- 12 Jan, 2014 14 commits
-
-
Simon Wunderlich authored
To show information per interface, add a debugfs hardif structure similar to the system in sysfs. Hard interface folders will be created in "$debugfs/batman-adv/". Files are not yet added. Signed-off-by:
Simon Wunderlich <simon@open-mesh.com> Signed-off-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
Antonio Quartulli <antonio@meshcoding.com>
-
Simon Wunderlich authored
With the new interface alternating, the first hop may send packets in a round robin fashion to it's neighbors because it has multiple valid routes built by the multi interface optimization. This patch enables the feature if bonding is selected. Note that unlike the bonding implemented before, this version is much simpler and may even enable multi path routing to a certain degree. Signed-off-by:
-
Simon Wunderlich authored
The current OGM sending an aggregation functionality decides on which interfaces a packet should be sent when it parses the forward packet struct. However, with the network wide multi interface optimization the outgoing interface is decided by the OGM processing function. This is reflected by moving the decision in the OGM processing function and add the outgoing interface in the forwarding packet struct. This practically implies that an OGM may be added multiple times (once per outgoing interface), and this also affects aggregation which needs to consider the outgoing interface as well. Signed-off-by:
-
Simon Wunderlich authored
If the same interface is used for sending and receiving, there might be throughput degradation on half-duplex interfaces such as WiFi. Add a penalty if the same interface is used to reflect this problem in the metric. At the same time, change the hop penalty from 30 to 15 so there will be no change for single wifi mesh network. the effective hop penalty will stay at 30 due to the new wifi penalty for these networks. Signed-off-by:
-
Simon Wunderlich authored
For the network wide multi interface optimization there are different routers for each outgoing interface (outgoing from the OGM perspective, incoming for payload traffic). To reflect this, change the router and associated data to a list of routers. While at it, rename batadv_orig_node_get_router() to batadv_orig_router_get() to follow the new naming scheme. Signed-off-by:
-
Simon Wunderlich authored
For the network wide multi interface optimization it is required to save metrics per outgoing interface in one neighbor. Therefore a new type is introduced to keep interface-specific information. This also requires some changes in access and list management. The compare and equiv_or_better API calls are changed to take the outgoing interface into consideration. Signed-off-by:
-
Simon Wunderlich authored
Remove bonding and interface alternating code - it will be replaced by a new, network-wide multi interface optimization which enables both bonding and interface alternating in a better way. Keep the sysfs and find router function though, this will be needed later. Signed-off-by:
-
David S. Miller authored
Sabrina Dubroca says: ==================== alx: add statistics Currently, the alx driver doesn't support statistics [1,2]. The original alx driver [3] that Johannes Berg modified provided statistics. This patch is an adaptation of the statistics code from the original driver to the alx driver included in the kernel. v4: - modified the assignements of hw stats to netstats (Ben Hutchings) - added comments to describe the stats fields (copied from atlx) v3: - renamed __alx_update_hw_stats to alx_update_hw_stats (Stephen Hemminger) v2: - use u64 instead of unsigned long (Ben Hutchings) - implement ndo_get_stats64 instead of ndo_get_stats (Ben Hutchings) - use EINVAL instead of ENOTSUPP (Ben Hutchings) - add BUILD_BUG_ON to check the size of the stats (Johannes Berg, Ben Hutchings) - add a comment regarding persistence of the stats (Stephen Hemminger) - align assignments in __alx_update_hw_stats [1] https://bugzilla.kernel.org/show_bug.cgi?id=63401 [2] http://www.spinics.net/lists/netdev/msg245544.html [3] https://github.com/mcgrof/alx ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sabrina Dubroca authored
Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Reviewed-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
-
Sabrina Dubroca authored
Signed-off-by:
-
Sabrina Dubroca authored
Signed-off-by:
-
Sabrina Dubroca authored
Signed-off-by:
-
Sabrina Dubroca authored
Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-nextDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates This series contains updates to i40e and now i40evf. Most notable is Jacob's patch to add PTP support to i40e. Mitch cleans up additional memcpy's and use struct assignment instead. Then fixes long lines to appease checkpatch.pl. Mitch then provides a fix to keep us from spamming the log with confusing errors. If you use ip to change the MAC address of a VF while the VF driver is loaded, closing the VF interface or unloading the VF driver will cause the VF driver to remove the MAC filter for its original (now invalid) MAC address. Jesse cleans up macros which are no longer needed or used. I (Jeff) cleanup function header comments to ensure Doxygen/kdoc works correctly to generate documentation without warnings. Anjali fixes a bug where ethtool set-channels would return failure when configuring only one Rx queue. Then fixes a bug where the driver was erroneously exiting the driver unload path if one part of the unload failed. Shannon fixes if the IPV6EXADD but is set in the Rx descriptor status, there was an optional extension header with an alternate IP address detected and the hardware checksum was not handling the alternate IP address correctly. Then adjusts the ITR max and min values to match the hardware max value and recommended min value. Shannon makes sure to clear the PXE mode after the adminq is initialized. v2: - fix patch 14 "i40e: enable PTP" to address Richard Cochran's spelling catch and Ben Hutchings Kconfig, SIOCGHWTSTAMP and sizeof() suggestions - added Paul Gortmaker's i40evf fix patch v3: - fix patch 14 "i40e: enable PTP" to address Ben Hutchings concerns about a race with PTP init and cleanup and i40e_get_ts_info(). ==================== Signed-off-by:
-
- 11 Jan, 2014 17 commits
-
-
Paul Gortmaker authored
As of commit 7f12ad74 ("i40evf: transmit and receive functionality") the s390 builds (allyesconfig) fail with: drivers/net/ethernet/intel/i40evf/i40e_txrx.c: In function 'i40e_clean_rx_irq': drivers/net/ethernet/intel/i40evf/i40e_txrx.c:818:3: error: implicit declaration of function 'prefetch' make[5]: *** [drivers/net/ethernet/intel/i40evf/i40e_txrx.o] Error 1 due to an implicit assumption that the prototype from linux/prefetch.h will be present. Cc: Mitch Williams <mitch.a.williams@intel.com> Cc: Greg Rose <gregory.v.rose@intel.com> Signed-off-by:
Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by:
Shannon Nelson <shannon.nelson@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Catherine Sullivan authored
Update the driver version to 0.3.28-k. Signed-off-by:
Catherine Sullivan <catherine.sullivan@intel.com> Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by:
-
Shannon Nelson authored
Change the redundant "vsi VSI" to VSI. Change-ID: Ic16ea5820a99abc7831713cde39e7d032a7ba4d3 Signed-off-by:
Kavindya Deegala <kavindya.s.deegala@intel.com> Signed-off-by:
-
Jacob Keller authored
New feature: Enable PTP support in the i40e driver. Change-ID: I6a8e799f582705191f9583afb1b9231a8db96cc8 Cc: Richard Cochran <richardcochran@gmail.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
Matthew Vick <matthew.vick@intel.com> Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Signed-off-by:
-
Shannon Nelson authored
In the latest firmware the clear_pxe_mode function will use the AdminQ request, so call this after AdminQ is set up rather than relying on i40e_pf_reset() to clear the PXE mode. Change-ID: Ice8cba2e9cbc3c7bde0a0bcf8eaf5009abef040b Signed-off-by:
-
Shannon Nelson authored
Make sure the "new" qtx_head[q] register is cleared before enabling the Tx queue. Change-ID: I0c7a12815e343a5ae68807af172a35d6c6857935 Signed-off-by:
-
Shannon Nelson authored
Set the ITR max and min values to match the hardware max value and the recommended min value. These values are shifted right one bit because the register counts in 2 usec units, so leave a comment to explain. Change-ID: I289c27955cf6c566a6d21b95c3110b88cbb15dad Signed-off-by:
-
Shannon Nelson authored
If the IPV6EXADD bit is set in the Rx descriptor status, there was an optional extension header with an alternate IP address detected. The HW checksum offload doesn't handle the alternate IP address correctly so likely comes up with the wrong answer. Thus, if the bit is set we ignore the checksum offload value. Change-ID: I70ff8d38cdcddccf44107691cae13d0c07c284c8 Signed-off-by:
-
Mitch Williams authored
If you use ip to change the MAC address of a VF while the VF driver is loaded, closing the VF interface or unloading the VF driver will cause the VF driver to remove the MAC filter for its original (now invalid) MAC address. This would cause the PF driver to kick an error message to the log, and back to the VF driver. Since the VF driver has not really done anything naughty, let's not punish it. Don't check for MAC address overrides on the delete operation, just make sure it's a valid address. This keeps us from spamming the log with confusing errors. Change-ID: I1f051bd4014e50855457d928c9ee8b0766981b2f Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Signed-off-by:
-
Anjali Singhai Jain authored
Fix a bug where the driver was erroneously exiting the driver unload path if one part of the unload failed. Instead of the original way the driver should always continue when disabling and be sure to disable all queues. Change-ID: Ib8c81c596bc87c31d8e9ca97ebf871168475279d Signed-off-by:
Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by:
-
Anjali Singhai Jain authored
Fix a bug where ethtool set-channels would return failure when configuring only one Rx queue. Change-ID: Id833c48c17d71e352b30f3249f6acf9e7aaec57e Signed-off-by:
-
Jeff Kirsher authored
These changes make Doxygen/kdoc work correctly without warnings. Change-ID: I2941f38860be805ff7548d84dae35754c83f1d62 Signed-off-by:
-
Mitch Williams authored
Avoid over-length lines in order to appease checkpatch. Change-ID: I63820a710acf798f49d2f85c610228711af84f72 Signed-off-by:
-
Catherine Sullivan authored
Update driver version to 0.3.27-k Signed-off-by:
-
Anjali Singhai Jain authored
The current driver will warn the user if the NVM version is out of date, this raises the bar to a newer version. Change-ID: I5ec21d8efa4e7c3fdacb56f85d310bb2229b1483 Signed-off-by:
-
Jesse Brandeburg authored
A previous commit removed any need for these macros, so remove them too. Signed-off-by:
-
Mitch Williams authored
These instances were found by coccinelle/spatch, and can use struct assignment instead of memcpy. Change-ID: Idc23c3599241bf8a658bda18c80417af3fbfee66 Signed-off-by:
Sibai Li <sibai.li@intel.com> Tested-by:
-
- 10 Jan, 2014 9 commits
-
-
git://git.open-mesh.org/linux-mergeDavid S. Miller authored
Included changes: - substitute FSF address with URL - deselect current bat-GW when GW-client mode gets deactivated - send every DHCP packet using bat-unicast messages when GW-client mode is enabled - implement the Extended Isolation mechanism (it is an enhancement of the already existing batman-AP-isolation). This mechanism allows the user to drop packets exchanged by selected clients by using netfilter marks. - fix typ0 in header guard - minor code cleanups Signed-off-by: -
David S. Miller authored
Christoph Paasch says: ==================== Make tcp-metrics source-address aware Currently tcp-metrics only stores per-destination addresses. This brings problems, when a host has multiple interfaces (e.g., a smartphone having WiFi/3G): For example, a host contacting a server over WiFi will store the tcp-metrics per destination IP. If then the host contacts the same server over 3G, the same tcp-metrics will be used, although the path-characteristics are completly different (e.g., the ssthresh is probably not the same). In case of TFO this is not a problem, as the server will provide us a new cookie once he saw our SYN+DATA with an incorrect cookie. It may be (in case of carrier-grade NAT), that we keep the same public IP but have a different private IP. Thus, we better reuse the old cookie even if our source-IP has changed. However, this scenario is probably very uncommon, as carriers try to provide the same src-IP to the clients behind their CGN. Patches 1 + 2 add the source-IP to the tcp metrics. Patches 3 to 5 modify the netlink-api to support the source-IP. From now on, when using the command "ip tcp_metrics delete address ADDRESS" all entries which match this destination IP will be deleted. Today's iproute2 will complain when doing "ip tcp_metrics flush PREFIX" if several entries are present for the same destination-IP but with different source-IPs: root@client:~/test# ip tcp_metrics 10.2.1.2 age 3.640sec rtt 16250us rttvar 15000us cwnd 10 10.2.1.2 age 4.030sec rtt 18750us rttvar 15000us cwnd 10 root@client:~/test# ip tcp_metrics flush 10.2.1.2/16 Failed to send flush request : No such process Follow-up patches will modify iproute2 to handle this correctly and allow specifying the source-IP in the get/del commands. v2: Added the patch that allows to selectively get/del of tcp-metrics based on src-IP and moved the patch that adds the new netlink attribute before the other patches. ==================== Signed-off-by: -
Christoph Paasch authored
We want to be able to get/del tcp-metrics based on the src IP. This patch adds the necessary parsing of the netlink attribute and if the source address is set, it will match on this one too. Signed-off-by:
Christoph Paasch <christoph.paasch@uclouvain.be> Signed-off-by:
-
Christoph Paasch authored
As we now can have multiple entries per destination-IP, the "ip tcp_metrics delete address ADDRESS" command deletes all of them. Signed-off-by:
-
Christoph Paasch authored
This patch adds a new netlink attribute for the source-IP and appends it to the netlink reply. Now, iproute2 can have access to the source-IP. Signed-off-by:
-
Christoph Paasch authored
We add the source-address to the tcp-metrics, so that different metrics will be used per source/destination-pair. We use the destination-hash to store the metric inside the hash-table. That way, deleting and dumping via "ip tcp_metrics" is easy. Signed-off-by:
-
Christoph Paasch authored
As we will add also the source-address, we rename all accesses to the tcp-metrics address to use "daddr". Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-nextDavid S. Miller authored
John W. Linville says: ==================== Please pull these updates for the 3.14 stream! For the mac80211 bits, Johannes says: "Felix adds some helper functions for P2P NoA software tracking, Joe fixes alignment (but as this apparently never caused issues I didn't send it to 3.13), Kyeyoon/Jouni add QoS-mapping support (a Hotspot 2.0 feature), Weilong fixed a bunch of checkpatch errors and I get to play fire-fighter or so and clean up other people's locking issues. I also added nl80211 vendor-specific events, as we'd discussed at the wireless summit." For the iwlwifi bits, Emmanuel says: "I have here a rework of the interrupt handling to meet RT kernel requirements - basically we don't take any lock in the primary interrupt handler. This gave me a good reason to clean things up a bit on the way. There is also a fix of the QoS mapping along with a few workarounds for hardware / firmware issues that are hard to hit. Three fixes suggested by static analyzers, and other various stuff. Most importantly, I update the Copyright note to include the new year." For the bluetooth bits, Gustavo says: "More patches to 3.14. The bulk of changes here is the 6LoWPAN support for Bluetooth LE Devices. The commits that touches net/ieee802154/ are already acked by David Miller. Other than that we have some RFCOMM fixes and improvements plus fixes and clean ups all over the tree." Beyond that, ath9k, brcmfmac, mwifiex, and wil6210 get their usual level of attention. The wl1251 driver gets a number of updates, and there are a handful of other bits here and there. ==================== Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-nextDavid S. Miller authored
Pablo Neira Ayuso says: ==================== This batch contains one single patch with the l2tp match for xtables, from James Chapman. ==================== Signed-off-by:
-
