DEV_STATE_QUIESCE is used to stop all IO on a busy subchannel.
This patch fixes the following problems related to the QUIESCE
state:

* Fix a potential race condition which could occur when the
resulting state was DEV_STATE_OFFLINE.

* Add missing locking around cio_disable_subchannel,
ccw_device_cancel_halt_clear and the cdev's handler.

* Loop until we know for sure that the subchannel is disabled.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The function ccw_device_unregister has to ensure to remove
all references obtained by device_add and device_initialize.
Unfortunately it gets called for devices which are
1) uninitialized, 2) initialized but unregistered, and
3) registered devices. To distinguish 1) and 2) this patch
introduces a new flag "initialized", which is 1 as long as we
hold the initial device reference.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

We used to maintain a "registered" flag in our ccw_device_private
structure. This patch removes the "registered" flag and converts
all users of it to device_is_registered which has the exact same
meaning.

Note: The usage the atomic operation test_and_clear_bit is replaced
by the non-atomic if (device_is_registered()) device_del(). This
will not do harm, since we serialize calls to ccw_device_unregister
with a single-threaded workqueue.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

An Unconditional Reserve + Release operation (steal lock) for a
boxed device may fail when encountering special error cases
(e.g. unit checks or path errors). Fix this by using the more
robust ccw_request infrastructure for performing the steal lock
CCW program.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Set-pgid operations fail for some device types under z/VM for which
the hypervisor has already set the pgid. Also reserved devices or
changed pgids are not correctly recognized. Fix these problems by
using a combination of sense-pgid and set-pgid and by also accepting
pre-defined pgid settings.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Split setting (driver wants feature enabled) and status (feature
setup was successful) for PGID related ccw device features so that
setup errors can be detected. Previously, incorrectly handled setup
errors could in rare cases lead to erratic I/O behavior and
permanently unusuable devices.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

After changing all internal I/O functions to use the newly introduced
ccw request infrastructure, retries are handled automatically after a
clear operation. Therefore remove the internal retry flag and
associated code.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Accept a request for setting a not-operational device offline.
This way, users can remove devices from Linux which would otherwise
remain unusable until reboot.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Use the newly introduced ccw request infrastructure to implement
pgid related operations: sense pgid, set pgid and disband pg.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Use the newly introduced ccw request infrastructure to implement
the sense id operation.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Reduce code duplication by introducing a central infrastructure to
perform an internal I/O operation on a CCW device.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Remove the call to BUG() for situations which are unexpected
but do not cause actual problems.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Device recognition needs to be started with the ccw device lock
held to prevent race conditions between I/O starting and interrupt
reception.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Handle verification errors consistently through the existing
callback ccw_device_done to reduce cleanup code duplication.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Remove the return code from ccw_device_recognition and handle
recognition errors through the existing callback
ccw_device_recog_done to reduce cleanup code duplication.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Print a warning message in case a ccw device enters boxed or
not operational state during online/offline processing.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Introduce a central mechanism for performing delayed ccw device work
to ensure that different types of work do not overwrite each other.
Prioritization ensures that the most important work is always
performed while less important tasks are either obsoleted or repeated
later.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Ensure that current and future users of sch->work do not overwrite
each other by introducing a single mechanism for delayed subchannel
work.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Change the initiative to update subchannel-ccw device associations
to the subchannel: when there is an indication that the internal
association no longer reflects the current hardware state, mark
each affected subchannel as requiring attention. Once processing
reaches a subchannel, determine the correct association for that
subchannel at that time and perform the necessary device_move
operations.

This change fixes problems with the previous approach which would
leave devices in an inconsistent state when a new hardware change
occurred while a device_move was already scheduled.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

sch_create_and_recog_new_device() associates a parent subchannel
with its ccw device child even though this is already done by
the subsequently called io_subchannel_recog(). Also make sure
io_subchannel_recog() sets the association under lock.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

io_subchannel_probe() frees memory for sch->private which is later
freed again when io_subchannel_remove() is called. Fix this problem
by removing the cleanup in io_subchannel_probe().
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

When the kernel is IPLed without the CLEAR option and switches
to 64-bit, the high-order half of the registers might contain
random values.  This can cause addressing exceptions and the
kernel enters an interrupt loop.

Initialize the high-order half of the general purpose registers
with zeros after switching to 64-bit mode.

Cc: <stable@kernel.org>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Merge branch 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Limit number of per cpu TSC sync messages
  x86: dumpstack, 64-bit: Disable preemption when walking the IRQ/exception stacks
  x86: dumpstack: Clean up the x86_stack_ids[][] initalization and other details
  x86, cpu: mv display_cacheinfo -> cpu_detect_cache_sizes
  x86: Suppress stack overrun message for init_task
  x86: Fix cpu_devs[] initialization in early_cpu_init()
  x86: Remove CPU cache size output for non-Intel too
  x86: Minimise printk spew from per-vendor init code
  x86: Remove the CPU cache size printk's
  cpumask: Avoid cpumask_t in arch/x86/kernel/apic/nmi.c
  x86: Make sure we also print a Code: line for show_regs()

* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, msr, cpumask: Use struct cpumask rather than the deprecated cpumask_t
  x86, cpuid: Simplify the code in cpuid_open
  x86, cpuid: Remove the bkl from cpuid_open()
  x86, msr: Remove the bkl from msr_open()
  x86: AMD Geode LX optimizations
  x86, msr: Unify rdmsr_on_cpus/wrmsr_on_cpus

Merge branch 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Fix a section mismatch in arch/x86/kernel/setup.c
  x86: Fixup last users of irq_chip->typename
  x86: Remove BKL from apm_32
  x86: Remove BKL from microcode
  x86: use kernel_stack_pointer() in kprobes.c
  x86: use kernel_stack_pointer() in kgdb.c
  x86: use kernel_stack_pointer() in dumpstack.c
  x86: use kernel_stack_pointer() in process_32.c

* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  include/linux/compiler-gcc4.h: Fix build bug - gcc-4.0.2 doesn't understand __builtin_object_size
  x86/alternatives: No need for alternatives-asm.h to re-invent stuff already in asm.h
  x86/alternatives: Check replacementlen <= instrlen at build time
  x86, 64-bit: Set data segments to null after switching to 64-bit mode
  x86: Clean up the loadsegment() macro
  x86: Optimize loadsegment()
  x86: Add missing might_fault() checks to copy_{to,from}_user()
  x86-64: __copy_from_user_inatomic() adjustments
  x86: Remove unused thread_return label from switch_to()
  x86, 64-bit: Fix bstep_iret jump
  x86: Don't use the strict copy checks when branch profiling is in use
  x86, 64-bit: Move K8 B step iret fixup to fault entry asm
  x86: Generate cmpxchg build failures
  x86: Add a Kconfig option to turn the copy_from_user warnings into errors
  x86: Turn the copy_from_user check into an (optional) compile time warning
  x86: Use __builtin_memset and __builtin_memcpy for memset/memcpy
  x86: Use __builtin_object_size() to validate the buffer size for copy_from_user()

Merge branch 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
  x86, apic: Enable lapic nmi watchdog on AMD Family 11h
  x86: Remove unnecessary mdelay() from cpu_disable_common()
  x86, ioapic: Document another case when level irq is seen as an edge
  x86, ioapic: Fix the EOI register detection mechanism
  x86, io-apic: Move the effort of clearing remoteIRR explicitly before migrating the irq
  x86: SGI UV: Map low MMR ranges
  x86: apic: Print out SRAT table APIC id in hex
  x86: Re-get cfg_new in case reuse/move irq_desc
  x86: apic: Remove not needed #ifdef
  x86: io-apic: IO-APIC MMIO should not fail on resource insertion
  x86: Remove asm/apicnum.h
  x86: apic: Do not use stacked physid_mask_t
  x86, apic: Get rid of apicid_to_cpu_present assign on 64-bit
  x86, ioapic: Use snrpintf while set names for IO-APIC resourses
  x86, apic: Use PAGE_SIZE instead of numbers
  x86: Remove local_irq_enable()/local_irq_disable() in fixup_irqs()
  x86: Use EOI register in io-apic on intel platforms
  x86: Force irq complete move during cpu offline
  x86: Remove move_cleanup_count from irq_cfg
  x86, intr-remap: Avoid irq_chip mask/unmask in fixup_irqs() for intr-remapping
  ...

Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (35 commits)
  sched, cputime: Introduce thread_group_times()
  sched, cputime: Cleanups related to task_times()
  Revert "sched, x86: Optimize branch hint in __switch_to()"
  sched: Fix isolcpus boot option
  sched: Revert 498657a4
  sched, time: Define nsecs_to_jiffies()
  sched: Remove task_{u,s,g}time()
  sched: Introduce task_times() to replace task_{u,s}time() pair
  sched: Limit the number of scheduler debug messages
  sched.c: Call debug_show_all_locks() when dumping all tasks
  sched, x86: Optimize branch hint in __switch_to()
  sched: Optimize branch hint in context_switch()
  sched: Optimize branch hint in pick_next_task_fair()
  sched_feat_write(): Update ppos instead of file->f_pos
  sched: Sched_rt_periodic_timer vs cpu hotplug
  sched, kvm: Fix race condition involving sched_in_preempt_notifers
  sched: More generic WAKE_AFFINE vs select_idle_sibling()
  sched: Cleanup select_task_rq_fair()
  sched: Fix granularity of task_u/stime()
  sched: Fix/add missing update_rq_clock() calls
  ...

Merge branch 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (470 commits)
  x86: Fix comments of register/stack access functions
  perf tools: Replace %m with %a in sscanf
  hw-breakpoints: Keep track of user disabled breakpoints
  tracing/syscalls: Make syscall events print callbacks static
  tracing: Add DEFINE_EVENT(), DEFINE_SINGLE_EVENT() support to docbook
  perf: Don't free perf_mmap_data until work has been done
  perf_event: Fix compile error
  perf tools: Fix _GNU_SOURCE macro related strndup() build error
  trace_syscalls: Remove unused syscall_name_to_nr()
  trace_syscalls: Simplify syscall profile
  trace_syscalls: Remove duplicate init_enter_##sname()
  trace_syscalls: Add syscall_nr field to struct syscall_metadata
  trace_syscalls: Remove enter_id exit_id
  trace_syscalls: Set event_enter_##sname->data to its metadata
  trace_syscalls: Remove unused event_syscall_enter and event_syscall_exit
  perf_event: Initialize data.period in perf_swevent_hrtimer()
  perf probe: Simplify event naming
  perf probe: Add --list option for listing current probe events
  perf probe: Add argv_split() from lib/argv_split.c
  perf probe: Move probe event utility functions to probe-event.c
  ...

Merge branch 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (40 commits)
  tracing: Separate raw syscall from syscall tracer
  ring-buffer-benchmark: Add parameters to set produce/consumer priorities
  tracing, function tracer: Clean up strstrip() usage
  ring-buffer benchmark: Run producer/consumer threads at nice +19
  tracing: Remove the stale include/trace/power.h
  tracing: Only print objcopy version warning once from recordmcount
  tracing: Prevent build warning: 'ftrace_graph_buf' defined but not used
  ring-buffer: Move access to commit_page up into function used
  tracing: do not disable interrupts for trace_clock_local
  ring-buffer: Add multiple iterations between benchmark timestamps
  kprobes: Sanitize struct kretprobe_instance allocations
  tracing: Fix to use __always_unused attribute
  compiler: Introduce __always_unused
  tracing: Exit with error if a weak function is used in recordmcount.pl
  tracing: Move conditional into update_funcs() in recordmcount.pl
  tracing: Add regex for weak functions in recordmcount.pl
  tracing: Move mcount section search to front of loop in recordmcount.pl
  tracing: Fix objcopy revision check in recordmcount.pl
  tracing: Check absolute path of input file in recordmcount.pl
  tracing: Correct the check for number of arguments in recordmcount.pl
  ...

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tracing: Fix trace_marker output
  tracing: Fix event format export
  tracing: Fix return value of tracing_stats_read()

Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Fix spurious irq seqfile conversion
  genirq: switch /proc/irq/*/spurious to seq_file
  irq: Do not attempt to create subdirectories if /proc/irq/<irq> failed
  irq: Remove unused debug_poll_all_shared_irqs()
  irq: Fix docbook comments
  irq: trivial: Fix typo in comment for #endif

Merge branch 'core-softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  softlockup: Fix hung_task_check_count sysctl

Merge branch 'core-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  signal: Print warning message when dropping signals
  signal: Fix alternate signal stack check

Merge branch 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
  rcu: Make RCU's CPU-stall detector be default
  rcu: Add expedited grace-period support for preemptible RCU
  rcu: Enable fourth level of TREE_RCU hierarchy
  rcu: Rename "quiet" functions
  rcu: Re-arrange code to reduce #ifdef pain
  rcu: Eliminate unneeded function wrapping
  rcu: Fix grace-period-stall bug on large systems with CPU hotplug
  rcu: Eliminate __rcu_pending() false positives
  rcu: Further cleanups of use of lastcomp
  rcu: Simplify association of forced quiescent states with grace periods
  rcu: Accelerate callback processing on CPUs not detecting GP end
  rcu: Mark init-time-only rcu_bootup_announce() as __init
  rcu: Simplify association of quiescent states with grace periods
  rcu: Rename dynticks_completed to completed_fqs
  rcu: Enable synchronize_sched_expedited() fastpath
  rcu: Remove inline from forward-referenced functions
  rcu: Fix note_new_gpnum() uses of ->gpnum
  rcu: Fix synchronization for rcu_process_gp_end() uses of ->completed counter
  rcu: Prepare for synchronization fixes: clean up for non-NO_HZ handling of ->completed counter
  rcu: Cleanup: balance rcu_irq_enter()/rcu_irq_exit() calls
  ...

Merge branch 'core-printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  ratelimit: Make suppressed output messages more useful
  printk: Remove ratelimit.h from kernel.h
  ratelimit: Fix/allow use in atomic contexts
  ratelimit: Use per ratelimit context locking

Merge branch 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  mutex: Fix missing conditions to build mutex_spin_on_owner()
  mutex: Better control mutex adaptive spinning config
  locking, task_struct: Reduce size on TRACE_IRQFLAGS and 64bit
  locking: Use __[SPIN|RW]_LOCK_UNLOCKED in [spin|rw]_lock_init()
  locking: Remove unused prototype
  locking: Reduce ifdefs in kernel/spinlock.c
  locking: Make inlining decision Kconfig based

Merge branch 'core-ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  generic-ipi: Add smp_call_function_any()
  generic-ipi: Fix misleading smp_call_function*() description

Merge branch 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
  x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree
  x86/amd-iommu: Remove amd_iommu_pd_table
  x86/amd-iommu: Move reset_iommu_command_buffer out of locked code
  x86/amd-iommu: Cleanup DTE flushing code
  x86/amd-iommu: Introduce iommu_flush_device() function
  x86/amd-iommu: Cleanup attach/detach_device code
  x86/amd-iommu: Keep devices per domain in a list
  x86/amd-iommu: Add device bind reference counting
  x86/amd-iommu: Use dev->arch->iommu to store iommu related information
  x86/amd-iommu: Remove support for domain sharing
  x86/amd-iommu: Rearrange dma_ops related functions
  x86/amd-iommu: Move some pte allocation functions in the right section
  x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc
  x86/amd-iommu: Use get_device_id and check_device where appropriate
  x86/amd-iommu: Move find_protection_domain to helper functions
  x86/amd-iommu: Simplify get_device_resources()
  x86/amd-iommu: Let domain_for_device handle aliases
  x86/amd-iommu: Remove iommu specific handling from dma_ops path
  x86/amd-iommu: Remove iommu parameter from __(un)map_single
  x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw: (31 commits)
  GFS2: Fix glock refcount issues
  writeback: remove unused nonblocking and congestion checks (gfs2)
  GFS2: drop rindex glock to refresh rindex list
  GFS2: Tag all metadata with jid
  GFS2: Locking order fix in gfs2_check_blk_state
  GFS2: Remove dirent_first() function
  GFS2: Display nobarrier option in /proc/mounts
  GFS2: add barrier/nobarrier mount options
  GFS2: remove division from new statfs code
  GFS2: Improve statfs and quota usability
  GFS2: Use dquot_send_warning()
  VFS: Export dquot_send_warning
  GFS2: Add set_xquota support
  GFS2: Add get_xquota support
  GFS2: Clean up gfs2_adjust_quota() and do_glock()
  GFS2: Remove constant argument from qd_get()
  GFS2: Remove constant argument from qdsb_get()
  GFS2: Add proper error reporting to quota sync via sysfs
  GFS2: Add get_xstate quota function
  GFS2: Remove obsolete code in quota.c
  ...