As all bt packets are priority traffic during bt scan, wifi
will get disconnected when bt scan lasts for few seconds. Fix
this by allocating 10% of bt period time (4.5ms) to wifi fully.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The beacon sent gating doesn't seem to work with any combination
of flags.  Thus, buffered frames tend to stay buffered forever,
using up tx descriptors.

Instead, use the DBA gating and hold transmission of the buffered
frames until 80% of the beacon interval has elapsed using the ready
time.  This fixes the following error in AP mode:

   ath5k phy0: no further txbuf available, dropping packet

Add a comment to acknowledge that this isn't the best solution.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When using the external sleep clock in AP mode, the
TSF increments too quickly, causing beacon interval
to be much lower than it is supposed to be, resulting
in lots of beacon-not-ready interrupts.

This fixes http://bugzilla.kernel.org/show_bug.cgi?id=14802.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211_hdrlen() should account account new HT Control field in 802.11
data frame header introduced by IEEE 802.11n standard.

According to 802.11n-2009 HT Control field is present in data frames
when both of following are met:

   1. It is QoS data frame.
   2. Order bit is set in Frame Control field.

The change might be totally compatible with legacy non-11n aware frames,
because 802.11-2007 standard states that "all QoS STAs set this subfield
to 0".
Signed-off-by: Andriy V. Tkachuk <andrit@ukr.net>
Acked-by : Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If a device has multiple MAC addresses, userspace will
need to know about that. Similarly, if it allows the
MAC addresses to vary by a bitmask.

If a driver exports multiple addresses, it is assumed
that it will be able to deal with that many different
addresses, which need not necessarily match the ones
programmed into the device; if a mask is set then the
device should deal addresses within that mask based
on an arbitrary "base address".

To test it all and show how it is used, add support
to hwsim even though it can't actually deal with
addresses different from the default.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When a TKIP key is updated, we should pass the station
pointer instead of just the address, since drivers can
use that to store their own data. We also need to pass
the virtual interface pointer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

"mac80211: move control.hw_key assignment" changed an if-else into two
separate if statments, but the if-else is needed to prevent
dereferencing a null info->control.hw_key.  This fixes avoids a lock-up
during association on my machine when using WEP.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Users wishing to tweak tx power want it to happen immediately,
try to respect that. This was tested by Lorenzo by measuring the
received signal strength from an AP with ath9k and the patch.

Changing the tx power on the AP produced these results:

1) iwconfig wlan0 txpower 20 ---> Rx power -37dbm
2) iwconfig wlan0 txpower 15 ---> Rx power -41dbm
3) iwconfig wlan0 txpower 10 ---> Rx power -45dbm
4) iwconfig wlan0 txpower 5 ---> Rx power -51dbm
5) iwconfig wlan0 txpower 0 ---> Rx power -37dbm

The result with 0 is an anomoly and would need to be
addressed through a separate patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211_associate() was rejecting (re)association attempts with EBUSY
in some cases where we are currently associated with an AP that uses
different channel from the destination AP. Fix this by passing the
current wdev to rdev_fixed_channel() in the same way that was already
done for join-IBSS and connect commands. This allows the fixedchan
check to skipped for the current wdev and allows the reassociation to
proceed.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With the v10 firmware running on 8688 HW, clearing WPA keys after setting the
WEP key prevents us from being able to associate with WEP APs.
Swapping the calling order for assoc_helper_wpa_keys() and
assoc_helper_wep_keys fixes that issue.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch moves the tx cleanup routines out of the critical
interrupt context and into the (previously known as rx) tasklet.

The main goal of this operation is to remove the extensive
usage of spin_lock_irqsaves in the generic p54common library.

The next step would be to modify p54usb to do the
rx processing inside a tasklet (just like usbnet).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds error-paths to handle pci_dma_mapping errors.

Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

First, both beacons and probe responses can be used for IBSS merge.
Next, sdata->u.ibss.bssid was always true (and thus IBSS merge was
disabled). We should use sdata->u.ibss.fixed_bssid instead.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee82011_sta_find_ibss() and ieee80211_sta_merge_ibss() are always
called with a defined state. So it's useless to check it or set it in
those function.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The Tx DMA descriptor has two kinds of flags that select RTS/CTS usage.
The first one (global for the frame) selects whether RTS/CTS or
CTS-to-self should be used, the second one enables RTS/CTS or
CTS-to-self usage for an individual multi-rate-retry entry.
Previously the code preparing the descriptor only enabled the global
flag, if the first MRR series selected the local one.
Fix this by enabling the global flag if any of the MRR entries need it.
With this patch, rate control can properly select the use of RTS/CTS
for all MRR entries except the first one, which is the default behavior.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Future code will need to look up rdev and wdev
within atomic sections, but currently we need
to lock a mutex for such lookups. Change the
list handling for both to be RCU-safe so that
we can look them up in rcu sections instead in
the future.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In an earlier commit,

    mac80211: disable software retry for now

    Pavel Roskin reported a problem that seems to be due to
    software retry of already transmitted frames. It turns
    out that we've never done that correctly, but due to
    some recent changes it now crashes in the TX code. I've
    added a comment in the patch that explains the problem
    better and also points to possible solutions -- which
    I can't implement right now.

I disabled software retry of failed/filtered frames
because it was broken. With the work of the previous
patches, it now becomes fairly easy to re-enable it
by adding a flag indicating that the frame shouldn't
be modified, but still running it through the transmit
handlers to populate the control information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When mac80211 asks a driver to encrypt a frame, it
must assign the control.hw_key pointer for it to
know which key to use etc. Currently, mac80211 does
this whenever it would software-encrypt a frame.

Change the logic of this code to assign the hw_key
pointer when selecting the key, and later check it
when deciding whether to encrypt the frame or let
it be encrypted by the hardware. This allows us to
later simply skip the encryption function since it
no longer modifies the TX control.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There's no value in setting a flag that will
never be checked after this point, this seems
to be legacy code -- I think previously the
flag was used to check whether to encrypt the
frame or not. Now, however, the flag need not
be set, and setting it actually interferes if
the frame will be processed again later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When an skb survived a round-trip through the driver
and needs to be re-used, its control information is
definitely not valid any more, the driver will have
overwritten it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This TX handler is used only for assigning the
station pointer in the control information, so
give it a better name. Also move it before rate
control.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Code directly scaling by HZ and rounding can be more efficiently
and clearly performed with msecs_to_jiffies.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When reading current ucode statistics information from debugfs, in
current implementation, it will always send a new "statistics request" to
uCode. In normal operation, uCode should report the statistics per beacon
interval. Remove this extra request to reduce the additional command exchanges
between driver and uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Flowhandler handle the communication between driver and uCode, when any
uCode error happen, we also like to know what is the status of the
flowhandler; it can help to debug flowhandler related problem.

Also adding debugfs file to dump current value of flowhandler registers.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is a w/a for a hardware bug. the h/w bug may cause the Rx bit
(bit 15 before shifting it to 31) to clear when using interrupt coalescing.

This does not mean frames are lost - their processing is just delayed until
next interrupt arrives.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For interrupt coalescing timer, the CSR_INT_COALESCING is an 8 bit
register in 32-usec unit, the range can go from 0x00 - 0xFF. set the
range and default timeout value for both calibration mode and operation mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>