/0x340 fs/read_write.c:977
  do_writev+0xfc/0x2a0 fs/read_write.c:1012
  SYSC_writev fs/read_write.c:1085 [inline]
  SyS_writev+0x27/0x30 fs/read_write.c:1082
  entry_SYSCALL_64_fastpath+0x29/0xa0

Admittedly PPPoE shouldn't be allowed to run on non Ethernet-like
interfaces, but reserving space for ->needed_headroom is a more
fundamental issue that needs to be addressed first.

Same problem exists for __pppoe_xmit(), which also needs to take
dev->needed_headroom into account in skb_cow_head().

Fixes: f5184d26 ("net: Allow netdevices to specify needed head/tailroom")
Reported-by: syzbot+ed0838d0fa4c4f2b528e20286e6dc63effc7c14d@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the addition of ORC unwinder and FRAME POINTER unwinder, the stack
trace skipping requirements have changed.

I went through the tracing stack trace dumps with ORC and with frame
pointers and recalculated the proper values.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

The function tracer can create a dynamically allocated trampoline that is
called by the function mcount or fentry hook that is used to call the
function callback that is registered. The problem is that the orc undwinder
will bail if it encounters one of these trampolines. This breaks the stack
trace of function callbacks, which include the stack tracer and setting the
stack trace for individual functions.

Since these dynamic trampolines are basically copies of the static ftrace
trampolines defined in ftrace_*.S, we do not need to create new orc entries
for the dynamic trampolines. Finding the return address on the stack will be
identical as the functions that were copied to create the dynamic
trampolines. When encountering a ftrace dynamic trampoline, we can just use
the orc entry of the ftrace static function that was copied for that
trampoline.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

Pull PCI fix from Bjorn Helgaas:
 "Fix AMD regression due to not re-enabling the big window on resume
  (Christian König)"

* tag 'pci-v4.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  x86/PCI: Enable AMD 64-bit window on resume

Steven Rostedt discovered that the ftrace stack tracer is broken when
it's used with the ORC unwinder.  The problem is that objtool is
instructed by the Makefile to ignore the ftrace_64.S code, so it doesn't
generate any ORC data for it.

Fix it by making the asm code objtool-friendly:

- Objtool doesn't like the fact that save_mcount_regs pushes RBP at the
  beginning, but it's never restored (directly, at least).  So just skip
  the original RBP push, which is only needed for frame pointers anyway.

- Annotate some functions as normal callable functions with
  ENTRY/ENDPROC.

- Add an empty unwind hint to return_to_handler().  The return address
  isn't on the stack, so there's nothing ORC can do there.  It will just
  punt in the unlikely case it tries to unwind from that code.

With all that fixed, remove the OBJECT_FILES_NON_STANDARD Makefile
annotation so objtool can read the file.

Link: http://lkml.kernel.org/r/20180123040746.ih4ep3tk4pbjvg7c@trebleReported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

Pull networking fixes from David Miller:

 1) Fix divide by zero in mlx5, from Talut Batheesh.

 2) Guard against invalid GSO packets coming from untrusted guests and
    arriving in qdisc_pkt_len_init(), from Eric Dumazet.

 3) Similarly add such protection to the various protocol GSO handlers.
    From Willem de Bruijn.

 4) Fix regression added to IGMP source address checking for IGMPv3
    reports, from Felix Feitkau.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  tls: Correct length of scatterlist in tls_sw_sendpage
  be2net: restore properly promisc mode after queues reconfiguration
  net: igmp: fix source address check for IGMPv3 reports
  gso: validate gso_type in GSO handlers
  net: qdisc_pkt_len_init() should be more robust
  ibmvnic: Allocate and request vpd in init_resources
  ibmvnic: Revert to previous mtu when unsupported value requested
  ibmvnic: Modify buffer size and number of queues on failover
  rds: tcp: compute m_ack_seq as offset from ->write_seq
  usbnet: silence an unnecessary warning
  cxgb4: fix endianness for vlan value in cxgb4_tc_flower
  cxgb4: set filter type to 1 for ETH_P_IPV6
  net/mlx5e: Fix fixpoint divide exception in mlx5e_am_stats_compare

Assign true or false to boolean variables instead of an integer value.

This issue was detected with the help of Coccinelle.

Fixes: ffdb5211 ("xfrm: Auto-load xfrm offload modules")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

IPSec tunnel mode supports encapsulation of IPv4 over IPv6 and vice-versa.

The outer IP header is stripped and the inner IP inherits the original
Ethernet header. Tcpdump fails to properly decode the inner packet in
case that h_proto is different than the inner IP version.

Fix h_proto to reflect the inner IP version.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>

Commit bdcf0a42 ("kernel: make groups_sort calling a responsibility
group_info allocators") appears to break nfsd rootsquash in a pretty
major way.

It adds a call to groups_sort() inside the loop that copies/squashes
gids, which means the valid gids are sorted along with the following
garbage.  The net result is that the highest numbered valid gids are
replaced with any lower-valued garbage gids, possibly including 0.

We should sort only once, after filling in all the gids.

Fixes: bdcf0a42 ("kernel: make groups_sort calling a responsibility ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In orangefs_devreq_read, there is a loop which picks an op off the list
of pending ops.  If the loop fails to find an op, there is nothing to
read, and it returns EAGAIN.  If the op has been given up on, the loop
is restarted via a goto.  The bug is that the variable which the found
op is written to is not reinitialized, so if there are no more eligible
ops on the list, the code runs again on the already handled op.

This is triggered by interrupting a process while the op is being copied
to the client-core.  It's a fairly small window, but it's there.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

set_op_state_purged can delete the op.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The scatterlist is reused by both sendmsg and sendfile.
If a sendmsg of smaller number of pages is followed by a sendfile
of larger number of pages, the scatterlist may be too short, resulting
in a crash in gcm_encrypt.

Add sg_unmark_end to make the list the correct length.

tls_sw_sendmsg already calls sg_unmark_end correctly when it allocates
memory in alloc_sg, or in zerocopy_from_iter.
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 62219066 ("be2net: Request RSS capability of Rx interface
depending on number of Rx rings") modified be_update_queues() so the
IFACE (HW representation of the netdevice) is destroyed and then
re-created. This causes a regression because potential promiscuous mode
is not restored properly during be_open() because the driver thinks
that the HW has promiscuous mode already enabled.

Note that Lancer is not affected by this bug because RX-filter flags are
disabled during be_close() for this chipset.

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>

Fixes: 62219066 ("be2net: Request RSS capability of Rx interface depending on number of Rx rings")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit "net: igmp: Use correct source address on IGMPv3 reports"
introduced a check to validate the source address of locally generated
IGMPv3 packets.
Instead of checking the local interface address directly, it uses
inet_ifa_match(fl4->saddr, ifa), which checks if the address is on the
local subnet (or equal to the point-to-point address if used).

This breaks for point-to-point interfaces, so check against
ifa->ifa_local directly.

Cc: Kevin Cernekee <cernekee@chromium.org>
Fixes: a46182b0 ("net: igmp: Use correct source address on IGMPv3 reports")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>