Let's not use goto when a simple if suffices. This is not error handling
code or anything, so the goto looks out of place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We used to call the entire intel specific update_plane hook while
holding struct_mutex. Actually we only need to hold struct_mutex while
pinning/unpinning the obj. The plane state itself is protected by the
kms locks, and as the object is pinned we can dig out the offset and
tiling information from it without fearing that it would change
underneath us.

So now we don't need to drop and reacquire the lock around the
wait_for_vblank. Also we will need another wait_for_vblank in the IVB
specific update_plane hook, and this way we don't need to worry about
struct_mutex there either.

Also move the intel_plane->obj=NULL assignment outside strut_mutex in
disable_plane to make it clear that it's not protected by struct_mutex.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We allow cursors to be set up when the pipe is disabled. Do the same for
sprites as well.

We need to be somewhat careful with the primary disable logic as we
don't want to accidentally enable the primary plane on a disabled pipe.

v2: Skip primary enable/disable and plane registers
    writes on disabled pipe
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

If the primary gets marked as disabled while the pipe is off for
instance, we should still re-enable it when the pipe is turned on,
unless the sprite covers it fully also in that configuration.
Unfortunately we do the plane visibility checks only in the sprite code,
which is executed after the primary enabling when turning the pipe off.

Ideally we should compute the plane visibility before touching the
hardware at all, but for now just set the primary_disabld flag
in intel_{enable,disable}_plane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

If channel equalization succeeds, there's no indication something went
wrong in clock recovery (unless debug is enabled). We should shout about
the failures and fix them instead of hiding them under the carpet.

This has allowed bugs like [1] stay dormant for a long time.

[1] https://bugs.freedesktop.org/show_bug.cgi?id=70117Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The VGACNTRL register contains a bunch of other stuff besides
the VGA_DISP_DISABLE bit. When we write the register we always set those
other bits to zero, so normally the current check would work.

However on HSW disabling and re-enabling the power well will reset the
VGACNTRL register to its default value, which has several of the other
bits set as well.

So only look at the VGA_DISP_DISABLE bit when checking whether the VGA
plane needs re-disabling.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Everyone else uses intel_PLL_is_valid(), so make VLV use it as well.

We don't have any special p and m limits on VLV, so skip those tests,
and we also need to skip the m1<=m2 test line PNV.

Reorganize the function a bit to move the n check alongside the rest of
the test for the non-derived dividers, and check the derived values
afterwards.

Note that this changes vlv_find_best_dpll() in two ways:
- The .vco comparison is now >max instead of >=max, and since we round
  down when calculating that stuff, we may now allow frequencies slightly
  above the max as we do on other platforms. The previous method
  disallowed exactly max and anything above it.
- We now check the .dot frequency against the data rate limits, which we
  didn't do before.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

If vlv_find_best_dpll() couldn't find suitable PLL settings,
just say so instead of lying to caller.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

After aligning the p1 divider limits, and removing the unused p and m
limits, intel_limits_vlv_dac and intel_limits_vlv_hdmi are identical.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We don't use .dot_limit for anything on VLV, so don't populate it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We never check the p and m limits (which according to comments are
based on someone's guesswork), so just remove them.

VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm has no p and m
limits listed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm tells us that the
minimum p2 divider is 2. Use that limit on the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

According to VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm p1
can be 2-3 always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

For some reason there's a sort of off by one issue with the p1 divider.
The actual p1 limits according to
VLV2_DPLL_mphy_hsdpll_frequency_table_ww6_rev1p1.xlsm is 2-3, so we should
just say that instead of saying 1-3 and avoiding the 1 via the choice of
comparison operator.

I don't know why we're using different p1 limits for intel_limits_vlv_dac
and intel_limits_vlv_hdmi, but let's preserve that for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We limit the maximum n divider value in order to make sure the PLL's
reference inout is at least 19.2 MHz. I assume that is done to satisfy
some hardware requirement.

However we never check whether that calculated limit is below the
maximum supoorted N divider value (7). In practice that is always true
since we only support 100 MHz reference clock, but making the code
safe against higher reference clocks seems like a reasoanble thing to
do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The p2 divider on VLV needs to be even when it's > 10. The current code
to make that happen is rather weird. Just make the step size adjustement
in the for loop decrement step.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Rewrite vlv_find_best_dpll() to use intel_clock_t rather than
an army of local variables.

Also extract the code to calculate the derived values into
vlv_clock().

v2: Split up the earlier fixes, extract vlv_clock()
v3: Initialize best_clock
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We do 'bestppm - 10' in vlv_find_best_dpll() but never check whether
that might underflow. Add such a check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Use div_u64() to make the ppm calculation in vlv_find_best_dpll() safe
against interger overflows.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The interface uses an unsigned long, and we can use the unsigned counter
throughout our code, so do so. In the process, we notice one instance
where the shrink count is based on a heuristic rather than the result,
and another where we ask for too many pages to be purged.

v2: nr_to_scan needs to be promoted to a long as well, so just use
    sc->nr_to_scan directly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Since we are waiting upon IO completion, inform the kernel through use
of the io_schedule() call rather than the regular schedule(). This
should allow the kernel to make better decisions regarding scheduling
and power management.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The conflict in intel_drv.h tripped me up a bit since a patch in dinq
moves all the functions around, but another one in drm-next removes a
single function. So I'ev figured backing this into a backmerge would
be good.

i915_dma.c is just adjacent lines changed, nothing nefarious there.

Conflicts:
	drivers/gpu/drm/i915/i915_dma.c
	drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

It's not really needed, rather just adds another place to hold
intermediate values that could go wrong, and it's not clear that the
training pattern set or training lane set should be written at this
point at all.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The user of these counters was killed in

 commit d79cdc83
 Author: Daniel Vetter <daniel.vetter@ffwll.ch>
 Date:   Thu Aug 8 15:41:32 2013 +0200

    drm: no-op out GET_STATS ioctl

so clean up the leftovers as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

We can get the PCI vendor and device IDs via dev->pdev. So we can drop
the duplicated information.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The only user of ctx_count is the via driver, and we can replace that
use with list_is_singular().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

'map_count' and 'work' are never used. Kill them both.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

irq_enabled is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm_vblank_init() is too ugly. Make it a bit easier on the eye by
collecting all the per-crtc vblank counters, timestamps etc. to
a structure and just allocate an array of those.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

vblank_enabled is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

vblank_inmodeset is a bitmask, with only two bits mind you, but better
make it unsigned anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

vblank_disable_allowed is only ever 0 or 1, so make it a bool.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

v2: duplicate intel_connector->edid, not uninitialized edid (Dave Airlie).
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm_helper_probe_single_connector_modes() can be used to implement
->fill_modes(), not ->probe().
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

If the firmware is not builtin and userspace is not yet running, we can
stall the boot process for a minute whilst the firmware loader times
out. This is contrary to expectations of providing a builtin EDID!

In the process, we can rearrange the code to make the error handling
more resilient and prevent gcc warning about unitialised variables along
the error paths.

v2: Load builtins first, fix gcc second (Jani) and cosmetics (Ville).
v3: Verify that we do not read beyond the end of the fwdata (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Analog to drm_dev_register(), we now provide drm_dev_unregister() which
does the reverse. drm_dev_put() is still in place and combines the calls
to drm_dev_unregister() and drm_dev_free() so buses don't have to change.

*_get() and *_put() are used for reference-counting in the kernel.
However, drm_dev_put() definitely does not do any kind of ref-counting.
Hence, use the more appropriate *_register(), *_unregister(), *_alloc()
and *_free() names.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>