There are devices that forbid MIMO by the mean of the NVM.
Detect thoses devices and forbid MIMO otherwise the firmware
would crash. STBC is still allowed on these devices.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

During firmware restart, the quota command isn't calculated multiple
times, but after the firmware restart it has to be sent, so force it.
Otherwise the firmware crashes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

I forgot to rename the CPTCFG_ prefix...

Fixes: 484b3d13 ("iwlwifi: mvm: add debugfs entry with the number of net-detect scans")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Our device needs two different firmwares: the INIT firmware
and the operational (OPER) firmware. The first one is run
when the driver loads and it returns calibrations results
as well as the NVM. The second one implements the WiFi
protocol.

If the wlan interface is not brought up, the device is put
to low power state: no firmware will be running. When the
interface is brought up, we would run the OPER firmware
only and reuse the results of the run of the INIT firmware
when the driver was loaded. This is changing with this
patch.
We now run the INIT firmware every time mac80211 calls
start(). The penalty for that is minimal since the INIT
firwmare run fast. I now also avoid to power down the device
between the INIT and OPER firmware on certains buses.

The motivation for this change is that there are components
on the device (MFUART) that are triggered by the INIT
firmware and need the device to be powered up in order to
keep running. Powering the device down between the INIT and
OPER firmware would stop these components and prevent them
from running again since they are triggered by the INIT
firmware only.
The new flow allows this and also allows to trigger these
components again when the interface is brought up after
it has been brought down.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In the case of a DMA mapping error on the last iteration of
the loop of the allocation of memory of the FW monitor we
indeed free the pages, but don't NULL out the page variable
thus allowing for the possibility of setting the FW monitor
variables with invalid data to use.

Fixes: c2d20201 ("iwlwifi: pcie: add firmware monitor capabilities")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If for some reason statistics notification received from the firmware
reports 0 in average beacon RSSI value, then skip it and avoid signal
based decisions.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Scan iteration complete notification handling uses the wrong FW API
version (version 2 instead of version 3).
Fix that by removing version 2 API which is no longer used, and using
only the updated version.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When the delay paramatere is provided, we need to stop
the collection only after the delay has elapsed.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware doesn't relate the scan to a vif. The scan is
run by a separate entity called auxiliary MAC (aka AUX MAC).
This AUX MAC needs to get Tx power limitations that are
not applied on a specific vif, but on the device as a whole.

This can be implemented by using the minimum of all the
values set by the user for all the MACs. But then we need
to ignore the limitations that come from the AP or
regulatory for a specific vif: a specific vif might have
regulatory limitations because of the channel is works on.
This limit is irrelevant for the AUX MAC.
Use the new API from mac80211: the user_power_level in
bss_conf to achieve this.

Firmware -13.ucode has already moved to this API.

Change-Id: Ifba83660f378e91b93bd46d29fe8ba35a7c168a4
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull networking updates from David Miller:

 1) Add BQL support to via-rhine, from Tino Reichardt.

 2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
    can support hw switch offloading.  From Floria Fainelli.

 3) Allow 'ip address' commands to initiate multicast group join/leave,
    from Madhu Challa.

 4) Many ipv4 FIB lookup optimizations from Alexander Duyck.

 5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
    Borkmann.

 6) Remove the ugly compat support in ARP for ugly layers like ax25,
    rose, etc.  And use this to clean up the neigh layer, then use it to
    implement MPLS support.  All from Eric Biederman.

 7) Support L3 forwarding offloading in switches, from Scott Feldman.

 8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
    up route lookups even further.  From Alexander Duyck.

 9) Many improvements and bug fixes to the rhashtable implementation,
    from Herbert Xu and Thomas Graf.  In particular, in the case where
    an rhashtable user bulk adds a large number of items into an empty
    table, we expand the table much more sanely.

10) Don't make the tcp_metrics hash table per-namespace, from Eric
    Biederman.

11) Extend EBPF to access SKB fields, from Alexei Starovoitov.

12) Split out new connection request sockets so that they can be
    established in the main hash table.  Much less false sharing since
    hash lookups go direct to the request sockets instead of having to
    go first to the listener then to the request socks hashed
    underneath.  From Eric Dumazet.

13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.

14) Support stable privacy address generation for RFC7217 in IPV6.  From
    Hannes Frederic Sowa.

15) Hash network namespace into IP frag IDs, also from Hannes Frederic
    Sowa.

16) Convert PTP get/set methods to use 64-bit time, from Richard
    Cochran.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
  fm10k: Bump driver version to 0.15.2
  fm10k: corrected VF multicast update
  fm10k: mbx_update_max_size does not drop all oversized messages
  fm10k: reset head instead of calling update_max_size
  fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
  fm10k: update xcast mode before synchronizing multicast addresses
  fm10k: start service timer on probe
  fm10k: fix function header comment
  fm10k: comment next_vf_mbx flow
  fm10k: don't handle mailbox events in iov_event path and always process mailbox
  fm10k: use separate workqueue for fm10k driver
  fm10k: Set PF queues to unlimited bandwidth during virtualization
  fm10k: expose tx_timeout_count as an ethtool stat
  fm10k: only increment tx_timeout_count in Tx hang path
  fm10k: remove extraneous "Reset interface" message
  fm10k: separate PF only stats so that VF does not display them
  fm10k: use hw->mac.max_queues for stats
  fm10k: only show actual queues, not the maximum in hardware
  fm10k: allow creation of VLAN on default vid
  fm10k: fix unused warnings
  ...

Pull ARM updates from Russell King:
 "Included in this update are both some long term fixes and some new
  features.

  Fixes:

   - An integer overflow in the calculation of ELF_ET_DYN_BASE.

   - Avoiding OOMs for high-order IOMMU allocations

   - SMP requires the data cache to be enabled for synchronisation
     primitives to work, so prevent the CPU_DCACHE_DISABLE option being
     visible on SMP builds.

   - A bug going back 10+ years in the noMMU ARM94* CPU support code,
     where it corrupts registers.  Found by folk getting Linux running
     on their cameras.

   - Versatile Express needs an errata workaround enabled for CPU
     hot-unplug to work.

  Features:

   - Clean up module linker by handling out of range relocations
     separately from relocation cases we don't handle.

   - Fix a long term bug in the pci_mmap_page_range() code, which we
     hope won't impact userspace (we hope there's no users of the
     existing broken interface.)

   - Don't map DMA coherent allocations when we don't have a MMU.

   - Drop experimental status for SMP_ON_UP.

   - Warn when DT doesn't specify ePAPR mandatory cache properties.

   - Add documentation concerning how we find the start of physical
     memory for AUTO_ZRELADDR kernels, detailing why we have chosen the
     mask and the implications of changing it.

   - Updates from Ard Biesheuvel to address some issues with large
     kernels (such as allyesconfig) failing to link.

   - Allow hibernation to work on modern (ARMv7) CPUs - this appears to
     have never worked in the past on these CPUs.

   - Enable IRQ_SHOW_LEVEL, which changes the /proc/interrupts output
     format (hopefully without userspace breaking...  let's hope that if
     it causes someone a problem, they tell us.)

   - Fix tegra-ahb DT offsets.

   - Rework ARM errata 643719 code (and ARMv7 flush_cache_louis()/
     flush_dcache_all()) code to be more efficient, and enable this
     errata workaround by default for ARMv7+SMP CPUs.  This complements
     the Versatile Express fix above.

   - Rework ARMv7 context code for errata 430973, so that only Cortex A8
     CPUs are impacted by the branch target buffer flush when this
     errata is enabled.  Also update the help text to indicate that all
     r1p* A8 CPUs are impacted.

   - Switch ARM to the generic show_mem() implementation, it conveys all
     the information which we were already reporting.

   - Prevent slow timer sources being used for udelay() - timers running
     at less than 1MHz are not useful for this, and can cause udelay()
     to return immediately, without any wait.  Using such a slow timer
     is silly.

   - VDSO support for 32-bit ARM, mainly for gettimeofday() using the
     ARM architected timer.

   - Perf support for Scorpion performance monitoring units"

vdso semantic conflict fixed up as per linux-next.

* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (52 commits)
  ARM: update errata 430973 documentation to cover Cortex A8 r1p*
  ARM: ensure delay timer has sufficient accuracy for delays
  ARM: switch to use the generic show_mem() implementation
  ARM: proc-v7: avoid errata 430973 workaround for non-Cortex A8 CPUs
  ARM: enable ARM errata 643719 workaround by default
  ARM: cache-v7: optimise test for Cortex A9 r0pX devices
  ARM: cache-v7: optimise branches in v7_flush_cache_louis
  ARM: cache-v7: consolidate initialisation of cache level index
  ARM: cache-v7: shift CLIDR to extract appropriate field before masking
  ARM: cache-v7: use movw/movt instructions
  ARM: allow 16-bit instructions in ALT_UP()
  ARM: proc-arm94*.S: fix setup function
  ARM: vexpress: fix CPU hotplug with CT9x4 tile.
  ARM: 8276/1: Make CPU_DCACHE_DISABLE depend on !SMP
  ARM: 8335/1: Documentation: DT bindings: Tegra AHB: document the legacy base address
  ARM: 8334/1: amba: tegra-ahb: detect and correct bogus base address
  ARM: 8333/1: amba: tegra-ahb: fix register offsets in the macros
  ARM: 8339/1: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
  ARM: 8338/1: kexec: Relax SMP validation to improve DT compatibility
  ARM: 8337/1: mm: Do not invoke OOM for higher order IOMMU DMA allocations
  ...

Pull s390 updates from Martin Schwidefsky:
 "The major change in this merge is the removal of the support for
  31-bit kernels.  Naturally 31-bit user space will continue to work via
  the compat layer.

  And then some cleanup, some improvements and bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (23 commits)
  s390/smp: wait until secondaries are active & online
  s390/hibernate: fix save and restore of kernel text section
  s390/cacheinfo: add missing facility check
  s390/syscalls: simplify syscall_get_arch()
  s390/irq: enforce correct irqclass_sub_desc array size
  s390: remove "64" suffix from mem64.S and swsusp_asm64.S
  s390/ipl: cleanup macro usage
  s390/ipl: cleanup shutdown_action attributes
  s390/ipl: cleanup bin attr usage
  s390/uprobes: fix address space annotation
  s390: add missing arch_release_task_struct() declaration
  s390: make couple of functions and variables static
  s390/maccess: improve s390_kernel_write()
  s390/maccess: remove potentially broken probe_kernel_write()
  s390/watchdog: support for KVM hypervisors and delete pr_info messages
  s390/watchdog: enable KEEPALIVE for /dev/watchdog
  s390/dasd: remove setting of scheduler from driver
  s390/traps: panic() instead of die() on translation exception
  s390: remove test_facility(2) (== z/Architecture mode active) checks
  s390/cmpxchg: simplify cmpxchg_double
  ...

Pull power management and ACPI updates from Rafael Wysocki:
 "These are mostly fixes and cleanups all over, although there are a few
  items that sort of fall into the new feature category.

  First off, we have new callbacks for PM domains that should help us to
  handle some issues related to device initialization in a better way.

  There also is some consolidation in the unified device properties API
  area allowing us to use that inferface for accessing data coming from
  platform initialization code in addition to firmware-provided data.

  We have some new device/CPU IDs in a few drivers, support for new
  chips and a new cpufreq driver too.

  Specifics:

   - Generic PM domains support update including new PM domain callbacks
     to handle device initialization better (Russell King, Rafael J
     Wysocki, Kevin Hilman)

   - Unified device properties API update including a new mechanism for
     accessing data provided by platform initialization code (Rafael J
     Wysocki, Adrian Hunter)

   - ARM cpuidle update including ARM32/ARM64 handling consolidation
     (Daniel Lezcano)

   - intel_idle update including support for the Silvermont Core in the
     Baytrail SOC and for the Airmont Core in the Cherrytrail and
     Braswell SOCs (Len Brown, Mathias Krause)

   - New cpufreq driver for Hisilicon ACPU (Leo Yan)

   - intel_pstate update including support for the Knights Landing chip
     (Dasaratharaman Chandramouli, Kristen Carlson Accardi)

   - QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)

   - powernv cpufreq driver update (Shilpasri G Bhat)

   - devfreq update including Tegra support changes (Tomeu Vizoso,
     MyungJoo Ham, Chanwoo Choi)

   - powercap RAPL (Running-Average Power Limit) driver update including
     support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)

   - ACPI device enumeration update related to the handling of the
     special PRP0001 device ID allowing DT-style 'compatible' property
     to be used for ACPI device identification (Rafael J Wysocki)

   - ACPI EC driver update including limited _DEP support (Lan Tianyu,
     Lv Zheng)

   - ACPI backlight driver update including a new mechanism to allow
     native backlight handling to be forced on non-Windows 8 systems and
     a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)

   - New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)

   - Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
     Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)

   - Fixes related to suspend-to-idle for the iTCO watchdog driver and
     the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)

   - PM tracing support for the suspend phase of system suspend/resume
     transitions (Zhonghui Fu)

   - Configurable delay for the system suspend/resume testing facility
     (Brian Norris)

   - PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"

* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
  ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
  ACPI / scan: Rework modalias creation when "compatible" is present
  intel_idle: mark cpu id array as __initconst
  powercap / RAPL: mark rapl_ids array as __initconst
  powercap / RAPL: add ID for Broadwell server
  intel_pstate: Knights Landing support
  intel_pstate: remove MSR test
  cpufreq: fix qoriq uniprocessor build
  ACPI / scan: Take the PRP0001 position in the list of IDs into account
  ACPI / scan: Simplify acpi_match_device()
  ACPI / scan: Generalize of_compatible matching
  device property: Introduce firmware node type for platform data
  device property: Make it possible to use secondary firmware nodes
  PM / watchdog: iTCO: stop watchdog during system suspend
  cpufreq: hisilicon: add acpu driver
  ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
  cpufreq: powernv: Report cpu frequency throttling
  intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
  intel_idle: Update support for Silvermont Core in Baytrail SOC
  PM / devfreq: tegra: Register governor on module init
  ...

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-04-14

This series contains updates to fm10k only.

Fixed transmit statistics which was actually using values from the
receive ring, instead of the transmit ring.  Fixed up spelling mistakes
in code comments and resolved unused argument warnings.  Added support
for netconsole.  Fixed up statistic reporting so that we are only
reporting from actual queues as well as display PF only stats for
just the PF and not the VF.  Also fixed an issue that when returning
virtualization queues from the VF back to the PF, we were retaining
the VF rate limiter.

Fixed up the driver to use a separate workqueue, which helps reduce
and stabilize latency between scheduling the work in our interrupt and
actually performing the work.

Fixed a bug where the VF tried to set a multicast address before
requesting the required xcast mode.

Fix VF multicast update since VFs were being improperly added to the
switch's mutlicast group.  The error stems from the fact that incorrect
arguments were passed to the update_mc_addr().

Thanks to Alex Duyck for the extensive review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull input subsystem updates from Dmitry Torokhov:
 "You will get the following new drivers:

   - Qualcomm PM8941 power key drver
   - ChipOne icn8318 touchscreen controller driver
   - Broadcom iProc touchscreen and keypad drivers
   - Semtech SX8654 I2C touchscreen controller driver

  ALPS driver now supports newer SS4 devices; Elantech got a fix that
  should make it work on some ASUS laptops; and a slew of other
  enhancements and random fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
  Input: alps - non interleaved V2 dualpoint has separate stick button bits
  Input: alps - fix touchpad buttons getting stuck when used with trackpoint
  Input: atkbd - document "no new force-release quirks" policy
  Input: ALPS - make alps_get_pkt_id_ss4_v2() and others static
  Input: ALPS - V7 devices can report 5-finger taps
  Input: ALPS - add support for SS4 touchpad devices
  Input: ALPS - refactor alps_set_abs_params_mt()
  Input: elantech - fix absolute mode setting on some ASUS laptops
  Input: atmel_mxt_ts - split out touchpad initialisation logic
  Input: atmel_mxt_ts - implement support for T100 touch object
  Input: cros_ec_keyb - fix clearing keyboard state on wakeup
  Input: gscps2 - drop pci_ids dependency
  Input: synaptics - allocate 3 slots to keep stability in image sensors
  Input: Revert "Revert "synaptics - use dmax in input_mt_assign_slots""
  Input: MT - make slot assignment work for overcovered solutions
  mfd: tc3589x: enforce device-tree only mode
  Input: tc3589x - localize platform data
  Input: tsc2007 - Convert msecs to jiffies only once
  Input: edt-ft5x06 - remove EV_SYN event report
  Input: edt-ft5x06 - allow to setting the maximum axes value through the DT
  ...

Pull i2c updates from Wolfram Sang:
 "Most notable:

   - introducing the i2c_quirk infrastructure.  Now, flaws of I2C
     controllers can be described and the core will check if the flaws
     collide with the messages to be sent

   - wait_for_completion return type cleanup series

   - new drivers for Digicolor, Netlogic XLP, Ingenic JZ4780

   - updates to the I2C slave framework which include API changes.  Its
     only user was updated, too.  Documentation was finally added

   - changed dynamic bus numbering for the DT case.  This could change
     bus numbers for users.  However, it fixes a collision where dynamic
     and static busses request the same id.

   - driver bugfixes, cleanups"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
  i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller
  of: Add vendor prefix 'netlogic'
  i2c: davinci: use ICPFUNC to toggle I2C as gpio for bus recovery
  i2c: davinci: use bus recovery infrastructure
  i2c: change input parameter to i2c_adapter for prepare/unprepare_recovery
  i2c: i2c-mux-gpio: remove error messages for probe deferrals
  i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780
  i2c: dln2: set the device tree node of the adapter
  i2c: davinci: fixup wait_for_completion_timeout handling
  i2c: mpc: Fix ISR return value
  i2c: slave-eeprom: add more info when to increase the pointer
  i2c: slave: add documentation for i2c-slave-eeprom
  Documentation: i2c: describe the new slave mode
  i2c: slave: rework the slave API
  i2c: add support for the Digicolor I2C controller
  i2c: busses with dynamic ids should start after fixed ids for DT
  of: base: add function to get highest id of an alias stem
  i2c: designware: Suppress error message if platform_get_irq() < 0
  i2c: mpc: assign the correct prescaler from SVR
  i2c: img-scb: fixup of wait_for_completion_timeout return handling
  ...

Pull VFIO updates from Alex Williamson:

 - VFIO platform bus driver support (Baptiste Reynal, Antonios Motakis,
   testing and review by Eric Auger)

 - Split VFIO irqfd support to separate module (Alex Williamson)

 - vfio-pci VGA arbiter client (Alex Williamson)

 - New vfio-pci.ids= module option (Alex Williamson)

 - vfio-pci D3 power state support for idle devices (Alex Williamson)

* tag 'vfio-v4.1-rc1' of git://github.com/awilliam/linux-vfio: (30 commits)
  vfio-pci: Fix use after free
  vfio-pci: Move idle devices to D3hot power state
  vfio-pci: Remove warning if try-reset fails
  vfio-pci: Allow PCI IDs to be specified as module options
  vfio-pci: Add VGA arbiter client
  vfio-pci: Add module option to disable VGA region access
  vgaarb: Stub vga_set_legacy_decoding()
  vfio: Split virqfd into a separate module for vfio bus drivers
  vfio: virqfd_lock can be static
  vfio: put off the allocation of "minor" in vfio_create_group
  vfio/platform: implement IRQ masking/unmasking via an eventfd
  vfio: initialize the virqfd workqueue in VFIO generic code
  vfio: move eventfd support code for VFIO_PCI to a separate file
  vfio: pass an opaque pointer on virqfd initialization
  vfio: add local lock for virqfd instead of depending on VFIO PCI
  vfio: virqfd: rename vfio_pci_virqfd_init and vfio_pci_virqfd_exit
  vfio: add a vfio_ prefix to virqfd_enable and virqfd_disable and export
  vfio/platform: support for level sensitive interrupts
  vfio/platform: trigger an interrupt via eventfd
  vfio/platform: initial interrupts support code
  ...

Pull pincontrol updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.1 development
  cycle.  Nothing really exciting this time: we basically added a few
  new drivers and subdrivers and stabilized them in linux-next.  Some
  cleanups too.  With sunrisepoint Intel has a real fine fully featured
  pin control driver for contemporary hardware, and the AMD driver is
  also for large deployments.  Most of the others are ARM devices.

  New drivers:
    - Intel Sunrisepoint
    - AMD KERNCZ GPIO
    - Broadcom Cygnus IOMUX

  New subdrivers:
    - Marvell MVEBU Armada 39x SoCs
    - Samsung Exynos 5433
    - nVidia Tegra 210
    - Mediatek MT8135
    - Mediatek MT8173
    - AMLogic Meson8b
    - Qualcomm PM8916

  On top of this cleanups and development history for the above drivers
  as issues were fixed after merging"

* tag 'pinctrl-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (71 commits)
  pinctrl: sirf: move sgpio lock into state container
  pinctrl: Add support for PM8916 GPIO's and MPP's
  pinctrl: bcm2835: Fix support for threaded level triggered IRQs
  sh-pfc: r8a7790: add EtherAVB pin groups
  pinctrl: Document "function" + "pins" pinmux binding
  pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support
  pinctrl: fsl: imx: Check for 0 config register
  pinctrl: Add support for Meson8b
  documentation: Extend pinctrl docs for Meson8b
  pinctrl: Cleanup Meson8 driver
  Fix inconsistent spinlock of AMD GPIO driver which can be recognized by static analysis tool smatch. Declare constant Variables with Sparse's suggestion.
  pinctrl: at91: convert __raw to endian agnostic IO
  pinctrl: constify of_device_id array
  pinctrl: pinconf-generic: add dt node names to error messages
  pinctrl: pinconf-generic: scan also referenced phandle node
  pinctrl: mvebu: add suspend/resume support to Armada XP pinctrl driver
  pinctrl: st: Display pin's function when printing pinctrl debug information
  pinctrl: st: Show correct pin direction also in GPIO mode
  pinctrl: st: Supply a GPIO get_direction() call-back
  pinctrl: st: Move st_get_pio_control() further up the source file
  ...

Pull backlight updates from Lee Jones:
 "Changes to existing drivers:

   - Use of_get_child_by_name() instead of refcount; 88pm860x_bl

   - Terminate array with NULL element; da9052_bl"

* tag 'backlight-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
  backlight: da9052_bl: Terminate da9052_wled_ids array with empty element
  backlight: 88pm860x_bl: Use of_get_child_by_name() instead of refcount hack

Pull MFD updates from Lee Jones:
 "Changes to existing drivers:

   - Rename child driver [axp288_battery => axp288_fuel_gauge]; axp20x
   - Rename child driver [max77693-flash => max77693-led]; max77693
   - Error handling fixes; intel_soc_pmic
   - GPIO tweaking; intel_soc_pmic
   - Remove non-DT code; vexpress-sysreg, tc3589x
   - Remove unused/legacy code; ti_am335x_tscadc, rts5249, rtsx_gops, rtsx_pcr,
                                rtc-s5m, sec-core, max77693, menelaus,
                                wm5102-tables
   - Trivial fixups; rtsx_pci, da9150-core, sec-core, max7769, max77693,
                     mc13xxx-core, dln2, hi6421-pmic-core, rk808, twl4030-power,
                     lpc_ich, menelaus, twl6040
   - Update register/address values; rts5227, rts5249
   - DT and/or binding document fixups; arizona, da9150, mt6397, axp20x,
                                        qcom-rpm, qcom-spmi-pmic
   - Couple of trivial core Kconfig fixups
   - Remove use of seq_printf return value; ab8500-debugfs
   - Remove __exit markups; menelaus, tps65010
   - Fix platform-device name collisions; mfd-core

  New drivers/supported devices:

   - Add support for wm8280/wm8281 into arizona
   - Add support for COMe-cBL6 into kempld-core
   - Add support for rts524a and rts525a into rts5249
   - Add support for ipq8064 into qcom_rpm
   - Add support for extcon into axp20x
   - New MediaTek MT6397 PMIC driver
   - New Maxim MAX77843 PMIC dirver
   - New Intel Quark X1000 I2C-GPIO driver
   - New Skyworks SKY81452 driver"

* tag 'mfd-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (76 commits)
  mfd: sec: Fix RTC alarm interrupt number on S2MPS11
  mfd: wm5102: Remove registers for output 3R from readable list
  mfd: tps65010: Remove incorrect __exit markups
  mfd: devicetree: bindings: Add Qualcomm RPM regulator subnodes
  mfd: axp20x: Add support for extcon cell
  mfd: lpc_ich: Sort IDs
  mfd: twl6040: Remove wrong and unneeded "platform:twl6040" modalias
  mfd: qcom-spmi-pmic: Add specific compatible strings for Qualcomm's SPMI PMIC's
  mfd: axp20x: Fix duplicate const for model names
  mfd: menelaus: Use macro for magic number
  mfd: menelaus: Drop support for SW controller VCORE
  mfd: menelaus: Delete omap_has_menelaus
  mfd: arizona: Correct type of gpio_defaults
  mfd: lpc_ich: Sort IDs
  mfd: Fix a typo in Kconfig
  mfd: qcom_rpm: Add support for IPQ8064
  mfd: devicetree: qcom_rpm: Document IPQ8064 resources
  mfd: core: Fix platform-device name collisions
  mfd: intel_quark_i2c_gpio: Don't crash if !DMI
  dt-bindings: Add vendor-prefix for X-Powers
  ...

Merge first patchbomb from Andrew Morton:

 - arch/sh updates

 - ocfs2 updates

 - kernel/watchdog feature

 - about half of mm/

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (122 commits)
  Documentation: update arch list in the 'memtest' entry
  Kconfig: memtest: update number of test patterns up to 17
  arm: add support for memtest
  arm64: add support for memtest
  memtest: use phys_addr_t for physical addresses
  mm: move memtest under mm
  mm, hugetlb: abort __get_user_pages if current has been oom killed
  mm, mempool: do not allow atomic resizing
  memcg: print cgroup information when system panics due to panic_on_oom
  mm: numa: remove migrate_ratelimited
  mm: fold arch_randomize_brk into ARCH_HAS_ELF_RANDOMIZE
  mm: split ET_DYN ASLR from mmap ASLR
  s390: redefine randomize_et_dyn for ELF_ET_DYN_BASE
  mm: expose arch_mmap_rnd when available
  s390: standardize mmap_rnd() usage
  powerpc: standardize mmap_rnd() usage
  mips: extract logic for mmap_rnd()
  arm64: standardize mmap_rnd() usage
  x86: standardize mmap_rnd() usage
  arm: factor out mmap ASLR into mmap_rnd
  ...

Since arm64/arm support memtest command line option update the "memtest"
entry.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Additional test patterns for memtest were introduced since commit
63823126 ("x86: memtest: add additional (regular) test patterns"),
but looks like Kconfig was not updated that time.

Update Kconfig entry with the actual number of maximum test patterns.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add support for memtest command line option.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add support for memtest command line option.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since memtest might be used by other architectures pass input parameters
as phys_addr_t instead of long to prevent overflow.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Memtest is a simple feature which fills the memory with a given set of
patterns and validates memory contents, if bad memory regions is detected
it reserves them via memblock API.  Since memblock API is widely used by
other architectures this feature can be enabled outside of x86 world.

This patch set promotes memtest to live under generic mm umbrella and
enables memtest feature for arm/arm64.

It was reported that this patch set was useful for tracking down an issue
with some errant DMA on an arm64 platform.

This patch (of 6):

There is nothing platform dependent in the core memtest code, so other
platforms might benefit from this feature too.

[linux@roeck-us.net: MEMTEST depends on MEMBLOCK]
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If __get_user_pages() is faulting a significant number of hugetlb pages,
usually as the result of mmap(MAP_LOCKED), it can potentially allocate a
very large amount of memory.

If the process has been oom killed, this will cause a lot of memory to
potentially deplete memory reserves.

In the same way that commit 4779280d ("mm: make get_user_pages()
interruptible") aborted for pending SIGKILLs when faulting non-hugetlb
memory, based on the premise of commit 462e00cc ("oom: stop
allocating user memory if TIF_MEMDIE is set"), hugetlb page faults now
terminate when the process has been oom killed.
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Greg Thelen <gthelen@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Allocating a large number of elements in atomic context could quickly
deplete memory reserves, so just disallow atomic resizing entirely.

Nothing currently uses mempool_resize() with anything other than
GFP_KERNEL, so convert existing callers to drop the gfp_mask.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Steffen Maier <maier@linux.vnet.ibm.com>	[zfcp]
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Steve French <sfrench@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If kernel panics due to oom, caused by a cgroup reaching its limit, when
'compulsory panic_on_oom' is enabled, then we will only see that the OOM
happened because of "compulsory panic_on_oom is enabled" but this doesn't
tell the difference between mempolicy and memcg.  And dumping system wide
information is plain wrong and more confusing.  This patch provides the
information of the cgroup whose limit triggerred panic
Signed-off-by: Balasubramani Vivekanandan <balasubramani_vivekanandan@mentor.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This code is dead since commit 9e645ab6 ("sched/numa: Continue PTE
scanning even if migrate rate limited") so remove it.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The arch_randomize_brk() function is used on several architectures,
even those that don't support ET_DYN ASLR. To avoid bulky extern/#define
tricks, consolidate the support under CONFIG_ARCH_HAS_ELF_RANDOMIZE for
the architectures that support it, while still handling CONFIG_COMPAT_BRK.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Hector Marco-Gisbert <hecmargi@upv.es>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: "David A. Long" <dave.long@linaro.org>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Arun Chandran <achandran@mvista.com>
Cc: Yann Droneaud <ydroneaud@opteya.com>
Cc: Min-Hua Chen <orca.chen@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Vineeth Vijayan <vvijayan@mvista.com>
Cc: Jeff Bailey <jeffbailey@google.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Behan Webster <behanw@converseincode.com>
Cc: Ismael Ripoll <iripoll@upv.es>
Cc: Jan-Simon Mller <dl9pf@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This fixes the "offset2lib" weakness in ASLR for arm, arm64, mips,
powerpc, and x86.  The problem is that if there is a leak of ASLR from
the executable (ET_DYN), it means a leak of shared library offset as
well (mmap), and vice versa.  Further details and a PoC of this attack
is available here:

  http://cybersecurity.upv.es/attacks/offset2lib/offset2lib.html

With this patch, a PIE linked executable (ET_DYN) has its own ASLR
region:

  $ ./show_mmaps_pie
  54859ccd6000-54859ccd7000 r-xp  ...  /tmp/show_mmaps_pie
  54859ced6000-54859ced7000 r--p  ...  /tmp/show_mmaps_pie
  54859ced7000-54859ced8000 rw-p  ...  /tmp/show_mmaps_pie
  7f75be764000-7f75be91f000 r-xp  ...  /lib/x86_64-linux-gnu/libc.so.6
  7f75be91f000-7f75beb1f000 ---p  ...  /lib/x86_64-linux-gnu/libc.so.6
  7f75beb1f000-7f75beb23000 r--p  ...  /lib/x86_64-linux-gnu/libc.so.6
  7f75beb23000-7f75beb25000 rw-p  ...  /lib/x86_64-linux-gnu/libc.so.6
  7f75beb25000-7f75beb2a000 rw-p  ...
  7f75beb2a000-7f75beb4d000 r-xp  ...  /lib64/ld-linux-x86-64.so.2
  7f75bed45000-7f75bed46000 rw-p  ...
  7f75bed46000-7f75bed47000 r-xp  ...
  7f75bed47000-7f75bed4c000 rw-p  ...
  7f75bed4c000-7f75bed4d000 r--p  ...  /lib64/ld-linux-x86-64.so.2
  7f75bed4d000-7f75bed4e000 rw-p  ...  /lib64/ld-linux-x86-64.so.2
  7f75bed4e000-7f75bed4f000 rw-p  ...
  7fffb3741000-7fffb3762000 rw-p  ...  [stack]
  7fffb377b000-7fffb377d000 r--p  ...  [vvar]
  7fffb377d000-7fffb377f000 r-xp  ...  [vdso]

The change is to add a call the newly created arch_mmap_rnd() into the
ELF loader for handling ET_DYN ASLR in a separate region from mmap ASLR,
as was already done on s390.  Removes CONFIG_BINFMT_ELF_RANDOMIZE_PIE,
which is no longer needed.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Hector Marco-Gisbert <hecmargi@upv.es>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: "David A. Long" <dave.long@linaro.org>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Arun Chandran <achandran@mvista.com>
Cc: Yann Droneaud <ydroneaud@opteya.com>
Cc: Min-Hua Chen <orca.chen@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Vineeth Vijayan <vvijayan@mvista.com>
Cc: Jeff Bailey <jeffbailey@google.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Behan Webster <behanw@converseincode.com>
Cc: Ismael Ripoll <iripoll@upv.es>
Cc: Jan-Simon Mller <dl9pf@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In preparation for moving ET_DYN randomization into the ELF loader (which
requires a static ELF_ET_DYN_BASE), this redefines s390's existing ET_DYN
randomization in a call to arch_mmap_rnd(). This refactoring results in
the same ET_DYN randomization on s390.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When an architecture fully supports randomizing the ELF load location,
a per-arch mmap_rnd() function is used to find a randomized mmap base.
In preparation for randomizing the location of ET_DYN binaries
separately from mmap, this renames and exports these functions as
arch_mmap_rnd(). Additionally introduces CONFIG_ARCH_HAS_ELF_RANDOMIZE
for describing this feature on architectures that support it
(which is a superset of ARCH_BINFMT_ELF_RANDOMIZE_PIE, since s390
already supports a separated ET_DYN ASLR from mmap ASLR without the
ARCH_BINFMT_ELF_RANDOMIZE_PIE logic).
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Hector Marco-Gisbert <hecmargi@upv.es>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: "David A. Long" <dave.long@linaro.org>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Arun Chandran <achandran@mvista.com>
Cc: Yann Droneaud <ydroneaud@opteya.com>
Cc: Min-Hua Chen <orca.chen@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Vineeth Vijayan <vvijayan@mvista.com>
Cc: Jeff Bailey <jeffbailey@google.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Behan Webster <behanw@converseincode.com>
Cc: Ismael Ripoll <iripoll@upv.es>
Cc: Jan-Simon Mller <dl9pf@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In preparation for splitting out ET_DYN ASLR, this refactors the use of
mmap_rnd() to be used similarly to arm and x86, and extracts the
checking of PF_RANDOMIZE.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In preparation for splitting out ET_DYN ASLR, this refactors the use of
mmap_rnd() to be used similarly to arm and x86.

(Can mmap ASLR be safely enabled in the legacy mmap case here?  Other
archs use "mm->mmap_base = TASK_UNMAPPED_BASE + random_factor".)
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In preparation for splitting out ET_DYN ASLR, extract the mmap ASLR
selection into a separate function.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In preparation for splitting out ET_DYN ASLR, this refactors the use of
mmap_rnd() to be used similarly to arm and x86.  This additionally
enables mmap ASLR on legacy mmap layouts, which appeared to be missing
on arm64, and was already supported on arm.  Additionally removes a
copy/pasted declaration of an unused function.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In preparation for splitting out ET_DYN ASLR, this refactors the use of
mmap_rnd() to be used similarly to arm, and extracts the checking of
PF_RANDOMIZE.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>