Skip to content

L
linux
Switch branch/tag
  1. 08 Nov, 2019 33 commits
  3. 07 Nov, 2019 7 commits
    • Madalin Bucur's avatar
      net: phy: at803x: add missing dependency on CONFIG_REGULATOR · dddb318b
      Madalin Bucur authored 
      Compilation fails on PPC targets as CONFIG_REGULATOR is not set and
drivers/regulator/devres.c is not compiled in while functions exported
there are used by drivers/net/phy/at803x.c. Here's the error log:

  LD      .tmp_vmlinux1
drivers/net/phy/at803x.o: In function `at803x_rgmii_reg_set_voltage_sel':
drivers/net/phy/at803x.c:294: undefined reference to `.rdev_get_drvdata'
drivers/net/phy/at803x.o: In function `at803x_rgmii_reg_get_voltage_sel':
drivers/net/phy/at803x.c:306: undefined reference to `.rdev_get_drvdata'
drivers/net/phy/at803x.o: In function `at8031_register_regulators':
drivers/net/phy/at803x.c:359: undefined reference to `.devm_regulator_register'
drivers/net/phy/at803x.c:365: undefined reference to `.devm_regulator_register'
drivers/net/phy/at803x.o:(.data.rel+0x0): undefined reference to `regulator_list_voltage_table'
linux/Makefile:1074: recipe for target 'vmlinux' failed
make[1]: *** [vmlinux] Error 1

Fixes: 2f664823 ("net: phy: at803x: add device tree binding")
Signed-off-by: default avatarMadalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: default avatarFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      dddb318b
    • Ioana Ciornei's avatar
      dpaa2-eth: add ethtool MAC counters · 991df1fb
      Ioana Ciornei authored 
      When a DPNI is connected to a MAC, export its associated counters.
Ethtool related functions are added in dpaa2_mac for returning the
number of counters, their strings and also their values.
Signed-off-by: default avatarIoana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      991df1fb
    • Michael Walle's avatar
      enetc: ethtool: add wake-on-lan callbacks · 88c8562b
      Michael Walle authored 
      If there is an external PHY, pass the wake-on-lan request to the PHY.
Signed-off-by: default avatarMichael Walle <michael@walle.cc>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      88c8562b
    • Michael Walle's avatar
      enetc: add ioctl() support for PHY-related ops · a613bafe
      Michael Walle authored 
      If there is an attached PHY try to handle the requested ioctl with its
handler, which allows the userspace to access PHY registers, for
example. This will make mii-diag and similar tools work.
Signed-off-by: default avatarMichael Walle <michael@walle.cc>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a613bafe
    • Wei Yongjun's avatar
      mlxsw: spectrum: Fix error return code in mlxsw_sp_port_module_info_init() · 630d4e75
      Wei Yongjun authored 
      Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.

Fixes: 4a7f970f ("mlxsw: spectrum: Replace port_to_module array with array of structs")
Signed-off-by: default avatarWei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: default avatarJiri Pirko <jiri@mellanox.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      630d4e75
    • David S. Miller's avatar
      Merge branch 'cxgb4-add-support-for-TC-MQPRIO-Qdisc-Offload' · 69625ea7
      David S. Miller authored 
      Rahul Lakkireddy says:

====================
cxgb4: add support for TC-MQPRIO Qdisc Offload

This series of patches add support for offloading TC-MQPRIO Qdisc
to Chelsio T5/T6 NICs. Offloading QoS traffic shaping and pacing
requires using Ethernet Offload (ETHOFLD) resources available on
Chelsio NICs. The ETHOFLD resources are configured by firmware
and taken from the resource pool shared with other Chelsio Upper
Layer Drivers. Traffic flowing through ETHOFLD region requires a
software netdev Tx queue (EOSW_TXQ) exposed to networking stack,
and an underlying hardware Tx queue (EOHW_TXQ) used for sending
packets through hardware.

ETHOFLD region is addressed using EOTIDs, which are per-connection
resource. Hence, EOTIDs are capable of storing only a very small
number of packets in flight. To allow more connections to share
the the QoS rate limiting configuration, multiple EOTIDs must be
allocated to reduce packet drops. EOTIDs are 1-to-1 mapped with
software EOSW_TXQ. Several software EOSW_TXQs can post packets to
a single hardware EOHW_TXQ.

The series is broken down as follows:

Patch 1 queries firmware for maximum available traffic classes,
as well as, start and maximum available indices (EOTID) into ETHOFLD
region, supported by the underlying device.

Patch 2 reworks queue configuration and simplifies MSI-X allocation
logic in preparation for ETHOFLD queues support.

Patch 3 adds skeleton for validating and configuring TC-MQPRIO Qdisc
offload. Also, adds support for software EOSW_TXQs and exposes them
to network stack. Updates Tx queue selection to use fallback NIC Tx
path for unsupported traffic that can't go through ETHOFLD queues.

Patch 4 adds support for managing hardware queues to rate limit
traffic flowing through them. The queues are allocated/removed based
on enabling/disabling TC-MQPRIO Qdisc offload, respectively.

Patch 5 adds Tx path for traffic flowing through software EOSW_TXQ
and EOHW_TXQ. Also, adds Rx path to handle Tx completions.

Patch 6 updates exisiting SCHED API to configure FLOWC based QoS
offload. In the existing QUEUE based rate limiting, multiple queues
sharing a traffic class get the aggreagated max rate limit value.
On the other hand, in FLOWC based rate limiting, multiple queues
sharing a traffic class get their own individual max rate limit
value. For example, if 2 queues are bound to class 0, which is rate
limited to 1 Gbps, then in QUEUE based rate limiting, both the
queues get the aggregate max output of 1 Gbps only. In FLOWC based
rate limiting, each queue gets its own output of max 1 Gbps each;
i.e. 2 queues * 1 Gbps rate limit = 2 Gbps max output.
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      69625ea7
    • Rahul Lakkireddy's avatar
      cxgb4: add FLOWC based QoS offload · 0e395b3c
      Rahul Lakkireddy authored 
      Rework SCHED API to allow offloading TC-MQPRIO QoS configuration.
The existing QUEUE based rate limiting throttles all queues sharing
a traffic class, to the specified max rate limit value. So, if
multiple queues share a traffic class, then all the queues get
the aggregate specified max rate limit.

So, introduce the new FLOWC based rate limiting, where multiple
queues can share a traffic class with each queue getting its own
individual specified max rate limit.

For example, if 2 queues are bound to class 0, which is rate limited
to 1 Gbps, then 2 queues using QUEUE based rate limiting, get the
aggregate output of 1 Gbps only. In FLOWC based rate limiting, each
queue gets its own output of max 1 Gbps each; i.e. 2 queues * 1 Gbps
rate limit = 2 Gbps.
Signed-off-by: default avatarRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      0e395b3c
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7