The KERNEL_SYSCALL define is not used anymore so the header can be
removed.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>

Signed-off-by: Helge Deller <deller@gmx.de>

Allow binding of user memory to the AGP GART on systems with HP
Quicksilver AGP bus. This resolves 'bind memory failed' error seen in
dmesg:

 [29.365973] [TTM] AGP Bind memory failed.
 …
 [29.367030] [drm] Forcing AGP to PCI mode

The system doesn't more fail to bind the memory, and hence not falling
back to the PCI mode (if other failures aren't detected).

This is just a simple write down from the following patches:
agp/amd-k7: Allow binding user memory to the AGP GART
agp/hp-agp: Allow binding user memory to the AGP GART
Signed-off-by: Alex Ivanov <gnidorah@p0n4ik.tk>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>

The parisc architecture does not have a pte special bit. As a result,
special mappings are handled with the VM_PFNMAP and VM_MIXEDMAP flags.
VM_MIXEDMAP mappings may or may not have a "struct page" backing. When
pfn_valid() is false, there is no "struct page" backing. Otherwise, they
are treated as normal pages.

The FireGL driver uses the VM_MIXEDMAP without a backing "struct page".
This treatment caused a panic due to a TLB data miss in
update_mmu_cache. This appeared to be in the code generated for
page_address(). We were in fact using a very circular bit of code to
determine the physical address of the PFN in various cache routines.
This wasn't valid when there was no "struct page" backing.  The needed
address can in fact be determined simply from the PFN itself without
using the "struct page".

The attached patch updates update_mmu_cache(), flush_cache_mm(),
flush_cache_range() and flush_cache_page() to check pfn_valid() and to
directly compute the PFN physical and virtual addresses.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>

Pull networking fixes from David Miller:

 1) Fix association failures not triggering a connect-failure event in
    cfg80211, from Johannes Berg.

 2) Eliminate a potential NULL deref with older iptables tools when
    configuring xt_socket rules, from Eric Dumazet.

 3) Missing RTNL locking in wireless regulatory code, from Johannes
    Berg.

 4) Fix OOPS caused by firmware loading races in ath9k_htc, from Alexey
    Khoroshilov.

 5) Fix usb URB leak in usb_8dev CAN driver, also from Alexey
    Khoroshilov.

 6) VXLAN namespace teardown fails to unregister devices, from Stephen
    Hemminger.

 7) Fix multicast settings getting dropped by firmware in qlcnic driver,
    from Sucheta Chakraborty.

 8) Add sysctl range enforcement for tcp_syn_retries, from Michal Tesar.

 9) Fix a nasty bug in bridging where an active timer would get
    reinitialized with a setup_timer() call.  From Eric Dumazet.

10) Fix use after free in new mlx5 driver, from Dan Carpenter.

11) Fix freed pointer reference in ipv6 multicast routing on namespace
    cleanup, from Hannes Frederic Sowa.

12) Some usbnet drivers report TSO and SG in their feature set, but the
    usbnet layer doesn't really support them.  From Eric Dumazet.

13) Fix crash on EEH errors in tg3 driver, from Gavin Shan.

14) Drop cb_lock when requesting modules in genetlink, from Stanislaw
    Gruszka.

15) Kernel stack leaks in cbq scheduler and af_key pfkey messages, from
    Dan Carpenter.

16) FEC driver erroneously signals NETDEV_TX_BUSY on transmit leading to
    endless loops, from Uwe Kleine-König.

17) Fix hangs from loading mvneta driver, from Arnaud Patard.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (84 commits)
  mlx5: fix error return code in mlx5_alloc_uuars()
  mvneta: Try to fix mvneta when compiled as module
  mvneta: Fix hang when loading the mvneta driver
  atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
  genetlink: fix usage of NLM_F_EXCL or NLM_F_REPLACE
  af_key: more info leaks in pfkey messages
  net/fec: Don't let ndo_start_xmit return NETDEV_TX_BUSY without link
  net_sched: Fix stack info leak in cbq_dump_wrr().
  igb: fix vlan filtering in promisc mode when not in VT mode
  ixgbe: Fix Tx Hang issue with lldpad on 82598EB
  genetlink: release cb_lock before requesting additional module
  net: fec: workaround stop tx during errata ERR006358
  qlcnic: Fix diagnostic interrupt test for 83xx adapters.
  qlcnic: Fix setting Guest VLAN
  qlcnic: Fix operation type and command type.
  qlcnic: Fix initialization of work function.
  Revert "atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring"
  atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
  net/tg3: Fix warning from pci_disable_device()
  net/tg3: Fix kernel crash
  ...

Pull MIPS fixes from Ralf Baechle:
 - BMIPS SMP fixes
 - a build fix necessary for older compilers
 - two more bugs found my Chandras' testing
 - and one more build fix

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: BMIPS: fix slave CPU booting when physical CPU is not 0
  MIPS: BMIPS: do not change interrupt routing depending on boot CPU
  MIPS: powertv: Fix arguments for free_reserved_area()
  MIPS: Set default CPU type for BCM47XX platforms
  MIPS: uapi/asm/siginfo.h: Fix GCC 4.1.2 compilation
  MIPS: Fix multiple definitions of UNCAC_BASE.

Pull Xen fixes from Konrad Rzeszutek Wilk:
 - Three fixes for ARM/ARM64 to either compile or not certain generic
   drivers
 - Fix for avoiding a potential deadlock when an user space event
   channel is destroyed.
 - Fix a workqueue resuming multiple times.

* tag 'stable/for-linus-3.11-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/tmem: do not allow XEN_TMEM on ARM64
  xen/evtchn: avoid a deadlock when unbinding an event channel
  xen/arm: enable PV control for ARM
  xen/arm64: Don't compile cpu hotplug
  xenbus: frontend resume cleanup

Merge tag 'xen-arm-3.11-rc2-warn-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen

Pull Xen ARM fix from Stefano Stabellini.

Update xen_restart to new calling convention.

* tag 'xen-arm-3.11-rc2-warn-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen:
  xen/arm,arm64: update xen_restart after ff701306 and 7b6d864b

Pull USB fixes from Greg KH:
 "Here are some tiny USB fixes for 3.11-rc4

  Nothing major, some gadget fixes, some new device ids, a new tiny
  driver for the ANT+ USB device, and a number of fixes for the mos7840
  driver that were much needed"

* tag 'usb-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: ftdi_sio: add more RT Systems ftdi devices
  usb: chipidea: fix the build error with randconfig
  usb: chipidea: cast PORTSC_PTS and DEVLC_PTS macros
  usb: gadget: udc-core: fix the typo of udc state attribute
  usb: gadget: f_phonet: remove unused preprocessor conditional
  usb: gadget: multi: fix error return code in cdc_do_config()
  USB: mos7840: fix pointer casts
  USB: mos7840: fix race in led handling
  USB: mos7840: fix device-type detection
  USB: mos7840: fix race in register handling
  USB: serial: add driver for Suunto ANT+ USB device
  usb: gadget: free opts struct on error recovery
  usb: gadget: ether: put_usb_function on unbind
  usb: musb: fix resource passed from glue layer to musb

Pull tty/serial driver fixes from Greg KH:
 "Here are 4 tiny tty and serial driver fixes for 3.11-rc4.

  Nothing big, a refcount leak, a module alias fix, and two fixes to the
  mxs-auart serial driver"

* tag 'tty-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: arc_uart: Fix module alias
  tty_port: Fix refcounting leak in tty_port_tty_hangup()
  serial/mxs-auart: increase time to wait for transmitter to become idle
  serial/mxs-auart: fix race condition in interrupt handler

Fix to return -ENOMEM from the ioremap error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the mvneta driver is compiled as module, the clock is disabled before
it's loading. This will reset the registers values and all configuration
made by the bootloader.

This patch sets the "sgmii serdes configuration" register to a magical value
found in:
https://github.com/yellowback/ubuntu-precise-armadaxp/blob/master/arch/arm/mach-armadaxp/armada_xp_family/ctrlEnv/mvCtrlEnvLib.c

With this change, the interrupts are working/generated and ethernet is
working.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the mvneta driver is compiled, it'll be loaded with clocks disabled.
This implies that the clocks should be enabled again before any register
access or it'll hang.

To fix it:
- enable clock earlier
- move timer callback after setting timer.data
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On Mon, 2013-07-29 at 08:30 -0700, Eric Dumazet wrote:
> On Mon, 2013-07-29 at 13:09 +0100, Luis Henriques wrote:
>
> >
> > I confirm that I can't reproduce the issue using this patch.
> >
>
> Thanks, I'll send a polished patch, as this one had an error if
> build_skb() returns NULL (in case sk_buff allocation fails)

Please try the following patch : It should use 2K frags instead of 4K
for normal 1500 mtu

Thanks !

[PATCH] atl1c: use custom skb allocator

We had reports ( https://bugzilla.kernel.org/show_bug.cgi?id=54021 )
that using high order pages for skb allocations is problematic for atl1c

We do not know exactly what the problem is, but we suspect that crossing
4K pages is not well supported by this hardware.

Use a custom allocator, using page allocator and 2K fragments for
optimal stack behavior. We might make this allocator generic
in future kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Luis Henriques <luis.henriques@canonical.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, it is not possible to use neither NLM_F_EXCL nor
NLM_F_REPLACE from genetlink. This is due to this checking in
genl_family_rcv_msg:

	if (nlh->nlmsg_flags & NLM_F_DUMP)

NLM_F_DUMP is NLM_F_MATCH|NLM_F_ROOT. Thus, if NLM_F_EXCL or
NLM_F_REPLACE flag is set, genetlink believes that you're
requesting a dump and it calls the .dumpit callback.

The solution that I propose is to refine this checking to
make it stricter:

	if ((nlh->nlmsg_flags & NLM_F_DUMP) == NLM_F_DUMP)

And given the combination NLM_F_REPLACE and NLM_F_EXCL does
not make sense to me, it removes the ambiguity.

There was a patch that tried to fix this some time ago (0ab03c2b
netlink: test for all flags of the NLM_F_DUMP composite) but it
tried to resolve this ambiguity in *all* existing netlink subsystems,
not only genetlink. That patch was reverted since it broke iproute2,
which is using NLM_F_ROOT to request the dump of the routing cache.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is inspired by a5cc68f3 "af_key: fix info leaks in notify
messages".  There are some struct members which don't get initialized
and could disclose small amounts of private information.
Acked-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't test for having link and let hardware deal with this situation.

Without this patch I see a machine running an -rt patched Linux being
stuck in sch_direct_xmit when it looses link while there is still a
packet to be sent. In this case the fec_enet_start_xmit routine returned
NETDEV_TX_BUSY which makes the network stack reschedule the packet and
so sch_direct_xmit calls fec_enet_start_xmit again.
I failed to reproduce a complete hang without -rt, but I think the
problem exists there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

tmem is not supported on arm or arm64 yet. Will revert this
once the Xen hypervisor supports it.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The current BMIPS SMP code assumes that the slave CPU is physical and
logical CPU 1, but on some systems such as BCM3368, the slave CPU is
physical CPU0. Fix the code to read the physical CPU (thread ID) we are
running this code on, and adjust the relocation vector address based on
it. This allows bringing up the second CPU on BCM3368 for instance.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: blogic@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/5621/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Commit 4df715aa ("MIPS: BMIPS: support booting from physical CPU other
than 0") changed the interupt routing when we are booting from physical
CPU 0, but the settings are actually correct if we are booting from
physical CPU 0 or CPU 1. Revert that specific change.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: blogic@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/5622/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Commit 6e7582bf
"MIPS: PowerTV: use free_reserved_area() to simplify code"

merged in 3.11-rc1, broke the build for the powertv defconfig with
the following build error:

arch/mips/powertv/asic/asic_devices.c: In function 'platform_release_memory':
arch/mips/powertv/asic/asic_devices.c:533:7: error: passing argument 1 of
'free_reserved_area' makes pointer from integer without a cast [-Werror]

The free_reserved_area() function expects a void * pointer for the start
address and a void * pointer for the end one.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5624/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

If neither BCM47XX_SSD nor BCM47XX_BCMA is selected, then no
CPU type is available leading to build problems. We fix
this problem by using MIPS32r1 as the default CPU type for
the BCM47XX platform.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5618/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It wasn't until GCC 4.3 I believe that the __SIZEOF_*__ predefined macros
were added.  The change below switches <uapi/asm/siginfo.h> to the
_MIPS_SZLONG macro so that compilation with e.g. GCC 4.1.2 succeeds.
This is a user API header so I think this is even more important, for
older userland support.  The change adds an unsuccessful default too, to
catch any compiler configuration oddities.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5630/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Fix build error below:

arch/mips/include/asm/mach-generic/spaces.h:29:0: warning:
"UNCAC_BASE" redefined [enabled by default]
In file included from arch/mips/include/asm/addrspace.h:13:0,
                 from arch/mips/include/asm/barrier.h:11,
                 from arch/mips/include/asm/bitops.h:18,
                 from include/linux/bitops.h:22,
                 from include/linux/kernel.h:10,
                 from include/asm-generic/bug.h:13,
                 from arch/mips/include/asm/bug.h:41,
                 from include/linux/bug.h:4,
                 from include/linux/page-flags.h:9,
                 from kernel/bounds.c:9:
arch/mips/include/asm/mach-ar7/spaces.h:20:0: note: this is the
location of the previous definition
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5583/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Unbinding an event channel (either with the ioctl or when the evtchn
device is closed) may deadlock because disable_irq() is called with
port_user_lock held which is also locked by the interrupt handler.

Think of the IOCTL_EVTCHN_UNBIND is being serviced, the routine has
just taken the lock, and an interrupt happens. The evtchn_interrupt
is invoked, tries to take the lock and spins forever.

A quick glance at the code shows that the spinlock is a local IRQ
variant. Unfortunately that does not help as "disable_irq() waits for
the interrupt handler on all CPUs to stop running.  If the irq occurs
on another VCPU, it tries to take port_user_lock and can't because
the unbind ioctl is holding it." (from David). Hence we cannot
depend on the said spinlock to protect us. We could make it a system
wide IRQ disable spinlock but there is a better way.

We can piggyback on the fact that the existence of the spinlock is
to make get_port_user() checks be up-to-date. And we can alter those
checks to not depend on the spin lock (as it's protected by u->bind_mutex
in the ioctl) and can remove the unnecessary locking (this is
IOCTL_EVTCHN_UNBIND) path.

In the interrupt handler we cannot use the mutex, but we do not
need it.

"The unbind disables the irq before making the port user stale, so when
you clear it you are guaranteed that the interrupt handler that might
use that port cannot be running." (from David).

Hence this patch removes the spinlock usage on the teardown path
and piggybacks on disable_irq happening before we muck with the
get_port_user() data. This ensures that the interrupt handler will
never run on stale data.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v1: Expanded the commit description a bit]

Make sure the reserved fields, and padding (if any), are
fully initialized.

Based upon a patch by Dan Carpenter and feedback from
Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull firewire regression fix from Stefan Richter:
 "This fixes corrupted video capture, seen with IIDC/DCAM video and
  certain buffer settings.  (Regression since v3.4 inclusive.)"

* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
  firewire: fix libdc1394/FlyCap2 iso event regression

Pull ARC fix from Vineet Gupta:
 "SMP build breakage fix"

* tag 'arc-v3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: SMP build breakage

RT Systems makes many usb serial cables based on the ftdi_sio driver for
programming various amateur radios.  This patch is a full listing of
their current product offerings and should allow these cables to all
be recognized.
Signed-off-by: Rick Farina (Zero_Chaos) <zerochaos@gentoo.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using below  configs, the compile will have error:
ERROR: "ehci_init_driver" undefined!

.config:
CONFIG_USB_CHIPIDEA=m
CONFIG_USB_CHIPIDEA_HOST=y
CONFIG_USB_CHIPIDEA_DEBUG=y

The reason is chipidea host uses symbol from ehci, but ehci
is not compiled. Let the chipidea host depend on
ehci even it is built as module.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the following build warnings on x86:

drivers/usb/chipidea/core.c: In function 'hw_phymode_configure':
drivers/usb/chipidea/core.c:226:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:230:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:243:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:246:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v3.11-rc3

Here are some fixes for v3.11-rc3. Mostly related to
the recent conversion to configfs done on the gadget
drivers, but we also have a fix for MUSB resources
on platforms which need 3 resources instead of 2, and
a fix for the sysfs_notify() call on udc-core.c which
was notifying an unexistent file.

Enable lifecyle management (reboot, shutdown...) from the toolstack
for ARM guests.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>

On ARM64, when CONFIG_XEN=y, the compilation will fail because CPU hotplug is
not yet supported with XEN. For now, disable it.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>

Only create the delayed resume workqueue if we are running in the same domain
as xenstored and issue a warning if the workqueue creation fails.

Move the work initialization to the device probe so it is done only once.
Signed-off-by: Aurelien Chartier <aurelien.chartier@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>

The name of udc state attribute file under sysfs is registered as
"state", while usb_gadget_set_state take it as "status" when it's
going to update. This patch fixes the typo.
Signed-off-by: Rong Wang <Rong.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: <stable@kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The compatibility layer which the USBF_PHONET_INCLUDED was a part of
is no longer present - the USBF_PHONET_INCLUDED is not #defined by anyone
anymore, so the ifndef is always true. Removing it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.

Introduced by commit 59835a (usb: gadget: multi: use
function framework for ACM.)

Make rndis_do_config() consistent with cdc_do_config() in the way it
handles returning the PTR_ERR(f_acm_*).
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Merge tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control fixes from Linus Walleij:
 - Driver fixes for AM33xx, SIRF and PFC pin controllers
 - Fix a compile warning from the pinctrl single-register driver
 - Fix a little nasty memory leak

* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: fix a memleak when freeing maps
  pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
  pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
  arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
  pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
  pinctrl: sirf: fix the pin number and mux bit for usp0
  pinctrl: am33xx dt binding: correct include path