- 15 Jun, 2016 33 commits
-
-
Dave Gerlach authored
commit c998c078 upstream. Currently the 'registered' member of the cpuidle_device struct is set to 1 during cpuidle_register_device. In this same function there are checks to see if the device is already registered to prevent duplicate calls to register the device, but this value is never set to 0 even on unregister of the device. Because of this, any attempt to call cpuidle_register_device after a call to cpuidle_unregister_device will fail which shouldn't be the case. To prevent this, set registered to 0 when the device is unregistered. Fixes: c878a52d (cpuidle: Check if device is already registered) Signed-off-by:
Dave Gerlach <d-gerlach@ti.com> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Raghava Aditya Renukunta authored
commit fc4bf75e upstream. Typically under error conditions, it is possible for aac_command_thread() to miss the wakeup from kthread_stop() and go back to sleep, causing it to hang aac_shutdown. In the observed scenario, the adapter is not functioning correctly and so aac_fib_send() never completes (or time-outs depending on how it was called). Shortly after aac_command_thread() starts it performs aac_fib_send(SendHostTime) which hangs. When aac_probe_one /aac_get_adapter_info send time outs, kthread_stop is called which breaks the command thread out of it's hang. The code will still go back to sleep in schedule_timeout() without checking kthread_should_stop() so it causes aac_probe_one to hang until the schedule_timeout() which is 30 minutes. Fixed by: Adding another kthread_should_stop() before schedule_timeout() Signed-off-by:
Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit 07beca2b upstream. aac_fib_send has a special function case for initial commands during driver initialization using wait < 0(pseudo sync mode). In this case, the command does not sleep but rather spins checking for timeout.This loop is calls cpu_relax() in an attempt to allow other processes/threads to use the CPU, but this function does not relinquish the CPU and so the command will hog the processor. This was observed in a KDUMP "crashkernel" and that prevented the "command thread" (which is responsible for completing the command from being timed out) from starting because it could not get the CPU. Fixed by replacing "cpu_relax()" call with "schedule()" Signed-off-by:
-
Joseph Salisbury authored
commit 7b9bc799 upstream. BugLink: http://bugs.launchpad.net/bugs/972604 Commit 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") added a pin configuration for the Compaq c700 laptop. However, the polarity of the led pin is reversed. It should be red for wifi off and blue for wifi on, but it is the opposite. This bug was reported in the following bug report: http://pad.lv/972604 Fixes: 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Ricky Liang authored
commit affa80bd upstream. When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS ioctl needs to be treated with special care, as it has the pointer size encoded in the command. Signed-off-by:
Ricky Liang <jcliang@chromium.org> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Matthias Schiffer authored
commit f5b556c9 upstream. This makes the ath79 bootconsole behave the same way as the generic 8250 bootconsole. Also waiting for TEMT (transmit buffer is empty) instead of just THRE (transmit buffer is not full) ensures that all characters have been transmitted before the real serial driver starts reconfiguring the serial controller (which would sometimes result in garbage being transmitted.) This change does not cause a visible performance loss. In addition, this seems to fix a hang observed in certain configurations on many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver. A more complete follow-up patch will disable 8250 autoconfig for ath79 altogether (the serial controller is detected as a 16550A, which is not fully compatible with the ath79 serial, and the autoconfig may lead to undefined behavior on ath79.) Signed-off-by:
Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
James Hogan authored
commit 5daebc47 upstream. Commit 85efde6f ("make exported headers use strict posix types") changed the asm-generic siginfo.h to use the __kernel_* types, and commit 3a471cbc ("remove __KERNEL_STRICT_NAMES") make the internal types accessible only to the kernel, but the MIPS implementation hasn't been updated to match. Switch to proper types now so that the exported asm/siginfo.h won't produce quite so many compiler errors when included alone by a user program. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Christopher Ferris <cferris@google.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/12477/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Paul Burton authored
commit ab4a92e6 upstream. When emulating a jalr instruction with rd == $0, the code in isBranchInstr was incorrectly writing to GPR $0 which should actually always remain zeroed. This would lead to any further instructions emulated which use $0 operating on a bogus value until the task is next context switched, at which point the value of $0 in the task context would be restored to the correct zero by a store in SAVE_SOME. Fix this by not writing to rd if it is $0. Fixes: 102cedc3 ("MIPS: microMIPS: Floating point support.") Signed-off-by:
Paul Burton <paul.burton@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13160/Signed-off-by:
-
Chanwoo Choi authored
commit b8995f52 upstream. This patch fixes the broken serial log when changing the clock source of uart device. Before disabling the original clock source, this patch enables the new clock source to protect the clock off state for a split second. Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
-
Jiri Slaby authored
commit 6798df4c upstream. When csw->con_startup() fails in do_register_con_driver, we return no error (i.e. 0). This was changed back in 2006 by commit 3e795de7. Before that we used to return -ENODEV. So fix the return value to be -ENODEV in that case again. Fixes: 3e795de7 ("VT binding: Add binding/unbinding support for the VT console") Signed-off-by:
"Dan Carpenter" <dan.carpenter@oracle.com> Signed-off-by:
-
Schemmel Hans-Christoph authored
commit 444f94e9 upstream. Added support for Gemalto's Cinterion PH8 and AHxx products with 2 RmNet Interfaces and products with 1 RmNet + 1 USB Audio interface. In addition some minor renaming and formatting. Signed-off-by:
Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com> [johan: sort current entries and trim trailing whitespace ] Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit c8d62957 upstream. URBs and buffers allocated in attach for Epic devices would never be deallocated in case of a later probe error (e.g. failure to allocate minor numbers) as disconnect is then never called. Fix by moving deallocation to release and making sure that the URBs are first unlinked. Fixes: f9c99bb8 ("USB: usb-serial: replace shutdown with disconnect, release") Signed-off-by:
-
Johan Hovold authored
commit c5c0c555 upstream. Private data, URBs and buffers allocated for Epic devices during attach were never released on errors (e.g. missing endpoints). Fixes: 6e8cf775 ("USB: add EPIC support to the io_edgeport driver") Signed-off-by:
-
Johan Hovold authored
commit 028c49f5 upstream. The interface read URB is submitted in attach, but was only unlinked by the driver at disconnect. In case of a late probe error (e.g. due to failed minor allocation), disconnect is never called and we would end up with active URBs for an unbound interface. This in turn could lead to deallocated memory being dereferenced in the completion callback. Fixes: f7a33e60 ("USB: serial: add quatech2 usb to serial driver") Signed-off-by:
-
Johan Hovold authored
commit 35be1a71 upstream. The interface instat and indat URBs were submitted in attach, but never unlinked in release before deallocating the corresponding transfer buffers. In the case of a late probe error (e.g. due to failed minor allocation), disconnect would not have been called before release, causing the buffers to be freed while the URBs are still in use. We'd also end up with active URBs for an unbound interface. Fixes: f9c99bb8 ("USB: usb-serial: replace shutdown with disconnect, release") Signed-off-by:
-
Vladis Dronov authored
commit d5468d7a upstream. Commit 588afcc1 ("[media] usbvision fix overflow of interfaces array")' should be reverted, because: * "!dev->actconfig->interface[ifnum]" won't catch a case where the value is not NULL but some garbage. This way the system may crash later with GPF. * "(ifnum >= USB_MAXINTERFACES)" does not cover all the error conditions. "ifnum" should be compared to "dev->actconfig-> desc.bNumInterfaces", i.e. compared to the number of "struct usb_interface" kzalloc()-ed, not to USB_MAXINTERFACES. * There is a "struct usb_device" leak in this error path, as there is usb_get_dev(), but no usb_put_dev() on this path. * There is a bug of the same type several lines below with number of endpoints. The code is accessing hard-coded second endpoint ("interface->endpoint[1].desc") which may not exist. It would be great to handle this in the same patch too. * All the concerns above are resolved by already-accepted commit fa52bd50 ("[media] usbvision: fix crash on detecting device with invalid configuration") * Mailing list message: http://www.spinics.net/lists/linux-media/msg94832.htmlSigned-off-by:
Vladis Dronov <vdronov@redhat.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Matt Gumbel authored
commit 32ecd320 upstream. 008GE0 Toshiba mmc in some Intel Baytrail tablets responds to MMC_SEND_EXT_CSD in 450-600ms. This patch will... () Increase the long read time quirk timeout from 300ms to 600ms. Original author of that quirk says 300ms was only a guess and that the number may need to be raised in the future. () Add this specific MMC to the quirk Signed-off-by:
Matt Gumbel <matthew.k.gumbel@intel.com> Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Lv Zheng authored
commit 30c9bb0d upstream. The order of the _OSI related functionalities is as follows: acpi_blacklisted() acpi_dmi_osi_linux() acpi_osi_setup() acpi_osi_setup() acpi_update_interfaces() if "!*" <<<<<<<<<<<<<<<<<<<<<<<< parse_args() __setup("acpi_osi=") acpi_osi_setup_linux() acpi_update_interfaces() if "!*" <<<<<<<<<<<<<<<<<<<<<<<< acpi_early_init() acpi_initialize_subsystem() acpi_ut_initialize_interfaces() ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ acpi_bus_init() acpi_os_initialize1() acpi_install_interface_handler(acpi_osi_handler) acpi_osi_setup_late() acpi_update_interfaces() for "!" >>>>>>>>>>>>>>>>>>>>>>>> acpi_osi_handler() Since acpi_osi_setup_linux() can override acpi_dmi_osi_linux(), the command line setting can override the DMI detection. That's why acpi_blacklisted() is put before __setup("acpi_osi="). Then we can notice the following wrong invocation order. There are acpi_update_interfaces() (marked by <<<<) calls invoked before acpi_ut_initialize_interfaces() (marked by ^^^^). This makes it impossible to use acpi_osi=!* correctly from OSI DMI table or from the command line. The use of acpi_osi=!* is meant to disable both ACPICA (acpi_gbl_supported_interfaces) and Linux specific strings (osi_setup_entries) while the ACPICA part should have stopped working because of the order issue. This patch fixes this issue by moving acpi_update_interfaces() to where it is invoked for acpi_osi=! (marked by >>>>) as this is ensured to be invoked after acpi_ut_initialize_interfaces() (marked by ^^^^). Linux specific strings are still handled in the original place in order to make the following command line working: acpi_osi=!* acpi_osi="Module Device". Note that since acpi_osi=!* is meant to further disable linux specific string comparing to the acpi_osi=!, there is no such use case in our bug fixing work and hence there is no one using acpi_osi=!* either from the command line or from the DMI quirks, this issue is just a theoretical issue. Fixes: 741d8128 (ACPI: Add facility to remove all _OSI strings) Tested-by:
Lukas Wunner <lukas@wunner.de> Tested-by:
Chen Yu <yu.c.chen@intel.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Signed-off-by:
-
Adrian Hunter authored
commit 1c447116 upstream. Some eMMCs set the partition switch timeout too low. Now typically eMMCs are considered a critical component (e.g. because they store the root file system) and consequently are expected to be reliable. Thus we can neglect the use case where eMMCs can't switch reliably and we might want a lower timeout to facilitate speedy recovery. Although we could employ a quirk for the cards that are affected (if we could identify them all), as described above, there is little benefit to having a low timeout, so instead simply set a minimum timeout. The minimum is set to 300ms somewhat arbitrarily - the examples that have been seen had a timeout of 10ms but were sometimes taking 60-70ms. Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 59643d15 upstream. If the size passed to ring_buffer_resize() is greater than MAX_LONG - BUF_PAGE_SIZE then the DIV_ROUND_UP() will return zero. Here's the details: # echo 18014398509481980 > /sys/kernel/debug/tracing/buffer_size_kb tracing_entries_write() processes this and converts kb to bytes. 18014398509481980 << 10 = 18446744073709547520 and this is passed to ring_buffer_resize() as unsigned long size. size = DIV_ROUND_UP(size, BUF_PAGE_SIZE); Where DIV_ROUND_UP(a, b) is (a + b - 1)/b BUF_PAGE_SIZE is 4080 and here 18446744073709547520 + 4080 - 1 = 18446744073709551599 where 18446744073709551599 is still smaller than 2^64 2^64 - 18446744073709551599 = 17 But now 18446744073709551599 / 4080 = 4521260802379792 and size = size * 4080 = 18446744073709551360 This is checked to make sure its still greater than 2 * 4080, which it is. Then we convert to the number of buffer pages needed. nr_page = DIV_ROUND_UP(size, BUF_PAGE_SIZE) but this time size is 18446744073709551360 and 2^64 - (18446744073709551360 + 4080 - 1) = -3823 Thus it overflows and the resulting number is less than 4080, which makes 3823 / 4080 = 0 an nr_pages is set to this. As we already checked against the minimum that nr_pages may be, this causes the logic to fail as well, and we crash the kernel. There's no reason to have the two DIV_ROUND_UP() (that's just result of historical code changes), clean up the code and fix this bug. Fixes: 83f40318 ("ring-buffer: Make removal of ring buffer pages atomic") Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 9b94a8fb upstream. The size variable to change the ring buffer in ftrace is a long. The nr_pages used to update the ring buffer based on the size is int. On 64 bit machines this can cause an overflow problem. For example, the following will cause the ring buffer to crash: # cd /sys/kernel/debug/tracing # echo 10 > buffer_size_kb # echo 8556384240 > buffer_size_kb Then you get the warning of: WARNING: CPU: 1 PID: 318 at kernel/trace/ring_buffer.c:1527 rb_update_pages+0x22f/0x260 Which is: RB_WARN_ON(cpu_buffer, nr_removed); Note each ring buffer page holds 4080 bytes. This is because: 1) 10 causes the ring buffer to have 3 pages. (10kb requires 3 * 4080 pages to hold) 2) (2^31 / 2^10 + 1) * 4080 = 8556384240 The value written into buffer_size_kb is shifted by 10 and then passed to ring_buffer_resize(). 8556384240 * 2^10 = 8761737461760 3) The size passed to ring_buffer_resize() is then divided by BUF_PAGE_SIZE which is 4080. 8761737461760 / 4080 = 2147484672 4) nr_pages is subtracted from the current nr_pages (3) and we get: 2147484669. This value is saved in a signed integer nr_pages_to_update 5) 2147484669 is greater than 2^31 but smaller than 2^32, a signed int turns into the value of -2147482627 6) As the value is a negative number, in update_pages_handler() it is negated and passed to rb_remove_pages() and 2147482627 pages will be removed, which is much larger than 3 and it causes the warning because not all the pages asked to be removed were removed. Link: https://bugzilla.kernel.org/show_bug.cgi?id=118001 Fixes: 7a8e76a3 ("tracing: unified trace buffer") Reported-by:
Hao Qin <QEver.cn@gmail.com> Signed-off-by:
-
Stefan Metzmacher authored
commit cfda35d9 upstream. See [MS-NLMP] 3.2.5.1.2 Server Receives an AUTHENTICATE_MESSAGE from the Client: ... Set NullSession to FALSE If (AUTHENTICATE_MESSAGE.UserNameLen == 0 AND AUTHENTICATE_MESSAGE.NtChallengeResponse.Length == 0 AND (AUTHENTICATE_MESSAGE.LmChallengeResponse == Z(1) OR AUTHENTICATE_MESSAGE.LmChallengeResponse.Length == 0)) -- Special case: client requested anonymous authentication Set NullSession to TRUE ... Only server which map unknown users to guest will allow access using a non-null NTChallengeResponse. For Samba it's the "map to guest = bad user" option. BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913Signed-off-by:
Stefan Metzmacher <metze@samba.org> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Steve French authored
commit 897fba11 upstream. Wrong return code was being returned on SMB3 rmdir of non-empty directory. For SMB3 (unlike for cifs), we attempt to delete a directory by set of delete on close flag on the open. Windows clients set this flag via a set info (SET_FILE_DISPOSITION to set this flag) which properly checks if the directory is empty. With this patch on smb3 mounts we correctly return "DIRECTORY NOT EMPTY" on attempts to remove a non-empty directory. Signed-off-by:
Steve French <steve.french@primarydata.com> Acked-by:
Sachin Prabhu <sprabhu@redhat.com> Signed-off-by:
-
Vineet Gupta authored
commit a6416f57 upstream. ARCompact and ARCv2 only have ASL, while binutils used to support LSL as a alias mnemonic. Newer binutils (upstream) don't want to do that so replace it. Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Daniel Bristot de Oliveira authored
commit c14022bf upstream. The device which identifies itself as a "USB Keykoard" (no typo) with VID:PID 1a2c:0027 does not seem to be handling the reports initialization very well. This results in a "usb_submit_urb(ctrl) failed: -1" message from the kernel when connected, and a delay before its initialization. It can also cause the hang the system. This patch adds the quirk for this device, which causes the delay to disappear. It is named as "USB Keykoard2" because the "USB Keykoard" already exists. Signed-off-by:
Daniel Bristot de Oliveira <bristot@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by:
-
Cyan Ogilvie authored
commit d3059673 upstream. The wiimote motion plus gyros use two scales to report fast and slow rotation - below 440 deg/s uses 8192/440 units / deg/s, and above uses 8192/2000 units / deg/s. Previously this driver attempted to linearize the two by scaling the fast rate by 18 and the slow by 9, but this results in a scale of 8192*9/440 = ~167.564 for slow and 8192*18/2000 = 73.728 for fast. Correct the fast motion scale factor so that both report ~167.564 units / deg/s Signed-off-by:
Cyan Ogilvie <cyan.ogilvie@gmail.com> Reviewed-by:
David Herrmann <dh.herrmann@gmail.com> Signed-off-by:
-
Sean Young authored
commit 6e5e9a06 upstream. This device supports force feedback and has two ports. Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Николай Кудрявцев authored
commit 9a1d78a3 upstream. Acer Aspire Switch 12 keyboard Chicony's controller reports too big usage index on the 1st interface. The patch fixes the report. The work based on solution from drivers/hid/hid-holtek-mouse.c Bug report: https://bugzilla.kernel.org/show_bug.cgi?id=101721Signed-off-by:
Nicholas Kudriavtsev <nkudriavtsev@gmail.com> Signed-off-by:
Jiri Kosina <jkosina@suse.com> Signed-off-by:
-
Slava Bacherikov authored
commit f9a82c20 upstream. Microsoft Wireless Comfort Keyboard has vendor specific My Favorites 1-5 keys. Linux already supports this buttons on other MS keyboards by MS_ERGONOMY quirk. So apply MS_ERGONOMY quirk to USB PID 0x00e3 (Microsoft Wireless Optical Desktop Receiver 3.0A). After this My Favorites 1..5 keys will be reported as KEY_F14..KEY_F15 events. Signed-off-by:
Slava Bacherikov <slava@bacher09.org> Signed-off-by:
-
Donavan Lance authored
commit c6956eb7 upstream. Adds support for Microsoft Type Cover 3 with 0x07e2 product ID. Signed-off-by:
Donavan Lance <shvr@fedoraproject.org> Signed-off-by:
-
Alistair Leslie-Hughes authored
commit c847a89a upstream. Adds support for the Micrsift Digital 4K, Media 600 and Media 3000 V1 Keyboards, which have the same quirks as the already existing hardware MS_NE4K. Fixes https://bugzilla.kernel.org/show_bug.cgi?id=52841 [jkosina@suse.cz: rephrase changelog] Signed-off-by:
Alistair Leslie-Hughes <leslie_alistair@hotmail.com> Signed-off-by:
-
Stephen Just authored
commit 0439de75 upstream. Adding support for the Microsoft Surface 3 (non-pro) Type Cover. The existing definitions and quirks are actually for the Surface Pro 3 type covers. I've renamed the old constants to reflect that they belong to the Surface Pro 3, and added a new constant and matching code for the Surface 3. Signed-off-by:
Stephen Just <stephenjust@gmail.com> Signed-off-by:
-
Raimund Roth authored
commit 18eec2cd upstream. Adding support for the Microsoft Surface Pro Power Cover. Signed-off-by:
Raimund Roth <raimundmroth@gmail.com> Signed-off-by:
-
- 31 May, 2016 3 commits
-
-
Nazar Mokrynskyi authored
commit 567a44ec upstream. Needed for v2 of the device firmware, otherwise kernel will stuck for few seconds and throw "usb_submit_urb(ctrl) failed: -1" early on system boot. Signed-off-by:
Nazar Mokrynskyi <nazar@mokrynskyi.com> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
-
Trent Lloyd authored
commit 282bf1fe upstream. These devices feature multiple interfaces/endpoints: a legacy BIOS/boot interface (endpoint 0x81), as well as 2 corsair-specific keyboard interfaces (endpoint 0x82, 0x83 IN/0x03 OUT) and an RGB LED control interface (endpoint 0x84 IN/0x04 OUT) Because the extra 3 interfaces are not of subclass USB_INTERFACE_SUBCLASS_BOOT, HID_QUIRK_NOGET is not automatically set on them and a 10s timeout per-endpoint (30s per device) occurs initialising reports on boot. We configure HID_QUIRK_NO_INIT_REPORTS for these devices. Additionally the left-side G1-G18 macro keys on the K95RGB generate output on the un-opened 0x82/0x83 endpoints which causes the keyboard to stop responding waiting for this event to be collected. We enable HID_QUIRK_ALWAYS_POLL to prevent this situation from occurring. Signed-off-by:
Trent Lloyd <trent@lloyd.id.au> Tested-by:
SUGNIAUX Wilfried <wsu@ppharm2k20.net> Signed-off-by:
-
Jason Gunthorpe authored
commit e6bd18f5 upstream. The drivers/infiniband stack uses write() as a replacement for bi-directional ioctl(). This is not safe. There are ways to trigger write calls that result in the return structure that is normally written to user space being shunted off to user specified kernel memory instead. For the immediate repair, detect and deny suspicious accesses to the write API. For long term, update the user space libraries and the kernel API to something that doesn't present the same security vulnerabilities (likely a structured ioctl() interface). The impacted uAPI interfaces are generally only available if hardware from drivers/infiniband is installed in the system. [js] backport to 3.12: hfi1 is not there yet (exclude), ipath is still there (include) Reported-by:
Jann Horn <jann@thejh.net> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> [ Expanded check to all known write() entry points ] Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
- 25 May, 2016 1 commit
-
-
Benjamin Coddington authored
commit ce85cfbe upstream. If a READDIR reply comes back without any page data, avoid a NULL pointer dereference in xdr_copy_to_scratch(). BUG: unable to handle kernel NULL pointer dereference at 0000000000000001 IP: [<ffffffff813a378d>] memcpy+0xd/0x110 ... Call Trace: ? xdr_inline_decode+0x7a/0xb0 [sunrpc] nfs3_decode_dirent+0x73/0x320 [nfsv3] nfs_readdir_page_filler+0xd5/0x4e0 [nfs] ? nfs3_rpc_wrapper.constprop.9+0x42/0xc0 [nfsv3] nfs_readdir_xdr_to_array+0x1fa/0x330 [nfs] ? mem_cgroup_commit_charge+0xac/0x160 ? nfs_readdir_xdr_to_array+0x330/0x330 [nfs] nfs_readdir_filler+0x22/0x90 [nfs] do_read_cache_page+0x7e/0x1a0 read_cache_page+0x1c/0x20 nfs_readdir+0x18e/0x660 [nfs] ? nfs3_xdr_dec_getattr3res+0x80/0x80 [nfsv3] iterate_dir+0x97/0x130 SyS_getdents+0x94/0x120 ? fillonedir+0xd0/0xd0 system_call_fastpath+0x12/0x17 Signed-off-by:
Benjamin Coddington <bcodding@redhat.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Cc: Neil Brown <nfbrown@suse.com> Signed-off-by:
-
- 19 May, 2016 3 commits
-
-
Jiri Slaby authored
-
Antonio Alecrim Jr authored
commit eb8948a0 upstream. Signed-off-by:
Antonio Alecrim Jr <antonio.alecrim@gmail.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Kirill Tkhai authored
commit f7b8a47d upstream. sched_move_task() is the only interface to change sched_task_group: cpu_cgrp_subsys methods and autogroup_move_group() use it. Everything is synchronized by task_rq_lock(), so cpu_cgroup_attach() is ordered with other users of sched_move_task(). This means we do no need RCU here: if we've dereferenced a tg here, the .attach method hasn't been called for it yet. Thus, we should pass "true" to task_css_check() to silence lockdep warnings. Fixes: eeb61e53 ("sched: Fix race between task_group and sched_task_group") Reported-by:
Oleg Nesterov <oleg@redhat.com> Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
Kirill Tkhai <ktkhai@parallels.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/1414473874.8574.2.camel@tkhaiSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
