An error occurred fetching the project authors.
- 29 Dec, 2008 40 commits
-
-
Mauro Carvalho Chehab authored
AC97 devices provide several input and outputs. However, before this patch, em28xx device weren't properly allowing the usage of ac97 possible combinations. Also, several input volumes were left untouched, instead of making sure that the volumes were set on mute state. This patch improves support for ac97 devices by allowing to use any inputs, and making sure that unused inputs are set on mute state. Yet, some work is still needed to select the AC97 output. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
This makes easier to identify vendor ID, since AC97 vendors are generally identified by 3 bytes. The remaining byte is used by the vendor to identify its devices. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
This patch properly implements audio handling on em28xx. Before this patch, it was assumed that every device has an Empia 202 audio chip. However, this is not true. After this patch, specific AC97 chipset setup and configurations can be done. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
audio mux entries were described by 0 and 1 magic numers. Use an enum alias for each entry type. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
This patch parepares for an audio refactor patch that auto-detects ac97 chips. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Make use of the em28xx chip configuration register to determine whether we have AC97 audio, I2S audio, or no audio support at all. Thanks for Ray Lu from Empia for providing the em2860/em2880 datasheet. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
Previously, AC97 registers were named as if they were part of em28xx device, generating some confusion. Replace such names for a more general naming convention. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Julia Lawall authored
ARRAY_SIZE is more concise to use when the size of an array is divided by the size of its type or the size of its first element. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @i@ @@ @depends on i using "paren.iso"@ type T; T[] E; @@ - (sizeof(E)/sizeof(E[...])) + ARRAY_SIZE(E) @depends on i using "paren.iso"@ type T; T[] E; @@ - (sizeof(E)/sizeof(T)) + ARRAY_SIZE(E) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Harvey Harrison authored
Noticed by sparse: drivers/media/dvb/dvb-usb/af9015.c:756:25: warning: restricted __le16 degrades to integer drivers/media/dvb/dvb-usb/af9015.c:744:28: warning: restricted __le16 degrades to integer Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Harvey Harrison authored
All noticed by sparse: drivers/media/dvb/dvb-usb/cinergyT2-core.c:35:5: warning: symbol 'disable_remote' was not declared. Should it be static? drivers/media/dvb/dvb-usb/cinergyT2-core.c:48:23: warning: symbol 'cinergyt2_usb_device' was not declared. Should it be static? drivers/media/dvb/dvb-usb/cinergyT2-fe.c:160:15: warning: cast to restricted __le16 drivers/media/dvb/dvb-usb/cinergyT2-fe.c:190:9: warning: cast to restricted __le32 drivers/media/dvb/dvb-usb/cinergyT2-fe.c:208:9: warning: cast to restricted __le32 drivers/media/dvb/dvb-usb/cinergyT2-fe.c:227:24: warning: cast to restricted __le16 drivers/media/dvb/dvb-usb/cinergyT2-fe.c:275:12: warning: incorrect type in assignment (different base types) drivers/media/dvb/dvb-usb/cinergyT2-fe.c:275:12: expected unsigned short [unsigned] [assigned] [usertype] tps drivers/media/dvb/dvb-usb/cinergyT2-fe.c:275:12: got restricted __le16 [usertype] <noident> drivers/media/dvb/dvb-usb/cinergyT2-fe.c:276:13: warning: incorrect type in assignment (different base types) drivers/media/dvb/dvb-usb/cinergyT2-fe.c:276:13: expected unsigned int [unsigned] [assigned] [usertype] freq drivers/media/dvb/dvb-usb/cinergyT2-fe.c:276:13: got restricted __le32 [usertype] <noident> Cc: Thierry Merle <thierry.merle@free.fr> Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Place the s5h1411 into low power mode until first use (to handle the case where the user plugs in the device and then doesn't use it for a while). On the Pinnacle 801e, this brings the power usage from 126ma down to 82ma. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Add support for the ATI TV Wonder HD 600 USB Remote Control (required a new keymap) [mchehab@redhat.com: Fix CodingStyle] Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Refactor the em28xx IR support based on the em2860/em2880 and em2874 datasheets. Tested on the HVR-950 (em2883), Pinnacle 800e (em2883), Pinnacle 80e (em2874) using the remote controls that came with those products. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
The first em28xx were based on i2c IR's. However, some newer designs are coming with a polling-based IR. Those are done by reading a register set at em28xx. This patch adds core polling support for those devices. Later patches will add support for some device-specific IR's. This patch adds the same basic IR polling code used by bttv, cx88 and saa7134, and shares the common getkey masks defined at ir-common. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Add registration for Pinnacle 80e ATSC tuner Register the em2874 based Pinnacle 80e device. Note that support for this device also requires the new drx-j driver (which is not available yet) Thanks for Ray Lu from Empia for providing the em2874 datasheet. Thanks to Joerg Schindler from Pinnacle for providing sample hardware. Thanks to Rainer Miethling from Pinnacle for providing engineering support. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Properly support capture start on em2874 The transport stream enable register moved in the em2874, so make it work properly. Thanks for Ray Lu from Empia for providing the em2874 datasheet. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Rework the logic so that the em28xx-alsa module does not get loaded for devices that don't support analog audio (such as the em2874) Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Empia moved around their endpoint configuration in newer chips, so accommodate the changes Thanks for Ray Lu from Empia for providing the em2874 datasheet. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Fix case where we could end up dereferencing a NULL pointer if dev->vdev or dev->vbi_dev were not set properly. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Empia switched to a 16-bit addressable eeprom in newer devices. While we could certainly write a routine to read the eeprom, there is nothing of use in there that cannot be accessed through registers, and there is the risk that we could corrupt the eeprom (since a 16-bit read call is interpreted as a write call by 8-bit eeproms). So just be safe and bail out of the function. Thanks for Ray Lu from Empia for providing the em2874 datasheet. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Empia moved the location of the GPIO/GPO registers in newer devices. Add the ability to specify the relocated registers (including caching of register contents). Thanks for Ray Lu from Empia for providing the em2874 datasheet. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
When setting up the device, remember the chip id, so we can control behavior in the future without having to read the register continuously. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Add a EM28XX_NODECODER option to the list of available decoders. This option becomes important for devices that do not have analog support. Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Remove unused variable from em28xx-audio.c Fix warning for unused "ret" variable Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Add em2874 chip id Add chip id for em2874 to list of known chips Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
video_ioctl2 lacks implementation of those two ioctls: - VIDIOC_ENUM_FRAMESIZES and VIDIOC_ENUM_FRAMEINTERVALS Adds implementation for those. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Darron Broad authored
This cleans-up MFE attachment for saa-7134 dvb devices. note: MFE is not fully implemented here yet. Signed-off-by: Darron Broad <darron@kewl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Darron Broad authored
This cleans-up MFE attachment for these cards plus two cases of potential memory leak on attachment failure. Signed-off-by: Darron Broad <darron@kewl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Laurent Pinchart authored
Failed requests will now generate a one-time warning message instead of the usual "Failed to query..." error, which should be more user-friendly. The driver will also recover automatically from failed GET_MIN/GET_MAX requests when the device is half-broken without requiring the MINMAX quirk (fully broken devices still need the quirk). Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-Francois Moine authored
According to http://bugzilla.kernel.org/show_bug.cgi?id=11997, the driver sn9c102 does not work for this webcam. Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-Francois Moine authored
According to http://bugzilla.kernel.org/show_bug.cgi?id=11920, the driver sn9c102 does not work for this webcam. Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-