- 19 Jul, 2017 40 commits
-
-
Sakari Ailus authored
If endpoint has an invalid configuration, ignore it instead of happily proceeding to use it nonetheless. Ignoring such an endpoint is better than failing since there could be multiple endpoints, only some of which are bad. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Tested-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Pavel Machek authored
If regulator returns -EPROBE_DEFER, we need to return it too, so that omap3isp will be re-probed when regulator is ready. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Pavel Machek authored
CSI-2 PHY power management is only needed for major version 15 of the ISP. Additionally, set the CCP2 PHY for previous ISP versions as well. These changes are necessary for CCP2 support. Signed-off-by:
-
Sakari Ailus authored
The omap3isp driver extracts the CSI-2 lane configuration from the V4L2 fwnode endpoint but misses the number of lanes itself. Get this information and use it in PHY configuration. Signed-off-by:
-
Sakari Ailus authored
The CSI-2 phy driver did initialise mutexes in its init function but there was no corresponding cleanup function destroying them. Fix that. Also clean up ISP module initialisation a little. Signed-off-by:
-
Sakari Ailus authored
Check that we do have a valid port in an endpoint, return an error if not. Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.co.uk> Tested-by:
-
Pavel Machek authored
Add support for CCP2 connected SMIA sensors as found on the Nokia N900. Signed-off-by:
Sebastian Reichel <sre@kernel.org> Signed-off-by:
Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Signed-off-by:
-
Sakari Ailus authored
CCP2 and CSI-1, are older single data lane serial busses. [mchehab@s-opensource.com: don't use spaces for identation] Signed-off-by:
-
Sakari Ailus authored
Just obtain it. It'll actually get used soon with CSI-1/CCP2. Signed-off-by:
-
Sakari Ailus authored
The function to parse CSI2 bus parameters was called v4l2_fwnode_endpoint_parse_csi_bus(), rename it as v4l2_fwnode_endpoint_parse_csi2_bus() in anticipation of CSI1/CCP2 support. Signed-off-by:
-
Sakari Ailus authored
Document the CSI1/CCP2 property strobe. It signifies the clock or strobe mode. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Sakari Ailus authored
In the vast majority of cases the bus type is known to the driver(s) since a receiver or transmitter can only support a single one. There are cases however where different options are possible, or the bus type cannot be automatically detected. The existing V4L2 OF support tries to figure out the bus type and parse the bus parameters based on that. This does not scale too well as there are multiple serial busses that share common properties. Some hardware also supports multiple types of busses on the same interfaces. Signed-off-by:
-
Philipp Zabel authored
If an encoder stop command is issued after the output queue has already stopped streaming, the qsequence counter has been reset to 0. Always wake up the capture queue if the output queue is not streaming. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Philipp Zabel authored
Firmware versions 2.3.10 revision 40778 and 3.1.1 revision 46072 are contained in the i.MX firmware download archives provided by NXP at http://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-3.5.7-1.0.0.bin and http://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-5.4.bin, respectively. Signed-off-by:
-
Philipp Zabel authored
Explicitly set MPEG-4 encoder class register instead of relying on the default value of 0. Signed-off-by:
-
Philipp Zabel authored
This fixes visual artifacts in the first macroblock row of encoded MPEG-4 video output caused by 8 additional lines of luma data leaking into the chroma planes of the internal reference framebuffers: the buffer size is rounded up to a multiple of 16x16 macroblock size, same as for the h.264 encoder. Signed-off-by:
-
Philipp Zabel authored
Set the field of destination buffers properly. Signed-off-by:
-
Philipp Zabel authored
CodaDx6 only accepts GOP sizes up to 60 frames, but CODA960 can handle up to 99 frames. If we disable automatic I frame generation altogether by setting GOP size to 0, we can let an application produce arbitrarily large I frame intervals using the V4L2_CID_MPEG_VIDEO_FORCE_KEY_FRAME control. Signed-off-by:
-
Philipp Zabel authored
This smatch warning: coda/coda-common.c:706 coda_s_fmt() warn: missing break? reassigning 'ctx->tiled_map_type' can be silenced by moving the ctx->tiled_map_type assignment into the breakout condition. That way the field is not reassigned when falling through to the next switch statement. Signed-off-by: -
Philipp Zabel authored
CODA7541 supports H.264 BP level 3/3.1 and MPEG-4 SP level 5/6. CODA960 supports H.264 BP level 4.0 and MPEG-4 SP level 5/6. Implement the necessary profile and level controls to let userspace know this. Signed-off-by:
-
Kevin Hilman authored
Fix potential NULL pointer dereference in the error path of memory allocation failure. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Kevin Hilman <khilman@baylibre.com> Acked-by:
-
Colin Ian King authored
Don't populate the gain tables on the stack but make them static const. Makes the object code smaller: Before: text data bss dec hex filename 7801 1408 0 9209 23f9 drivers/media/tuners/fc0012.o 8483 936 0 9419 24cb drivers/media/tuners/fc0013.o After: text data bss dec hex filename 7696 1464 0 9160 23c8 drivers/media/tuners/fc0012.o 8362 1024 0 9386 24aa drivers/media/tuners/fc0013.o Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Colin Ian King authored
Don't populate const array saa7128_regs_ntsc on the stack but insteaed make it static. Makes the object code smaller and saves nearly 840 bytes Before: text data bss dec hex filename 9218 360 0 9578 256a solo6x10-tw28.o After: text data bss dec hex filename 8237 504 0 8741 2225 solo6x10-tw28.o Signed-off-by:
Andrey Utkin <andrey_utkin@fastmail.com> Signed-off-by:
Ismael Luceno <ismael@iodev.co.uk> Signed-off-by:
-
Arnd Bergmann authored
When CONFIG_V4L2 is built as a loadable module, the new video mux driver fails to link as built-in code: drivers/media/platform/video-mux.o: In function `video_mux_remove': video-mux.c:(.text+0x24): undefined reference to `v4l2_async_unregister_subdev' drivers/media/platform/video-mux.o: In function `video_mux_probe': video-mux.c:(.text+0x800): undefined reference to `v4l2_subdev_init' video-mux.c:(.text+0xa10): undefined reference to `v4l2_async_register_subdev' This makes it use the same Kconfig dependency as all the other users of the VIDEO_V4L2_SUBDEV_API symbol. Fixes: 68803ad4 ("[media] platform: add video-multiplexer subdevice driver") Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by:Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by:Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by:Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Remove unnecessary static on local variable t_params. Such variable is initialized before being used, on every execution path throughout the function. The static has no benefit and, removing it reduces the code size. This issue was detected using Coccinelle and the following semantic patch: @bad exists@ position p; identifier x; type T; @@ static T x@p; ... x = <+...x...+> @@ identifier x; expression e; type T; position p != bad.p; @@ -static T x@p; ... when != x when strict ?x = e; In the following log you can see the difference in the code size. Also, there is a significant difference in the bss segment. This log is the output of the size command, before and after the code change: before: text data bss dec hex filename 23314 3640 832 27786 6c8a drivers/media/tuners/tuner-simple.o after: text data bss dec hex filename 23257 3552 768 27577 6bb9 drivers/media/tuners/tuner-simple.o Signed-off-by: -
Colin Ian King authored
Trivial fix to spelling mistake in v4l2_dbg debug message Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in v4l2_info message Signed-off-by:
-
Arvind Yadav authored
dma_buf_ops are not supposed to change at runtime. All functions working with dma_buf_ops provided by <linux/dma-buf.h> work with const dma_buf_ops. So mark the non-const structs as const. File size before: text data bss dec hex filename 5238 112 4 5354 14ea drivers/media/v4l2-core/videobuf2-dma-sg.o File size After adding 'const': text data bss dec hex filename 5358 0 4 5362 14f2 drivers/media/v4l2-core/videobuf2-dma-sg.o Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Acked-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Arvind Yadav authored
dma_buf_ops are not supposed to change at runtime. All functions working with dma_buf_ops provided by <linux/dma-buf.h> work with const dma_buf_ops. So mark the non-const structs as const. File size before: text data bss dec hex filename 3171 192 0 3363 d23 drivers/media/v4l2-core/videobuf2-vmalloc.o File size After adding 'const': text data bss dec hex filename 3291 80 0 3371 d2b drivers/media/v4l2-core/videobuf2-vmalloc.o Signed-off-by:
-
Arvind Yadav authored
dma_buf_ops are not supposed to change at runtime. All functions working with dma_buf_ops provided by <linux/dma-buf.h> work with const dma_buf_ops. So mark the non-const structs as const. File size before: text data bss dec hex filename 6035 272 0 6307 18a3 drivers/media/v4l2-core/videobuf2-dma-contig.o File size After adding 'const': text data bss dec hex filename 6155 160 0 6315 18ab drivers/media/v4l2-core/videobuf2-dma-contig.o Signed-off-by:
-
Bhumika Goyal authored
Declare v4l2_file_operations structure as const as it is only stored in the fops field of video_device structure. This field is of type const, so declare v4l2_file_operations structures with similar properties as const. Signed-off-by:
Bhumika Goyal <bhumirks@gmail.com> Signed-off-by:
-
