When we have CONFIG_STRICT_KERNEL_RWX enabled, we want to split the
linear mapping at the text/data boundary so we can map the kernel
text read only.

The current logic uses a goto inside the for loop, which works, but is
hard to reason about.

When we hit the goto retry case we set max_mapping_size to PMD_SIZE
and go back to the start.

Setting max_mapping_size means we skip the PUD case and go to the PMD
case.

We know we will pass the alignment and gap checks because the only
reason we are there is we hit the goto retry, and that is guarded by
mapping_size == PUD_SIZE, which means addr is PUD aligned and gap is
greater or equal to PUD_SIZE.

So the only part of the check that can fail is the mmu_psize_defs
check for the 2M page size.

If we just duplicate that check we can avoid the goto, and we get the
same result.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When we have CONFIG_STRICT_KERNEL_RWX enabled, we want to split the
linear mapping at the text/data boundary so we can map the kernel
text read only.

Currently we always use a small page at the text/data boundary, even
when that's not necessary:

  Mapped 0x0000000000000000-0x0000000000e00000 with 2.00 MiB pages
  Mapped 0x0000000000e00000-0x0000000001000000 with 64.0 KiB pages
  Mapped 0x0000000001000000-0x0000000040000000 with 2.00 MiB pages

This is because the check that the mapping crosses the __init_begin
boundary is too strict, it also returns true when we map exactly up to
the boundary.

So fix it to check that the mapping would actually map past
__init_begin, and with that we see:

  Mapped 0x0000000000000000-0x0000000040000000 with 2.00 MiB pages
  Mapped 0x0000000040000000-0x0000000100000000 with 1.00 GiB pages
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When we have CONFIG_STRICT_KERNEL_RWX enabled, we want to split the
linear mapping at the text/data boundary so we can map the kernel text
read only.

But the current logic uses small pages for the entire text section,
regardless of whether a larger page size would fit. eg. with the
boundary at 16M we could use 2M pages, but instead we use 64K pages up
to the 16M boundary:

  Mapped 0x0000000000000000-0x0000000001000000 with 64.0 KiB pages
  Mapped 0x0000000001000000-0x0000000040000000 with 2.00 MiB pages
  Mapped 0x0000000040000000-0x0000000100000000 with 1.00 GiB pages

This is because the test is checking if addr is < __init_begin
and addr + mapping_size is >= _stext. But that is true for all pages
between _stext and __init_begin.

Instead what we want to check is if we are crossing the text/data
boundary, which is at __init_begin. With that fixed we see:

  Mapped 0x0000000000000000-0x0000000000e00000 with 2.00 MiB pages
  Mapped 0x0000000000e00000-0x0000000001000000 with 64.0 KiB pages
  Mapped 0x0000000001000000-0x0000000040000000 with 2.00 MiB pages
  Mapped 0x0000000040000000-0x0000000100000000 with 1.00 GiB pages

ie. we're correctly using 2MB pages below __init_begin, but we still
drop down to 64K pages unnecessarily at the boundary.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When we have CONFIG_STRICT_KERNEL_RWX enabled, we try to split the
kernel linear (1:1) mapping so that the kernel text is in a separate
page to kernel data, so we can mark the former read-only.

We could achieve that just by always using 64K pages for the linear
mapping, but we try to be smarter. Instead we use huge pages when
possible, and only switch to smaller pages when necessary.

However we have an off-by-one bug in that logic, which causes us to
calculate the wrong boundary between text and data.

For example with the end of the kernel text at 16M we see:

  radix-mmu: Mapped 0x0000000000000000-0x0000000001200000 with 64.0 KiB pages
  radix-mmu: Mapped 0x0000000001200000-0x0000000040000000 with 2.00 MiB pages
  radix-mmu: Mapped 0x0000000040000000-0x0000000100000000 with 1.00 GiB pages

ie. we mapped from 0 to 18M with 64K pages, even though the boundary
between text and data is at 16M.

With the fix we see we're correctly hitting the 16M boundary:

  radix-mmu: Mapped 0x0000000000000000-0x0000000001000000 with 64.0 KiB pages
  radix-mmu: Mapped 0x0000000001000000-0x0000000040000000 with 2.00 MiB pages
  radix-mmu: Mapped 0x0000000040000000-0x0000000100000000 with 1.00 GiB pages
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Currently, we expect to be able to reach ftrace_caller() from all
ftrace-enabled functions through a single relative branch. With large
kernel configs, we see functions outside of 32MB of ftrace_caller()
causing ftrace_init() to bail.

In such configurations, gcc/ld emits two types of trampolines for mcount():
1. A long_branch, which has a single branch to mcount() for functions that
   are one hop away from mcount():
	c0000000019e8544 <00031b56.long_branch._mcount>:
	c0000000019e8544:	4a 69 3f ac 	b       c00000000007c4f0 <._mcount>

2. A plt_branch, for functions that are farther away from mcount():
	c0000000051f33f8 <0008ba04.plt_branch._mcount>:
	c0000000051f33f8:	3d 82 ff a4 	addis   r12,r2,-92
	c0000000051f33fc:	e9 8c 04 20 	ld      r12,1056(r12)
	c0000000051f3400:	7d 89 03 a6 	mtctr   r12
	c0000000051f3404:	4e 80 04 20 	bctr

We can reuse those trampolines for ftrace if we can have those
trampolines go to ftrace_caller() instead. However, with ABIv2, we
cannot depend on r2 being valid. As such, we use only the long_branch
trampolines by patching those to instead branch to ftrace_caller or
ftrace_regs_caller.

In addition, we add additional trampolines around .text and .init.text
to catch locations that are covered by the plt branches. This allows
ftrace to work with most large kernel configurations.

For now, we always patch the trampolines to go to ftrace_regs_caller,
which is slightly inefficient. This can be optimized further at a later
point.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

WARNING: CPU: 12 PID: 4322 at /arch/powerpc/mm/pgtable-book3s64.c:76 set_pmd_at+0x4c/0x2b0
 Modules linked in:
 CPU: 12 PID: 4322 Comm: qemu-system-ppc Tainted: G        W         4.19.0-rc3-00758-g8f0c636b0542 #36
 NIP:  c0000000000872fc LR: c000000000484eec CTR: 0000000000000000
 REGS: c000003fba876fe0 TRAP: 0700   Tainted: G        W          (4.19.0-rc3-00758-g8f0c636b0542)
 MSR:  900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]>  CR: 24282884  XER: 00000000
 CFAR: c000000000484ee8 IRQMASK: 0
 GPR00: c000000000484eec c000003fba877268 c000000001f0ec00 c000003fbd229f80
 GPR04: 00007c8fe8e00000 c000003f864c5a38 860300853e0000c0 0000000000000080
 GPR08: 0000000080000000 0000000000000001 0401000000000080 0000000000000001
 GPR12: 0000000000002000 c000003fffff5400 c000003fce292000 00007c9024570000
 GPR16: 0000000000000000 0000000000ffffff 0000000000000001 c000000001885950
 GPR20: 0000000000000000 001ffffc0004807c 0000000000000008 c000000001f49d05
 GPR24: 00007c8fe8e00000 c0000000020f2468 ffffffffffffffff c000003fcd33b090
 GPR28: 00007c8fe8e00000 c000003fbd229f80 c000003f864c5a38 860300853e0000c0
 NIP [c0000000000872fc] set_pmd_at+0x4c/0x2b0
 LR [c000000000484eec] do_huge_pmd_numa_page+0xb1c/0xc20
 Call Trace:
 [c000003fba877268] [c00000000045931c] mpol_misplaced+0x1bc/0x230 (unreliable)
 [c000003fba8772c8] [c000000000484eec] do_huge_pmd_numa_page+0xb1c/0xc20
 [c000003fba877398] [c00000000040d344] __handle_mm_fault+0x5e4/0x2300
 [c000003fba8774d8] [c00000000040f400] handle_mm_fault+0x3a0/0x420
 [c000003fba877528] [c0000000003ff6f4] __get_user_pages+0x2e4/0x560
 [c000003fba877628] [c000000000400314] get_user_pages_unlocked+0x104/0x2a0
 [c000003fba8776c8] [c000000000118f44] __gfn_to_pfn_memslot+0x284/0x6a0
 [c000003fba877748] [c0000000001463a0] kvmppc_book3s_radix_page_fault+0x360/0x12d0
 [c000003fba877838] [c000000000142228] kvmppc_book3s_hv_page_fault+0x48/0x1300
 [c000003fba877988] [c00000000013dc08] kvmppc_vcpu_run_hv+0x1808/0x1b50
 [c000003fba877af8] [c000000000126b44] kvmppc_vcpu_run+0x34/0x50
 [c000003fba877b18] [c000000000123268] kvm_arch_vcpu_ioctl_run+0x288/0x2d0
 [c000003fba877b98] [c00000000011253c] kvm_vcpu_ioctl+0x1fc/0x8c0
 [c000003fba877d08] [c0000000004e9b24] do_vfs_ioctl+0xa44/0xae0
 [c000003fba877db8] [c0000000004e9c44] ksys_ioctl+0x84/0xf0
 [c000003fba877e08] [c0000000004e9cd8] sys_ioctl+0x28/0x80

We removed the pte_protnone check earlier with the understanding that we
mark the pte invalid before the set_pte/set_pmd usage. But the huge pmd
autonuma still use the set_pmd_at directly. This is ok because a protnone pte
won't have translation cache in TLB.

Fixes: da7ad366 ("powerpc/mm/book3s: Update pmd_present to look at _PAGE_PRESENT bit")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Some of our Makefiles don't do the right thing when building the
selftests with O=, fix them up.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

If CONFIG_PPC_SPLPAR is not selected, steal_time will always
be NUL, so accounting it is pointless
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

scaled cputime is only meaningfull when the processor has
SPURR and/or PURR, which means only on PPC64.

Removing it on PPC32 significantly reduces the size of
vtime_account_system() and vtime_account_idle() on an 8xx:

Before:
00000000 l     F .text	000000a8 vtime_delta
00000280 g     F .text	0000010c vtime_account_system
0000038c g     F .text	00000048 vtime_account_idle

After:
(vtime_delta gets inlined inside the two functions)
000001d8 g     F .text	000000a0 vtime_account_system
00000278 g     F .text	00000038 vtime_account_idle

In terms of performance, we also get approximatly 7% improvement on
task switch. The following small benchmark app is run with perf stat:

void *thread(void *arg)
{
	int i;

	for (i = 0; i < atoi((char*)arg); i++)
		pthread_yield();
}

int main(int argc, char **argv)
{
	pthread_t th1, th2;

	pthread_create(&th1, NULL, thread, argv[1]);
	pthread_create(&th2, NULL, thread, argv[1]);
	pthread_join(th1, NULL);
	pthread_join(th2, NULL);

	return 0;
}

Before the patch:

 Performance counter stats for 'chrt -f 98 ./sched 100000' (50 runs):

       8228.476465      task-clock (msec)         #    0.954 CPUs utilized            ( +-  0.23% )
            200004      context-switches          #    0.024 M/sec                    ( +-  0.00% )

After the patch:

 Performance counter stats for 'chrt -f 98 ./sched 100000' (50 runs):

       7649.070444      task-clock (msec)         #    0.955 CPUs utilized            ( +-  0.27% )
            200004      context-switches          #    0.026 M/sec                    ( +-  0.00% )
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

scaled cputime is only meaningfull when the processor has
SPURR and/or PURR, which means only on PPC64.

In preparation of the following patch that will remove
CONFIG_ARCH_HAS_SCALED_CPUTIME on PPC32, this patch moves
all scaled cputing accounting logic into dedicated functions.

This patch doesn't change any functionality. It's only code
reorganisation.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Generic implementation fails to remove breakpoints after init
when CONFIG_STRICT_KERNEL_RWX is selected:

[   13.251285] KGDB: BP remove failed: c001c338
[   13.259587] kgdbts: ERROR PUT: end of test buffer on 'do_fork_test' line 8 expected OK got $E14#aa
[   13.268969] KGDB: re-enter exception: ALL breakpoints killed
[   13.275099] CPU: 0 PID: 1 Comm: init Not tainted 4.18.0-g82bbb913ffd8 #860
[   13.282836] Call Trace:
[   13.285313] [c60e1ba0] [c0080ef0] kgdb_handle_exception+0x6f4/0x720 (unreliable)
[   13.292618] [c60e1c30] [c000e97c] kgdb_handle_breakpoint+0x3c/0x98
[   13.298709] [c60e1c40] [c000af54] program_check_exception+0x104/0x700
[   13.305083] [c60e1c60] [c000e45c] ret_from_except_full+0x0/0x4
[   13.310845] [c60e1d20] [c02a22ac] run_simple_test+0x2b4/0x2d4
[   13.316532] [c60e1d30] [c0081698] put_packet+0xb8/0x158
[   13.321694] [c60e1d60] [c00820b4] gdb_serial_stub+0x230/0xc4c
[   13.327374] [c60e1dc0] [c0080af8] kgdb_handle_exception+0x2fc/0x720
[   13.333573] [c60e1e50] [c000e928] kgdb_singlestep+0xb4/0xcc
[   13.339068] [c60e1e70] [c000ae1c] single_step_exception+0x90/0xac
[   13.345100] [c60e1e80] [c000e45c] ret_from_except_full+0x0/0x4
[   13.350865] [c60e1f40] [c000e11c] ret_from_syscall+0x0/0x38
[   13.356346] Kernel panic - not syncing: Recursive entry to debugger

This patch creates powerpc specific version of
kgdb_arch_set_breakpoint() and kgdb_arch_remove_breakpoint()
using patch_instruction()

Fixes: 1e0fc9d1 ("powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

ipic_get_mcp_status() is used by targets implementing NMI
watchdog in target specific machine check handler in order
to known whether a machine check results from a watchdog
NMI reset.

In case of very early machine check, primary_ipic pointer
might not have been set yet, so ipic_get_mcp_status() needs
to check it for nullity before using it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch fixes the following warnings (obtained with make W=1).

arch/powerpc/mm/slice.c: In function 'slice_range_to_mask':
arch/powerpc/mm/slice.c:73:12: error: comparison is always true due to limited range of data type [-Werror=type-limits]
  if (start < SLICE_LOW_TOP) {
            ^
arch/powerpc/mm/slice.c:81:20: error: comparison is always false due to limited range of data type [-Werror=type-limits]
  if ((start + len) > SLICE_LOW_TOP) {
                    ^
arch/powerpc/mm/slice.c: In function 'slice_mask_for_free':
arch/powerpc/mm/slice.c:136:17: error: comparison is always true due to limited range of data type [-Werror=type-limits]
  if (high_limit <= SLICE_LOW_TOP)
                 ^
arch/powerpc/mm/slice.c: In function 'slice_check_range_fits':
arch/powerpc/mm/slice.c:185:12: error: comparison is always true due to limited range of data type [-Werror=type-limits]
  if (start < SLICE_LOW_TOP) {
            ^
arch/powerpc/mm/slice.c:195:39: error: comparison is always false due to limited range of data type [-Werror=type-limits]
  if (SLICE_NUM_HIGH && ((start + len) > SLICE_LOW_TOP)) {
                                       ^
arch/powerpc/mm/slice.c: In function 'slice_scan_available':
arch/powerpc/mm/slice.c:306:11: error: comparison is always true due to limited range of data type [-Werror=type-limits]
  if (addr < SLICE_LOW_TOP) {
           ^
arch/powerpc/mm/slice.c: In function 'get_slice_psize':
arch/powerpc/mm/slice.c:709:11: error: comparison is always true due to limited range of data type [-Werror=type-limits]
  if (addr < SLICE_LOW_TOP) {
           ^
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch fixes the following warnings (obtained with make W=1).

arch/powerpc/mm/slice.c: At top level:
arch/powerpc/mm/slice.c:682:15: error: no previous prototype for 'arch_get_unmapped_area' [-Werror=missing-prototypes]
 unsigned long arch_get_unmapped_area(struct file *filp,
               ^
arch/powerpc/mm/slice.c:692:15: error: no previous prototype for 'arch_get_unmapped_area_topdown' [-Werror=missing-prototypes]
 unsigned long arch_get_unmapped_area_topdown(struct file *filp,
               ^
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add a trace point for tlbia (Translation Lookaside Buffer Invalidate
All) instruction.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

commit 0428491c ("powerpc/mm: Trace tlbie(l) instructions")
added tracepoints for tlbie calls, but _tlbil_va() was forgotten

Fixes: 0428491c ("powerpc/mm: Trace tlbie(l) instructions")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Since commit bd0dbb73 ("powerpc/mm/books3s: Add new pte bit to
mark pte temporarily invalid."), _PAGE_PRESENT doesn't mean exactly
that a page is present. A page is also considered preset when
_PAGE_INVALID is set.

This patch changes the meaning of "present" and adds a status "valid"
associated to the _PAGE_PRESENT flag.

Fixes: bd0dbb73 ("powerpc/mm/books3s: Add new pte bit to mark pte temporarily invalid.")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch exports the raw per-CPU VPA data via debugfs.
A per-CPU file is created which exports the VPA data of
that CPU to help debug some of the VPA related issues or
to analyze the per-CPU VPA related statistics.

v3: Removed offline CPU check.

v2: Included offline CPU check and other review comments.
Signed-off-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This adds a test to verify proper functioning of the rfi flush
capability implemented to mitigate meltdown. The test works by
measuring the number of L1d cache misses encountered while loading
data from memory. Across a system call, since the L1d cache is flushed
when rfi_flush is enabled, the number of cache misses is expected to
be relative to the number of cachelines corresponding to the data
being loaded.

The current system setting is reflected via powerpc/rfi_flush under
debugfs (assumed to be /sys/kernel/debug/). This test verifies the
expected result with rfi_flush enabled as well as when it is disabled.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Add SPDX tags, clang format, skip if the debugfs is missing, use
 __u64 and SANE_USERSPACE_TYPES to avoid printf() build errors.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

... so that it can be used by others.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

module_frob_arch_sections() is called before the module is moved to its
final location. The function descriptor section addresses we are setting
here are thus invalid. Fix this by processing opd section during
module_finalize()

Fixes: 5633e85b ("powerpc64: Add .opd based function descriptor dereference")
Cc: stable@vger.kernel.org # v4.16
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We implement regs_set_return_value() and override_function_with_return()
for this purpose.

On powerpc, a return from a function (blr) just branches to the location
contained in the link register. So, we can just update pt_regs rather
than redirecting execution to a dummy function that returns.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In the recent commit 8b78fdb0 ("powerpc/time: Use
clockevents_register_device(), fixing an issue with large
decrementer") we changed the way we initialise the decrementer
clockevent(s).

We no longer initialise the mult & shift values of
decrementer_clockevent itself.

This has the effect of breaking PR KVM, because it uses those values
in kvmppc_emulate_dec(). The symptom is guest kernels spin forever
mid-way through boot.

For now fix it by assigning back to decrementer_clockevent the mult
and shift values.

Fixes: 8b78fdb0 ("powerpc/time: Use clockevents_register_device(), fixing an issue with large decrementer")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

I'm pretty sure this is dead code, it's only used by the a.out core
dump code, and we don't support a.out. We should remove it.

But while it's in the tree it should be using the ABI version of
pt_regs which is called user_pt_regs in the kernel, because the whole
struct is written to the core dump and so its size shouldn't change.

Note this isn't a uapi header so we don't need an ifdef.

Fixes: 002af939 ("powerpc: Split user/kernel definitions of struct pt_regs")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

My recent patch to split pt_regs between user and kernel missed
the usage in struct sigcontext.

Because this is a user visible struct it should be using the user
visible definition, which when we're building for the kernel is called
struct user_pt_regs.

As far as I can see this hasn't actually caused a bug (yet), because
we don't use the sizeof() the sigcontext->regs anywhere. But we should
still fix it to avoid confusion and future bugs.

Fixes: 002af939 ("powerpc: Split user/kernel definitions of struct pt_regs")
Reported-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

GCC 4.6 is the minimum supported now.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Back when I added -Werror in commit ba55bd74 ("powerpc: Add
configurable -Werror for arch/powerpc") I did it by adding it to most
of the arch Makefiles.

At the time we excluded math-emu, because apparently it didn't build
cleanly. But that seems to have been fixed somewhere in the interim.

So move the -Werror addition to the top-level of the arch, this saves
us from repeating it in every Makefile and means we won't forget to
add it to any new sub-dirs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This is a nice cleanup, arch/powerpc/Makefile is long and messy so
moving this out helps a little.

It also allows us to do:

  $ make arch/powerpc

Which can be helpful if you just want to compile test some changes to
arch code and not link everything.

Finally it also gives us a single place to do subdir-cc-flags
assignments which affect the whole of arch/powerpc, which we will do
in a future patch.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

There's some antiquated debug output that's trying
to do a hand-made hexdump and turning into horrible
1-byte-per-line output these days.

Use print_hex_dump() instead
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

do_exit() already includes a test to panic() is in_interrupt()

This patch removes powerpc one which is redundant.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When creating the boot-time FDT from an actual Open Firmware live
tree, let's generate "phandle" properties for the phandles instead
of the old deprecated "linux,phandle".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Unsplit warning printf()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

prom_init.c must not modify the kernel image outside
of the .bss.prominit section. Thus make sure that
prom_init.o doesn't have anything in any of these:

	.data
	.bss
	.init.data
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This makes __prombss its own section, and for now store
it in .bss.

This will give us the ability later to store it elsewhere
and/or free it after boot (it's about 8KB).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

As they are no longer used past the end of prom_init
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Make the existing initialized definition constant and copy
it to a __prombss copy
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Initialize it dynamically instead of statically
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We removed support for running under any OPAL version
earlier than v3 in 2015 (they never saw the light of day
anyway), but we kept some leftovers of this support in
prom_init.c, so let's take it out.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This replaces all occurrences of __initdata for uninitialized
data with a new __prombss

Currently __promdata is defined to be __initdata but we'll
eventually change that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Adds a driver that implements support for enabling and accessing PAPR
SCM regions. Unfortunately due to how the PAPR interface works we can't
use the existing of_pmem driver (yet) because:

 a) The guest is required to use the H_SCM_BIND_MEM h-call to add
    add the SCM region to it's physical address space, and
 b) There is currently no mechanism for relating a bare of_pmem region
    to the backing DIMM (or not-a-DIMM for our case).

Both of these are easily handled by rolling the functionality into a
seperate driver so here we are...
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>