- 07 Apr, 2020 35 commits
-
-
Andrea Arcangeli authored
Accurate userfaultfd WP tracking is possible by tracking exactly which virtual memory ranges were writeprotected by userland. We can't relay only on the RW bit of the mapped pagetable because that information is destroyed by fork() or KSM or swap. If we were to relay on that, we'd need to stay on the safe side and generate false positive wp faults for every swapped out page. [peterx@redhat.com: append _PAGE_UFD_WP to _PAGE_CHG_MASK] Signed-off-by:
Andrea Arcangeli <aarcange@redhat.com> Signed-off-by:
Peter Xu <peterx@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Reviewed-by:
Jerome Glisse <jglisse@redhat.com> Reviewed-by:
Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Bobby Powers <bobbypowers@gmail.com> Cc: Brian Geffon <bgeffon@google.com> Cc: David Hildenbrand <david@redhat.com> Cc: Denis Plotnikov <dplotnikov@virtuozzo.com> Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "Kirill A . Shutemov" <kirill@shutemov.name> Cc: Martin Cracauer <cracauer@cons.org> Cc: Marty McFadden <mcfadden8@llnl.gov> Cc: Maya Gokhale <gokhale2@llnl.gov> Cc: Mel Gorman <mgorman@suse.de> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Pavel Emelyanov <xemul@openvz.org> Cc: Rik van Riel <riel@redhat.com> Cc: Shaohua Li <shli@fb.com> Link: http://lkml.kernel.org/r/20200220163112.11409-4-peterx@redhat.comSigned-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Andrea Arcangeli authored
There are several cases write protection fault happens. It could be a write to zero page, swaped page or userfault write protected page. When the fault happens, there is no way to know if userfault write protect the page before. Here we just blindly issue a userfault notification for vma with VM_UFFD_WP regardless if app write protects it yet. Application should be ready to handle such wp fault. In the swapin case, always swapin as readonly. This will cause false positive userfaults. We need to decide later if to eliminate them with a flag like soft-dirty in the swap entry (see _PAGE_SWP_SOFT_DIRTY). hugetlbfs wouldn't need to worry about swapouts but and tmpfs would be handled by a swap entry bit like anonymous memory. The main problem with no easy solution to eliminate the false positives, will be if/when userfaultfd is extended to real filesystem pagecache. When the pagecache is freed by reclaim we can't leave the radix tree pinned if the inode and in turn the radix tree is reclaimed as well. The estimation is that full accuracy and lack of false positives could be easily provided only to anonymous memory (as long as there's no fork or as long as MADV_DONTFORK is used on the userfaultfd anonymous range) tmpfs and hugetlbfs, it's most certainly worth to achieve it but in a later incremental patch. [peterx@redhat.com: don't conditionally drop FAULT_FLAG_WRITE in do_swap_page] Signed-off-by:
-
Shaohua Li authored
Patch series "userfaultfd: write protection support", v6. Overview ======== The uffd-wp work was initialized by Shaohua Li [1], and later continued by Andrea [2]. This series is based upon Andrea's latest userfaultfd tree, and it is a continuous works from both Shaohua and Andrea. Many of the follow up ideas come from Andrea too. Besides the old MISSING register mode of userfaultfd, the new uffd-wp support provides another alternative register mode called UFFDIO_REGISTER_MODE_WP that can be used to listen to not only missing page faults but also write protection page faults, or even they can be registered together. At the same time, the new feature also provides a new userfaultfd ioctl called UFFDIO_WRITEPROTECT which allows the userspace to write protect a range or memory or fixup write permission of faulted pages. Please refer to the document patch "userfaultfd: wp: UFFDIO_REGISTER_MODE_WP documentation update" for more information on the new interface and what it can do. The major workflow of an uffd-wp program should be: 1. Register a memory region with WP mode using UFFDIO_REGISTER_MODE_WP 2. Write protect part of the whole registered region using UFFDIO_WRITEPROTECT, passing in UFFDIO_WRITEPROTECT_MODE_WP to show that we want to write protect the range. 3. Start a working thread that modifies the protected pages, meanwhile listening to UFFD messages. 4. When a write is detected upon the protected range, page fault happens, a UFFD message will be generated and reported to the page fault handling thread 5. The page fault handler thread resolves the page fault using the new UFFDIO_WRITEPROTECT ioctl, but this time passing in !UFFDIO_WRITEPROTECT_MODE_WP instead showing that we want to recover the write permission. Before this operation, the fault handler thread can do anything it wants, e.g., dumps the page to a persistent storage. 6. The worker thread will continue running with the correctly applied write permission from step 5. Currently there are already two projects that are based on this new userfaultfd feature. QEMU Live Snapshot: The project provides a way to allow the QEMU hypervisor to take snapshot of VMs without stopping the VM [3]. LLNL umap library: The project provides a mmap-like interface and "allow to have an application specific buffer of pages cached from a large file, i.e. out-of-core execution using memory map" [4][5]. Before posting the patchset, this series was smoke tested against QEMU live snapshot and the LLNL umap library (by doing parallel quicksort using 128 sorting threads + 80 uffd servicing threads). My sincere thanks to Marty Mcfadden and Denis Plotnikov for the help along the way. TODO ==== - hugetlbfs/shmem support - performance - more architectures - cooperate with mprotect()-allowed processes (???) - ... References ========== [1] https://lwn.net/Articles/666187/ [2] https://git.kernel.org/pub/scm/linux/kernel/git/andrea/aa.git/log/?h=userfault [3] https://github.com/denis-plotnikov/qemu/commits/background-snapshot-kvm [4] https://github.com/LLNL/umap [5] https://llnl-umap.readthedocs.io/en/develop/ [6] https://git.kernel.org/pub/scm/linux/kernel/git/andrea/aa.git/commit/?h=userfault&id=b245ecf6cf59156966f3da6e6b674f6695a5ffa5 [7] https://lkml.org/lkml/2018/11/21/370 [8] https://lkml.org/lkml/2018/12/30/64 This patch (of 19): Add helper for writeprotect check. Will use it later. Signed-off-by:Shaohua Li <shli@fb.com> Signed-off-by:
-
David Hildenbrand authored
Commit 71994620 ("virtio_balloon: replace oom notifier with shrinker") changed the behavior when deflation happens automatically. Instead of deflating when called by the OOM handler, the shrinker is used. However, the balloon is not simply some other slab cache that should be shrunk when under memory pressure. The shrinker does not have a concept of priorities yet, so this behavior cannot be configured. Eventually once that is in place, we might want to switch back after doing proper testing. There was a report that this results in undesired side effects when inflating the balloon to shrink the page cache. [1] "When inflating the balloon against page cache (i.e. no free memory remains) vmscan.c will both shrink page cache, but also invoke the shrinkers -- including the balloon's shrinker. So the balloon driver allocates memory which requires reclaim, vmscan gets this memory by shrinking the balloon, and then the driver adds the memory back to the balloon. Basically a busy no-op." The name "deflate on OOM" makes it pretty clear when deflation should happen - after other approaches to reclaim memory failed, not while reclaiming. This allows to minimize the footprint of a guest - memory will only be taken out of the balloon when really needed. Keep using the shrinker for VIRTIO_BALLOON_F_FREE_PAGE_HINT, because this has no such side effects. Always register the shrinker with VIRTIO_BALLOON_F_FREE_PAGE_HINT now. We are always allowed to reuse free pages that are still to be processed by the guest. The hypervisor takes care of identifying and resolving possible races between processing a hinting request and the guest reusing a page. In contrast to pre commit 71994620 ("virtio_balloon: replace oom notifier with shrinker"), don't add a module parameter to configure the number of pages to deflate on OOM. Can be re-added if really needed. Also, pay attention that leak_balloon() returns the number of 4k pages - convert it properly in virtio_balloon_oom_notify(). Testing done by Tyler for future reference: Test setup: VM with 16 CPU, 64GB RAM. Running Debian 10. We have a 42 GB file full of random bytes that we continually cat to /dev/null. This fills the page cache as the file is read. Meanwhile, we trigger the balloon to inflate, with a target size of 53 GB. This setup causes the balloon inflation to pressure the page cache as the page cache is also trying to grow. Afterwards we shrink the balloon back to zero (so total deflate == total inflate). Without this patch (kernel 4.19.0-5): Inflation never reaches the target until we stop the "cat file > /dev/null" process. Total inflation time was 542 seconds. The longest period that made no net forward progress was 315 seconds. Result of "grep balloon /proc/vmstat" after the test: balloon_inflate 154828377 balloon_deflate 154828377 With this patch (kernel 5.6.0-rc4+): Total inflation duration was 63 seconds. No deflate-queue activity occurs when pressuring the page-cache. Result of "grep balloon /proc/vmstat" after the test: balloon_inflate 12968539 balloon_deflate 12968539 Conclusion: This patch fixes the issue. In the test it reduced inflate/deflate activity by 12x, and reduced inflation time by 8.6x. But more importantly, if we hadn't killed the "cat file > /dev/null" process then, without the patch, the inflation process would never reach the target. [1] https://www.spinics.net/lists/linux-virtualization/msg40863.html Link: http://lkml.kernel.org/r/20200311135523.18512-2-david@redhat.com Fixes: 71994620 ("virtio_balloon: replace oom notifier with shrinker") Signed-off-by:
David Hildenbrand <david@redhat.com> Reported-by:
Tyler Sanderson <tysand@google.com> Tested-by:
David Rientjes <rientjes@google.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Cc: Wei Wang <wei.w.wang@intel.com> Cc: Alexander Duyck <alexander.h.duyck@linux.intel.com> Cc: David Rientjes <rientjes@google.com> Cc: Nadav Amit <namit@vmware.com> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by:
-
Alexander Duyck authored
Add documentation for free page reporting. Currently the only consumer is virtio-balloon, however it is possible that other drivers might make use of this so it is best to add a bit of documetation explaining at a high level how to use the API. Signed-off-by:
Alexander Duyck <alexander.h.duyck@linux.intel.com> Signed-off-by:
-
Alexander Duyck authored
In order to keep ourselves from reporting pages that are just going to be reused again in the case of heavy churn we can put a limit on how many total pages we will process per pass. Doing this will allow the worker thread to go into idle much more quickly so that we avoid competing with other threads that might be allocating or freeing pages. The logic added here will limit the worker thread to no more than one sixteenth of the total free pages in a given area per list. Once that limit is reached it will update the state so that at the end of the pass we will reschedule the worker to try again in 2 seconds when the memory churn has hopefully settled down. Again this optimization doesn't show much of a benefit in the standard case as the memory churn is minmal. However with page allocator shuffling enabled the gain is quite noticeable. Below are the results with a THP enabled version of the will-it-scale page_fault1 test showing the improvement in iterations for 16 processes or threads. Without: tasks processes processes_idle threads threads_idle 16 8283274.75 0.17 5594261.00 38.15 With: tasks processes processes_idle threads threads_idle 16 8767010.50 0.21 5791312.75 36.98 Signed-off-by:
Mel Gorman <mgorman@techsingularity.net> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: David Hildenbrand <david@redhat.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Nitesh Narayan Lal <nitesh@redhat.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Pankaj Gupta <pagupta@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Rik van Riel <riel@surriel.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Wei Wang <wei.w.wang@intel.com> Cc: Yang Zhang <yang.zhang.wz@gmail.com> Cc: wei qi <weiqi4@huawei.com> Link: http://lkml.kernel.org/r/20200211224719.29318.72113.stgit@localhost.localdomainSigned-off-by:
-
Alexander Duyck authored
Rather than walking over the same pages again and again to get to the pages that have yet to be reported we can save ourselves a significant amount of time by simply rotating the list so that when we have a full list of reported pages the head of the list is pointing to the next non-reported page. Doing this should save us some significant time when processing each free list. This doesn't gain us much in the standard case as all of the non-reported pages should be near the top of the list already. However in the case of page shuffling this results in a noticeable improvement. Below are the will-it-scale page_fault1 w/ THP numbers for 16 tasks with and without this patch. Without: tasks processes processes_idle threads threads_idle 16 8093776.25 0.17 5393242.00 38.20 With: tasks processes processes_idle threads threads_idle 16 8283274.75 0.17 5594261.00 38.15 Signed-off-by:
-
Alexander Duyck authored
Add support for the page reporting feature provided by virtio-balloon. Reporting differs from the regular balloon functionality in that is is much less durable than a standard memory balloon. Instead of creating a list of pages that cannot be accessed the pages are only inaccessible while they are being indicated to the virtio interface. Once the interface has acknowledged them they are placed back into their respective free lists and are once again accessible by the guest system. Unlike a standard balloon we don't inflate and deflate the pages. Instead we perform the reporting, and once the reporting is completed it is assumed that the page has been dropped from the guest and will be faulted back in the next time the page is accessed. Signed-off-by:
-
Alexander Duyck authored
Currently the page poisoning setting wasn't being enabled unless free page hinting was enabled. However we will need the page poisoning tracking logic as well for free page reporting. As such pull it out and make it a separate bit of config in the probe function. In addition we need to add support for the more recent init_on_free feature which expects a behavior similar to page poisoning in that we expect the page to be pre-zeroed. Signed-off-by:
-
Alexander Duyck authored
In order to pave the way for free page reporting in virtualized environments we will need a way to get pages out of the free lists and identify those pages after they have been returned. To accomplish this, this patch adds the concept of a Reported Buddy, which is essentially meant to just be the Uptodate flag used in conjunction with the Buddy page type. To prevent the reported pages from leaking outside of the buddy lists I added a check to clear the PageReported bit in the del_page_from_free_list function. As a result any reported page that is split, merged, or allocated will have the flag cleared prior to the PageBuddy value being cleared. The process for reporting pages is fairly simple. Once we free a page that meets the minimum order for page reporting we will schedule a worker thread to start 2s or more in the future. That worker thread will begin working from the lowest supported page reporting order up to MAX_ORDER - 1 pulling unreported pages from the free list and storing them in the scatterlist. When processing each individual free list it is necessary for the worker thread to release the zone lock when it needs to stop and report the full scatterlist of pages. To reduce the work of the next iteration the worker thread will rotate the free list so that the first unreported page in the free list becomes the first entry in the list. It will then call a reporting function providing information on how many entries are in the scatterlist. Once the function completes it will return the pages to the free area from which they were allocated and start over pulling more pages from the free areas until there are no longer enough pages to report on to keep the worker busy, or we have processed as many pages as were contained in the free area when we started processing the list. The worker thread will work in a round-robin fashion making its way though each zone requesting reporting, and through each reportable free list within that zone. Once all free areas within the zone have been processed it will check to see if there have been any requests for reporting while it was processing. If so it will reschedule the worker thread to start up again in roughly 2s and exit. Signed-off-by:
-
Alexander Duyck authored
There are cases where we would benefit from avoiding having to go through the allocation and free cycle to return an isolated page. Examples for this might include page poisoning in which we isolate a page and then put it back in the free list without ever having actually allocated it. This will enable us to also avoid notifiers for the future free page reporting which will need to avoid retriggering page reporting when returning pages that have been reported on. Signed-off-by:
-
Alexander Duyck authored
In order to enable the use of the zone from the list manipulator functions I will need access to the zone pointer. As it turns out most of the accessors were always just being directly passed &zone->free_area[order] anyway so it would make sense to just fold that into the function itself and pass the zone and order as arguments instead of the free area. In order to be able to reference the zone we need to move the declaration of the functions down so that we have the zone defined before we define the list manipulation functions. Since the functions are only used in the file mm/page_alloc.c we can just move them there to reduce noise in the header. Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Reviewed-by:
Pankaj Gupta <pagupta@redhat.com> Acked-by:
-
Alexander Duyck authored
Patch series "mm / virtio: Provide support for free page reporting", v17. This series provides an asynchronous means of reporting free guest pages to a hypervisor so that the memory associated with those pages can be dropped and reused by other processes and/or guests on the host. Using this it is possible to avoid unnecessary I/O to disk and greatly improve performance in the case of memory overcommit on the host. When enabled we will be performing a scan of free memory every 2 seconds while pages of sufficiently high order are being freed. In each pass at least one sixteenth of each free list will be reported. By doing this we avoid racing against other threads that may be causing a high amount of memory churn. The lowest page order currently scanned when reporting pages is pageblock_order so that this feature will not interfere with the use of Transparent Huge Pages in the case of virtualization. Currently this is only in use by virtio-balloon however there is the hope that at some point in the future other hypervisors might be able to make use of it. In the virtio-balloon/QEMU implementation the hypervisor is currently using MADV_DONTNEED to indicate to the host kernel that the page is currently free. It will be zeroed and faulted back into the guest the next time the page is accessed. To track if a page is reported or not the Uptodate flag was repurposed and used as a Reported flag for Buddy pages. We walk though the free list isolating pages and adding them to the scatterlist until we either encounter the end of the list or have processed at least one sixteenth of the pages that were listed in nr_free prior to us starting. If we fill the scatterlist before we reach the end of the list we rotate the list so that the first unreported page we encounter is moved to the head of the list as that is where we will resume after we have freed the reported pages back into the tail of the list. Below are the results from various benchmarks. I primarily focused on two tests. The first is the will-it-scale/page_fault2 test, and the other is a modified version of will-it-scale/page_fault1 that was enabled to use THP. I did this as it allows for better visibility into different parts of the memory subsystem. The guest is running with 32G for RAM on one node of a E5-2630 v3. The host has had some features such as CPU turbo disabled in the BIOS. Test page_fault1 (THP) page_fault2 Name tasks Process Iter STDEV Process Iter STDEV Baseline 1 1012402.50 0.14% 361855.25 0.81% 16 8827457.25 0.09% 3282347.00 0.34% Patches Applied 1 1007897.00 0.23% 361887.00 0.26% 16 8784741.75 0.39% 3240669.25 0.48% Patches Enabled 1 1010227.50 0.39% 359749.25 0.56% 16 8756219.00 0.24% 3226608.75 0.97% Patches Enabled 1 1050982.00 4.26% 357966.25 0.14% page shuffle 16 8672601.25 0.49% 3223177.75 0.40% Patches enabled 1 1003238.00 0.22% 360211.00 0.22% shuffle w/ RFC 16 8767010.50 0.32% 3199874.00 0.71% The results above are for a baseline with a linux-next-20191219 kernel, that kernel with this patch set applied but page reporting disabled in virtio-balloon, the patches applied and page reporting fully enabled, the patches enabled with page shuffling enabled, and the patches applied with page shuffling enabled and an RFC patch that makes used of MADV_FREE in QEMU. These results include the deviation seen between the average value reported here versus the high and/or low value. I observed that during the test memory usage for the first three tests never dropped whereas with the patches fully enabled the VM would drop to using only a few GB of the host's memory when switching from memhog to page fault tests. Any of the overhead visible with this patch set enabled seems due to page faults caused by accessing the reported pages and the host zeroing the page before giving it back to the guest. This overhead is much more visible when using THP than with standard 4K pages. In addition page shuffling seemed to increase the amount of faults generated due to an increase in memory churn. The overehad is reduced when using MADV_FREE as we can avoid the extra zeroing of the pages when they are reintroduced to the host, as can be seen when the RFC is applied with shuffling enabled. The overall guest size is kept fairly small to only a few GB while the test is running. If the host memory were oversubscribed this patch set should result in a performance improvement as swapping memory in the host can be avoided. A brief history on the background of free page reporting can be found at: https://lore.kernel.org/lkml/29f43d5796feed0dec8e8bb98b187d9dac03b900.camel@linux.intel.com/ This patch (of 9): Move the head/tail adding logic out of the shuffle code and into the __free_one_page function since ultimately that is where it is really needed anyway. By doing this we should be able to reduce the overhead and can consolidate all of the list addition bits in one spot. Signed-off-by: -
Huang Ying authored
Some comments for MADV_FREE is revised and added to help people understand the MADV_FREE code, especially the page flag, PG_swapbacked. This makes page_is_file_cache() isn't consistent with its comments. So the function is renamed to page_is_file_lru() to make them consistent again. All these are put in one patch as one logical change. Suggested-by:
Johannes Weiner <hannes@cmpxchg.org> Suggested-by:
"Huang, Ying" <ying.huang@intel.com> Signed-off-by:
Michal Hocko <mhocko@kernel.org> Acked-by:
Pankaj Gupta <pankaj.gupta.linux@gmail.com> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Minchan Kim <minchan@kernel.org> Cc: Hugh Dickins <hughd@google.com> Cc: Rik van Riel <riel@surriel.com> Link: http://lkml.kernel.org/r/20200317100342.2730705-1-ying.huang@intel.comSigned-off-by:
-
Li Chen authored
This updates get_user_pages()'s argument in ksm_test_exit()'s comment Signed-off-by:
Li Chen <chenli@uniontech.com> Signed-off-by:
-
Matthew Wilcox (Oracle) authored
Commit e496cf3d ("thp: introduce CONFIG_TRANSPARENT_HUGE_PAGECACHE") notes that it should be reverted when the PowerPC problem was fixed. The commit fixing the PowerPC problem (953c66c2) did not revert the commit; instead setting CONFIG_TRANSPARENT_HUGE_PAGECACHE to the same as CONFIG_TRANSPARENT_HUGEPAGE. Checking with Kirill and Aneesh, this was an oversight, so remove the Kconfig symbol and undo the work of commit e496cf3d. Signed-off-by:
Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com> Link: http://lkml.kernel.org/r/20200318140253.6141-6-willy@infradead.orgSigned-off-by:
-
Matthew Wilcox (Oracle) authored
If THP is disabled, find_subpage() can become a no-op by using hpage_nr_pages() instead of compound_nr(). hpage_nr_pages() embeds a check for PageTail, so we can drop the check here. Signed-off-by:
Christoph Hellwig <hch@lst.de> Acked-by:
-
David Rientjes authored
The thp_fault_fallback and thp_file_fallback vmstats are incremented if either the hugepage allocation fails through the page allocator or the hugepage charge fails through mem cgroup. This patch leaves this field untouched but adds two new fields, thp_{fault,file}_fallback_charge, which is incremented only when the mem cgroup charge fails. This distinguishes between attempted hugepage allocations that fail due to fragmentation (or low memory conditions) and those that fail due to mem cgroup limits. That can be used to determine the impact of fragmentation on the system by excluding faults that failed due to memcg usage. Signed-off-by:Yang Shi <yang.shi@linux.alibaba.com> Acked-by:
-
David Rientjes authored
The existing thp_fault_fallback indicates when thp attempts to allocate a hugepage but fails, or if the hugepage cannot be charged to the mem cgroup hierarchy. Extend this to shmem as well. Adds a new thp_file_fallback to complement thp_file_alloc that gets incremented when a hugepage is attempted to be allocated but fails, or if it cannot be charged to the mem cgroup hierarchy. Additionally, remove the check for CONFIG_TRANSPARENT_HUGE_PAGECACHE from shmem_alloc_hugepage() since it is only called with this configuration option. Signed-off-by:
-
Yang Shi authored
Currently the migration code doesn't migrate PG_readahead flag. Theoretically this would incur slight performance loss as the application might have to ramp its readahead back up again. Even though such problem happens, it might be hidden by something else since migration is typically triggered by compaction and NUMA balancing, any of which should be more noticeable. Migrate the flag after end_page_writeback() since it may clear PG_reclaim flag, which is the same bit as PG_readahead, for the new page. [akpm@linux-foundation.org: tweak comment] Signed-off-by:
-
Wei Yang authored
It can currently happen that we store the status of a page twice: * Once we detect that it is already on the target node * Once we moved a bunch of pages, and a page that's already on the target node is contained in the current interval. Let's simplify the code and always call do_move_pages_to_node() in case we did not queue a page for migration. Note that pages that are already on the target node are not added to the pagelist and are, therefore, ignored by do_move_pages_to_node() - there is no functional change. The status of such a page is now only stored once. [david@redhat.com rephrase changelog] Signed-off-by:
Wei Yang <richardw.yang@linux.intel.com> Signed-off-by:
Michal Hocko <mhocko@suse.com> Link: http://lkml.kernel.org/r/20200214003017.25558-5-richardw.yang@linux.intel.comSigned-off-by:
-
Wei Yang authored
When pagelist is empty, it is not necessary to do the move and store. Also it consolidate the empty list check in one place. Signed-off-by:
-
Wei Yang authored
Usually, do_move_pages_to_node() and store_status() are used in combination. We have three similar call sites. Let's provide a wrapper for both function calls - move_pages_and_store_status - to make the calling code easier to maintain and fix (as noted by Yang Shi, the return value handling of do_move_pages_to_node() has a flaw). [david@redhat.com rephrase changelog] Signed-off-by:
-
Wei Yang authored
Patch series "cleanup on do_pages_move()", v5. The logic in do_pages_move() is a little mess for audience to read and has some potential error on handling the return value. Especially there are three calls on do_move_pages_to_node() and store_status() with almost the same form. This patch set tries to make the code a little friendly for audience by consolidate the calls. This patch (of 4): At this point, we always have i >= start. If i == start, store_status() will return 0. So we can drop the check for i > start. [david@redhat.com rephrase changelog] Signed-off-by:
-
Michal Hocko authored
While it might be really clear to MM developers that gfp reclaim modifiers are applicable only to sleepable allocations (those with __GFP_DIRECT_RECLAIM) it seems that actual users of the API are not always sure. Make it explicit that they are not applicable for GFP_NOWAIT or GFP_ATOMIC allocations which are the most commonly used non-sleepable allocation masks. Signed-off-by:
Joel Fernandes (Google) <joel@joelfernandes.org> Acked-by:
Paul E. McKenney <paulmck@kernel.org> Acked-by:
-
Qiujun Huang authored
There is a typo in comment, fix it. "exeeds" -> "exceeds" Signed-off-by:
Qiujun Huang <hqjagain@gmail.com> Signed-off-by:
-
Anshuman Khandual authored
It is unlikely that an inaccessible VMA without required permission flags will get a page fault. Hence lets just append unlikely() directive to such checks in order to improve performance while also standardizing it across various platforms. Signed-off-by:
Anshuman Khandual <anshuman.khandual@arm.com> Signed-off-by:
-
Anshuman Khandual authored
This replaces all remaining open encodings with vma_is_anonymous(). Signed-off-by:
-
Anshuman Khandual authored
This replaces all remaining open encodings with is_vm_hugetlb_page(). Signed-off-by:
-
Anshuman Khandual authored
Lets move vma_is_accessible() helper to include/linux/mm.h which makes it available for general use. While here, this replaces all remaining open encodings for VMA access check with vma_is_accessible(). Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Acked-by:
Guo Ren <guoren@kernel.org> Acked-by:
-
Anshuman Khandual authored
Patch series "mm/vma: Use all available wrappers when possible", v2. Apart from adding a VMA flag readable name for trace purpose, this series does some open encoding replacements with availabe VMA specific wrappers. This skips VM_HUGETLB check in vma_migratable() as its already being done with another patch (https://patchwork.kernel.org/patch/11347831/) which is yet to be merged. This patch (of 4): This just adds the missing readable name for VM_SYNC. Signed-off-by:
-
Li Xinhai authored
Set ->vm_next and ->vm_prev to NULL to prevent potential misuse from the new duplicated vma. Currently, only in fork path there are misuse for handling anon_vma. No other bugs been revealed with this patch applied. Signed-off-by:
Li Xinhai <lixinhai.lxh@gmail.com> Signed-off-by:
-
Li Xinhai authored
This reverts commit 4e4a9eb9 ("mm/rmap.c: reuse mergeable anon_vma as parent when fork"). In dup_mmap(), anon_vma_fork() is called for attaching anon_vma and parameter 'tmp' (i.e., the new vma of child) has same ->vm_next and ->vm_prev as its parent vma. That causes the anon_vma used by parent been mistakenly shared by child (In anon_vma_clone(), the code added by that commit will do this reuse work). Besides this issue, the design of reusing anon_vma from vma which has gone through fork should be avoided ([1]). So, this patch reverts that commit and maintains the consistent logic of reusing anon_vma for fork/split/merge vma. Reusing anon_vma within the process is fine. But if a vma has gone through fork(), then that vma's anon_vma should not be shared with its neighbor vma. As explained in [1], when vma gone through fork(), the check for list_is_singular(vma->anon_vma_chain) will be false, and don't share anon_vma. With current issue, one example can clarify more. Parent process do below two steps: 1. p_vma_1 is created and p_anon_vma_1 is prepared; 2. p_vma_2 is created and share p_anon_vma_1; (this is allowed, becaues p_vma_1 didn't gothrough fork()); parent process do fork(): 3. c_vma_1 is dup from p_vma_1, and has its own c_anon_vma_1 prepared; at this point, c_vma_1->anon_vma_chain has two items, one for p_anon_vma_1 and one for c_anon_vma_1; 4. c_vma_2 is dup from p_vma_2, it is not allowed to share c_anon_vma_1, because c_vma_1->anon_vma_chain has two items. [1] commit d0e9fe17 ("Simplify and comment on anon_vma re-use for anon_vma_prepare()") explains the test of "list_is_singular()". Fixes: 4e4a9eb9 ("mm/rmap.c: reuse mergeable anon_vma as parent when fork") Signed-off-by:
-
Li Xinhai authored
Patch series "mm: Fix misuse of parent anon_vma in dup_mmap path". This patchset fixes the misuse of parenet anon_vma, which mainly caused by child vma's vm_next and vm_prev are left same as its parent after duplicate vma. Finally, code reached parent vma's neighbor by referring pointer of child vma and executed wrong logic. The first two patches fix relevant issues, and the third patch sets vm_next and vm_prev to NULL when duplicate vma to prevent potential misuse in future. Effects of the first bug is that causes rmap code to check both parent and child's page table, although a page couldn't be mapped by both parent and child, because child vma has WIPEONFORK so all pages mapped by child are 'new' and not relevant to parent. Effects of the second bug is that the relationship of anon_vma of parent and child are totallyconvoluted. It would cause 'son', 'grandson', ..., etc, to share 'parent' anon_vma, which disobey the design rule of reusing anon_vma (the rule to be followed is that reusing should among vma of same process, and vma should not gone through fork). So, both issues should cause unnecessary rmap walking and have unexpected complexity. These two issues would not be directly visible, I used debugging code to check the anon_vma pointers of parent and child when inspecting the suspicious implementation of issue #2, then find the problem. This patch (of 3): In dup_mmap(), anon_vma_prepare() is called for vma has VM_WIPEONFORK, and parameter 'tmp' (i.e., the new vma of child) has same ->vm_next and ->vm_prev as its parent vma. That allows anon_vma used by parent been mistakenly shared by child (find_mergeable_anon_vma() will do this reuse work). Besides this issue, call anon_vma_prepare() should be avoided because we don't copy page for this vma. Preparing anon_vma will be handled during fault. Fixes: d2cd9ede ("mm,fork: introduce MADV_WIPEONFORK") Signed-off-by:
-
Chris Down authored
The root of the hierarchy cannot have high set, so we will never reclaim based on it. This makes that clearer and avoids another entry. Signed-off-by:
Chris Down <chris@chrisdown.name> Signed-off-by:
-
- 06 Apr, 2020 5 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull more ACPI updates from Rafael Wysocki: "Additional ACPI updates. These update the ACPICA code in the kernel to the 20200326 upstream revision, fix an ACPI-related CPU hotplug deadlock on x86, update Intel Tiger Lake device IDs in some places, add a new ACPI backlight blacklist entry, update the "acpi_backlight" kernel command line switch documentation and clean up a CPPC library routine. Specifics: - Update the ACPICA code in the kernel to upstream revision 20200326 including: * Fix for a typo in a comment field (Bob Moore) * acpiExec namespace init file fixes (Bob Moore) * Addition of NHLT to the known tables list (Cezary Rojewski) * Conversion of PlatformCommChannel ASL keyword to PCC (Erik Kaneda) * acpiexec cleanup (Erik Kaneda) * WSMT-related typo fix (Erik Kaneda) * sprintf() utility function fix (John Levon) * IVRS IVHD type 11h parsing implementation (Michał Żygowski) * IVRS IVHD type 10h reserved field name fix (Michał Żygowski) - Fix ACPI-related CPU hotplug deadlock on x86 (Qian Cai) - Fix Intel Tiger Lake ACPI device IDs in several places (Gayatri Kammela) - Add ACPI backlight blacklist entry for Acer Aspire 5783z (Hans de Goede) - Fix documentation of the "acpi_backlight" kernel command line switch (Randy Dunlap) - Clean up the acpi_get_psd_map() CPPC library routine (Liguang Zhang)" * tag 'acpi-5.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: x86: ACPI: fix CPU hotplug deadlock thermal: int340x_thermal: fix: Update Tiger Lake ACPI device IDs platform/x86: intel-hid: fix: Update Tiger Lake ACPI device ID ACPI: Update Tiger Lake ACPI device IDs ACPI: video: Use native backlight on Acer Aspire 5783z ACPI: video: Docs update for "acpi_backlight" kernel parameter options ACPICA: Update version 20200326 ACPICA: Fixes for acpiExec namespace init file ACPICA: Add NHLT table signature ACPICA: WSMT: Fix typo, no functional change ACPICA: utilities: fix sprintf() ACPICA: acpiexec: remove redeclaration of acpi_gbl_db_opt_no_region_support ACPICA: Change PlatformCommChannel ASL keyword to PCC ACPICA: Fix IVRS IVHD type 10h reserved field name ACPICA: Implement IVRS IVHD type 11h parsing ACPICA: Fix a typo in a comment field ACPI: CPPC: clean up acpi_get_psd_map() -
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull more power management updates from Rafael Wysocki: "Additional power management updates. These fix a corner-case suspend-to-idle wakeup issue on systems where the ACPI SCI is shared with another wakeup source, add a kernel command line option to set pm_debug_messages via the kernel command line, add a document desctibing system-wide suspend and resume code flows, modify cpufreq Kconfig to choose schedutil as the preferred governor by default in a couple of cases and do some assorted cleanups. Specifics: - Fix corner-case suspend-to-idle wakeup issue on systems where the ACPI SCI is shared with another wakeup source (Hans de Goede). - Add document describing system-wide suspend and resume code flows to the admin guide (Rafael Wysocki). - Add kernel command line option to set pm_debug_messages (Chen Yu). - Choose schedutil as the preferred scaling governor by default on ARM big.LITTLE systems and on x86 systems using the intel_pstate driver in the passive mode (Linus Walleij, Rafael Wysocki). - Drop racy and redundant checks from the PM core's device_prepare() routine (Rafael Wysocki). - Make resume from hibernation take the hibernation_restore() return value into account (Dexuan Cui)" * tag 'pm-5.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: platform/x86: intel_int0002_vgpio: Use acpi_register_wakeup_handler() ACPI: PM: Add acpi_[un]register_wakeup_handler() Documentation: PM: sleep: Document system-wide suspend code flows cpufreq: Select schedutil when using big.LITTLE PM: sleep: Add pm_debug_messages kernel command line option PM: sleep: core: Drop racy and redundant checks from device_prepare() PM: hibernate: Propagate the return value of hibernation_restore() cpufreq: intel_pstate: Select schedutil as the default governor -
git://github.com/c-sky/csky-linuxLinus Torvalds authored
Pull csky updates from Guo Ren: - Add kproobes/uprobes support - Add lockdep, rseq, gcov support - Fixup init_fpu - Fixup ftrace_modify deadlock - Fixup speculative execution on IO area * tag 'csky-for-linus-5.7-rc1' of git://github.com/c-sky/csky-linux: csky: Fixup cpu speculative execution to IO area csky: Add uprobes support csky: Add kprobes supported csky: Enable LOCKDEP_SUPPORT csky: Enable the gcov function csky: Fixup get wrong psr value from phyical reg csky/ftrace: Fixup ftrace_modify_code deadlock without CPU_HAS_ICACHE_INS csky: Implement ftrace with regs csky: Add support for restartable sequence csky: Implement ptrace regs and stack API csky: Fixup init_fpu compile warning with __init
-
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fsLinus Torvalds authored
Pull fsnotify updates from Jan Kara: "This implements the fanotify FAN_DIR_MODIFY event. This event reports the name in a directory under which a change happened and together with the directory filehandle and fstatat() allows reliable and efficient implementation of directory synchronization" * tag 'fsnotify_for_v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs: fanotify: Fix the checks in fanotify_fsid_equal fanotify: report name info for FAN_DIR_MODIFY event fanotify: record name info for FAN_DIR_MODIFY event fanotify: Drop fanotify_event_has_fid() fanotify: prepare to report both parent and child fid's fanotify: send FAN_DIR_MODIFY event flavor with dir inode and name fanotify: divorce fanotify_path_event and fanotify_fid_event fanotify: Store fanotify handles differently fanotify: Simplify create_fd() fanotify: fix merging marks masks with FAN_ONDIR fanotify: merge duplicate events on parent and child fsnotify: replace inode pointer with an object id fsnotify: simplify arguments passing to fsnotify_parent() fsnotify: use helpers to access data by data_type fsnotify: funnel all dirent events through fsnotify_name() fsnotify: factor helpers fsnotify_dentry() and fsnotify_file() fsnotify: tidy up FS_ and FAN_ constants
-
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fsLinus Torvalds authored
Pull ext2/udf updates from Jan Kara: "Cleanups and fixes for ext2 and one cleanup for udf" * tag 'for_v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs: ext2: fix empty body warnings when -Wextra is used ext2: fix debug reference to ext2_xattr_cache udf: udf_sb.h: Replace zero-length array with flexible-array member ext2: xattr.h: Replace zero-length array with flexible-array member ext2: Silence lockdep warning about reclaim under xattr_sem
-
