- 25 Apr, 2016 5 commits
-
-
Bjørn Mork authored
[ Upstream commit bf13c94c ] The MC74xx and EM74xx modules use different IDs by default, according to the Lenovo EM7455 driver for Windows. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Xin Long authored
[ Upstream commit 40b4f0fd ] As the member .cmp_addr of sctp_af_inet6, sctp_v6_cmp_addr should also check the port of addresses, just like sctp_v4_cmp_addr, cause it's invoked by sctp_cmp_addr_exact(). Now sctp_v6_cmp_addr just check the port when two addresses have different family, and lack the port check for two ipv6 addresses. that will make sctp_hash_cmp() cannot work well. so fix it by adding ports comparison in sctp_v6_cmp_addr(). Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Stefan Wahren authored
[ Upstream commit a4690afe ] ether_setup sets IFF_TX_SKB_SHARING but this is not supported by qca_spi as it modifies the skb on xmit. Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06e (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by:
-
Diego Viola authored
[ Upstream commit ee50c130 ] The JMC260 network card fails to suspend/resume because the call to jme_start_irq() was too early, moving the call to jme_start_irq() after the call to jme_reset_link() makes it work. Prior this change suspend/resume would fail unless /sys/power/pm_async=0 was explicitly specified. Relevant bug report: https://bugzilla.kernel.org/show_bug.cgi?id=112351Signed-off-by:
Diego Viola <diego.viola@gmail.com> Signed-off-by:
-
Bernie Harris authored
[ Upstream commit 5146d1f1 ] IPCB may contain data from previous layers (in the observed case the qdisc layer). In the observed scenario, the data was misinterpreted as ip header options, which later caused the ihl to be set to an invalid value (<5). This resulted in an infinite loop in the mips implementation of ip_fast_csum. This patch clears IPCB(skb)->opt before dst_link_failure can be called for various types of tunnels. This change only applies to encapsulated ipv4 packets. The code introduced in 11c21a30 which clears all of IPCB has been removed to be consistent with these changes, and instead the opt field is cleared unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to SIT, GRE, and IPIP tunnels. The relevant vti, l2tp, and pptp functions already contain similar code for clearing the IPCB. Signed-off-by:
Bernie Harris <bernie.harris@alliedtelesis.co.nz> Signed-off-by:
-
- 20 Apr, 2016 1 commit
-
-
Oliver Neukum authored
commit 1666984c upstream. In case bind() works, but a later error forces bailing in probe() in error cases work and a timer may be scheduled. They must be killed. This fixes an error case related to the double free reported in http://www.spinics.net/lists/netdev/msg367669.html and needs to go on top of Linus' fix to cdc-ncm. Signed-off-by:
Oliver Neukum <ONeukum@suse.com> Signed-off-by:
-
- 15 Apr, 2016 1 commit
-
-
Kamal Mostafa authored
Signed-off-by:
-
- 12 Apr, 2016 33 commits
-
-
Sebastian Frias authored
commit 9eb13f65 upstream. This removes the dependency on GPIOLIB for non faulty PHYs. Indeed, without this patch, if GPIOLIB is not selected devm_gpiod_get_optional() will return -ENOSYS and the driver probe call will fail, regardless of the actual PHY hardware. Out of the 3 PHYs supported by this driver (AT8030, AT8031, AT8035), only AT8030 presents the issues that commit 13a56b44 ("net: phy: at803x: Add support for hardware reset") attempts to work-around by using a 'reset' GPIO line. Hence, only AT8030 should depend on GPIOLIB operating properly. Fixes: 13a56b44 ("net: phy: at803x: Add support for hardware reset") Signed-off-by:
Sebastian Frias <sf84@laposte.net> Signed-off-by:
-
Amitkumar Karwar authored
commit a6139b62 upstream. This patch corrects the error case in association path by returning -1. Earlier "media_connected" used to remain on in this error case causing failure for further association attempts. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Fixes: b887664d ('mwifiex: channel switch handling for station') Signed-off-by:
Cathy Luo <cluo@marvell.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> [ luis: backported to 3.16: - file rename: drivers/net/wireless/marvell/mwifiex/sta_ioctl.c -> drivers/net/wireless/mwifiex/sta_ioctl.c - adjusted context ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
Aaron Plattner authored
commit 2d369c74 upstream. Vendor ID 0x10de0082 is used by a yet-to-be-named GPU chip. This chip also has the 2-ch audio swapping bug, so patch_nvhdmi is appropriate here. Signed-off-by:
Aaron Plattner <aplattner@nvidia.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> [ luis: backported to 3.16: - 3.16 still uses old hda_codec_preset infrastructure ] Signed-off-by:
-
Andi Kleen authored
commit e17dc653 upstream. Jiri reported some time ago that some entries in the PEBS data source table in perf do not agree with the SDM. We investigated and the bits changed for Sandy Bridge, but the SDM was not updated. perf already implements the bits correctly for Sandy Bridge and later. This patch patches it up for Nehalem and Westmere. Signed-off-by:
Andi Kleen <ak@linux.intel.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: jolsa@kernel.org Link: http://lkml.kernel.org/r/1456871124-15985-1-git-send-email-andi@firstfloor.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> [ luis: backported to 3.16: - file rename: arch/x86/events/intel/core.c -> arch/x86/kernel/cpu/perf_event_intel.c arch/x86/events/intel/ds.c -> arch/x86/kernel/cpu/perf_event_intel_ds.c arch/x86/events/perf_event.h -> arch/x86/kernel/cpu/perf_event.h ] Signed-off-by:
-
Gabriel Krisman Bertazi authored
commit 21b81716 upstream. Commit d63c7dd5 ("ipr: Fix out-of-bounds null overwrite") removed the end of line handling when storing the update_fw sysfs attribute. This changed the userpace API because it started refusing writes terminated by a line feed, which broke the update tools we already have. This patch re-adds that handling, so both a write terminated by a line feed or not can make it through with the update. Fixes: d63c7dd5 ("ipr: Fix out-of-bounds null overwrite") Signed-off-by:
Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Cc: Insu Yun <wuninsu@gmail.com> Acked-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Insu Yun authored
commit d63c7dd5 upstream. Return value of snprintf is not bound by size value, 2nd argument. (https://www.kernel.org/doc/htmldocs/kernel-api/API-snprintf.html). Return value is number of printed chars, can be larger than 2nd argument. Therefore, it can write null byte out of bounds ofbuffer. Since snprintf puts null, it does not need to put additional null byte. Signed-off-by:
Insu Yun <wuninsu@gmail.com> Reviewed-by:
Shane Seymour <shane.seymour@hpe.com> Signed-off-by:
-
Jason Andryuk authored
commit a6807590 upstream. The comparisons should be >= since 0x800 and 0x80 require an additional bit to store. For the 3 byte case, the existing shift would drop off 2 more bits than intended. For the 2 byte case, there should be 5 bits bits in byte 1, and 6 bits in byte 2. Signed-off-by:
Jason Andryuk <jandryuk@gmail.com> Reviewed-by:
Laszlo Ersek <lersek@redhat.com> Cc: Peter Jones <pjones@redhat.com> Cc: Matthew Garrett <mjg59@coreos.com> Cc: "Lee, Chun-Yi" <jlee@suse.com> Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by:
-
Matt Fleming authored
commit e246eb56 upstream. Laszlo explains why this is a good idea, 'This is because the pstore filesystem can be backed by UEFI variables, and (for example) a crash might dump the last kilobytes of the dmesg into a number of pstore entries, each entry backed by a separate UEFI variable in the above GUID namespace, and with a variable name according to the above pattern. Please see "drivers/firmware/efi/efi-pstore.c". While this patch series will not prevent the user from deleting those UEFI variables via the pstore filesystem (i.e., deleting a pstore fs entry will continue to delete the backing UEFI variable), I think it would be nice to preserve the possibility for the sysadmin to delete Linux-created UEFI variables that carry portions of the crash log, *without* having to mount the pstore filesystem.' There's also no chance of causing machines to become bricked by deleting these variables, which is the whole purpose of excluding things from the whitelist. Use the LINUX_EFI_CRASH_GUID guid and a wildcard '*' for the match so that we don't have to update the string in the future if new variable name formats are created for crash dump variables. Reported-by:
Peter Jones <pjones@redhat.com> Tested-by:
-
Peter Jones authored
commit ed8b0de5 upstream. "rm -rf" is bricking some peoples' laptops because of variables being used to store non-reinitializable firmware driver data that's required to POST the hardware. These are 100% bugs, and they need to be fixed, but in the mean time it shouldn't be easy to *accidentally* brick machines. We have to have delete working, and picking which variables do and don't work for deletion is quite intractable, so instead make everything immutable by default (except for a whitelist), and make tools that aren't quite so broad-spectrum unset the immutable flag. Signed-off-by:
Lee, Chun-Yi <jlee@suse.com> Acked-by:
Matthew Garrett <mjg59@coreos.com> Signed-off-by:
-
Peter Jones authored
commit 8282f5d9 upstream. All the variables in this list so far are defined to be in the global namespace in the UEFI spec, so this just further ensures we're validating the variables we think we are. Including the guid for entries will become more important in future patches when we decide whether or not to allow deletion of variables based on presence in this list. Signed-off-by:
-
Peter Jones authored
commit 3dcb1f55 upstream. Actually translate from ucs2 to utf8 before doing the test, and then test against our other utf8 data, instead of fudging it. Signed-off-by:
-
Peter Jones authored
commit e0d64e6a upstream. Translate EFI's UCS-2 variable names to UTF-8 instead of just assuming all variable names fit in ASCII. Signed-off-by:
-
Peter Jones authored
commit 73500267 upstream. This adds ucs2_utf8size(), which tells us how big our ucs2 string is in bytes, and ucs2_as_utf8, which translates from ucs2 to utf8.. Signed-off-by:
-
Marcelo Tosatti authored
commit 7cae2bed upstream. As reported at https://bugs.launchpad.net/qemu/+bug/1494350, it is possible to have vcpu->arch.st.last_steal initialized from a thread other than vcpu thread, say the iothread, via KVM_SET_MSRS. Which can cause an overflow later (when subtracting from vcpu threads sched_info.run_delay). To avoid that, move steal time accumulation to vcpu entry time, before copying steal time data to guest. Signed-off-by:
Marcelo Tosatti <mtosatti@redhat.com> Reviewed-by:
David Matlack <dmatlack@google.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Cc: Liang Chen <liangchen.linux@gmail.com> Signed-off-by:
-
Thadeu Lima de Souza Cascardo authored
commit b6ee376c upstream. When creating an ip6tnl tunnel with ip tunnel, rtnl_link_ops is not set before ip6_tnl_create2 is called. When register_netdevice is called, there is no linkinfo attribute in the NEWLINK message because of that. Setting rtnl_link_ops before calling register_netdevice fixes that. Fixes: 0b112457 ("ip6tnl: add support of link creation via rtnl") Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@redhat.com> Acked-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Linus Walleij authored
commit 6ee33455 upstream. Pull up was reported as pull down and vice versa. Fix this. Fixes: 8f1774a2 "pinctrl: nomadik: improve GPIO debug prints" Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Eric Dumazet authored
commit 2d421226 upstream. IPv6 counters updates use a different macro than IPv4. Fixes: 36cbb245 ("udp: Increment UDP_MIB_IGNOREDMULTI for arriving unmatched multicasts") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Rick Jones <rick.jones2@hp.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Petri Gynther authored
commit 7dd39913 upstream. skb_len needs to be skb_headlen(skb) in bcmgenet_xmit_single(). Fragmented skbs can have only Ethernet + IP + TCP headers (14+20+20=54 bytes) in the linear buffer, followed by the rest in fragments. Bumping skb_len to ETH_ZLEN would be incorrect for this case, as it would introduce garbage between TCP header and the fragment data. This also works with regular/non-fragmented small packets < ETH_ZLEN bytes. Successfully tested this on GENETv3 with 42-byte ARP frames. For testing, I used: ethtool -K eth0 tx-checksum-ipv4 off ethtool -K eth0 tx-checksum-ipv6 off echo 0 > /proc/sys/net/ipv4/tcp_timestamps Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
Petri Gynther <pgynther@google.com> Acked-by:
-
Petri Gynther authored
commit 55868120 upstream. 1. Add bytes_compl local variable to __bcmgenet_tx_reclaim() to collect transmitted bytes. dev->stats updates can then be moved outside the while-loop. bytes_compl is also needed for future BQL support. 2. When bcmgenet device uses Tx checksum offload, each transmitted skb gets an extra 64-byte header prepended to it. Before this header is prepended to the skb, we need to save the skb "wire" length in GENET_CB(skb)->bytes_sent, so that proper Tx bytes accounting can be done in __bcmgenet_tx_reclaim(). 3. skb->len covers the entire length of skb, whether it is linear or fragmented. Thus, when we clean the fragments, do not increase transmitted bytes. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Cyrille Pitchen authored
commit ba504994 upstream. macb_interrupt() should not use macb_writel(bp, ISR, <value>) but only queue_writel(queue, ISR, <value>). There is one IRQ and one set of {ISR, IER, IDR, IMR} [1] registers per queue on gem hardware, though only queue0 is actually used for now to receive frames: other queues can already be used to transmit frames. The queue_readl() and queue_writel() helper macros are designed to access the relevant IRQ registers. [1] ISR: Interrupt Status Register IER: Interrupt Enable Register IDR: Interrupt Disable Register IMR: Interrupt Mask Register Signed-off-by:
Cyrille Pitchen <cyrille.pitchen@atmel.com> Fixes: bfbb92c4 ("net: macb: Handle the RXUBR interrupt on all devices") Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
Helge Deller authored
commit 2ef4dfd9 upstream. Handling exceptions from modules never worked on parisc. It was just masked by the fact that exceptions from modules don't happen during normal use. When a module triggers an exception in get_user() we need to load the main kernel dp value before accessing the exception_data structure, and afterwards restore the original dp value of the module on exit. Noticed-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Helge Deller authored
commit ef72f311 upstream. The kernel module testcase (lib/test_user_copy.c) exhibited a kernel crash on parisc if the parameters for copy_from_user were reversed ("illegal reversed copy_to_user" testcase). Fix this potential crash by checking the fault handler if the faulting address is in the exception table. Signed-off-by:
-
Helge Deller authored
commit e3893027 upstream. We want to avoid the kernel module loader to create function pointers for the kernel fixup routines of get_user() and put_user(). Changing the external reference from function type to int type fixes this. This unbreaks exception handling for get_user() and put_user() when called from a kernel module. Signed-off-by:
-
Yong Li authored
commit 9b8e3ec3 upstream. The current implementation only uses the first byte in val, the second byte is always 0. Change it to use cpu_to_le16 to write the two bytes into the register Signed-off-by:
Yong Li <sdliyong@gmail.com> Reviewed-by:
Phil Reid <preid@electromag.com.au> Signed-off-by:
-
Dan Williams authored
commit 21129112 upstream. It appears that smart data retrieval has been broken the since the initial implementation. Fix the payload size to be 128-bytes per the specification. Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Michael S. Tsirkin authored
commit 05dbcb43 upstream. The spec says: after writing 0 to device_status, the driver MUST wait for a read of device_status to return 0 before reinitializing the device. Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Acked-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Bjørn Mork authored
commit d48d5691 upstream. Thomas reports: "Windows: 00 diagnostics 01 modem 02 at-port 03 nmea 04 nic Linux: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2001 ProdID=7e19 Rev=02.32 S: Manufacturer=Mobile Connect S: Product=Mobile Connect S: SerialNumber=0123456789ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage" Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Martyn Welch authored
commit cddc9434 upstream. The CP2105 is used in the GE Healthcare Remote Alarm Box, with the Manufacturer ID of 0x1901 and Product ID of 0x0194. Signed-off-by:
Martyn Welch <martyn.welch@collabora.co.uk> Signed-off-by:
-
Josh Boyer authored
commit ea6db90e upstream. A Fedora user reports that the ftdi_sio driver works properly for the ICP DAS I-7561U device. Further, the user manual for these devices instructs users to load the driver and add the ids using the sysfs interface. Add support for these in the driver directly so that the devices work out of the box instead of needing manual configuration. Reported-by: <thesource@mail.ru> Signed-off-by:
Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by:
-
Filipe Manana authored
commit 56f23fdb upstream. If we rename an inode A (be it a file or a directory), create a new inode B with the old name of inode A and under the same parent directory, fsync inode B and then power fail, at log tree replay time we end up removing inode A completely. If inode A is a directory then all its files are gone too. Example scenarios where this happens: This is reproducible with the following steps, taken from a couple of test cases written for fstests which are going to be submitted upstream soon: # Scenario 1 mkfs.btrfs -f /dev/sdc mount /dev/sdc /mnt mkdir -p /mnt/a/x echo "hello" > /mnt/a/x/foo echo "world" > /mnt/a/x/bar sync mv /mnt/a/x /mnt/a/y mkdir /mnt/a/x xfs_io -c fsync /mnt/a/x <power failure happens> The next time the fs is mounted, log tree replay happens and the directory "y" does not exist nor do the files "foo" and "bar" exist anywhere (neither in "y" nor in "x", nor the root nor anywhere). # Scenario 2 mkfs.btrfs -f /dev/sdc mount /dev/sdc /mnt mkdir /mnt/a echo "hello" > /mnt/a/foo sync mv /mnt/a/foo /mnt/a/bar echo "world" > /mnt/a/foo xfs_io -c fsync /mnt/a/foo <power failure happens> The next time the fs is mounted, log tree replay happens and the file "bar" does not exists anymore. A file with the name "foo" exists and it matches the second file we created. Another related problem that does not involve file/data loss is when a new inode is created with the name of a deleted snapshot and we fsync it: mkfs.btrfs -f /dev/sdc mount /dev/sdc /mnt mkdir /mnt/testdir btrfs subvolume snapshot /mnt /mnt/testdir/snap btrfs subvolume delete /mnt/testdir/snap rmdir /mnt/testdir mkdir /mnt/testdir xfs_io -c fsync /mnt/testdir # or fsync some file inside /mnt/testdir <power failure> The next time the fs is mounted the log replay procedure fails because it attempts to delete the snapshot entry (which has dir item key type of BTRFS_ROOT_ITEM_KEY) as if it were a regular (non-root) entry, resulting in the following error that causes mount to fail: [52174.510532] BTRFS info (device dm-0): failed to delete reference to snap, inode 257 parent 257 [52174.512570] ------------[ cut here ]------------ [52174.513278] WARNING: CPU: 12 PID: 28024 at fs/btrfs/inode.c:3986 __btrfs_unlink_inode+0x178/0x351 [btrfs]() [52174.514681] BTRFS: Transaction aborted (error -2) [52174.515630] Modules linked in: btrfs dm_flakey dm_mod overlay crc32c_generic ppdev xor raid6_pq acpi_cpufreq parport_pc tpm_tis sg parport tpm evdev i2c_piix4 proc [52174.521568] CPU: 12 PID: 28024 Comm: mount Tainted: G W 4.5.0-rc6-btrfs-next-27+ #1 [52174.522805] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014 [52174.524053] 0000000000000000 ffff8801df2a7710 ffffffff81264e93 ffff8801df2a7758 [52174.524053] 0000000000000009 ffff8801df2a7748 ffffffff81051618 ffffffffa03591cd [52174.524053] 00000000fffffffe ffff88015e6e5000 ffff88016dbc3c88 ffff88016dbc3c88 [52174.524053] Call Trace: [52174.524053] [<ffffffff81264e93>] dump_stack+0x67/0x90 [52174.524053] [<ffffffff81051618>] warn_slowpath_common+0x99/0xb2 [52174.524053] [<ffffffffa03591cd>] ? __btrfs_unlink_inode+0x178/0x351 [btrfs] [52174.524053] [<ffffffff81051679>] warn_slowpath_fmt+0x48/0x50 [52174.524053] [<ffffffffa03591cd>] __btrfs_unlink_inode+0x178/0x351 [btrfs] [52174.524053] [<ffffffff8118f5e9>] ? iput+0xb0/0x284 [52174.524053] [<ffffffffa0359fe8>] btrfs_unlink_inode+0x1c/0x3d [btrfs] [52174.524053] [<ffffffffa038631e>] check_item_in_log+0x1fe/0x29b [btrfs] [52174.524053] [<ffffffffa0386522>] replay_dir_deletes+0x167/0x1cf [btrfs] [52174.524053] [<ffffffffa038739e>] fixup_inode_link_count+0x289/0x2aa [btrfs] [52174.524053] [<ffffffffa038748a>] fixup_inode_link_counts+0xcb/0x105 [btrfs] [52174.524053] [<ffffffffa038a5ec>] btrfs_recover_log_trees+0x258/0x32c [btrfs] [52174.524053] [<ffffffffa03885b2>] ? replay_one_extent+0x511/0x511 [btrfs] [52174.524053] [<ffffffffa034f288>] open_ctree+0x1dd4/0x21b9 [btrfs] [52174.524053] [<ffffffffa032b753>] btrfs_mount+0x97e/0xaed [btrfs] [52174.524053] [<ffffffff8108e1b7>] ? trace_hardirqs_on+0xd/0xf [52174.524053] [<ffffffff8117bafa>] mount_fs+0x67/0x131 [52174.524053] [<ffffffff81193003>] vfs_kern_mount+0x6c/0xde [52174.524053] [<ffffffffa032af81>] btrfs_mount+0x1ac/0xaed [btrfs] [52174.524053] [<ffffffff8108e1b7>] ? trace_hardirqs_on+0xd/0xf [52174.524053] [<ffffffff8108c262>] ? lockdep_init_map+0xb9/0x1b3 [52174.524053] [<ffffffff8117bafa>] mount_fs+0x67/0x131 [52174.524053] [<ffffffff81193003>] vfs_kern_mount+0x6c/0xde [52174.524053] [<ffffffff8119590f>] do_mount+0x8a6/0x9e8 [52174.524053] [<ffffffff811358dd>] ? strndup_user+0x3f/0x59 [52174.524053] [<ffffffff81195c65>] SyS_mount+0x77/0x9f [52174.524053] [<ffffffff814935d7>] entry_SYSCALL_64_fastpath+0x12/0x6b [52174.561288] ---[ end trace 6b53049efb1a3ea6 ]--- Fix this by forcing a transaction commit when such cases happen. This means we check in the commit root of the subvolume tree if there was any other inode with the same reference when the inode we are fsync'ing is a new inode (created in the current transaction). Test cases for fstests, covering all the scenarios given above, were submitted upstream for fstests: * fstests: generic test for fsync after renaming directory https://patchwork.kernel.org/patch/8694281/ * fstests: generic test for fsync after renaming file https://patchwork.kernel.org/patch/8694301/ * fstests: add btrfs test for fsync after snapshot deletion https://patchwork.kernel.org/patch/8670671/Signed-off-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
David Disseldorp authored
commit 2224d879 upstream. As of 5a60e876, RBD object request allocations are made via rbd_obj_request_create() with GFP_NOIO. However, subsequent OSD request allocations in rbd_osd_req_create*() use GFP_ATOMIC. With heavy page cache usage (e.g. OSDs running on same host as krbd client), rbd_osd_req_create() order-1 GFP_ATOMIC allocations have been observed to fail, where direct reclaim would have allowed GFP_NOIO allocations to succeed. Suggested-by:
Vlastimil Babka <vbabka@suse.cz> Suggested-by:
Neil Brown <neilb@suse.com> Signed-off-by:
David Disseldorp <ddiss@suse.de> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Signed-off-by:
-
Paolo Bonzini authored
commit 95272c29 upstream. -ftracer can duplicate asm blocks causing compilation to fail in noclone functions. For example, KVM declares a global variable in an asm like asm("2: ... \n .pushsection data \n .global vmx_return \n vmx_return: .long 2b"); and -ftracer causes a double declaration. Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Michal Marek <mmarek@suse.cz> Cc: kvm@vger.kernel.org Reported-by:
Linda Walsh <lkml@tlinx.org> Signed-off-by:
-
Johannes Berg authored
commit 62b14b24 upstream. The original hand-implemented hash-table in mac80211 couldn't result in insertion errors, and while converting to rhashtable I evidently forgot to check the errors. This surfaced now only because Ben is adding many identical keys and that resulted in hidden insertion errors. Fixes: 7bedd0cf ("mac80211: use rhashtable for station table") Reported-by:
Ben Greear <greearb@candelatech.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
