- 17 Aug, 2015 36 commits
-
-
Greg Kroah-Hartman authored
-
Michal Hocko authored
commit ecf5fc6e upstream. Nikolay has reported a hang when a memcg reclaim got stuck with the following backtrace: PID: 18308 TASK: ffff883d7c9b0a30 CPU: 1 COMMAND: "rsync" #0 __schedule at ffffffff815ab152 #1 schedule at ffffffff815ab76e #2 schedule_timeout at ffffffff815ae5e5 #3 io_schedule_timeout at ffffffff815aad6a #4 bit_wait_io at ffffffff815abfc6 #5 __wait_on_bit at ffffffff815abda5 #6 wait_on_page_bit at ffffffff8111fd4f #7 shrink_page_list at ffffffff81135445 #8 shrink_inactive_list at ffffffff81135845 #9 shrink_lruvec at ffffffff81135ead #10 shrink_zone at ffffffff811360c3 #11 shrink_zones at ffffffff81136eff #12 do_try_to_free_pages at ffffffff8113712f #13 try_to_free_mem_cgroup_pages at ffffffff811372be #14 try_charge at ffffffff81189423 #15 mem_cgroup_try_charge at ffffffff8118c6f5 #16 __add_to_page_cache_locked at ffffffff8112137d #17 add_to_page_cache_lru at ffffffff81121618 #18 pagecache_get_page at ffffffff8112170b #19 grow_dev_page at ffffffff811c8297 #20 __getblk_slow at ffffffff811c91d6 #21 __getblk_gfp at ffffffff811c92c1 #22 ext4_ext_grow_indepth at ffffffff8124565c #23 ext4_ext_create_new_leaf at ffffffff81246ca8 #24 ext4_ext_insert_extent at ffffffff81246f09 #25 ext4_ext_map_blocks at ffffffff8124a848 #26 ext4_map_blocks at ffffffff8121a5b7 #27 mpage_map_one_extent at ffffffff8121b1fa #28 mpage_map_and_submit_extent at ffffffff8121f07b #29 ext4_writepages at ffffffff8121f6d5 #30 do_writepages at ffffffff8112c490 #31 __filemap_fdatawrite_range at ffffffff81120199 #32 filemap_flush at ffffffff8112041c #33 ext4_alloc_da_blocks at ffffffff81219da1 #34 ext4_rename at ffffffff81229b91 #35 ext4_rename2 at ffffffff81229e32 #36 vfs_rename at ffffffff811a08a5 #37 SYSC_renameat2 at ffffffff811a3ffc #38 sys_renameat2 at ffffffff811a408e #39 sys_rename at ffffffff8119e51e #40 system_call_fastpath at ffffffff815afa89 Dave Chinner has properly pointed out that this is a deadlock in the reclaim code because ext4 doesn't submit pages which are marked by PG_writeback right away. The heuristic was introduced by commit e62e384e ("memcg: prevent OOM with too many dirty pages") and it was applied only when may_enter_fs was specified. The code has been changed by c3b94f44 ("memcg: further prevent OOM with too many dirty pages") which has removed the __GFP_FS restriction with a reasoning that we do not get into the fs code. But this is not sufficient apparently because the fs doesn't necessarily submit pages marked PG_writeback for IO right away. ext4_bio_write_page calls io_submit_add_bh but that doesn't necessarily submit the bio. Instead it tries to map more pages into the bio and mpage_map_one_extent might trigger memcg charge which might end up waiting on a page which is marked PG_writeback but hasn't been submitted yet so we would end up waiting for something that never finishes. Fix this issue by replacing __GFP_IO by may_enter_fs check (for case 2) before we go to wait on the writeback. The page fault path, which is the only path that triggers memcg oom killer since 3.12, shouldn't require GFP_NOFS and so we shouldn't reintroduce the premature OOM killer issue which was originally addressed by the heuristic. As per David Chinner the xfs is doing similar thing since 2.6.15 already so ext4 is not the only affected filesystem. Moreover he notes: : For example: IO completion might require unwritten extent conversion : which executes filesystem transactions and GFP_NOFS allocations. The : writeback flag on the pages can not be cleared until unwritten : extent conversion completes. Hence memory reclaim cannot wait on : page writeback to complete in GFP_NOFS context because it is not : safe to do so, memcg reclaim or otherwise. [tytso@mit.edu: corrected the control flow] Fixes: c3b94f44 ("memcg: further prevent OOM with too many dirty pages") Reported-by:
Nikolay Borisov <kernel@kyup.com> Signed-off-by:
Michal Hocko <mhocko@suse.cz> Signed-off-by:
Hugh Dickins <hughd@google.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
NeilBrown authored
commit b97e9257 upstream Use separate bitmaps for each nodes in the cluster bitmap_read_sb() validates the bitmap superblock that it reads in. If it finds an inconsistency like a bad magic number or out-of-range version number, it prints an error and returns, but it incorrectly returns zero, so the array is still assembled with the (invalid) bitmap. This means it could try to use a bitmap with a new version number which it therefore does not understand. This bug was introduced in 3.5 and fix as part of a larger patch in 4.1. So the patch is suitable for any -stable kernel in that range. Fixes: 27581e5a ("md/bitmap: centralise allocation of bitmap file pages.") Signed-off-by:
NeilBrown <neilb@suse.com> Reported-by:
GuoQing Jiang <gqjiang@suse.com>
-
Paolo Bonzini authored
commit ce40cd3f upstream. Malicious (or egregiously buggy) userspace can trigger it, but it should never happen in normal operation. Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Wang Kai <morgan.wang@huawei.com> Signed-off-by:
-
Amanieu d'Antras authored
commit 3c00cb5e upstream. This function can leak kernel stack data when the user siginfo_t has a positive si_code value. The top 16 bits of si_code descibe which fields in the siginfo_t union are active, but they are treated inconsistently between copy_siginfo_from_user32, copy_siginfo_to_user32 and copy_siginfo_to_user. copy_siginfo_from_user32 is called from rt_sigqueueinfo and rt_tgsigqueueinfo in which the user has full control overthe top 16 bits of si_code. This fixes the following information leaks: x86: 8 bytes leaked when sending a signal from a 32-bit process to itself. This leak grows to 16 bytes if the process uses x32. (si_code = __SI_CHLD) x86: 100 bytes leaked when sending a signal from a 32-bit process to a 64-bit process. (si_code = -1) sparc: 4 bytes leaked when sending a signal from a 32-bit process to a 64-bit process. (si_code = any) parsic and s390 have similar bugs, but they are not vulnerable because rt_[tg]sigqueueinfo have checks that prevent sending a positive si_code to a different process. These bugs are also fixed for consistency. Signed-off-by:
Amanieu d'Antras <amanieu@gmail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Amanieu d'Antras authored
commit 26135022 upstream. This function may copy the si_addr_lsb, si_lower and si_upper fields to user mode when they haven't been initialized, which can leak kernel stack data to user mode. Just checking the value of si_code is insufficient because the same si_code value is shared between multiple signals. This is solved by checking the value of si_signo in addition to si_code. Signed-off-by:
-
Amanieu d'Antras authored
commit 3ead7c52 upstream. This function may copy the si_addr_lsb field to user mode when it hasn't been initialized, which can leak kernel stack data to user mode. Just checking the value of si_code is insufficient because the same si_code value is shared between multiple signals. This is solved by checking the value of si_signo in addition to si_code. Signed-off-by:
-
Fabio Estevam authored
commit 7cb3be0a upstream. Commit 2ba85e7a (ARM: Fix FIQ code on VIVT CPUs) causes the following build warning: arch/arm/kernel/fiq.c:92:3: warning: passing argument 1 of 'cpu_cache.coherent_kern_range' makes integer from pointer without a cast [enabled by default] Cast it as '(unsigned long)base' to avoid the warning. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Cc: Martin Kaiser <lists@kaiser.cx> Signed-off-by:
-
Russell King authored
commit 2ba85e7a upstream. Aaro Koskinen reports the following oops: Installing fiq handler from c001b110, length 0x164 Unable to handle kernel paging request at virtual address ffff1224 pgd = c0004000 [ffff1224] *pgd=00000000, *pte=11fff0cb, *ppte=11fff00a ... [<c0013154>] (set_fiq_handler+0x0/0x6c) from [<c0365d38>] (ams_delta_init_fiq+0xa8/0x160) r6:00000164 r5:c001b110 r4:00000000 r3:fefecb4c [<c0365c90>] (ams_delta_init_fiq+0x0/0x160) from [<c0365b14>] (ams_delta_init+0xd4/0x114) r6:00000000 r5:fffece10 r4:c037a9e0 [<c0365a40>] (ams_delta_init+0x0/0x114) from [<c03613b4>] (customize_machine+0x24/0x30) This is because the vectors page is now write-protected, and to change code in there we must write to its original alias. Make that change, and adjust the cache flushing such that the code will become visible to the instruction stream on VIVT CPUs. Reported-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Tested-by:
-
Russell King authored
commit 1b16c4bc upstream. Fix yet another build failure caused by a weird set of configuration settings: LD init/built-in.o arch/arm/kernel/built-in.o: In function `__dabt_usr': /home/tom3q/kernel/arch/arm/kernel/entry-armv.S:377: undefined reference to `kuser_cmpxchg64_fixup' arch/arm/kernel/built-in.o: In function `__irq_usr': /home/tom3q/kernel/arch/arm/kernel/entry-armv.S:387: undefined reference to `kuser_cmpxchg64_fixup' caused by: CONFIG_KUSER_HELPERS=n CONFIG_CPU_32v6K=n CONFIG_NEEDS_SYSCALL_FOR_CMPXCHG=n Reported-by:
Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by:
-
Al Viro authored
commit 451a2886 upstream. unfortunately, allowing an arbitrary 16bit value means a possibility of overflow in the calculation of total number of pages in bio_map_user_iov() - we rely on there being no more than PAGE_SIZE members of sum in the first loop there. If that sum wraps around, we end up allocating too small array of pointers to pages and it's easy to overflow it in the second loop. X-Coverup: TINC (and there's no lumber cartel either) Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> [bwh: s/MAX_UIOVEC/UIO_MAXIOV/. This was fixed upstream by commit fdc81f45 ("sg_start_req(): use import_iovec()"), but we don't have that function.] Signed-off-by:
-
NeilBrown authored
commit 423f04d6 upstream. raid1_end_read_request() assumes that the In_sync bits are consistent with the ->degaded count. raid1_spare_active updates the In_sync bit before the ->degraded count and so exposes an inconsistency, as does error() So extend the spinlock in raid1_spare_active() and error() to hide those inconsistencies. This should probably be part of Commit: 34cab6f4 ("md/raid1: fix test for 'was read error from last working device'.") as it addresses the same issue. It fixes the same bug and should go to -stable for same reasons. Fixes: 76073054 ("md/raid1: clean up read_balance.") Signed-off-by:
-
Joseph Qi authored
commit 209f7512 upstream. The "BUG_ON(list_empty(&osb->blocked_lock_list))" in ocfs2_downconvert_thread_do_work can be triggered in the following case: ocfs2dc has firstly saved osb->blocked_lock_count to local varibale processed, and then processes the dentry lockres. During the dentry put, it calls iput and then deletes rw, inode and open lockres from blocked list in ocfs2_mark_lockres_freeing. And this causes the variable `processed' to not reflect the number of blocked lockres to be processed, which triggers the BUG. Signed-off-by:
Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by:
-
Marcus Gelderie authored
commit de54b9ac upstream. A while back, the message queue implementation in the kernel was improved to use btrees to speed up retrieval of messages, in commit d6629859 ("ipc/mqueue: improve performance of send/recv"). That patch introducing the improved kernel handling of message queues (using btrees) has, as a by-product, changed the meaning of the QSIZE field in the pseudo-file created for the queue. Before, this field reflected the size of the user-data in the queue. Since, it also takes kernel data structures into account. For example, if 13 bytes of user data are in the queue, on my machine the file reports a size of 61 bytes. There was some discussion on this topic before (for example https://lkml.org/lkml/2014/10/1/115). Commenting on a th lkml, Michael Kerrisk gave the following background (https://lkml.org/lkml/2015/6/16/74): The pseudofiles in the mqueue filesystem (usually mounted at /dev/mqueue) expose fields with metadata describing a message queue. One of these fields, QSIZE, as originally implemented, showed the total number of bytes of user data in all messages in the message queue, and this feature was documented from the beginning in the mq_overview(7) page. In 3.5, some other (useful) work happened to break the user-space API in a couple of places, including the value exposed via QSIZE, which now includes a measure of kernel overhead bytes for the queue, a figure that renders QSIZE useless for its original purpose, since there's no way to deduce the number of overhead bytes consumed by the implementation. (The other user-space breakage was subsequently fixed.) This patch removes the accounting of kernel data structures in the queue. Reporting the size of these data-structures in the QSIZE field was a breaking change (see Michael's comment above). Without the QSIZE field reporting the total size of user-data in the queue, there is no way to deduce this number. It should be noted that the resource limit RLIMIT_MSGQUEUE is counted against the worst-case size of the queue (in both the old and the new implementation). Therefore, the kernel overhead accounting in QSIZE is not necessary to help the user understand the limitations RLIMIT imposes on the processes. Signed-off-by:
Marcus Gelderie <redmnic@gmail.com> Acked-by:
Doug Ledford <dledford@redhat.com> Acked-by:
Michael Kerrisk <mtk.manpages@gmail.com> Acked-by:
Davidlohr Bueso <dbueso@suse.de> Cc: David Howells <dhowells@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: John Duffy <jb_duffy@btinternet.com> Cc: Arto Bendiken <arto@bendiken.net> Cc: Manfred Spraul <manfred@colorfullife.com> Signed-off-by:
-
Dan Carpenter authored
commit 44008f08 upstream. Smatch complains that we have nested checks for "spdif_present". It turns out the current behavior isn't correct, we should remove the first check and keep the second. Fixes: 1077a024 ('ALSA: hda - Use generic parser for Cirrus codec driver') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Nicholas Bellinger authored
commit e5419865 upstream. This patch fixes a regression introduced with the following commit in v4.0-rc1 code, where a iscsit_start_kthreads() failure triggers a NULL pointer dereference OOPs: commit 88dcd2da Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Feb 26 22:19:15 2015 -0800 iscsi-target: Convert iscsi_thread_set usage to kthread.h To address this bug, move iscsit_start_kthreads() immediately preceeding the transmit of last login response, before signaling a successful transition into full-feature-phase within existing iscsi_target_do_tx_login_io() logic. This ensures that no target-side resource allocation failures can occur after the final login response has been successfully sent. Also, it adds a iscsi_conn->rx_login_comp to allow the RX thread to sleep to prevent other socket related failures until the final iscsi_post_login_handler() call is able to complete. Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
Nicholas Bellinger <nab@daterainc.com> Signed-off-by:
-
Ilya Dryomov authored
commit 2761713d upstream. For write/discard obj_requests that involved a copyup method call, the opcode of the first op is CEPH_OSD_OP_CALL and the ->callback is rbd_img_obj_copyup_callback(). The latter frees copyup pages, sets ->xferred and delegates to rbd_img_obj_callback(), the "normal" image object callback, for reporting to block layer and putting refs. rbd_osd_req_callback() however treats CEPH_OSD_OP_CALL as a trivial op, which means obj_request is marked done in rbd_osd_trivial_callback(), *before* ->callback is invoked and rbd_img_obj_copyup_callback() has a chance to run. Marking obj_request done essentially means giving rbd_img_obj_callback() a license to end it at any moment, so if another obj_request from the same img_request is being completed concurrently, rbd_img_obj_end_request() may very well be called on such prematurally marked done request: <obj_request-1/2 reply> handle_reply() rbd_osd_req_callback() rbd_osd_trivial_callback() rbd_obj_request_complete() rbd_img_obj_copyup_callback() rbd_img_obj_callback() <obj_request-2/2 reply> handle_reply() rbd_osd_req_callback() rbd_osd_trivial_callback() for_each_obj_request(obj_request->img_request) { rbd_img_obj_end_request(obj_request-1/2) rbd_img_obj_end_request(obj_request-2/2) <-- } Calling rbd_img_obj_end_request() on such a request leads to trouble, in particular because its ->xfferred is 0. We report 0 to the block layer with blk_update_request(), get back 1 for "this request has more data in flight" and then trip on rbd_assert(more ^ (which == img_request->obj_request_count)); with rhs (which == ...) being 1 because rbd_img_obj_end_request() has been called for both requests and lhs (more) being 1 because we haven't got a chance to set ->xfferred in rbd_img_obj_copyup_callback() yet. To fix this, leverage that rbd wants to call class methods in only two cases: one is a generic method call wrapper (obj_request is standalone) and the other is a copyup (obj_request is part of an img_request). So make a dedicated handler for CEPH_OSD_OP_CALL and directly invoke rbd_img_obj_copyup_callback() from it if obj_request is part of an img_request, similar to how CEPH_OSD_OP_READ handler invokes rbd_img_obj_request_read_callback(). Since rbd_img_obj_copyup_callback() is now being called from the OSD request callback (only), it is renamed to rbd_osd_copyup_callback(). Cc: Alex Elder <elder@linaro.org> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Herbert Xu authored
commit f898c522 upstream. This patch removes a bogus BUG_ON in the ablkcipher path that triggers when the destination buffer is different from the source buffer and is scattered. Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Marek Marczykowski-Górecki authored
commit 30b03d05 upstream. While gntdev_release() is called the MMU notifier is still registered and can traverse priv->maps list even if no pages are mapped (which is the case -- gntdev_release() is called after all). But gntdev_release() will clear that list, so make sure that only one of those things happens at the same time. Signed-off-by:
Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Andy Lutomirski authored
commit aa1acff3 upstream. The update_va_mapping hypercall can fail if the VA isn't present in the guest's page tables. Under certain loads, this can result in an OOPS when the target address is in unpopulated vmap space. While we're at it, add comments to help explain what's going on. This isn't a great long-term fix. This code should probably be changed to use something like set_memory_ro. Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Andrew Cooper <andrew.cooper3@citrix.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Vrabel <dvrabel@cantab.net> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jan Beulich <jbeulich@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: security@kernel.org <security@kernel.org> Cc: xen-devel <xen-devel@lists.xen.org> Link: http://lkml.kernel.org/r/0b0e55b995cda11e7829f140b833ef932fcabe3a.1438291540.git.luto@kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 44922150 ] If we have a series of events from userpsace, with %fprs=FPRS_FEF, like follows: ETRAP ETRAP VIS_ENTRY(fprs=0x4) VIS_EXIT RTRAP (kernel FPU restore with fpu_saved=0x4) RTRAP We will not restore the user registers that were clobbered by the FPU using kernel code in the inner-most trap. Traps allocate FPU save slots in the thread struct, and FPU using sequences save the "dirty" FPU registers only. This works at the initial trap level because all of the registers get recorded into the top-level FPU save area, and we'll return to userspace with the FPU disabled so that any FPU use by the user will take an FPU disabled trap wherein we'll load the registers back up properly. But this is not how trap returns from kernel to kernel operate. The simplest fix for this bug is to always save all FPU register state for anything other than the top-most FPU save area. Getting rid of the optimized inner-slot FPU saving code ends up making VISEntryHalf degenerate into plain VISEntry. Longer term we need to do something smarter to reinstate the partial save optimizations. Perhaps the fundament error is having trap entry and exit allocate FPU save slots and restore register state. Instead, the VISEntry et al. calls should be doing that work. This bug is about two decades old. Reported-by:
James Y Knight <jyknight@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
David S. Miller authored
[ Upstream commit f4da3628 ] The AES loops in arch/sparc/crypto/aes_glue.c use a scheme where the key material is preloaded into the FPU registers, and then we loop over and over doing the crypt operation, reusing those pre-cooked key registers. There are intervening blkcipher*() calls between the crypt operation calls. And those might perform memcpy() and thus also try to use the FPU. The sparc64 kernel FPU usage mechanism is designed to allow such recursive uses, but with a catch. There has to be a trap between the two FPU using threads of control. The mechanism works by, when the FPU is already in use by the kernel, allocating a slot for FPU saving at trap time. Then if, within the trap handler, we try to use the FPU registers, the pre-trap FPU register state is saved into the slot. Then at trap return time we notice this and restore the pre-trap FPU state. Over the long term there are various more involved ways we can make this work, but for a quick fix let's take advantage of the fact that the situation where this happens is very limited. All sparc64 chips that support the crypto instructiosn also are using the Niagara4 memcpy routine, and that routine only uses the FPU for large copies where we can't get the source aligned properly to a multiple of 8 bytes. We look to see if the FPU is already in use in this context, and if so we use the non-large copy path which only uses integer registers. Furthermore, we also limit this special logic to when we are doing kernel copy, rather than a user copy. Signed-off-by:
-
Peter Zijlstra authored
commit 1b45adcd upstream. Josh reported that his QEMU is a bad hardware emulator and trips a WARN in the AMD PMU init code. He requested the WARN be turned into a pr_err() or similar. While there, rework the code a little. Reported-by:
Josh Boyer <jwboyer@redhat.com> Acked-by:
Robert Richter <rric@kernel.org> Acked-by:
Jacob Shin <jacob.shin@amd.com> Cc: Stephane Eranian <eranian@google.com> Signed-off-by:
Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20130521110537.GG26912@twins.programming.kicks-ass.netSigned-off-by:
-
Guenter Roeck authored
commit 8a8320c2 upstream. Fix: sm501 sm501: SM501 At b3e00000: Version 050100a0, 8 Mb, IRQ 100 Attribute dbg_regs: write permission without 'store' ------------[ cut here ]------------ WARNING: at drivers/base/core.c:620 dbg_regs does not have a write function and must therefore be marked as read-only. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Xie XiuQi authored
commit e21404dc upstream. Loading ipmi_si module while bmc is disconnected, we found the timeout is longer than 5 secs. Actually it takes about 3 mins and 20 secs.(HZ=250) error message as below: Dec 12 19:08:59 linux kernel: IPMI BT: timeout in RD_WAIT [ ] 1 retries left Dec 12 19:08:59 linux kernel: BT: write 4 bytes seq=0x01 03 18 00 01 [...] Dec 12 19:12:19 linux kernel: IPMI BT: timeout in RD_WAIT [ ] Dec 12 19:12:19 linux kernel: failed 2 retries, sending error response Dec 12 19:12:19 linux kernel: IPMI: BT reset (takes 5 secs) Dec 12 19:12:19 linux kernel: IPMI BT: flag reset [ ] Function wait_for_msg_done() use schedule_timeout_uninterruptible(1) to sleep 1 tick, so we should subtract jiffies_to_usecs(1) instead of 100 usecs from timeout. Reported-by:
Hu Shiyuan <hushiyuan@huawei.com> Signed-off-by:
Xie XiuQi <xiexiuqi@huawei.com> Signed-off-by:
Corey Minyard <cminyard@mvista.com> Signed-off-by:
-
Benjamin Randazzo authored
commit b6878d9e upstream. In drivers/md/md.c get_bitmap_file() uses kmalloc() for creating a mdu_bitmap_file_t called "file". 5769 file = kmalloc(sizeof(*file), GFP_NOIO); 5770 if (!file) 5771 return -ENOMEM; This structure is copied to user space at the end of the function. 5786 if (err == 0 && 5787 copy_to_user(arg, file, sizeof(*file))) 5788 err = -EFAULT But if bitmap is disabled only the first byte of "file" is initialized with zero, so it's possible to read some bytes (up to 4095) of kernel space memory from user space. This is an information leak. 5775 /* bitmap disabled, zero the first byte and copy out */ 5776 if (!mddev->bitmap_info.file) 5777 file->pathname[0] = '\0'; Signed-off-by:
Benjamin Randazzo <benjamin@randazzo.fr> Signed-off-by:
-
Dirk Behme authored
commit 74472233 upstream. Add support for the Sierra Wireless AR8550 device with USB descriptor 0x1199, 0x68AB. It is common with MC879x modules 1199:683c/683d which also are composite devices with 7 interfaces (0..6) and also MDM62xx based as the AR8550. The major difference are only the interface attributes 02/02/01 on interfaces 3 and 4 on the AR8550. They are vendor specific ff/ff/ff on MC879x modules. lsusb reports: Bus 001 Device 004: ID 1199:68ab Sierra Wireless, Inc. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x1199 Sierra Wireless, Inc. idProduct 0x68ab bcdDevice 0.06 iManufacturer 3 Sierra Wireless, Incorporated iProduct 2 AR8550 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 198 bNumInterfaces 7 bConfigurationValue 1 iConfiguration 1 Sierra Configuration bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 3 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x84 EP 4 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 4 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x87 EP 7 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 5 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x88 EP 8 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x89 EP 9 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 6 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x8a EP 10 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x8b EP 11 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x07 EP 7 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Signed-off-by:
Dirk Behme <dirk.behme@de.bosch.com> Cc: Lars Melin <larsm17@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Mathias Nyman authored
commit 7895086a upstream. We need to check that a TRB is part of the current segment before calculating its DMA address. Previously a ring segment didn't use a full memory page, and every new ring segment got a new memory page, so the off by one error in checking the upper bound was never seen. Now that we use a full memory page, 256 TRBs (4096 bytes), the off by one didn't catch the case when a TRB was the first element of the next segment. This is triggered if the virtual memory pages for a ring segment are next to each in increasing order where the ring buffer wraps around and causes errors like: [ 106.398223] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 0 comp_code 1 [ 106.398230] xhci_hcd 0000:00:14.0: Looking for event-dma fffd3000 trb-start fffd4fd0 trb-end fffd5000 seg-start fffd4000 seg-end fffd4ff0 The trb-end address is one outside the end-seg address. Tested-by:
Arkadiusz Miśkiewicz <arekm@maven.pl> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Brian King authored
commit 3f1c0581 upstream. Fixes another signed / unsigned array indexing bug in the ipr driver. Currently, when hrrq_index wraps, it becomes a negative number. We do the modulo, but still have a negative number, so we end up indexing backwards in the array. Given where the hrrq array is located in memory, we probably won't actually reference memory we don't own, but nonetheless ipr is still looking at data within struct ipr_ioa_cfg and interpreting it as struct ipr_hrr_queue data, so bad things could certainly happen. Each ipr adapter has anywhere from 1 to 16 HRRQs. By default, we use 2 on new adapters. Let's take an example: Assume ioa_cfg->hrrq_index=0x7fffffffe and ioa_cfg->hrrq_num=4: The atomic_add_return will then return -1. We mod this with 3 and get -2, add one and get -1 for an array index. On adapters which support more than a single HRRQ, we dedicate HRRQ to adapter initialization and error interrupts so that we can optimize the other queues for fast path I/O. So all normal I/O uses HRRQ 1-15. So we want to spread the I/O requests across those HRRQs. With the default module parameter settings, this bug won't hit, only when someone sets the ipr.number_of_msix parameter to a value larger than 3 is when bad things start to happen. Tested-by:
Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by:
Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Reviewed-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Brian King authored
commit bb7c5433 upstream. When ipr's internal driver trace was changed to an atomic, a signed/unsigned bug slipped in which results in us indexing backwards in our memory buffer writing on memory that does not belong to us. This patch fixes this by removing the modulo and instead just mask off the low bits. Tested-by:
-
Brian King authored
commit 36b8e180 upstream. Make sure we have the host lock held when calling scsi_report_bus_reset. Fixes a crash seen as the __devices list in the scsi host was changing as we were iterating through it. Reviewed-by:
-
Alex Deucher authored
commit 0a90a0cf upstream. Fixes a broken hsync start value uncovered by: abc0b144 (drm: Perform basic sanity checks on probed modes) The driver handled the bad hsync start elsewhere, but the above commit prevented it from getting added. bug: https://bugs.freedesktop.org/show_bug.cgi?id=91401Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Jan Kara authored
commit 8f2f3eb5 upstream. fsnotify_clear_marks_by_group_flags() can race with fsnotify_destroy_marks() so that when fsnotify_destroy_mark_locked() drops mark_mutex, a mark from the list iterated by fsnotify_clear_marks_by_group_flags() can be freed and thus the next entry pointer we have cached may become stale and we dereference free memory. Fix the problem by first moving marks to free to a special private list and then always free the first entry in the special list. This method is safe even when entries from the list can disappear once we drop the lock. Signed-off-by:
Jan Kara <jack@suse.com> Reported-by:
Ashish Sangwan <a.sangwan@samsung.com> Reviewed-by:
-
David Daney authored
commit 46011e6e upstream. On MIPS the GLOBAL bit of the PTE must have the same value in any aligned pair of PTEs. These pairs of PTEs are referred to as "buddies". In a SMP system is is possible for two CPUs to be calling set_pte() on adjacent PTEs at the same time. There is a race between setting the PTE and a different CPU setting the GLOBAL bit in its buddy PTE. This race can be observed when multiple CPUs are executing vmap()/vfree() at the same time. Make setting the buddy PTE's GLOBAL bit an atomic operation to close the race condition. The case of CONFIG_64BIT_PHYS_ADDR && CONFIG_CPU_MIPS32 is *not* handled. Signed-off-by:
David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/10835/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Felix Fietkau authored
commit 1d62d737 upstream. p->thread.user_cpus_allowed is zero-initialized and is only filled on the first sched_setaffinity call. To avoid adding overhead in the task initialization codepath, simply OR the returned mask in sched_getaffinity with p->cpus_allowed. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/10740/Signed-off-by:
-
Arnd Bergmann authored
commit dd94d355 upstream. Commit b713aa0b "ARM: fix asm/memory.h build error" broke some configurations on mach-realview with sparsemem enabled, which is missing a definition of PHYS_OFFSET: arch/arm/include/asm/memory.h:268:42: error: 'PHYS_OFFSET' undeclared (first use in this function) #define PHYS_PFN_OFFSET ((unsigned long)(PHYS_OFFSET >> PAGE_SHIFT)) arch/arm/include/asm/dma-mapping.h:104:9: note: in expansion of macro 'PHYS_PFN_OFFSET' return PHYS_PFN_OFFSET + dma_to_pfn(dev, *dev->dma_mask); An easy workaround is for realview to define PHYS_OFFSET itself, in the same way we define it for platforms that don't have a private __virt_to_phys function. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
- 10 Aug, 2015 4 commits
-
-
Greg Kroah-Hartman authored
-
Fupan Li authored
Commit 35d5134b ("x86/efi: Correct EFI boot stub use of code32_start") imported a bug, which will cause 32bit kernel boot failed using efi method. It should use the label's address instead of the value stored in the label to caculate the address of code32_start. Signed-off-by:
Fupan Li <fupan.li@windriver.com> Reviewed-by:
Matt Fleming <matt.fleming@intel.com>
-
Nicholas Bellinger authored
commit 007d038b upstream. This patch fixes a regression introduced with the following commit in v4.0-rc1 code, where an explicit iser-target logout would result in ->tx_thread_active being incorrectly cleared by the logout post handler, and subsequent TX kthread leak: commit 88dcd2da Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Feb 26 22:19:15 2015 -0800 iscsi-target: Convert iscsi_thread_set usage to kthread.h To address this bug, change iscsit_logout_post_handler_closesession() and iscsit_logout_post_handler_samecid() to only cmpxchg() on ->tx_thread_active for traditional iscsi/tcp connections. This is required because iscsi/tcp connections are invoking logout post handler logic directly from TX kthread context, while iser connections are invoking logout post handler logic from a seperate workqueue context. Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 417c20a9 upstream. This patch fixes a use-after-free bug in iscsit_release_sessions_for_tpg() where se_portal_group->session_lock was incorrectly released/re-acquired while walking the active se_portal_group->tpg_sess_list. The can result in a NULL pointer dereference when iscsit_close_session() shutdown happens in the normal path asynchronously to this code, causing a bogus dereference of an already freed list entry to occur. To address this bug, walk the session list checking for the same state as before, but move entries to a local list to avoid dropping the lock while walking the active list. As before, signal using iscsi_session->session_restatement=1 for those list entries to be released locally by iscsit_free_session() code. Reported-by:
Sunilkumar Nadumuttlu <sjn@datera.io> Cc: Sunilkumar Nadumuttlu <sjn@datera.io> Signed-off-by:
-
