GitLab

- vxge driver help text file.

- No change from previous submission.

- Changes in previous submissions -
  Removed the performance tuning section with instructions to disable
  time stamps and change sysctl settings - Reported by Dave Miller
  General clean up.
 - Removed tx/rx_pause, exec_mode, tx_steering_type, rx_steering_type, gro,
   intr_type, rx & tx max_indicate_pkts and exec_mode loadable parameters. The
   driver default settings work well in most if not all cases. Another patch
   to configure these parameters with ethtool will be released in the future -
   Reported by Stephen Hemminger.
- Incorporated following fixes based on comments from Ben Hutchings
        Removed references to earlier kernel versions.
        Removed sections that are similar for all drivers -
                Load/Unload
                Identifying the adapter/interface
                Boot time configuration
        Removed loadable parameter -
                NAPI - Napi is always enabled.
...

If we use a shared legacy IRQ then our interrupt handler may be called
as soon as it is registered even though IRQs are disabled on the NIC.
Now that the legacy interrupt handler also checks for event delivery,
it may decide to schedule polling in this case.  Ensure that the NAPI
context is valid but disabled at this point.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove pointless conditional before kfree().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let driver depend on HAS_IOMEM to avoid build breakage on s390:

  CC      drivers/net/ethoc.o
drivers/net/ethoc.c: In function 'ethoc_read':
drivers/net/ethoc.c:221: error: implicit declaration of function 'ioread32'
drivers/net/ethoc.c: In function 'ethoc_write':
drivers/net/ethoc.c:226: error: implicit declaration of function 'iowrite32'
drivers/net/ethoc.c: In function 'ethoc_rx':
drivers/net/ethoc.c:405: error: implicit declaration of function 'memcpy_fromio'
drivers/net/ethoc.c: In function 'ethoc_start_xmit':
drivers/net/ethoc.c:828: error: implicit declaration of function 'memcpy_toio'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added osi_load_firmware() instead of copying same thing twice
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>

Added predef variable in add_mcs() to support predefined mcs data
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a dependency with IPv6:

ERROR: "__ipv6_addr_type" [net/netfilter/xt_cluster.ko] undefined!

This patch adds a function that checks if the higher bits of the
address is 0xFF to identify a multicast address, instead of adding a
dependency due to __ipv6_addr_type(). I came up with this idea after
Patrick McHardy pointed possible problems with runtime module
dependencies.
Reported-by: Steven Noonan <steven@uplinklabs.net>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

We can't put 'mdio' until after we've used it in the
fsl_pq_mdio_bus_name() call.

Also fix error return values.
Signed-off-by: David S. Miller <davem@davemloft.net>

We can't put 'mdio' until after we've used it in the
fsl_pq_mdio_bus_name() call.
Signed-off-by: David S. Miller <davem@davemloft.net>

All users have been removed.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allows for the removal of byteswapping in some places and
the removal of HIPQUAD (replaced by %pI4).
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dcc_ip is treated as a host-endian value in the first printk,
but the second printk uses %pI4 which expects a be32.  This
will cause a mismatch between the debug statement and the
warning statement.

Treat as a be32 throughout and avoid some byteswapping during
some comparisions, and allow another user of HIPQUAD to bite the
dust.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/hamradio/dmascc.c:587: error: 'struct net_device' has no
member named 'set_mac_address'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When GRO/frag_list support was added to GSO, I made an error
which broke the support for segmenting linear GSO packets (GSO
packets are normally non-linear in the payload).

These days most of these packets are constructed by the tun
driver, which prefers to allocate linear memory if possible.
This is fixed in the latest kernel, but for 2.6.29 and earlier
it is still the norm.

Therefore this bug causes failures with GSO when used with tun
in 2.6.29.
Reported-by: James Huang <jamesclhuang@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing struct field to fix kernel-doc warning:

Warning(include/linux/skbuff.h:182): No description found for parameter 'flags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c-core: Some style cleanups
  i2c-piix4: Add support for the Broadcom HT1100 chipset
  i2c-piix4: Add support to SB800 SMBus changes
  i2c-pca-platform: Use defaults if no platform_data given
  i2c-algo-pca: Use timeout for checking the state machine
  i2c-algo-pca: Rework waiting for a free bus
  i2c-algo-pca: Add PCA9665 support
  i2c: Adapt debug macros for KERN_* constants
  i2c-davinci: Fix timeout handling
  i2c: Adapter timeout is in jiffies
  i2c: Set a default timeout value for all adapters
  i2c: Add missing KERN_* constants to printks
  i2c-algo-pcf: Handle timeout correctly
  i2c-algo-pcf: Style cleanups
  eeprom/at24: Remove EXPERIMENTAL
  i2c-nforce2: Add support for MCP67, MCP73, MCP78S and MCP79
  i2c: Clarify which clients are auto-removed
  i2c: Let checkpatch shout on users of the legacy model
  i2c: Document the different ways to instantiate i2c devices

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits)
  [ARM] 5435/1: fix compile warning in sanity_check_meminfo()
  [ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx
  [ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0
  [ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins
  imxfb: Fix TFT mode
  i.MX21/27: remove ifdef CONFIG_FB_IMX
  imxfb: add clock support
  mxc: add arch_reset() function
  clkdev: add possibility to get a clock based on the device name
  i.MX1: remove fb support from mach-imx
  [ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined
  Gemini: Add support for Teltonika RUT100
  Gemini: gpiolib based GPIO support v2
  MAINTAINERS: add myself as Gemini architecture maintainer
  ARM: Add Gemini architecture v3
  [ARM] OMAP: Fix compile for omap2_init_common_hw()
  MAINTAINERS: Add myself as Faraday ARM core variant maintainer
  ARM: Add support for FA526 v2
  [ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h
  [ARM] collie: fix two minor formatting nits
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/arjan/linux-2.6-async-for-30:
  fastboot: remove duplicate unpack_to_rootfs()
  ide/net: flip the order of SATA and network init
  async: remove the temporary (2.6.29) "async is off by default" code

Fix up conflicts in init/initramfs.c manually

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
  Blackfin arch: be less noisy when gets a gpio conflict after kernel has booted
  Blackfin arch: add RSI's definitions to bf514 and bf516
  Blackfin arch: add link-time asserts to make sure on-chip regions dont overflow
  Blackfin arch: sport spi needs 6 gpio pins
  Blackfin arch: add sport-spi related resource stuff to board file
  Blackfin arch: Blacklist Hibernate (PM_SUSPEND_MEM) on BF561 as well
  Blackfin arch: Privide BF537-STAMP platform data of ADP5520 Multifunction driver
  Blackfin arch: enable the platfrom PATA driver with CF Cards
  Blackfin arch: clean up sports header file
  Blackfin arch: convert BF5{18,27,48}_FAMILY to CONFIG_BF{51,52,54}x
  Blackfin arch: bf51x processors also have 8 timers
  Blackfin arch: add a check to make sure only Blackfin GPIOs may generate IRQs
  Blackfin arch: update default kernel configuration
  Blackfin arch: include linux headers that this one uses definitions from fro sport drivers

Merge branch 'percpu-cpumask-x86-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'percpu-cpumask-x86-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (682 commits)
  percpu: fix spurious alignment WARN in legacy SMP percpu allocator
  percpu: generalize embedding first chunk setup helper
  percpu: more flexibility for @dyn_size of pcpu_setup_first_chunk()
  percpu: make x86 addr <-> pcpu ptr conversion macros generic
  linker script: define __per_cpu_load on all SMP capable archs
  x86: UV: remove uv_flush_tlb_others() WARN_ON
  percpu: finer grained locking to break deadlock and allow atomic free
  percpu: move fully free chunk reclamation into a work
  percpu: move chunk area map extension out of area allocation
  percpu: replace pcpu_realloc() with pcpu_mem_alloc() and pcpu_mem_free()
  x86, percpu: setup reserved percpu area for x86_64
  percpu, module: implement reserved allocation and use it for module percpu variables
  percpu: add an indirection ptr for chunk page map access
  x86: make embedding percpu allocator return excessive free space
  percpu: use negative for auto for pcpu_setup_first_chunk() arguments
  percpu: improve first chunk initial area map handling
  percpu: cosmetic renames in pcpu_setup_first_chunk()
  percpu: clean up percpu constants
  x86: un-__init fill_pud/pmd/pte
  x86: remove vestigial fix_ioremap prototypes
  ...

Manually merge conflicts in arch/ia64/kernel/irq_ia64.c

Some lines over 80. 
The printk(KERN_ERR ... ) should be dev_err.
And some blankspace should be deleted.
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Signed-off-by: Jean Delvare <khlai@linux-fr.org>

Add support for the Broadcom HT1100 LD chipset (SMBus function.)
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Add support for the AMD SB800 Family series of products.
Major changes include the changes to addressing the SMBus registers at different
location from the locations in the previous compatible parts from AMD such as
SB400/SB600/SB700. For SB800, the main features and register definitions of
SMBus and other interfaces are still compatible with the previous products with
the only change being in how to access the internal registers for these blocks.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

We now timeout also if the state machine does not change within the
given time. For that, the driver-specific completion-functions are
extended to return true or false depending on the timeout. This then
gets checked in the algorithm.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Waiting for a free bus now accepts the timeout value in jiffies and does
proper checking using time_before.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Add support for the PCA9665 I2C controller.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the changes to the debug macros in the i2c subsystem
to meet this requirement. Also changing no-debug statements
to raw printks again.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>

Properly set the adapter timeout value in jiffies, and then use that
value in the driver, rather than a hard-coded constant.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Kevin Hilman <khilman@mvista.com>

i2c_adapter.timeout is in jiffies. Fix all drivers which thought
otherwise. It didn't really matter as long as the value was only used
inside the driver, but soon i2c-core will use it too so it must have
the proper unit.

Note: for the i2c-mpc driver, this fixes a bug in polling mode.
Timeout would trigger after 1 jiffy, which is most probably not what
the author wanted.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Clifford Wolf <clifford@clifford.at>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Mark A. Greer <mgreer@mvista.com>

Setting a default timeout value on a per-algo basis doesn't make any
sense. Move the default value setting to i2c-core. Individual adapter
drivers can specify a different (non-zero) value if they wish.

Also express the timeout value in a way which results in the same
duration regarless of the value of HZ.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>

According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing pieces here for the i2c subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>