commit cda57b1b upstream.

This device loses blocks, often the partition table area, on trim.
Disable TRIM.
http://pcengines.ch/msata16a.htmSigned-off-by: Arne Fitzenreiter <arne_f@ipfire.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 71d126fd upstream.

Some devices lose data on TRIM whether queued or not.  This patch adds
a horkage to disable TRIM.

tj: Collapsed unnecessary if() nesting.
Signed-off-by: Arne Fitzenreiter <arne_f@ipfire.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
[bwh: Backported to 3.2:
 - Adjust context
 - Drop change to show_ata_dev_trim()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 08c85d2a upstream.

Enabling AA on HP 250GB SATA disk VB0250EAVER causes errors:

[    3.788362] ata3.00: failed to enable AA (error_mask=0x1)
[    3.789243] ata3.00: failed to enable AA (error_mask=0x1)

Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk.

tj: Collected FPDMA_AA entries and updated comment.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 945b4744 upstream.

This commit adds the necessary quirk to make the Marvell 4140 SATA PMP
work properly. This PMP doesn't like SRST on port number 4 (the host
port) so this commit marks this port as not supporting SRST.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4fabb594 upstream.

Fixes: 3e0249f9 ("RDS/IB: add refcount tracking to struct rds_ib_device")

There lacks a dropping on rds_ib_device.refcount in case rds_ib_alloc_fmr
failed(mr pool running out). this lead to the refcount overflow.

A complain in line 117(see following) is seen. From vmcore:
s_ib_rdma_mr_pool_depleted is 2147485544 and rds_ibdev->refcount is -2147475448.
That is the evidence the mr pool is used up. so rds_ib_alloc_fmr is very likely
to return ERR_PTR(-EAGAIN).

115 void rds_ib_dev_put(struct rds_ib_device *rds_ibdev)
116 {
117         BUG_ON(atomic_read(&rds_ibdev->refcount) <= 0);
118         if (atomic_dec_and_test(&rds_ibdev->refcount))
119                 queue_work(rds_wq, &rds_ibdev->free_work);
120 }

fix is to drop refcount when rds_ib_alloc_fmr failed.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit ed958762 upstream.

Using the clone ioctl (or extent_same ioctl, which calls the same extent
cloning function as well) we end up allowing copy an inline extent from
the source file into a non-zero offset of the destination file. This is
something not expected and that the btrfs code is not prepared to deal
with - all inline extents must be at a file offset equals to 0.

For example, the following excerpt of a test case for fstests triggers
a crash/BUG_ON() on a write operation after an inline extent is cloned
into a non-zero offset:

  _scratch_mkfs >>$seqres.full 2>&1
  _scratch_mount

  # Create our test files. File foo has the same 2K of data at offset 4K
  # as file bar has at its offset 0.
  $XFS_IO_PROG -f -s -c "pwrite -S 0xaa 0 4K" \
      -c "pwrite -S 0xbb 4k 2K" \
      -c "pwrite -S 0xcc 8K 4K" \
      $SCRATCH_MNT/foo | _filter_xfs_io

  # File bar consists of a single inline extent (2K size).
  $XFS_IO_PROG -f -s -c "pwrite -S 0xbb 0 2K" \
     $SCRATCH_MNT/bar | _filter_xfs_io

  # Now call the clone ioctl to clone the extent of file bar into file
  # foo at its offset 4K. This made file foo have an inline extent at
  # offset 4K, something which the btrfs code can not deal with in future
  # IO operations because all inline extents are supposed to start at an
  # offset of 0, resulting in all sorts of chaos.
  # So here we validate that clone ioctl returns an EOPNOTSUPP, which is
  # what it returns for other cases dealing with inlined extents.
  $CLONER_PROG -s 0 -d $((4 * 1024)) -l $((2 * 1024)) \
      $SCRATCH_MNT/bar $SCRATCH_MNT/foo

  # Because of the inline extent at offset 4K, the following write made
  # the kernel crash with a BUG_ON().
  $XFS_IO_PROG -c "pwrite -S 0xdd 6K 2K" $SCRATCH_MNT/foo | _filter_xfs_io

  status=0
  exit

The stack trace of the BUG_ON() triggered by the last write is:

  [152154.035903] ------------[ cut here ]------------
  [152154.036424] kernel BUG at mm/page-writeback.c:2286!
  [152154.036424] invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
  [152154.036424] Modules linked in: btrfs dm_flakey dm_mod crc32c_generic xor raid6_pq nfsd auth_rpcgss oid_registry nfs_acl nfs lockd grace fscache sunrpc loop fuse parport_pc acpi_cpu$
  [152154.036424] CPU: 2 PID: 17873 Comm: xfs_io Tainted: G        W       4.1.0-rc6-btrfs-next-11+ #2
  [152154.036424] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20150316_085822-nilsson.home.kraxel.org 04/01/2014
  [152154.036424] task: ffff880429f70990 ti: ffff880429efc000 task.ti: ffff880429efc000
  [152154.036424] RIP: 0010:[<ffffffff8111a9d5>]  [<ffffffff8111a9d5>] clear_page_dirty_for_io+0x1e/0x90
  [152154.036424] RSP: 0018:ffff880429effc68  EFLAGS: 00010246
  [152154.036424] RAX: 0200000000000806 RBX: ffffea0006a6d8f0 RCX: 0000000000000001
  [152154.036424] RDX: 0000000000000000 RSI: ffffffff81155d1b RDI: ffffea0006a6d8f0
  [152154.036424] RBP: ffff880429effc78 R08: ffff8801ce389fe0 R09: 0000000000000001
  [152154.036424] R10: 0000000000002000 R11: ffffffffffffffff R12: ffff8800200dce68
  [152154.036424] R13: 0000000000000000 R14: ffff8800200dcc88 R15: ffff8803d5736d80
  [152154.036424] FS:  00007fbf119f6700(0000) GS:ffff88043d280000(0000) knlGS:0000000000000000
  [152154.036424] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  [152154.036424] CR2: 0000000001bdc000 CR3: 00000003aa555000 CR4: 00000000000006e0
  [152154.036424] Stack:
  [152154.036424]  ffff8803d5736d80 0000000000000001 ffff880429effcd8 ffffffffa04e97c1
  [152154.036424]  ffff880429effd68 ffff880429effd60 0000000000000001 ffff8800200dc9c8
  [152154.036424]  0000000000000001 ffff8800200dcc88 0000000000000000 0000000000001000
  [152154.036424] Call Trace:
  [152154.036424]  [<ffffffffa04e97c1>] lock_and_cleanup_extent_if_need+0x147/0x18d [btrfs]
  [152154.036424]  [<ffffffffa04ea82c>] __btrfs_buffered_write+0x245/0x4c8 [btrfs]
  [152154.036424]  [<ffffffffa04ed14b>] ? btrfs_file_write_iter+0x150/0x3e0 [btrfs]
  [152154.036424]  [<ffffffffa04ed15a>] ? btrfs_file_write_iter+0x15f/0x3e0 [btrfs]
  [152154.036424]  [<ffffffffa04ed2c7>] btrfs_file_write_iter+0x2cc/0x3e0 [btrfs]
  [152154.036424]  [<ffffffff81165a4a>] __vfs_write+0x7c/0xa5
  [152154.036424]  [<ffffffff81165f89>] vfs_write+0xa0/0xe4
  [152154.036424]  [<ffffffff81166855>] SyS_pwrite64+0x64/0x82
  [152154.036424]  [<ffffffff81465197>] system_call_fastpath+0x12/0x6f
  [152154.036424] Code: 48 89 c7 e8 0f ff ff ff 5b 41 5c 5d c3 0f 1f 44 00 00 55 48 89 e5 41 54 53 48 89 fb e8 ae ef 00 00 49 89 c4 48 8b 03 a8 01 75 02 <0f> 0b 4d 85 e4 74 59 49 8b 3c 2$
  [152154.036424] RIP  [<ffffffff8111a9d5>] clear_page_dirty_for_io+0x1e/0x90
  [152154.036424]  RSP <ffff880429effc68>
  [152154.242621] ---[ end trace e3d3376b23a57041 ]---

Fix this by returning the error EOPNOTSUPP if an attempt to copy an
inline extent into a non-zero offset happens, just like what is done for
other scenarios that would require copying/splitting inline extents,
which were introduced by the following commits:

   00fdf13a ("Btrfs: fix a crash of clone with inline extents's split")
   3f9e3df8 ("btrfs: replace error code from btrfs_drop_extents")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
[bwh: Backported to 3.2: test new_key.offset as last_dest_end isn't defined
 in this function]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit e47994dd upstream.

The sfpc inline assembly within execve_tail() may incorrectly set bits
28-31 of the sfpc instruction to a value which is not zero.
These bits however are currently unused and therefore should be zero
so we won't get surprised if these bits will be used in the future.

Therefore remove the second operand from the inline assembly.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0a73d0a2 upstream.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2c17d27c upstream.

Incoming packet should be either in backlog queue or
in RCU read-side section. Otherwise, the final sequence of
flush_backlog() and synchronize_net() may miss packets
that can run without device reference:

CPU 1                  CPU 2
                       skb->dev: no reference
                       process_backlog:__skb_dequeue
                       process_backlog:local_irq_enable

on_each_cpu for
flush_backlog =>       IPI(hardirq): flush_backlog
                       - packet not found in backlog

                       CPU delayed ...
synchronize_net
- no ongoing RCU
read-side sections

netdev_run_todo,
rcu_barrier: no
ongoing callbacks
                       __netif_receive_skb_core:rcu_read_lock
                       - too late
free dev
                       process packet for freed dev

Fixes: 6e583ce5 ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2:
 - Adjust context
 - No need to rename the label in __netif_receive_skb()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit e9e4dd32 upstream.

commit 381c759d ("ipv4: Avoid crashing in ip_error")
fixes a problem where processed packet comes from device
with destroyed inetdev (dev->ip_ptr). This is not expected
because inetdev_destroy is called in NETDEV_UNREGISTER
phase and packets should not be processed after
dev_close_many() and synchronize_net(). Above fix is still
required because inetdev_destroy can be called for other
reasons. But it shows the real problem: backlog can keep
packets for long time and they do not hold reference to
device. Such packets are then delivered to upper levels
at the same time when device is unregistered.
Calling flush_backlog after NETDEV_UNREGISTER_FINAL still
accounts all packets from backlog but before that some packets
continue to be delivered to upper levels long after the
synchronize_net call which is supposed to wait the last
ones. Also, as Eric pointed out, processed packets, mostly
from other devices, can continue to add new packets to backlog.

Fix the problem by moving flush_backlog early, after the
device driver is stopped and before the synchronize_net() call.
Then use netif_running check to make sure we do not add more
packets to backlog. We have to do it in enqueue_to_backlog
context when the local IRQ is disabled. As result, after the
flush_backlog and synchronize_net sequence all packets
should be accounted.

Thanks to Eric W. Biederman for the test script and his
valuable feedback!
Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Fixes: 6e583ce5 ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 6b7339f4 upstream.

Reading page fault handler code I've noticed that under right
circumstances kernel would map anonymous pages into file mappings: if
the VMA doesn't have vm_ops->fault() and the VMA wasn't fully populated
on ->mmap(), kernel would handle page fault to not populated pte with
do_anonymous_page().

Let's change page fault handler to use do_anonymous_page() only on
anonymous VMA (->vm_ops == NULL) and make sure that the VMA is not
shared.

For file mappings without vm_ops->fault() or shred VMA without vm_ops,
page fault on pte_none() entry would lead to SIGBUS.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4f7d2cdf upstream.

Jason Gunthorpe reported that since commit c02db8c6 ("rtnetlink: make
SR-IOV VF interface symmetric"), we don't verify IFLA_VF_INFO attributes
anymore with respect to their policy, that is, ifla_vfinfo_policy[].

Before, they were part of ifla_policy[], but they have been nested since
placed under IFLA_VFINFO_LIST, that contains the attribute IFLA_VF_INFO,
which is another nested attribute for the actual VF attributes such as
IFLA_VF_MAC, IFLA_VF_VLAN, etc.

Despite the policy being split out from ifla_policy[] in this commit,
it's never applied anywhere. nla_for_each_nested() only does basic nla_ok()
testing for struct nlattr, but it doesn't know about the data context and
their requirements.

Fix, on top of Jason's initial work, does 1) parsing of the attributes
with the right policy, and 2) using the resulting parsed attribute table
from 1) instead of the nla_for_each_nested() loop (just like we used to
do when still part of ifla_policy[]).

Reference: http://thread.gmane.org/gmane.linux.network/368913
Fixes: c02db8c6 ("rtnetlink: make SR-IOV VF interface symmetric")
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Rony Efraim <ronye@mellanox.com>
Cc: Vlad Zolotarov <vladz@cloudius-systems.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2:
 - Drop unsupported attributes
 - Use ndo_set_vf_tx_rate operation, not ndo_set_vf_rate]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 01447e9f upstream.

legacy setcrtc ioctl does take a 32 bit value which might indeed
overflow

the checks of crtc_req->x > INT_MAX and crtc_req->y > INT_MAX aren't
needed any more with this

v2: -polish the annotation according to Daniel's comment

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Zhao Junwang <zhjwpku@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 1d97e915 upstream.

The crtc x/y panning coordinates are stored as signed integers
internally. The user provides them as unsigned, so we should check
that the user provided values actually fit in the internal datatypes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f9c87a6f upstream.

If the kernel is compiled with gcc 5.1 and the XZ compression option
the decompress_kernel function calls _sclp_print_early in 64-bit mode
while the content of the upper register half of %r6 is non-zero.
This causes a specification exception on the servc instruction in
_sclp_servc.

The _sclp_print_early function saves and restores the upper registers
halves but it fails to clear them for the 31-bit code of the mini sclp
driver.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 1c751879 upstream.

Allocate memory using GFP_NOIO when deleting a btree.  dm_btree_del()
can be called via an ioctl and we don't want to recurse into the FS or
block layer.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f98a7aa8 upstream.

Add the USB serial console device ID for Aruba Networks 7xxx series
controllers which have a USB port for their serial console.
Signed-off-by: Peter Sanford <peter@sanford.io>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit a822c83e upstream.

Given the pool's cell_sort_array holds 8192 pointers it triggers an
order 5 allocation via kmalloc.  This order 5 allocation is prone to
failure as system memory gets more fragmented over time.

Fix this by allocating the cell_sort_array using vmalloc.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[bwh: Backported to 3.2: make a similar change in prison_{create,destroy}()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4c7e3093 upstream.

redistribute3() shares entries out across 3 nodes.  Some entries were
being moved the wrong way, breaking the ordering.  This manifested as a
BUG() in dm-btree-remove.c:shift() when entries were removed from the
btree.

For additional context see:
https://www.redhat.com/archives/dm-devel/2015-May/msg00113.htmlSigned-off-by: Dennis Yang <shinrairis@gmail.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 7444a072 upstream.

ext4_free_blocks is looping around the allocation request and mimics
__GFP_NOFAIL behavior without any allocation fallback strategy. Let's
remove the open coded loop and replace it with __GFP_NOFAIL. Without the
flag the allocator has no way to find out never-fail requirement and
cannot help in any way.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[bwh: Backported to 3.2:
 - Adjust context
 - s/ext4_free_data_cachep/ext4_free_ext_cachep/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit a84b69cb upstream.

If we'd already sent a request and decide to abort it, we *must*
issue TFLUSH properly and not just blindly reuse the tag, or
we'll get seriously screwed when response eventually arrives
and we confuse it for response to later request that had reused
the same tag.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit db138562 upstream.

Legacy NMI watchdog didn't work after migration/resume, because
vapics_in_nmi_mode was left at 0.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.2:
 - Adjust context
 - s/kvm_apic_get_reg/apic_get_reg/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 42720138 upstream.

Writes were a bit racy, but hard to turn into a bug at the same time.
(Particularly because modern Linux doesn't use this feature anymore.)
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[Actually the next patch makes it much, much easier to trigger the race
 so I'm including this one for stable@ as well. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit dd302b59 upstream.

br_nf_dev_queue_xmit must free skb in its error path.
NF_DROP is misleading -- its an okfn, not a netfilter hook.

Fixes: 462fb2af ("bridge : Sanitize skb before it enters the IP stack")
Fixes: efb6de9b ("netfilter: bridge: forward IPv6 fragmented packets")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[bwh: Backported to 3.2:
 - Adjust filename
 - Drop IPv6 changes]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit c45653c3 upstream.

Switch ext4 to using sb_getblk_gfp with GFP_NOFS added to fix possible
deadlocks in the page writeback path.
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit bd7ade3c upstream.

sb_getblk() is used during ext4 (and possibly other FSes) writeback
paths. Sometimes such path require allocating memory and guaranteeing
that such allocation won't block. Currently, however, there is no way
to provide user flags for sb_getblk which could lead to deadlocks.

This patch implements a sb_getblk_gfp with the only difference it can
accept user-provided GFP flags.
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 3b5e6454 upstream.

A buffer cache is allocated from movable area because it is referred
for a while and released soon.  But some filesystems are taking buffer
cache for a long time and it can disturb page migration.

New APIs are introduced to allocate buffer cache with user specific
flag.  *_gfp APIs are for user want to set page allocation flag for
page cache allocation.  And *_unmovable APIs are for the user wants to
allocate page cache from non-movable area.
Signed-off-by: Gioh Kim <gioh.kim@lge.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
[bwh: Prerequisite for "bufferhead: Add _gfp version for sb_getblk()".
 Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit c04be184 upstream.

ACPICA commit 90f5332a15e9d9ba83831ca700b2b9f708274658

This patch adds a new FACS initialization flag for acpi_tb_initialize().
acpi_enable_subsystem() might be invoked several times in OS bootup process,
and we don't want FACS initialization to be invoked twice. Lv Zheng.

Link: https://github.com/acpica/acpica/commit/90f5332aSigned-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0689a86a upstream.

The Steinberg MI2 and MI4 interfaces are compatible with the USB class
audio spec, but the MIDI part of the devices is reported as a vendor
specific interface.

This patch adds entries to quirks-table.h to recognize the MIDI
endpoints. Audio functionality was already working and is unaffected by
this change.
Signed-off-by: Dominic Sacré <dominic.sacre@gmx.de>
Signed-off-by: Albert Huitsing <albert@huitsing.nl>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0ad0b325 upstream.

fc->release is called from fuse_conn_put() which was used in the error
cleanup before fc->release was initialized.

[Jeremiah Mahler <jmmahler@gmail.com>: assign fc->release after calling
fuse_conn_init(fc) instead of before.]
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Fixes: a325f9b9 ("fuse: update fuse_conn_init() and separate out fuse_conn_kill()")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 82cd003a upstream.

struct crush_bucket_tree::num_nodes is u8, so ceph_decode_8_safe()
should be used.  -Wconversion catches this, but I guess it went
unnoticed in all the noise it spews.  The actual problem (at least for
common crushmaps) isn't the u32 -> u8 truncation though - it's the
advancement by 4 bytes instead of 1 in the crushmap buffer.

Fixes: http://tracker.ceph.com/issues/2759Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit ae9d8f17 upstream.

While the inode cache caching kthread is calling btrfs_unpin_free_ino(),
we could have a concurrent call to btrfs_return_ino() that adds a new
entry to the root's free space cache of pinned inodes. This concurrent
call does not acquire the fs_info->commit_root_sem before adding a new
entry if the caching state is BTRFS_CACHE_FINISHED, which is a problem
because the caching kthread calls btrfs_unpin_free_ino() after setting
the caching state to BTRFS_CACHE_FINISHED and therefore races with
the task calling btrfs_return_ino(), which is adding a new entry, while
the former (caching kthread) is navigating the cache's rbtree, removing
and freeing nodes from the cache's rbtree without acquiring the spinlock
that protects the rbtree.

This race resulted in memory corruption due to double free of struct
btrfs_free_space objects because both tasks can end up doing freeing the
same objects. Note that adding a new entry can result in merging it with
other entries in the cache, in which case those entries are freed.
This is particularly important as btrfs_free_space structures are also
used for the block group free space caches.

This memory corruption can be detected by a debugging kernel, which
reports it with the following trace:

[132408.501148] slab error in verify_redzone_free(): cache `btrfs_free_space': double free detected
[132408.505075] CPU: 15 PID: 12248 Comm: btrfs-ino-cache Tainted: G        W       4.1.0-rc5-btrfs-next-10+ #1
[132408.505075] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.8.1-0-g4adadbd-20150316_085822-nilsson.home.kraxel.org 04/01/2014
[132408.505075]  ffff880023e7d320 ffff880163d73cd8 ffffffff8145eec7 ffffffff81095dce
[132408.505075]  ffff880009735d40 ffff880163d73ce8 ffffffff81154e1e ffff880163d73d68
[132408.505075]  ffffffff81155733 ffffffffa054a95a ffff8801b6099f00 ffffffffa0505b5f
[132408.505075] Call Trace:
[132408.505075]  [<ffffffff8145eec7>] dump_stack+0x4f/0x7b
[132408.505075]  [<ffffffff81095dce>] ? console_unlock+0x356/0x3a2
[132408.505075]  [<ffffffff81154e1e>] __slab_error.isra.28+0x25/0x36
[132408.505075]  [<ffffffff81155733>] __cache_free+0xe2/0x4b6
[132408.505075]  [<ffffffffa054a95a>] ? __btrfs_add_free_space+0x2f0/0x343 [btrfs]
[132408.505075]  [<ffffffffa0505b5f>] ? btrfs_unpin_free_ino+0x8e/0x99 [btrfs]
[132408.505075]  [<ffffffff810f3b30>] ? time_hardirqs_off+0x15/0x28
[132408.505075]  [<ffffffff81084d42>] ? trace_hardirqs_off+0xd/0xf
[132408.505075]  [<ffffffff811563a1>] ? kfree+0xb6/0x14e
[132408.505075]  [<ffffffff811563d0>] kfree+0xe5/0x14e
[132408.505075]  [<ffffffffa0505b5f>] btrfs_unpin_free_ino+0x8e/0x99 [btrfs]
[132408.505075]  [<ffffffffa0505e08>] caching_kthread+0x29e/0x2d9 [btrfs]
[132408.505075]  [<ffffffffa0505b6a>] ? btrfs_unpin_free_ino+0x99/0x99 [btrfs]
[132408.505075]  [<ffffffff8106698f>] kthread+0xef/0xf7
[132408.505075]  [<ffffffff810f3b08>] ? time_hardirqs_on+0x15/0x28
[132408.505075]  [<ffffffff810668a0>] ? __kthread_parkme+0xad/0xad
[132408.505075]  [<ffffffff814653d2>] ret_from_fork+0x42/0x70
[132408.505075]  [<ffffffff810668a0>] ? __kthread_parkme+0xad/0xad
[132408.505075] ffff880023e7d320: redzone 1:0x9f911029d74e35b, redzone 2:0x9f911029d74e35b.
[132409.501654] slab: double free detected in cache 'btrfs_free_space', objp ffff880023e7d320
[132409.503355] ------------[ cut here ]------------
[132409.504241] kernel BUG at mm/slab.c:2571!

Therefore fix this by having btrfs_unpin_free_ino() acquire the lock
that protects the rbtree while doing the searches and removing entries.

Fixes: 1c70d8fb ("Btrfs: fix inode caching vs tree log")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit c3f4a168 upstream.

The free space entries are allocated using kmem_cache_zalloc(),
through __btrfs_add_free_space(), therefore we should use
kmem_cache_free() and not kfree() to avoid any confusion and
any potential problem. Looking at the kfree() definition at
mm/slab.c it has the following comment:

  /*
   * (...)
   *
   * Don't free memory not originally allocated by kmalloc()
   * or you will run into trouble.
   */

So better be safe and use kmem_cache_free().
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 8b572a42 upstream.

In needs_ilk_vtd_wa(), we pass in the GPU device but compared it against
the ids for the mobile GPU and the mobile host bridge. That latter is
impossible and so likely was just a typo for the desktop GPU device id
(which is also buggy).

Fixes commit da88a5f7
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Wed Feb 13 09:31:53 2013 +0000

    drm/i915: Disable WC PTE updates to w/a buggy IOMMU on ILK
Reported-by: Ting-Wei Lan <lantw44@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91127
References: https://bugzilla.freedesktop.org/show_bug.cgi?id=60391Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2528a8b8 upstream.

bitmap_parselist("", &mask, nmaskbits) will erroneously set bit zero in
the mask.  The same bug is visible in cpumask_parselist() since it is
layered on top of the bitmask code, e.g.  if you boot with "isolcpus=",
you will actually end up with cpu zero isolated.

The bug was introduced in commit 4b060420 ("bitmap, irq: add
smp_affinity_list interface to /proc/irq") when bitmap_parselist() was
generalized to support userspace as well as kernelspace.

Fixes: 4b060420 ("bitmap, irq: add smp_affinity_list interface to /proc/irq")
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 6b88f44e upstream.

While debugging a WARN_ON() for filtering, I found that it is possible
for the filter string to be referenced after its end. With the filter:

 # echo '>' > /sys/kernel/debug/events/ext4/ext4_truncate_exit/filter

The filter_parse() function can call infix_get_op() which calls
infix_advance() that updates the infix filter pointers for the cnt
and tail without checking if the filter is already at the end, which
will put the cnt to zero and the tail beyond the end. The loop then calls
infix_next() that has

	ps->infix.cnt--;
	return ps->infix.string[ps->infix.tail++];

The cnt will now be below zero, and the tail that is returned is
already passed the end of the filter string. So far the allocation
of the filter string usually has some buffer that is zeroed out, but
if the filter string is of the exact size of the allocated buffer
there's no guarantee that the charater after the nul terminating
character will be zero.

Luckily, only root can write to the filter.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit b4875bbe upstream.

When testing the fix for the trace filter, I could not come up with
a scenario where the operand count goes below zero, so I added a
WARN_ON_ONCE(cnt < 0) to the logic. But there is legitimate case
that it can happen (although the filter would be wrong).

 # echo '>' > /sys/kernel/debug/events/ext4/ext4_truncate_exit/filter

That is, a single operation without any operands will hit the path
where the WARN_ON_ONCE() can trigger. Although this is harmless,
and the filter is reported as a error. But instead of spitting out
a warning to the kernel dmesg, just fail nicely and report it via
the proper channels.

Link: http://lkml.kernel.org/r/558C6082.90608@oracle.comReported-by: Vince Weaver <vincent.weaver@maine.edu>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit b8830a4e upstream.

This commit fix kernel crash when probing for rfkill devices in dell-laptop
driver failed. Function free_page() was incorrectly used on struct page *
instead of virtual address of SMI buffer.

This commit also simplify allocating page for SMI buffer by using
__get_free_page() function instead of sequential call of functions
alloc_page() and page_address().
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit c5f3b1a5 upstream.

The kmemleak scanning thread can run for minutes.  Callbacks like
kmemleak_free() are allowed during this time, the race being taken care
of by the object->lock spinlock.  Such lock also prevents a memory block
from being freed or unmapped while it is being scanned by blocking the
kmemleak_free() -> ...  -> __delete_object() function until the lock is
released in scan_object().

When a kmemleak error occurs (e.g.  it fails to allocate its metadata),
kmemleak_enabled is set and __delete_object() is no longer called on
freed objects.  If kmemleak_scan is running at the same time,
kmemleak_free() no longer waits for the object scanning to complete,
allowing the corresponding memory block to be freed or unmapped (in the
case of vfree()).  This leads to kmemleak_scan potentially triggering a
page fault.

This patch separates the kmemleak_free() enabling/disabling from the
overall kmemleak_enabled nob so that we can defer the disabling of the
object freeing tracking until the scanning thread completed.  The
kmemleak_free_part() is deliberately ignored by this patch since this is
only called during boot before the scanning thread started.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Vignesh Radhakrishnan <vigneshr@codeaurora.org>
Tested-by: Vignesh Radhakrishnan <vigneshr@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2:
 - Adjust context
 - Drop changes to kmemleak_free_percpu()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f1590670 upstream.

Current implementation of descriptor init procedure only takes
care about setting/clearing ownership flag in "des0"/"des1"
fields while it is perfectly possible to get unexpected bits
set because of the following factors:

 [1] On driver probe underlying memory allocated with
     dma_alloc_coherent() might not be zeroed and so
     it will be filled with garbage.

 [2] During driver operation some bits could be set by SD/MMC
     controller (for example error flags etc).

And unexpected and/or randomly set flags in "des0"/"des1"
fields may lead to unpredictable behavior of GMAC DMA block.

This change addresses both items above with:

 [1] Use of dma_zalloc_coherent() instead of simple
     dma_alloc_coherent() to make sure allocated memory is
     zeroed. That shouldn't affect performance because
     this allocation only happens once on driver probe.

 [2] Do explicit zeroing of both "des0" and "des1" fields
     of all buffer descriptors during initialization of
     DMA transfer.

And while at it fixed identation of dma_free_coherent()
counterpart as well.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2:
 - Adjust context, indentation
 - Normal and extended descriptors are allocated in the same place here]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>