- 31 Mar, 2013 21 commits
-
-
Sylwester Nawrocki authored
The s5p-fimc directory now contains drivers for multiple IP blocks found in multiple Samsung application processors. This includes FIMC (CAMIF), MIPI CSIS and FIMC LITE. FIMC-IS (Imaging Subsystem) driver is going to be put into same directory. Hence we rename it to exynos4-is as s5p-fimc was only relevant for early version of this driver, when it only supported FIMC IP block. The imaging subsystem drivers for Exynos4 SoC series and S5PV210 will be included in drivers/media/platform/exynos4-is directory, with some modules shared with exynos5 series, while the rest of exynos5 specific modules will find their home in drivers/media/platform/exynos5-is. Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sylwester Nawrocki authored
Drop fimc-lite.h header inclusion to make the exynos-fimc-lite module independent on other modules. Move struct fimc_fmt declaration to the driver's private headers as it is used in multiple modules. Reported-by:
Shaik Ameer Basha <shaik.ameer@samsung.com> Signed-off-by:
-
Sylwester Nawrocki authored
Since the FIMC-IS firmware communicates with an image sensor directly through the ISP I2C bus controllers the sub-devices power supplies cannot be simply enabled from left to right or disabled from right to left along the processing pipeline. Thus a subdev index to call s_power() on is looked up from a table, rather than doing the op call based on increasing/decreasing indexes. Signed-off-by:
-
Sylwester Nawrocki authored
Since the FIMC-IS firmware communicates with an image sensor directly through the ISP I2C bus controllers data streaming cannot be simply enabled from left to right or disabled from right to left along the processing pipeline. Thus a subdev index to call s_stream() on is looked up from a table, rather than doing the op call based on increasing/decreasing indexes. Signed-off-by:
-
Sylwester Nawrocki authored
In configurations where FIMC-LITE is used to capture image signal from an external sensor only we need to ensure one of FIMC devices is in active power state and the "fimc" gate clock is enabled. Otherwise the CAMCLK clock output signal will be masked off preventing an external sensor's operation. This affect processing pipelines like: - sensor -> FIMC-LITE -> memory - sensor -> MIPI-CSIS -> FIMC-LITE -> memory Signed-off-by:
-
Sylwester Nawrocki authored
A second sink pad is added to each FIMC.N subdev that will be used to link it to the FIMC-IS-ISP subdev. Only V4L2_MBUS_FMT_YUV10_1X30 format is supported at this pad (FIMC_SD_PAD_SINK_FIFO). The routine checking for mismatch in the image formats at sides of the links is updated to account for the fact FIMC.X subdevs now have sink pads at the pad indexes 0, 1 and source pad at pad index 2. If link to FIMC.X pad 1 is activated we switch FIMC input data bus type to the ISP Writeback. Only a single active link to FIMC.X pad 0 or 1 will be allowed at any time. Signed-off-by:
-
Sylwester Nawrocki authored
This patch ads handling of clocks for the CAMBLK subsystem which is a glue logic for FIMC-IS or LCD controller and FIMC IP. Signed-off-by:
-
Sylwester Nawrocki authored
We cannot assume that the passed entity the fimc_pipeline_prepare() function is supposed to start the media graph traversal from will always have its sink pad at pad index 0. Find the starting media entity's sink pad by iterating over its all pads and checking the pad flags. This ensures proper handling of FIMC, FIMC-LITE and FIMC-IS-ISP subdevs that have more than one sink and one source pad. Signed-off-by:
-
Andrzej Hajda authored
set_stream error for pipelines is logged or reported to user space if possible. Signed-off-by:
Andrzej Hajda <a.hajda@samsung.com> Signed-off-by:
-
Sylwester Nawrocki authored
This patch adds a menu option to the V4L2_CID_EXPOSURE_METERING control for multi-zone metering. Signed-off-by:
-
Sylwester Nawrocki authored
Before the camera ports can be used the pinmux needs to be configured properly. This patch adds a function to set the camera ports pinctrl to a default state within the media driver's probe(). The camera port(s) are then configured for the video bus operation. Signed-off-by:
-
Sylwester Nawrocki authored
The sensor (I2C and/or SPI client) devices are instantiated by their corresponding control bus drivers. Since the I2C client's master clock is often provided by a video bus receiver (host interface) or other than I2C/SPI controller device, the drivers of those client devices are not accessing hardware in their driver's probe() callback. Instead, after enabling clock, the host driver calls back into a sub-device when it wants to activate them. This pattern is used by some in-tree drivers and this patch also uses it for DT case. This patch is intended as a first step for adding device tree support to the S5P/Exynos SoC camera drivers. The second one is adding support for asynchronous sub-devices registration and clock control from sub-device driver level. The bindings shall not change when asynchronous probing support is added. Signed-off-by:
-
Sylwester Nawrocki authored
This patch adds changes required for the main camera media device driver corresponding to the top level 'camera' device node. The drivers of devices corresponding to child nodes of the 'camera' node are looked up and and registered as sub-devices to the top level driver. The main driver's probing is deferred if any of the sub-device drivers is not yet initialized and ready. Signed-off-by:
-
Sylwester Nawrocki authored
This patch adds the device tree support for FIMC-LITE device driver. The bindings include compatible property for the Exynos5 SoC series, however the actual implementation for these SoCs will be added in a separate patch. Signed-off-by:
-
Sylwester Nawrocki authored
This patch adds device tree support for FIMC driver on S5PV210 and Exynos4 SoCs. The FIMC IP block's features and quirks encoded statically in the driver are now parsed from the device tree. Once all relevant platforms are converted to device tree based booting the FIMC variant data structures will all be removed from the driver. Signed-off-by:
-
Sylwester Nawrocki authored
This patch support for binding the driver to the MIPI-CSIS devices instantiated from device tree and parsing the SoC and board specific properties. The MIPI CSI-2 channel is determined by the value of reg property placed in csis' port subnode. Signed-off-by:
-
Sylwester Nawrocki authored
Replace some ioctl, file and video buffer queue operation handlers with the videobuf2 helpers. This allows to get rid of significant amount of boilerplate. Signed-off-by:
-
Sylwester Nawrocki authored
mmap/poll file operation and several ioctl handlers are replaced with the vb2 helper functions. Some helpers are used indirectly to maintain the buffer queue ownership. Signed-off-by:
-
Sylwester Nawrocki authored
It doesn't matter whether we start from the sensor of from the video node entity. Remove use of pipeline->subdevs array where possible, so we can partly drop dependency on struct fimc_pipeline in the fimc-lite module, which is also used by the exynos5-is driver. Also make sure we revert any media entity pipeline operations when vb2_streamon() function fails. Signed-off-by:
-
Guennadi Liakhovetski authored
Add a V4L2 OF parser, implementing bindings documented in Documentation/devicetree/bindings/media/video-interfaces.txt. [s.nawrocki@samsung.com: various corrections and improvements since the initial version] Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Guennadi Liakhovetski authored
This patch adds a document describing common OF bindings for video capture, output and video processing devices. It is curently mainly focused on video capture devices, with data busses defined by standards such as ITU-R BT.656 or MIPI-CSI2. It also documents a method of describing data links between devices. Signed-off-by:
-
- 29 Mar, 2013 19 commits
-
-
Hans Verkuil authored
These ranges shouldn't overlap. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Hans Verkuil authored
Loading the cypress firmware is not dvb specific and should be common functionality. Move the source to media/common and make it a standalone module. As a result we can remove the dependency on dvb-usb in go7007, which has nothing to do with dvb. Signed-off-by:
-
Mauro Carvalho Chehab authored
vidioc_s_tuner, vidioc_s_frequency and vidioc_s_register now uses a constant argument. So, the driver reports warnings: drivers/media/radio/radio-si476x.c:1196:2: warning: initialization from incompatible pointer type [enabled by default] drivers/media/radio/radio-si476x.c:1196:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_tuner') [enabled by default] drivers/media/radio/radio-si476x.c:1199:2: warning: initialization from incompatible pointer type [enabled by default] drivers/media/radio/radio-si476x.c:1199:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_frequency') [enabled by default] drivers/media/radio/radio-si476x.c:1209:2: warning: initialization from incompatible pointer type [enabled by default] drivers/media/radio/radio-si476x.c:1209:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_register') [enabled by default] This is due to a (soft) merge conflict, as both this driver and the const patches were applied for the same Kernel version. Cc: Hans Verkuil <hans.verkuil@cisco.com> Cc: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: -
Andrey Smirnov authored
This commit adds a driver that exposes all the radio related functionality of the Si476x series of chips via the V4L2 subsystem. Acked-by:
Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by:
-
Andrey Smirnov authored
Add a base to be used for allocation of all the SI476X specific controls in the corresponding driver. Acked-by:
-
Andrey Smirnov authored
Add appropriate documentation for all the newly added standard controls. Based on the patch by Manjunatha Halli [1] [1] http://lists-archives.com/linux-kernel/27641303-media-update-docs-for-v4l2-fm-new-features.htmlAcked-by:
-
Andrey Smirnov authored
This commit introduces new class of standard controls V4L2_CTRL_CLASS_FM_RX. This class is intended to all controls pertaining to FM receiver chips. Also, two controls belonging to said class are added as a part of this commit: V4L2_CID_TUNE_DEEMPHASIS and V4L2_CID_RDS_RECEPTION. This patch is based on the code found in the patch by Manjunatha Halli [1] [1] http://lists-archives.com/linux-kernel/27641307-new-control-class-and-features-for-fm-rx.htmlAcked-by:
-
Andrey Smirnov authored
Change the type of V4L2_CID_TUNE_PREEMPHASIS from 'integer' to 'enum v4l2_preemphasis' Acked-by:
-
Andrey Smirnov authored
This patch adds all necessary header files and Kbuild plumbing for the core driver for Silicon Laboratories Si476x series of AM/FM tuner chips. The driver as a whole is implemented as an MFD device and this patch adds a core portion of it that provides all the necessary functionality to the two other drivers that represent radio and audio codec subsystems of the chip. Acked-by:
Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
-
Andrey Smirnov authored
This patch adds code related to manipulation of the properties of SI476X chips. Acked-by:
-
Andrey Smirnov authored
This patch adds main part(out of three) of the I2C driver for the "core" of MFD device. Acked-by:
-
Andrey Smirnov authored
This patch adds all the functions used for exchanging commands with the chip. Acked-by:
-
Hans Verkuil authored
On powerpc the maximum size for the ioctl argument is 8191, and it was 8192. However, the 64x64 array of threshold values is more than is actually needed in practice for PAL and NTSC formats. A 45x45 array will do just fine. So change the size accordingly to fix this problem. Signed-off-by:
-
Alexey Klimov authored
If i run verbose v4l2-compliance with my radio-mr800 device few times then i get warning about frequency out of range: root@machine:~# v4l2-compliance -r /dev/radio0 -v 2 is radio Driver Info: Driver name : radio-mr800 Card type : AverMedia MR 800 USB FM Radio Bus info : usb-0000:00:1a.0-1.2 Driver version: 3.9.0 Capabilities : 0x80050400 Tuner Radio Device Capabilities Device Caps : 0x00050400 Tuner Radio Compliance test for device /dev/radio0 (not using libv4l2): Required ioctls: test VIDIOC_QUERYCAP: OK Allow for multiple opens: test second radio open: OK test VIDIOC_QUERYCAP: OK test VIDIOC_G/S_PRIORITY: OK Debug ioctls: test VIDIOC_DBG_G_CHIP_IDENT: OK (Not Supported) test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported) test VIDIOC_LOG_STATUS: OK Input ioctls: test VIDIOC_G/S_TUNER: OK warn: v4l2-test-input-output.cpp(234): returned tuner 0 frequency out of range (6550200 not in [1400000...1728000]) test VIDIOC_G/S_FREQUENCY: OK test VIDIOC_S_HW_FREQ_SEEK: OK test VIDIOC_ENUMAUDIO: OK (Not Supported) test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) test VIDIOC_G/S_AUDIO: OK (Not Supported) Inputs: 0 Audio Inputs: 0 Tuners: 1 Output ioctls: test VIDIOC_G/S_MODULATOR: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK test VIDIOC_ENUMAUDOUT: OK (Not Supported) test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) test VIDIOC_G/S_AUDOUT: OK (Not Supported) Outputs: 0 Audio Outputs: 0 Modulators: 0 Control ioctls: info: checking v4l2_queryctrl of control 'User Controls' (0x00980001) info: checking v4l2_queryctrl of control 'Mute' (0x00980909) info: checking v4l2_queryctrl of control 'Mute' (0x00980909) test VIDIOC_QUERYCTRL/MENU: OK info: checking control 'User Controls' (0x00980001) info: checking control 'Mute' (0x00980909) test VIDIOC_G/S_CTRL: OK info: checking extended control 'User Controls' (0x00980001) info: checking extended control 'Mute' (0x00980909) test VIDIOC_G/S/TRY_EXT_CTRLS: OK info: checking control event 'User Controls' (0x00980001) info: checking control event 'Mute' (0x00980909) test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 2 Private Controls: 0 Input/Output configuration ioctls: test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_PRESETS: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) Format ioctls: test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported) test VIDIOC_G/S_PARM: OK (Not Supported) test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK (Not Supported) test VIDIOC_TRY_FMT: OK (Not Supported) test VIDIOC_S_FMT: OK (Not Supported) test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) Codec ioctls: test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) Buffer ioctls: test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported) Total: 38, Succeeded: 38, Failed: 0, Warnings: 1 Some printk() debugging showed that vidioc_s_hw_freq_seek() setups radio->curfreq to out of range value (lines 395-396) and calls amradio_set_freq() to set this frequency on device without any out-of-range checks. Patch protects from setting up frequency on device to incorrect value moving clamp_t check inside amradio_set_freq. With this patch we can call amradio_set_freq() with out of range frequency from any place. Also put comment that sometimes radio->curfreq is set to out of range value in vidioc_s_hw_freq_seek(). Signed-off-by:
Alexey Klimov <klimov.linux@gmail.com> Acked-by:
-
Paul Bolle authored
The et61x251 driver was removed in v3.5. Remove the last references to its Kconfig macro now. Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
Mauro Carvalho Chehab authored
ioctl's number is unsigned int. Fix it at vidioc_default. Signed-off-by: -
Masanari Iida authored
Correct spelling typo in staging/media/davinci Signed-off-by:
Masanari Iida <standby24x7@gmail.com> Signed-off-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
Frank Schaefer authored
This sensor is used by the "SpeedLink Vicious And Devine Laplace webcam" and others. It supports resolutions up to 1600x1200 (at 7-8 fps), but for resolutions higher than 640x480, further driver changes will be necessary, such as sensor output resolution switching (including further configuration changes), bridge xclk adjustment and disabling of 16 bit (12 bit) output formats at high resolutions. Image quality should also needs to be improved. Signed-off-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Frank Schaefer authored
The Windows driver also probes at least two further i2c addresses (0x22 >> 1 and 0x66 >> 1). I've got some hints that they are very likely used by Samsung and Kodak sensors, which are known to be used in Empia devices, too. We havn't seen any devices using these sensors yet and don't know how to probe them properly, so leave a comment. Signed-off-by:
-
