- 20 Oct, 2016 5 commits
-
-
Paul Blakey authored
stats_update callback is called by NIC drivers doing hardware offloading of the mirred action. Lastuse is passed as argument to specify when the stats was actually last updated and is not always the current time. Fixes: 9798e6fe ('net: act_mirred: allow statistic updates from offloaded actions') Signed-off-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
SwitchX2 firmware does not implement reset done yet. Moreover, when busy-polled for ready magic, that slows down firmware and reset takes longer than the defined timeout, causing initialization to fail. So restore the previous behaviour and just sleep in this case. Fixes: 233fa44b ("mlxsw: pci: Implement reset done check") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Elad Raz authored
When creating an ethernet port fails, we must move the port to disable, otherwise putting the port in switch partition 0 (ETH) or 1 (IB) will always fails. Fixes: 31557f0f ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support") Signed-off-by: Elad Raz <eladr@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
The function return value is not checked anywhere. Also, the warning causes huge slowdown when removing large number of FIB entries which were not offloaded, because of ordering issue. Ido's preparing a patchset to fix the ordering issue, but that is definitelly not net tree material. Fixes: b45f64d1 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
By a mistake, there is tree index 0 passed to RALTB. Should be MLXSW_SP_LPM_TREE_MIN. Fixes: b45f64d1 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls") Reported-by: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 19 Oct, 2016 6 commits
-
-
Giuseppe CAVALLARO authored
The commit commit 7086605a ("stmmac: fix error check when init ptp") breaks the procedure added by the commit efee95f4 ("ptp_clock: future-proofing drivers against PTP subsystem becoming optional") So this patch tries to re-import the logic added by the latest commit above: it makes sense to have the stmmac_ptp_register as void function and, inside the main, the stmmac_init_ptp can fails in case of the capability cannot be supported by the HW. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre TORGUE <alexandre.torgue@st.com> Cc: Rayagond Kokatanur <rayagond@vayavyalabs.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Nicolas Pitre <nico@linaro.org> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Since commit b2fb4f54 ("tcp: uninline tcp_prequeue()") we no longer access sysctl_tcp_low_latency from a module. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
The offload flag is a status flag and should not be used by FIB semantics for comparison. Fixes: 37ed9493 ("rtnetlink: add RTNH_F_EXTERNAL flag for fib offload") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
We recently got the following warning after setting up a vlan device on top of an offloaded bridge and executing 'bridge link': WARNING: CPU: 0 PID: 18566 at drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c:81 mlxsw_sp_port_orig_get.part.9+0x55/0x70 [mlxsw_spectrum] [...] CPU: 0 PID: 18566 Comm: bridge Not tainted 4.8.0-rc7 #1 Hardware name: Mellanox Technologies Ltd. Mellanox switch/Mellanox switch, BIOS 4.6.5 05/21/2015 0000000000000286 00000000e64ab94f ffff880406e6f8f0 ffffffff8135eaa3 0000000000000000 0000000000000000 ffff880406e6f930 ffffffff8108c43b 0000005106e6f988 ffff8803df398840 ffff880403c60108 ffff880406e6f990 Call Trace: [<ffffffff8135eaa3>] dump_stack+0x63/0x90 [<ffffffff8108c43b>] __warn+0xcb/0xf0 [<ffffffff8108c56d>] warn_slowpath_null+0x1d/0x20 [<ffffffffa01420d5>] mlxsw_sp_port_orig_get.part.9+0x55/0x70 [mlxsw_spectrum] [<ffffffffa0142195>] mlxsw_sp_port_attr_get+0xa5/0xb0 [mlxsw_spectrum] [<ffffffff816f151f>] switchdev_port_attr_get+0x4f/0x140 [<ffffffff816f15d0>] switchdev_port_attr_get+0x100/0x140 [<ffffffff816f15d0>] switchdev_port_attr_get+0x100/0x140 [<ffffffff816f1d6b>] switchdev_port_bridge_getlink+0x5b/0xc0 [<ffffffff816f2680>] ? switchdev_port_fdb_dump+0x90/0x90 [<ffffffff815f5427>] rtnl_bridge_getlink+0xe7/0x190 [<ffffffff8161a1b2>] netlink_dump+0x122/0x290 [<ffffffff8161b0df>] __netlink_dump_start+0x15f/0x190 [<ffffffff815f5340>] ? rtnl_bridge_dellink+0x230/0x230 [<ffffffff815fab46>] rtnetlink_rcv_msg+0x1a6/0x220 [<ffffffff81208118>] ? __kmalloc_node_track_caller+0x208/0x2c0 [<ffffffff815f5340>] ? rtnl_bridge_dellink+0x230/0x230 [<ffffffff815fa9a0>] ? rtnl_newlink+0x890/0x890 [<ffffffff8161cf54>] netlink_rcv_skb+0xa4/0xc0 [<ffffffff815f56f8>] rtnetlink_rcv+0x28/0x30 [<ffffffff8161c92c>] netlink_unicast+0x18c/0x240 [<ffffffff8161ccdb>] netlink_sendmsg+0x2fb/0x3a0 [<ffffffff815c5a48>] sock_sendmsg+0x38/0x50 [<ffffffff815c6031>] SYSC_sendto+0x101/0x190 [<ffffffff815c7111>] ? __sys_recvmsg+0x51/0x90 [<ffffffff815c6b6e>] SyS_sendto+0xe/0x10 [<ffffffff817017f2>] entry_SYSCALL_64_fastpath+0x1a/0xa4 The problem is that the 8021q module propagates the call to ndo_bridge_getlink() via switchdev ops, but the switch driver doesn't recognize the netdev, as it's not offloaded. While we can ignore calls being made to non-bridge ports inside the driver, a better fix would be to push this check up to the switchdev layer. Note that these ndos can be called for non-bridged netdev, but this only happens in certain PF drivers which don't call the corresponding switchdev functions anyway. Fixes: 99f44bb3 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Tamir Winetroub <tamirw@mellanox.com> Tested-by: Tamir Winetroub <tamirw@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Tamir reported the following trace when processing ARP requests received via a vlan device on top of a VLAN-aware bridge: NMI watchdog: BUG: soft lockup - CPU#1 stuck for 22s! [swapper/1:0] [...] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G W 4.8.0-rc7 #1 Hardware name: Mellanox Technologies Ltd. "MSN2100-CB2F"/"SA001017", BIOS 5.6.5 06/07/2016 task: ffff88017edfea40 task.stack: ffff88017ee10000 RIP: 0010:[<ffffffff815dcc73>] [<ffffffff815dcc73>] netdev_all_lower_get_next_rcu+0x33/0x60 [...] Call Trace: <IRQ> [<ffffffffa015de0a>] mlxsw_sp_port_lower_dev_hold+0x5a/0xa0 [mlxsw_spectrum] [<ffffffffa016f1b0>] mlxsw_sp_router_netevent_event+0x80/0x150 [mlxsw_spectrum] [<ffffffff810ad07a>] notifier_call_chain+0x4a/0x70 [<ffffffff810ad13a>] atomic_notifier_call_chain+0x1a/0x20 [<ffffffff815ee77b>] call_netevent_notifiers+0x1b/0x20 [<ffffffff815f2eb6>] neigh_update+0x306/0x740 [<ffffffff815f38ce>] neigh_event_ns+0x4e/0xb0 [<ffffffff8165ea3f>] arp_process+0x66f/0x700 [<ffffffff8170214c>] ? common_interrupt+0x8c/0x8c [<ffffffff8165ec29>] arp_rcv+0x139/0x1d0 [<ffffffff816e505a>] ? vlan_do_receive+0xda/0x320 [<ffffffff815e3794>] __netif_receive_skb_core+0x524/0xab0 [<ffffffff815e6830>] ? dev_queue_xmit+0x10/0x20 [<ffffffffa06d612d>] ? br_forward_finish+0x3d/0xc0 [bridge] [<ffffffffa06e5796>] ? br_handle_vlan+0xf6/0x1b0 [bridge] [<ffffffff815e3d38>] __netif_receive_skb+0x18/0x60 [<ffffffff815e3dc0>] netif_receive_skb_internal+0x40/0xb0 [<ffffffff815e3e4c>] netif_receive_skb+0x1c/0x70 [<ffffffffa06d7856>] br_pass_frame_up+0xc6/0x160 [bridge] [<ffffffffa06d63d7>] ? deliver_clone+0x37/0x50 [bridge] [<ffffffffa06d656c>] ? br_flood+0xcc/0x160 [bridge] [<ffffffffa06d7b14>] br_handle_frame_finish+0x224/0x4f0 [bridge] [<ffffffffa06d7f94>] br_handle_frame+0x174/0x300 [bridge] [<ffffffff815e3599>] __netif_receive_skb_core+0x329/0xab0 [<ffffffff81374815>] ? find_next_bit+0x15/0x20 [<ffffffff8135e802>] ? cpumask_next_and+0x32/0x50 [<ffffffff810c9968>] ? load_balance+0x178/0x9b0 [<ffffffff815e3d38>] __netif_receive_skb+0x18/0x60 [<ffffffff815e3dc0>] netif_receive_skb_internal+0x40/0xb0 [<ffffffff815e3e4c>] netif_receive_skb+0x1c/0x70 [<ffffffffa01544a1>] mlxsw_sp_rx_listener_func+0x61/0xb0 [mlxsw_spectrum] [<ffffffffa005c9f7>] mlxsw_core_skb_receive+0x187/0x200 [mlxsw_core] [<ffffffffa007332a>] mlxsw_pci_cq_tasklet+0x63a/0x9b0 [mlxsw_pci] [<ffffffff81091986>] tasklet_action+0xf6/0x110 [<ffffffff81704556>] __do_softirq+0xf6/0x280 [<ffffffff8109213f>] irq_exit+0xdf/0xf0 [<ffffffff817042b4>] do_IRQ+0x54/0xd0 [<ffffffff8170214c>] common_interrupt+0x8c/0x8c The problem is that netdev_all_lower_get_next_rcu() never advances the iterator, thereby causing the loop over the lower adjacency list to run forever. Fix this by advancing the iterator and avoid the infinite loop. Fixes: 7ce856aa ("mlxsw: spectrum: Add couple of lower device helper functions") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Tamir Winetroub <tamirw@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Garver authored
Fixes a panic when calling eth_get_headlen(). Noticed on i40e driver. Fixes: d5709f7a ("flow_dissector: For stripped vlan, get vlan info from skb->vlan_tci") Signed-off-by: Eric Garver <e@erig.me> Reviewed-by: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Amir Vadai <amir@vadai.me> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 18 Oct, 2016 17 commits
-
-
Wei Yongjun authored
Using list_move_tail() instead of list_del() + list_add_tail(). Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Arnd Bergmann authored
In some rare configurations, we get a warning about the 'index' variable being used without an initialization: drivers/net/ethernet/rocker/rocker_ofdpa.c: In function ‘ofdpa_port_fib_ipv4.isra.16.constprop’: drivers/net/ethernet/rocker/rocker_ofdpa.c:2425:92: warning: ‘index’ may be used uninitialized in this function [-Wmaybe-uninitialized] This is a false positive, the logic is just a bit too complex for gcc to follow here. Moving the intialization of 'index' a little further down makes it clear to gcc that the function always returns an error if it is not initialized. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Arnd Bergmann authored
The hdr_offset variable is only if we deal with a TCP or UDP packet, but as the check surrounding its usage tests for skb_is_gso() instead, the compiler has no idea if the variable is initialized or not at that point: drivers/net/hyperv/netvsc_drv.c: In function ‘netvsc_start_xmit’: drivers/net/hyperv/netvsc_drv.c:494:42: error: ‘hdr_offset’ may be used uninitialized in this function [-Werror=maybe-uninitialized] This adds an additional check for the transport type, which tells the compiler that this path cannot happen. Since the get_net_transport_info() function should always be inlined here, I don't expect this to result in additional runtime checks. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Arnd Bergmann authored
gcc found a reference to an uninitialized variable in the error handling of bcm_enet_open, introduced by a recent cleanup: drivers/net/ethernet/broadcom/bcm63xx_enet.c: In function 'bcm_enet_open' drivers/net/ethernet/broadcom/bcm63xx_enet.c:1129:2: warning: 'phydev' may be used uninitialized in this function [-Wmaybe-uninitialized] This makes the use of that variable conditional, so we only reference it here after it has been used before. Unlike my normal patches, I have not build-tested this one, as I don't currently have mips test in my randconfig setup. Fixes: 625eb866 ("net: ethernet: broadcom: bcm63xx: use phydev from struct net_device") Cc: Philippe Reynes <tremyfr@gmail.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
reuseport_add_sock() is not used from a module, no need to export it. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Thomas Falcon authored
It is possible for the MTU to be changed during the initialization process with the VNIC Server. Ensure that the net device is updated to reflect the new MTU. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Thomas Falcon authored
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Thomas Falcon authored
Increment driver version to reflect features that have been added since release. Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nikolay Aleksandrov authored
Satish reported a problem with the perm multicast router ports not getting reenabled after some series of events, in particular if it happens that the multicast snooping has been disabled and the port goes to disabled state then it will be deleted from the router port list, but if it moves into non-disabled state it will not be re-added because the mcast snooping is still disabled, and enabling snooping later does nothing. Here are the steps to reproduce, setup br0 with snooping enabled and eth1 added as a perm router (multicast_router = 2): 1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping 2. $ ip l set eth1 down ^ This step deletes the interface from the router list 3. $ ip l set eth1 up ^ This step does not add it again because mcast snooping is disabled 4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping 5. $ bridge -d -s mdb show <empty> At this point we have mcast enabled and eth1 as a perm router (value = 2) but it is not in the router list which is incorrect. After this change: 1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping 2. $ ip l set eth1 down ^ This step deletes the interface from the router list 3. $ ip l set eth1 up ^ This step does not add it again because mcast snooping is disabled 4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping 5. $ bridge -d -s mdb show router ports on br0: eth1 Note: we can directly do br_multicast_enable_port for all because the querier timer already has checks for the port state and will simply expire if it's in blocking/disabled. See the comment added by commit 9aa66382 ("bridge: multicast: add a comment to br_port_state_selection about blocking state") Fixes: 561f1103 ("bridge: Add multicast_snooping sysfs toggle") Reported-by: Satish Ashok <sashok@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Tobias Klauser authored
Remove the unused but set variable icsk in listening_get_next to fix the following GCC warning when building with 'W=1': net/ipv4/tcp_ipv4.c: In function ‘listening_get_next’: net/ipv4/tcp_ipv4.c:1890:31: warning: variable ‘icsk’ set but not used [-Wunused-but-set-variable] Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ganesh Goudar authored
Do not let number of offload queue sets to go more than MAX_OFLD_QSETS, which would otherwise crash the driver on machines with cores more than MAX_OFLD_QSETS. Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Tobias Klauser authored
Remove the unused but set variable dev in ip_do_fragment to fix the following GCC warning when building with 'W=1': net/ipv4/ip_output.c: In function ‘ip_do_fragment’: net/ipv4/ip_output.c:541:21: warning: variable ‘dev’ set but not used [-Wunused-but-set-variable] Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Niklas Cassel authored
Allow autoneg to enable flow control by default. The behavior when autoneg is off has not changed. Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: Jesper Nilsson <jespern@axis.com> Acked-by: Lars Persson <larper@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Niklas Cassel authored
phy_device->supported is originally set by the PHY driver. The ethernet driver should filter phy_device->supported to only contain flags supported by the IP. The IP supports setting rx and tx flow control independently, therefore SUPPORTED_Pause and SUPPORTED_Asym_Pause should not be cleared. If the flags are cleared, pause frames cannot be enabled (even if they are supported by the PHY). Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: Jesper Nilsson <jespern@axis.com> Acked-by: Lars Persson <larper@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Tobias Klauser authored
Remove the unused but set variable master_dev in check_local_dest to fix the following GCC warning when building with 'W=1': net/hsr/hsr_forward.c: In function ‘check_local_dest’: net/hsr/hsr_forward.c:303:21: warning: variable ‘master_dev’ set but not used [-Wunused-but-set-variable] Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'mac80211-for-davem-2016-10-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== This is relatively small, mostly to get the SG/crypto from stack removal fix that crashes things when VMAP stack is used in conjunction with software crypto. Aside from that, we have: * a fix for AP_VLAN usage with the nl80211 frame command * two fixes (and two preparation patches) for A-MSDU, one to discard group-addressed (multicast) and unexpected 4-address A-MSDUs, the other to validate A-MSDU inner MAC addresses properly to prevent controlled port bypass ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ivan Vecera authored
Functions bnx2_reg_rd_ind(), bnx2_reg_wr_ind() and bnx2_ctx_wr() can be called with IRQs disabled when netconsole is enabled. So they should use spin_{,un}lock_irq{save,restore} instead of _bh variants. Example call flow: bnx2_poll() ->bnx2_poll_link() ->bnx2_phy_int() ->bnx2_set_remote_link() ->bnx2_shmem_rd() ->bnx2_reg_rd_ind() -> spin_lock_bh(&bp->indirect_lock); spin_unlock_bh(&bp->indirect_lock); ... -> __local_bh_enable_ip static inline void __local_bh_enable_ip(unsigned long ip) WARN_ON_ONCE(in_irq() || irqs_disabled()); <<<<<< WARN Cc: Sony Chacko <sony.chacko@qlogic.com> Cc: Dept-HSGLinuxNICDev@qlogic.com Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 17 Oct, 2016 12 commits
-
-
David S. Miller authored
Javier Martinez Canillas says: ==================== net: Fix module autoload for several platform drivers I noticed that module autoload won't be working in a bunch of platform drivers in the net subsystem and this patch series contains the fixes. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Javier Martinez Canillas authored
If the driver is built as a module, autoload won't work because the module alias information is not filled. So user-space can't match the registered device with the corresponding module. Export the module alias information using the MODULE_DEVICE_TABLE() macro. Before this patch: $ modinfo drivers/net/dsa/bcm_sf2.ko | grep alias alias: platform:brcm-sf2 After this patch: $ modinfo drivers/net/dsa/bcm_sf2.ko | grep alias alias: platform:brcm-sf2 alias: of:N*T*Cbrcm,bcm7445-switch-v4.0C* alias: of:N*T*Cbrcm,bcm7445-switch-v4.0 Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Javier Martinez Canillas authored
If the driver is built as a module, autoload won't work because the module alias information is not filled. So user-space can't match the registered device with the corresponding module. Export the module alias information using the MODULE_DEVICE_TABLE() macro. Before this patch: $ modinfo drivers/net/dsa/b53/b53_mmap.ko | grep alias $ After this patch: $ modinfo drivers/net/dsa/b53/b53_mmap.ko | grep alias alias: of:N*T*Cbrcm,bcm63xx-switchC* alias: of:N*T*Cbrcm,bcm63xx-switch alias: of:N*T*Cbrcm,bcm6368-switchC* alias: of:N*T*Cbrcm,bcm6368-switch alias: of:N*T*Cbrcm,bcm6328-switchC* alias: of:N*T*Cbrcm,bcm6328-switch alias: of:N*T*Cbrcm,bcm3384-switchC* alias: of:N*T*Cbrcm,bcm3384-switch Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Javier Martinez Canillas authored
If the driver is built as a module, autoload won't work because the module alias information is not filled. So user-space can't match the registered device with the corresponding module. Export the module alias information using the MODULE_DEVICE_TABLE() macro. Before this patch: $ modinfo drivers/net/ethernet/hisilicon//hns_mdio.ko | grep alias alias: platform:Hi-HNS_MDIO alias: acpi*:HISI0141:* After this patch: $ modinfo drivers/net/ethernet/hisilicon//hns_mdio.ko | grep alias alias: platform:Hi-HNS_MDIO alias: of:N*T*Chisilicon,hns-mdioC* alias: of:N*T*Chisilicon,hns-mdio alias: of:N*T*Chisilicon,mdioC* alias: of:N*T*Chisilicon,mdio alias: acpi*:HISI0141:* Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Javier Martinez Canillas authored
If the driver is built as a module, autoload won't work because the module alias information is not filled. So user-space can't match the registered device with the corresponding module. Export the module alias information using the MODULE_DEVICE_TABLE() macro. Before this patch: $ modinfo drivers/net/ethernet/qualcomm/emac/qcom-emac.ko | grep alias alias: platform:qcom-emac After this patch: $ modinfo drivers/net/ethernet/qualcomm/emac/qcom-emac.ko | grep alias alias: platform:qcom-emac alias: of:N*T*Cqcom,fsm9900-emacC* alias: of:N*T*Cqcom,fsm9900-emac Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Acked-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Javier Martinez Canillas authored
If the driver is built as a module, autoload won't work because the module alias information is not filled. So user-space can't match the registered device with the corresponding module. Export the module alias information using the MODULE_DEVICE_TABLE() macro. Before this patch: $ modinfo drivers/net/ethernet/hisilicon/hns/hns_dsaf.ko | grep alias alias: acpi*:HISI00B2:* alias: acpi*:HISI00B1:* After this patch: $ modinfo drivers/net/ethernet/hisilicon/hns/hns_dsaf.ko | grep alias alias: acpi*:HISI00B2:* alias: acpi*:HISI00B1:* alias: of:N*T*Chisilicon,hns-dsaf-v2C* alias: of:N*T*Chisilicon,hns-dsaf-v2 alias: of:N*T*Chisilicon,hns-dsaf-v1C* alias: of:N*T*Chisilicon,hns-dsaf-v1 Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Javier Martinez Canillas authored
If the driver is built as a module, autoload won't work because the module alias information is not filled. So user-space can't match the registered device with the corresponding module. Export the module alias information using the MODULE_DEVICE_TABLE() macro. Before this patch: $ $ modinfo drivers/net/ethernet/aurora/nb8800.ko | grep alias $ After this patch: $ modinfo drivers/net/ethernet/aurora/nb8800.ko | grep alias alias: of:N*T*Csigma,smp8734-ethernetC* alias: of:N*T*Csigma,smp8734-ethernet alias: of:N*T*Csigma,smp8642-ethernetC* alias: of:N*T*Csigma,smp8642-ethernet alias: of:N*T*Caurora,nb8800C* alias: of:N*T*Caurora,nb8800 Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Acked-by: Mans Rullgard <mans@mansr.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Javier Martinez Canillas authored
If the driver is built as a module, autoload won't work because the module alias information is not filled. So user-space can't match the registered device with the corresponding module. Export the module alias information using the MODULE_DEVICE_TABLE() macro. Before this patch: $ modinfo drivers/net/ethernet/ezchip/nps_enet.ko | grep alias $ After this patch: $ modinfo drivers/net/ethernet/ezchip/nps_enet.ko | grep alias alias: of:N*T*Cezchip,nps-mgt-enetC* alias: of:N*T*Cezchip,nps-mgt-enet Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Colin Ian King authored
A memory leak of qe occurs when t4_sched_queue_unbind fails, so fix this by free'ing qe on the error exit path. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
After Jesper commit back in linux-3.18, we trigger a lockdep splat in proc_create_data() while allocating memory from pktgen_change_name(). This patch converts t->if_lock to a mutex, since it is now only used from control path, and adds proper locking to pktgen_change_name() 1) pktgen_thread_lock to protect the outer loop (iterating threads) 2) t->if_lock to protect the inner loop (iterating devices) Note that before Jesper patch, pktgen_change_name() was lacking proper protection, but lockdep was not able to detect the problem. Fixes: 8788370a ("pktgen: RCU-ify "if_list" to remove lock in next_to_run()") Reported-by: John Sperbeck <jsperbeck@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David Ahern authored
Currently, socket lookups for l3mdev (vrf) use cases can match a socket that is bound to a port but not a device (ie., a global socket). If the sysctl tcp_l3mdev_accept is not set this leads to ack packets going out based on the main table even though the packet came in from an L3 domain. The end result is that the connection does not establish creating confusion for users since the service is running and a socket shows in ss output. Fix by requiring an exact dif to sk_bound_dev_if match if the skb came through an interface enslaved to an l3mdev device and the tcp_l3mdev_accept is not set. skb's through an l3mdev interface are marked by setting a flag in inet{6}_skb_parm. The IPv6 variant is already set; this patch adds the flag for IPv4. Using an skb flag avoids a device lookup on the dif. The flag is set in the VRF driver using the IP{6}CB macros. For IPv4, the inet_skb_parm struct is moved in the cb per commit 971f10ec, so the match function in the TCP stack needs to use TCP_SKB_CB. For IPv6, the move is done after the socket lookup, so IP6CB is used. The flags field in inet_skb_parm struct needs to be increased to add another flag. There is currently a 1-byte hole following the flags, so it can be expanded to u16 without increasing the size of the struct. Fixes: 193125db ("net: Introduce VRF device driver") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ard Biesheuvel authored
Some crypto implementations (such as the generic CCM wrapper in crypto/) use scatterlists to map fields of private data in their struct aead_req. This means these data structures cannot live in the vmalloc area, which means that they cannot live on the stack (with CONFIG_VMAP_STACK.) This currently occurs only with the generic software implementation, but the private data and usage is implementation specific, so move the whole data structures off the stack into heap by allocating every time we need to use them. In addition, take care not to put any of our own stack allocations into scatterlists. This involves reserving some extra room when allocating the aead_request structures, and referring to those allocations in the scatter- lists (while copying the data from the stack before the crypto operation) Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-