This patch defines common Armada XP pinctrl settings in armada-xp.dtsi
for the supported SPI interface (MPP36-39) and use it as default
for Armada XP spi interface. That being done, it removes the now
redundant definitions in armada-xp-axpwifiap.dts.

Note: this patch has the potential to break out-of-tree users w/o
specific pinctrl settings for their spi interfaces if the default
above does not match their config (i.e. if they do not use CS0).
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/d404b7abd80ee5a0fd8e8d3586d33cd37740d589.1416613429.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

This patch defines common Armada XP pinctrl settings for uart2 and
uart3 interfaces (uart0 and uart1 rx/tx do not rely on MPP):

 uart2: MPP42-43 as default
 uart3: MPP44-45 as default
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/fd51c080c7139a67ec01df8d797f1e88ce557796.1416613429.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

This patch defines common Armada 370 pinctrl settings for uart0 and
uart1 interfaces:

 uart0: MPP0-1 as default
 uart1: MPP41-42 as default

Note: this patch has the potential to break out-of-tree users w/o
specific pinctrl settings for their uart interfaces if the default
above does not match their config.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/31412e57955c98bc9cc47b70726b5072af945cc3.1416613429.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

This patch defines common Armada 370 pinctrl settings for spi0 and spi1
interfaces:

 spi0: MPP33-36 as default, MPP32,63-65 as available alternate config
 spi1: MPP49-52 as default

Currently, the Armada 370 DB .dts file has no explicit pinctrl info
for the spi0 interface used to access the flash on the board. The
patch fixes that by also adding explicit pinctrl info (MPP32,63-65)
for this SPI interface.

Note: this patch has the potential to break out-of-tree users w/o
specific pinctrl settings for their spi interfaces if the default
above does not match their config.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/1e812eb63b37718e273463e22e4d7512f8f0b624.1416613429.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

What was done by Sebastian in 264a05e1 ("ARM: mvebu: armada-xp:
Add node alias to pinctrl and add base address") and 01c43422
("ARM: mvebu: armada-xp: Use pinctrl node alias") can also be done for
Armada 370, i.e.

 - Rename Armada 370 pinctrl node to pin-ctrl with its address encoded
 - Add a node alias to access the pinctrl node easily.
 - use the newly available alias in existing Armada 370 .dts files

We can even go a bit further by putting the pinctrl node definition in
armada-370-xp.dtsi, with only its reg property defined. This allows us
to then also use the newly defined node alias in armada-xp.dtsi,
armada-370.dtsi.
Suggested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/b54eb45e5242728aace3ce8aef2eae4251f8dea3.1416613429.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

Now that labels for uartX are available in Marvell Armada .dtsi files,
this patch replaces the "/soc/internal-regs/serial@12000" found in
armada-xp-lenovo-ix4-300d.dts file for stdout-path property by the more
concise &uart0.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/d1a883510e01f7f212a385e826dccbef903fae42.1416613429.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

This patch adds uartX labels for Armada SoC serial nodes. This is
a preliminary work to be able to easily reference the serial lines
in Device Tree files. One expected use is when providing stdout-path
property for barebox.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/0683d1a823fe9b75849f3dafcf1cf6ee291cdca6.1416613429.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

As reported by Andrew, the vendor prefix for Seiko Instruments, Inc.
S-35390A I2C RTC chip in kirkwood-synology.dtsi has a typo (ssi
instead of sii). This patches fixes it.

Note: i2c devices ignore the optional vendor prefix, which explains
why it worked with the typo and also why there is no backward
compatibility issues with the fix.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Link: https://lkml.kernel.org/r/0444140a267d982c3e5f5f2b7b5f2dc41d010e2a.1416613429.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

Commit a095b1c7 ("ARM: mvebu: sort DT nodes by address")
missed placing the system-controller in the correct order.

Fixes: a095b1c7 ("ARM: mvebu: sort DT nodes by address")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/20141114204333.GS27002@pengutronix.deSigned-off-by: Jason Cooper <jason@lakedaemon.net>

In order to update MAC address entries in the ethernet nodes in Device Tree
both mainline U-Boot and Barebox bootloaders accept the same format of aliases,
which is 'ethernetX', where X stands for an interface number.
Other platforms in the mainline Linux, that comprise ethernet references in
'/aliases' node (like various flavours of imx or sunXi), follow the naming
scheme described above.

This commit ajusts ethernet aliases of Marvell Armada 38x SoC to be properly
recognized by bootloaders' MAC address fixup routines.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-5-git-send-email-mw@semihalf.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

For proper operation of Armada 38x SDHCI controller proper 'clocks' property
is sufficient. Therefore it is not useful to keep an additional
'clock-frequency' property in SDHCI controller node of board-level Device Tree
file for Armada 385 DB.

This commit gets rid of useless 'clock-frequency' property.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-4-git-send-email-mw@semihalf.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

The Marvell Armada 38x SoC's SDHCI interface is capable of using 1.8v voltage,
needed for driving "UHS-I" SD cards at their full speed. It is not, however,
possible on the DB board. Due to physical connectivity connector supply is tied
to 3v and any attempt of changing voltage in order to operate in the fastest UHS
modes fails.

This patch enables equivalent SDHCI quirk in order to adjust controller
operation to system capabilities.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415980652-7429-3-git-send-email-mw@semihalf.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

The 370 rd has a 7 port, mv88E6182 switch, connected to eth1.  Add a
fixed-link subnode to the ethernet device tree node, to force
gigabit/full duplex.  Add a dsa node, with describing the four used
ports. This requires adding an alias to the mdio node, so it can be
referenced as a phandle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415214121-29286-3-git-send-email-andrew@lunn.chSigned-off-by: Jason Cooper <jason@lakedaemon.net>

This commit modifies the Armada 370 and Armada 370 DB Device Tree
descriptions to use the simple-card DT binding to describe the audio
complex of the Armada 370 DB instead of a custom audio machine driver.

To do so, it:

 - Adds the sound-dai-cells properties to the CS42L51 node, the audio
   controller node and the SPDIF in/out nodes.

 - Completely changes the description of the sound complex to use the
   "simple-audio-card" DT binding instead of the
   "marvell,a370db-audio" DT binding.

 - Fixes the indentation to properly use tabs instead of spaces.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414512524-24466-6-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

Back when audio was enabled, the muxing of some MPP pins was causing
problems. However, since commit fea038ed ("ARM: mvebu: Add proper
pin muxing on the Armada 370 DB board"), those problematic MPP pins
have been assigned a proper muxing for the Ethernet interfaces. This
proper muxing is now conflicting with the hog pins muxing that had
been added as part of 249f3822 ("ARM: mvebu: add audio support to
Armada 370 DB").

Therefore, this commit simply removes the hog pins muxing, which
solves a warning a boot time due to the conflicting muxing
requirements.

Fixes: fea038ed ("ARM: mvebu: Add proper pin muxing on the Armada 370 DB board")
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414512524-24466-5-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

There is only one 74hc595 connected to GPIO but two were given
in the registers-number property. Fix it up.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

There is an I2C eeprom connected on Lenovo ix4-300d, add the
corresponding node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Lenovo ix4-300d has two ethernet PHYs connected via RGMII. Add the
corresponding pinctrl settings.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

There is a GMII setting for GE0, add it to the common pinctrl node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Pinctrl settings for GE0 and GE1 are not only usable on RD-AXPWiFiAP.
Moreover, naming the RGMII settings pmx-ge{0,1} is not precise enough
as there is also a GMII setting for GE0.

Move the pinctrl sub-nodes to the common pinctrl node and rename them
to pmx-ge{0,1}-rgmii.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Armada XP pinctrl node gained an alias, make use of it.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

In other MVEBU SoCs, the pin controller node is called pin-ctrl with
its base address added. Also, we have a node alias to access the pinctrl
node easily. Fix this for Armada XP pinctrl nodes to be consistent with
other SoCs.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

All current Armada XP SoCs have their pin controller at 0x18000/0x38.
Move the common properties of pinctrl nodes to armada-xp.dtsi to allow
to share pinctrl settings later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-By: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The DIR665 has an 8 port Ethernet Switch, a Marvell mv88e6171. Add a
DSA node in DT, to instantiate DSA support for the 4 back panel ports,
the Internet port, and the port to the CPU which is connected to eth0.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414793613-11798-3-git-send-email-andrew@lunn.chSigned-off-by: Jason Cooper <jason@lakedaemon.net>

Add a device tree description of the DLINK DIR665 wireless access
point. The support for the 88E6171 switch will be added in a later
patch.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414793613-11798-2-git-send-email-andrew@lunn.chSigned-off-by: Jason Cooper <jason@lakedaemon.net>

NETGEAR ReadyNAS 2120 supports its four main SATA disks via 2
Marvell 88SE9170 SATA controllers connected on the PCIe bus
of the the SoC. The two eSATA ports available at the rear of
the device are handled by the native SATA controller of the
Armada XP SoC powering the NAS. This patch enables the SoC
SATA controller in the .dts file to make those two rear ports
available.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/f3876c7a9ef11eb758b9df18c671ee740b8be614.1414250947.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

Now that the timer and watchdog drivers support the Armada 375 usage of
the reference clock, we can enable it in the devicetree.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1414248522-16055-5-git-send-email-ezequiel.garcia@free-electrons.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

On NETGEAR ReadyNAS 102, the two disks are connected to the external
Marvell 88SE9170 SATA Controller connected to the PCIe bus. The rear
eSATA port is connected to the native Armada 370 SATA controller.

This patch updates the comments in .dts file wrt SATA interfaces and
reduces the number of ports for native Armada 370 interface from 2
to 1.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/4af680f9a68281755e31df2491f0590046138230.1414185031.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

When writing initial .dts file for NETGEAR ReadyNAS 102, I put the wrong color
for backup and SATA leds (green instead of blue for all three).
Reported-by: Johan Kristell <johan.kristell@gmail.com>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/4eb4049d934a3a8fe9f7235dafb6842422792566.1414185031.git.arno@natisbad.orgSigned-off-by: Jason Cooper <jason@lakedaemon.net>

The L2 cache controller on the Armada 370 and Armada XP SoCs is a
unified cache. Moreover, the Aurora cache controller is compatible
with the L2x0 cache controller: the "cache-unified" property is
required by its binding.

This patch fixes the Aurora L2 cache node for the Armada 370 and
Armada XP SoCs by adding this property.
Reported-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1412588276-4514-1-git-send-email-gregory.clement@free-electrons.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

Pull ARM SoC fixes from Olof Johansson:
 "A batch of fixes that have come in during the merge window.

  Some of them are defconfig updates for things that have now landed,
  some errata additions and a few general scattered fixes.

  There's also a qcom DT update that adds support for SATA on AP148, and
  basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
  isolated enough that we could merge it even if it's late"

* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: corrected bcm2835 search
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148
  MAINTAINERS: Update Santosh Shilimkar's email id
  ARM: sunxi_defconfig: enable CONFIG_REGULATOR
  ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
  ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
  ARM: exynos_defconfig: enable USB gadget support
  ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
  ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
  ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
  ARM: SAMSUNG: Restore Samsung PM Debug functionality
  ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
  ARM: exynos_defconfig: Enable SBS battery support
  ARM: exynos_defconfig: Enable Control Groups support
  ARM: exynos_defconfig: Enable Atmel maXTouch support
  ARM: exynos_defconfig: Enable MAX77802

Pull audit updates from Eric Paris:
 "So this change across a whole bunch of arches really solves one basic
  problem.  We want to audit when seccomp is killing a process.  seccomp
  hooks in before the audit syscall entry code.  audit_syscall_entry
  took as an argument the arch of the given syscall.  Since the arch is
  part of what makes a syscall number meaningful it's an important part
  of the record, but it isn't available when seccomp shoots the
  syscall...

  For most arch's we have a better way to get the arch (syscall_get_arch)
  So the solution was two fold: Implement syscall_get_arch() everywhere
  there is audit which didn't have it.  Use syscall_get_arch() in the
  seccomp audit code.  Having syscall_get_arch() everywhere meant it was
  a useless flag on the stack and we could get rid of it for the typical
  syscall entry.

  The other changes inside the audit system aren't grand, fixed some
  records that had invalid spaces.  Better locking around the task comm
  field.  Removing some dead functions and structs.  Make some things
  static.  Really minor stuff"

* git://git.infradead.org/users/eparis/audit: (31 commits)
  audit: rename audit_log_remove_rule to disambiguate for trees
  audit: cull redundancy in audit_rule_change
  audit: WARN if audit_rule_change called illegally
  audit: put rule existence check in canonical order
  next: openrisc: Fix build
  audit: get comm using lock to avoid race in string printing
  audit: remove open_arg() function that is never used
  audit: correct AUDIT_GET_FEATURE return message type
  audit: set nlmsg_len for multicast messages.
  audit: use union for audit_field values since they are mutually exclusive
  audit: invalid op= values for rules
  audit: use atomic_t to simplify audit_serial()
  kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
  audit: reduce scope of audit_log_fcaps
  audit: reduce scope of audit_net_id
  audit: arm64: Remove the audit arch argument to audit_syscall_entry
  arm64: audit: Add audit hook in syscall_trace_enter/exit()
  audit: x86: drop arch from __audit_syscall_entry() interface
  sparc: implement is_32bit_task
  sparc: properly conditionalize use of TIF_32BIT
  ...

Merge tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into fixes

Merge "qcom DT changes for v3.18-3" from Kumar Gala:

Qualcomm ARM Based Device Tree Updates for v3.18-3

* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148

* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
  ARM: dts: qcom: add CM-QS600 board
  ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
  ARM: dts: qcom: Add SATA support on IPQ8064/AP148

Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes

Pull more fixes from Kukjin Kim:

2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
  and exynos5420-arndale-octa boards, because the USB dwc3 controller
  will not work properly without dr_mode as host on above boards if
  the USB host and gadget are enabled in kernel configuration both.

* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
  ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>

Corrected bcm2835 maintainer info by using N: to specify any files with
bcm2835 in are directed to the proper maintainer.
Also corrected minor mispelling of ARCHITECTURE in 2 comment locations.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull ntb (non-transparent bridge) updates from Jon Mason:
 "Add support for Haswell NTB split BARs, a debugfs entry for basic
  debugging info, and some code clean-ups"

* tag 'ntb-3.18' of git://github.com/jonmason/ntb:
  ntb: Adding split BAR support for Haswell platforms
  ntb: use errata flag set via DID to implement workaround
  ntb: conslidate reading of PPD to move platform detection earlier
  ntb: move platform detection to separate function
  NTB: debugfs device entry

Pull i2c updates from Wolfram Sang:
 "Highlights from the I2C subsystem for 3.18:

   - new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.

   - designware driver gained AMD support, exynos gained exynos7 support

  The rest is usual driver stuff.  Hopefully no lowlights this time"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i801: Add Device IDs for Intel Sunrise Point PCH
  i2c: hix5hd2: add i2c controller driver
  i2c-imx: Disable the clock on probe failure
  i2c: designware: Add support for AMD I2C controller
  i2c: designware: Rework probe() to get clock a bit later
  i2c: designware: Default to fast mode in case of ACPI
  i2c: axxia: Add I2C driver for AXM55xx
  i2c: exynos: add support for HSI2C module on Exynos7
  i2c: mxs: detect No Slave Ack on SELECT in PIO mode
  i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
  i2c: cros-ec-tunnel: Add of match table
  i2c: rcar: remove sign-compare flaw
  i2c: ismt: Use minimum descriptor size
  i2c: imx: Add arbitration lost check
  i2c: rk3x: Remove unlikely() annotations
  i2c: rcar: check for no IRQ in rcar_i2c_irq()
  i2c: rcar: make rcar_i2c_prepare_msg() *void*
  i2c: rcar: simplify check for last message
  i2c: designware: add support of platform data to set I2C mode
  i2c: designware: add support of I2C standard mode

Pull sound fixes from Takashi Iwai:
 "Here are a collection of small fixes after 3.18 merge.

  The urgent one is the fix for kernel panics with linked PCM substream
  triggered by the recent nonatomic PCM ops support.  Other two fixes
  (emu10k1 and bebob) are stable fixes, and one easy PCI ID addition for
  a new Intel HD-audio controller"

* tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda_intel: Add Device IDs for Intel Sunrise Point PCH
  ALSA: emu10k1: Fix deadlock in synth voice lookup
  ALSA: pcm: Fix referred substream in snd_pcm_action_group() unlock loop
  ALSA: bebob: Fix failure to detect source of clock for Terratec Phase 88

Pull second round of input updates from Dmitry Torokhov:
 "Mostly simple bug fixes, although we do have one brand new driver for
  Microchip AR1021 i2c touchscreen.

  Also there is the change to stop trying to use i8042 active
  multiplexing by default (it is still possible to activate it via
  i8042.nomux=0 on boxes that implement it)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xpad - add Thrustmaster as Xbox 360 controller vendor
  Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
  Input: max77693-haptic - fix state check in imax77693_haptic_disable()
  Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
  Input: alps - fix v4 button press recognition
  Input: i8042 - disable active multiplexing by default
  Input: i8042 - add noloop quirk for Asus X750LN
  Input: synaptics - gate forcepad support by DMI check
  Input: Add Microchip AR1021 i2c touchscreen
  Input: cros_ec_keyb - add of match table
  Input: serio - avoid negative serio device numbers
  Input: avoid negative input device numbers
  Input: automatically set EV_ABS bit in input_set_abs_params
  Input: adp5588-keys - cancel workqueue in failure path
  Input: opencores-kbd - switch to using managed resources
  Input: evdev - fix EVIOCG{type} ioctl