* Use the buffer content length as opposed to the total buffer size.  This can
   be a real problem when using the mos7840 as a usb serial-console as all
   kernel output is truncated during boot.
Signed-off-by: Mark Ferrell <mferrell@uplogix.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The usb message must be saved also in case the USB endpoint is not a
control endpoint (i.e., "endpoint 0"), otherwise in some circumstances
we don't have a payload in case of error.

The patch has been created by tracing with usbmon the different error
messages generated by this driver with respect to the ehci-hcd driver.
Signed-off-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Tested-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit 354ab856 titled
"Fix OMAP EHCI suspend/resume failure (i693)" is causing
the usb hub and device detection fails in beagle XM
causeing NFS not functional. This affects the core retention too.
The same commit logic needs to be revisted adhering to hwmod and
device tree framework.
for now, this commit id 354ab856
titled "Fix OMAP EHCI suspend/resume failure (i693)" reverted.

This patch is validated on BeagleXM with NFS support over
usb ethernet and USB mass storage and other device detection.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit "5e0aa49e usb: chipidea: use generic map/unmap routines",
the udc part of the chipidea driver needs the generic usb gadget helper
functions. If the chipidea driver with udc support is built into the
kernel and usb gadget is built a module, the linking of the kernel
fails with:

drivers/built-in.o: In function `_hardware_dequeue':
drivers/usb/chipidea/udc.c:527:
    undefined reference to `usb_gadget_unmap_request'
drivers/usb/chipidea/udc.c:1269:
    undefined reference to `usb_gadget_unmap_request'
drivers/usb/chipidea/udc.c:1821:
    undefined reference to `usb_del_gadget_udc'
drivers/usb/chipidea/udc.c:443:
    undefined reference to `usb_gadget_map_request'
drivers/usb/chipidea/udc.c:1774:
    undefined reference to `usb_add_gadget_udc'

This patch changes the dependencies, so that udc support can only be
activated if the linux gadget support (USB_GADGET) is builtin or both
chipidea driver and USB_GADGET are modular. Same dependencies for the
chipidea host support and the linux host side USB support (USB).

While there, fix the indention of chipidea the help text.

Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In this patch, we add new declarations into option.c to support the new
interfaces of Huawei Data Card devices. And at the same time, remove the
redundant declarations from option.c.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds VID/PID for Kondo Kagaku Co. Ltd. Serial USB Adapter
interface:
http://www.kondo-robot.com/EN/wp/?cat=28

Tested by controlling an RCB3 board using libRCB3.
Signed-off-by: Ozan Çağlayan <ozancag@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'for-usb-linus-2012-08-09' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

Intel xhci: Work around immediate reboot on shutdown.

Hi Greg,

I'm cleaning out my queue before I leave on vacation tomorrow, so here's
one more patch for 3.6.  It works around an issue on a couple Intel
Panther Point desktop systems that cause them to reboot about 10 seconds
after the user shutdowns the system.

Sarah Sharp

The Intel desktop boards DH77EB and DH77DF have a hardware issue that
can be worked around by BIOS.  If the USB ports are switched to xHCI on
shutdown, the xHCI host will send a spurious interrupt, which will wake
the system.  Some BIOS will work around this, but not all.

The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.  The Intel Windows driver switches the ports back to EHCI, so
change the Linux xHCI driver to do the same.

Unfortunately, we can't tell the two effected boards apart from other
working motherboards, because the vendors will change the DMI strings
for the DH77EB and DH77DF boards to their own custom names.  One example
is Compulab's mini-desktop, the Intense-PC.  Instead, key off the
Panther Point xHCI host PCI vendor and device ID, and switch the ports
over for all PPT xHCI hosts.

The only impact this will have on non-effected boards is to add a couple
hundred milliseconds delay on boot when the BIOS has to switch the ports
over from EHCI to xHCI.

This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c2 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Denis Turischev <denis@compulab.co.il>
Tested-by: Denis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org

Merge tag 'for-usb-linus-2012-08-08' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

xHCI bug fixes and host quirks.

Hi Greg,

Here's four patches for 3.6.  Most are marked for stable as well.

The first one makes the xHCI driver load properly on newer Rensas hosts.
The next two fix issues with the Etron host incorrectly marking short
transfers as successful, and avoiding log warning spam for hosts that
make the same mistake.

The last patch fixes a really nasty xHCI driver bug that could cause
general protection faults when devices stall transfers.

Sarah Sharp

This patch fixes a particularly nasty bug that was revealed by the ring
expansion patches.  The bug has been present since the very beginning of
the xHCI driver history, and could have caused general protection faults
from bad memory accesses.

The first thing to note is that a Set TR Dequeue Pointer command can
move the dequeue pointer to a link TRB, if the canceled or stalled
transfer TD ended just before a link TRB.  The function to increment the
dequeue pointer, inc_deq, was written before cancellation and stall
support was added.  It assumed that the dequeue pointer could never
point to a link TRB.  It would unconditionally increment the dequeue
pointer at the start of the function, check if the pointer was now on a
link TRB, and move it to the top of the next segment if so.

This means that if a Set TR Dequeue Point command moved the dequeue
pointer to a link TRB, a subsequent call to inc_deq() would move the
pointer off the segment and into la-la-land.  It would then read from
that memory to determine if it was a link TRB.  Other functions would
often call inc_deq() until the dequeue pointer matched some other
pointer, which means this function would quite happily read all of
system memory before wrapping around to the right pointer value.

Often, there would be another endpoint segment from a different ring
allocated from the same DMA pool, which would be contiguous to the
segment inc_deq just stepped off of.  inc_deq would eventually find the
link TRB in that segment, and blindly move the dequeue pointer back to
the top of the correct ring segment.

The only reason the original code worked at all is because there was
only one ring segment.  With the ring expansion patches, the dequeue
pointer would eventually wrap into place, but the dequeue segment would
be out-of-sync.  On the second TD after the dequeue pointer was moved to
a link TRB, trb_in_td() would fail (because the dequeue pointer and
dequeue segment were out-of-sync), and this message would appear:

ERROR Transfer event TRB DMA ptr not part of current TD

This fixes bugzilla entry 4333 (option-based modem unhappy on USB 3.0
port: "Transfer event TRB DMA ptr not part of current TD", "rejecting
I/O to offline device"),

	https://bugzilla.kernel.org/show_bug.cgi?id=43333

and possibly other general protection fault bugs as well.

This patch should be backported to kernels as old as 2.6.31.  A separate
patch will be created for kernels older than 3.4, since inc_deq was
modified in 3.4 and this patch will not apply.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: James Ettle <theholyettlz@googlemail.com>
Tested-by: Matthew Hall <mhall@mhcomputing.net>
Cc: stable@vger.kernel.org

Merge tag 'fixes-for-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

usb: fixes for v3.6-rc1

Here are three fixes for v3.6-rc1. All on the MUSB driver and
quite obvious. First there's a Kconfig change which was missed
earlier, then there is a fix for the usage of the resource name
and lastly a fix for pm_runtime usage and device initialization.

The last fix is rather critical as it can end up in situations
where we try to access device's register with clocks disabled,
which will cause a Data Abort exception (on ARM).

When we encounter an xHCI host that needs the XHCI_TRUST_TX_LENGTH
quirk, the xHCI driver ends up spewing messages about the quirk into
dmesg every time a short packet occurs.  Change the xHCI driver to
rate-limit such warnings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Matthew Hall <mhall@mhcomputing.net>
Reported-by: Gary E. Miller <gem@rellim.com>

Gary reports that with recent kernels, he notices more xHCI driver
warnings:

xhci_hcd 0000:03:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?

We think his Etron xHCI host controller may have the same buggy behavior
as the Fresco Logic xHCI host.  When a short transfer is received, the
host will mark the transfer as successfully completed when it should be
marking it with a short completion.

Fix this by turning on the XHCI_TRUST_TX_LENGTH quirk when the Etron
host is discovered.  Note that Gary has revision 1, but if Etron fixes
this bug in future revisions, the quirk will have no effect.

This patch should be backported to kernels as old as 2.6.36, that
contain a backported version of commit
1530bbc6 "xhci: Add new short TX quirk
for Fresco Logic host."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Gary E. Miller <gem@rellim.com>
Cc: stable@vger.kernel.org

The NEC/Renesas 720201 xHCI host controller does not complete its reset
within 250 milliseconds.  In fact, it takes about 9 seconds to reset the
host controller, and 1 second for the host to be ready for doorbell
rings.  Extend the reset and CNR polling timeout to 10 seconds each.

This patch should be backported to kernels as old as 2.6.31, that
contain the commit 66d4eadd "USB: xhci:
BIOS handoff and HW initialization."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Edwin Klein Mentink <e.kleinmentink@zonnet.nl>
Cc: stable@vger.kernel.org

The clock need to be enabled before the musb_core platform device is
created and registered.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

We are overwriting the resource->name to "mc" so that musb_core.c
can understand it but this is also changing the platform device's
resource->name as the "name" address remains same.

Fixing the same by changing the resource->name field of local
structure only.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Commit "bb6abcf4: ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to
SOC_AM33XX" and "33959553: ARM: OMAP2+: Kconfig: convert
SOC_OMAPTI81XX to SOC_TI81XX" has changed the SOC config for AM33XX
and TI81XX as shown below

CONFIG_SOC_OMAPAM33XX --> CONFIG_SOC_AM33XX
CONFIG_SOC_OMAPTI81XX --> CONFIG_SOC_TI81XX

So updating the same at musb driver for AM33XX and TI81XX platforms.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Pull OLPC platform updates from Andres Salomon:
 "These move the OLPC Embedded Controller driver out of
  arch/x86/platform and into drivers/platform/olpc.

  OLPC machines are now ARM-based (which means lots of x86 and ARM
  changes), but are typically pretty self-contained..  so it makes more
  sense to go through a separate OLPC tree after getting the appropriate
  review/ACKs."

* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
  x86: OLPC: move s/r-related EC cmds to EC driver
  Platform: OLPC: move global variables into priv struct
  Platform: OLPC: move debugfs support from x86 EC driver
  x86: OLPC: switch over to using new EC driver on x86
  Platform: OLPC: add a suspended flag to the EC driver
  Platform: OLPC: turn EC driver into a platform_driver
  Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
  drivers: OLPC: update various drivers to include olpc-ec.h
  Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver

Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
 "This contains a set of device-tree conversions for Marvell Orion
  platforms that were staged early but took a few tries to get the
  branch into a format where it was suitable for us to pick up.

  Given that most people working on these platforms are hobbyists with
  limited time, we were a bit more flexible with merging it even though
  it came in late."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  ARM: Kirkwood: Replace mrvl with marvell
  ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
  ARM: Kirkwood: Describe Dreamplug LEDs in DT.
  ARM: Kirkwood: Describe iConnects LEDs in DT.
  ARM: Kirkwood: Describe iConnects temperature sensor in DT.
  ARM: Kirkwood: Describe IB62x0 LEDs in DT.
  ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
  ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
  ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
  ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
  ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
  ARM: Kirkwood: Use DT to configure SATA device.
  ARM: kirkwood: use devicetree for SPI on dreamplug
  ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
  ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
  ARM: Kirkwood: Add basic device tree support for QNAP TS219.
  ATA: sata_mv: Add device tree support
  ARM: Orion: DTify the watchdog timer.
  ARM: Orion: Add arch support needed for I2C via DT.
  ARM: kirkwood: use devicetree for orion-spi
  ...

Conflicts:
	drivers/watchdog/orion_wdt.c

Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
 "Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
  but didn't go in because the pull request ended up rejected.  So it
  just got merged, and we got this staged branch that enables the
  coupled cpuidle code on OMAP.

  With a stable git workflow from the other maintainer we could have
  staged this earlier, but that wasn't the case so we have had to merge
  it late.

  The alternative is to hold it off until 3.7 but given that the code is
  well-isolated to OMAP and they are eager to see it go in, I didn't
  push back hard in that direction."

* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP4: CPUidle: Open broadcast clock-event device.
  ARM: OMAP4: CPUidle: add synchronization for coupled idle states
  ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
  ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes for merge window fallout, and a bugfix for timer resume on
  PRIMA2."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: mmp: add missing irqs.h
  arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
  ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
  ARM: mxc: Include missing irqs.h header

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
  sh: explicitly include sh_dma.h in setup-sh7722.c
  sh: ecovec: care CN5 VBUS if USB host mode
  sh: sh7724: fixup renesas_usbhs clock settings
  sh: intc: initial irqdomain support.
  sh: pfc: Fix up init ordering mess.
  serial: sh-sci: fix compilation breakage, when DMA is enabled
  dmaengine: shdma: restore partial transfer calculation
  sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
  sh: Fix up recursive fault in oops with unset TTB.
  sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
  sh: select the fixed regulator driver on several boards
  sh: ecovec: switch MMC power control to regulators
  sh: add fixed voltage regulators to se7724
  sh: add fixed voltage regulators to sdk7786
  sh: add fixed voltage regulators to rsk
  sh: add fixed voltage regulators to migor
  sh: add fixed voltage regulators to kfr2r09
  sh: add fixed voltage regulators to ap325rxa
  sh: add fixed voltage regulators to sh7757lcr
  sh: add fixed voltage regulators to sh2007
  ...

Pull additional md update from NeilBrown:
 "This contains a few patches that depend on plugging changes in the
  block layer so needed to wait for those.

  It also contains a Kconfig fix for the new RAID10 support in dm-raid."

* tag 'md-3.6' of git://neil.brown.name/md:
  md/dm-raid: DM_RAID should select MD_RAID10
  md/raid1: submit IO from originating thread instead of md thread.
  raid5: raid5d handle stripe in batch way
  raid5: make_request use batch stripe release

Pull two ceph fixes from Sage Weil:
 "The first patch fixes up the old crufty open intent code to use the
  atomic_open stuff properly, and the second fixes a possible null deref
  and memory leak with the crypto keys."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: fix crypto key null deref, memory leak
  ceph: simplify+fix atomic_open

Merge tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 - Fixes a bug when the lower filesystem mount options include 'acl',
   but the eCryptfs mount options do not
 - Cleanups in the messaging code
 - Better handling of empty files in the lower filesystem to improve
   usability.  Failed file creations are now cleaned up and empty lower
   files are converted into eCryptfs during open().
 - The write-through cache changes are being reverted due to bugs that
   are not easy to fix.  Stability outweighs the performance
   enhancements here.
 - Improvement to the mount code to catch unsupported ciphers specified
   in the mount options

* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: check for eCryptfs cipher support at mount
  eCryptfs: Revert to a writethrough cache model
  eCryptfs: Initialize empty lower files when opening them
  eCryptfs: Unlink lower inode when ecryptfs_create() fails
  eCryptfs: Make all miscdev functions use daemon ptr in file private_data
  eCryptfs: Remove unused messaging declarations and function
  eCryptfs: Copy up POSIX ACL and read-only flags from lower mount

Pull CIFS update from Steve French:
 "Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.

  I am holding up a few more days on merging the remainder of the
  SMB2/SMB2.1 enablement although it is nearing review completion, in
  order to address some review comments from Jeff Layton on a few of the
  subsequent SMB2 patches, and also to debug an unrelated cifs problem
  that Pavel discovered."

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Add SMB2 support for rmdir
  CIFS: Move rmdir code to ops struct
  CIFS: Add SMB2 support for mkdir operation
  CIFS: Separate protocol specific part from mkdir
  CIFS: Simplify cifs_mkdir call

Borislav Petkov reports that the new warning added in commit
88fdf75d ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.

The call trace looks like this:

  x86_64_start_kernel ->
    x86_64_start_reservations ->
    start_kernel ->
    setup_arch ->
    paging_init ->
    zone_sizes_init ->
    free_area_init_nodes ->
    free_area_init_node

and (with the warning replaced by debug output), Borislav sees

  On node 0 totalpages: 4193848
    DMA zone: 64 pages used for memmap
    DMA zone: 6 pages reserved
    DMA zone: 3890 pages, LIFO batch:0
    DMA32 zone: 16320 pages used for memmap
    DMA32 zone: 798464 pages, LIFO batch:31
    Normal zone: 52736 pages used for memmap
    Normal zone: 3322368 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 4423680      <----
  On node 1 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 8617984      <----
  On node 2 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 12812288     <----
  On node 3 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31

so remove the bogus warning for now to avoid annoying people.  Minchan
Kim is looking at it.
Reported-by: Borislav Petkov <bp@amd64.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch/arm/mach-mmp/gplugd.c:195:13: error: ‘MMP_NR_IRQS’ undeclared here
(not in a function)
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1

Include <mach/irqs.h> to fix this issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The only way to write LATCHED registers to write LATCH_BIT to LATCH register,
that will latch COUNTER into LATCHED.e.g.
writel_relaxed(SIRFSOC_TIMER_LATCH_BIT, sirfsoc_timer_base +
	SIRFSOC_TIMER_LATCH);

Writing values to LATCHED registers directly is useless at all.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Avoid crashing if the crypto key payload was NULL, as when it was not correctly
allocated and initialized.  Also, avoid leaking it.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>

The initial ->atomic_open op was carried over from the old intent code,
which was incomplete and didn't really work.  Replace it with a fresh
method.  In particular:

 * always attempt to do an atomic open+lookup, both for the create case
   and for lookups of existing files.
 * fix symlink handling by returning 1 to the VFS so that we can follow
   the link to its destination. This fixes a longstanding ceph bug (#2392).
Signed-off-by: Sage Weil <sage@inktank.com>

setup-sh7722.c defines several objects, whose types are defined in
sh_dma.h, so, it has to be included explicitly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Pull MIPS updates from Ralf Baechle:
 "The lion share of this pull request are fixes for clk-related breakage
  caused by other changes during this merge window.  For some platforms
  the fix was as simple as selecting HAVE_CLK, for others like the
  Loongson 2 significant restructuring was required.

  The remainder are changes required to get the Lantiq code to work
  again."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Loongson 2: Sort out clock managment.
  MIPS: Loongson 1: more clk support and add select HAVE_CLK
  MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
  MIPS: Lantiq: Platform specific CLK fixup
  MIPS: Lantiq: Add device_tree_init function
  MIPS: Lantiq: Fix interface clock and PCI control register offset

Pull UML fixes from Richard Weinberger:
 "This patch set contains mostly fixes and cleanups.  The UML tty driver
  uses now tty_port and is no longer broken like hell  :-)"

* 'for-linus-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Add arch/x86/um to MAINTAINERS
  um: pass siginfo to guest process
  um: fix ubd_file_size for read-only files
  um: pull interrupt_end() into userspace()
  um: split syscall_trace(), pass pt_regs to it
  um: switch UPT_SET_RETURN_VALUE and regs_return_value to pt_regs
  um: set BLK_CGROUP=y in defconfig
  um: remove count_lock
  um: fully use tty_port
  um: Remove dead code
  um: remove line_ioctl()
  TTY: um/line, use tty from tty_port
  TTY: um/line, add tty_port

Pull ARM DMA engine updates from Russell King:
 "This looks scary at first glance, but what it is is:
   - a rework of the sa11x0 DMA engine driver merged during the previous
     cycle, to extract a common set of helper functions for DMA engine
     implementations.
   - conversion of amba-pl08x.c to use these helper functions.
   - addition of OMAP DMA engine driver (using these helper functions),
     and conversion of some of the OMAP DMA users to use DMA engine.

  Nothing in the helper functions is ARM specific, so I hope that other
  implementations can consolidate some of their code by making use of
  these helpers.

  This has been sitting in linux-next most of the merge cycle, and has
  been tested by several OMAP folk.  I've tested it on sa11x0 platforms,
  and given it my best shot on my broken platforms which have the
  amba-pl08x controller.

  The last point is the addition to feature-removal-schedule.txt, which
  will have a merge conflict.  Between myself and TI, we're planning to
  remove the old TI DMA implementation next year."

Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}

* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
  ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
  ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
  Add feature removal of old OMAP private DMA implementation
  mtd: omap2: remove private DMA API implementation
  mtd: omap2: add DMA engine support
  spi: omap2-mcspi: remove private DMA API implementation
  spi: omap2-mcspi: add DMA engine support
  ARM: omap: remove mmc platform data dma_mask and initialization
  mmc: omap: remove private DMA API implementation
  mmc: omap: add DMA engine support
  mmc: omap_hsmmc: remove private DMA API implementation
  mmc: omap_hsmmc: add DMA engine support
  dmaengine: omap: add support for cyclic DMA
  dmaengine: omap: add support for setting fi
  dmaengine: omap: add support for returning residue in tx_state method
  dmaengine: add OMAP DMA engine driver
  dmaengine: sa11x0-dma: add cyclic DMA support
  dmaengine: sa11x0-dma: fix DMA residue support
  dmaengine: PL08x: ensure all descriptors are freed when channel is released
  dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
  ...

Pull ARM audit/signal updates from Russell King:
 "ARM audit/signal handling updates from Al and Will.  This improves on
  the work Viro did last merge window, and sorts out some of the issues
  found with that work."

* 'audit' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7475/1: sys_trace: allow all syscall arguments to be updated via ptrace
  ARM: 7474/1: get rid of TIF_SYSCALL_RESTARTSYS
  ARM: 7473/1: deal with handlerless restarts without leaving the kernel
  ARM: 7472/1: pull all work_pending logics into C function
  ARM: 7471/1: Revert "7442/1: Revert "remove unused restart trampoline""
  ARM: 7470/1: Revert "7443/1: Revert "new way of handling ERESTART_RESTARTBLOCK""

Pull ARM fixes from Russell King:
 "This fixes various issues found during July"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7479/1: mm: avoid NULL dereference when flushing gate_vma with VIVT caches
  ARM: Fix undefined instruction exception handling
  ARM: 7480/1: only call smp_send_stop() on SMP
  ARM: 7478/1: errata: extend workaround for erratum #720789
  ARM: 7477/1: vfp: Always save VFP state in vfp_pm_suspend on UP
  ARM: 7476/1: vfp: only clear vfp state for current cpu in vfp_pm_suspend
  ARM: 7468/1: ftrace: Trace function entry before updating index
  ARM: 7467/1: mutex: use generic xchg-based implementation for ARMv6+
  ARM: 7466/1: disable interrupt before spinning endlessly
  ARM: 7465/1: Handle >4GB memory sizes in device tree and mem=size@start option

Signed-off-by: Richard Weinberger <richard@nod.at>