- 23 Sep, 2020 16 commits
-
-
J. Bruce Fields authored
[ Upstream commit 8c6b6c79 ] Since p points at raw xdr data, there's no guarantee that it's NULL terminated, so we should give a length. And probably escape any special characters too. Reported-by:
Zhi Li <yieli@redhat.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Chuck Lever authored
[ Upstream commit 644c9f40 ] If a write delegation isn't available, the Linux NFS client uses a zero-stateid when performing a SETATTR. NFSv4.0 provides no mechanism for an NFS server to match such a request to a particular client. It recalls all delegations for that file, even delegations held by the client issuing the request. If that client happens to hold a read delegation, the server will recall it immediately, resulting in an NFS4ERR_DELAY/CB_RECALL/ DELEGRETURN sequence. Optimize out this pipeline bubble by having the client return any delegations it may hold on a file before it issues a SETATTR(zero-stateid) on that file. Signed-off-by:
Chuck Lever <chuck.lever@oracle.com> Signed-off-by:
-
Vincent Whitchurch authored
[ Upstream commit 837ba18d ] The "tx/rx-transfer - crossing PAGE_SIZE" test always fails when len=131071 and rx_offset >= 5: spi-loopback-test spi0.0: Running test tx/rx-transfer - crossing PAGE_SIZE ... with iteration values: len = 131071, tx_off = 0, rx_off = 3 with iteration values: len = 131071, tx_off = 0, rx_off = 4 with iteration values: len = 131071, tx_off = 0, rx_off = 5 loopback strangeness - rx changed outside of allowed range at: ...a4321000 spi_msg@ffffffd5a4157690 frame_length: 131071 actual_length: 131071 spi_transfer@ffffffd5a41576f8 len: 131071 tx_buf: ffffffd5a4340ffc Note that rx_offset > 3 can only occur if the SPI controller driver sets ->dma_alignment to a higher value than 4, so most SPI controller drivers are not affect. The allocated Rx buffer is of size SPI_TEST_MAX_SIZE_PLUS, which is 132 KiB (assuming 4 KiB pages). This test uses an initial offset into the rx_buf of PAGE_SIZE - 4, and a len of 131071, so the range expected to be written in this transfer ends at (4096 - 4) + 5 + 131071 == 132 KiB, which is also the end of the allocated buffer. But the code which verifies the content of the buffer reads a byte beyond the allocated buffer and spuriously fails because this out-of-bounds read doesn't return the expected value. Fix this by using ITERATE_LEN instead of ITERATE_MAX_LEN to avoid testing sizes which cause out-of-bounds reads. Signed-off-by:
Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20200902132341.7079-1-vincent.whitchurch@axis.comSigned-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Vincent Whitchurch authored
[ Upstream commit 59ae97a7 ] If the zero duty cycle doesn't correspond to any voltage in the voltage table, the PWM regulator returns an -EINVAL from get_voltage_sel() which results in the core erroring out with a "failed to get the current voltage" and ending up not applying the machine constraints. Instead, return -ENOTRECOVERABLE which makes the core set the voltage since it's at an unknown value. For example, with this device tree: fooregulator { compatible = "pwm-regulator"; pwms = <&foopwm 0 100000>; regulator-min-microvolt = <2250000>; regulator-max-microvolt = <2250000>; regulator-name = "fooregulator"; regulator-always-on; regulator-boot-on; voltage-table = <2250000 30>; }; Before this patch: fooregulator: failed to get the current voltage(-22) After this patch: fooregulator: Setting 2250000-2250000uV fooregulator: 2250 mV Signed-off-by:
-
James Smart authored
[ Upstream commit 7b08e89f ] The driver is unable to successfully login with remote device. During pt2pt login, the driver completes its FLOGI request with the remote device having WWN precedence. The remote device issues its own (delayed) FLOGI after accepting the driver's and, upon transmitting the FLOGI, immediately recognizes it has already processed the driver's FLOGI thus it transitions to sending a PLOGI before waiting for an ACC to its FLOGI. In the driver, the FLOGI is received and an ACC sent, followed by the PLOGI being received and an ACC sent. The issue is that the PLOGI reception occurs before the response from the adapter from the FLOGI ACC is received. Processing of the PLOGI sets state flags to perform the REG_RPI mailbox command and proceed with the rest of discovery on the port. The same completion routine used by both FLOGI and PLOGI is generic in nature. One of the things it does is clear flags, and those flags happen to drive the rest of discovery. So what happened was the PLOGI processing set the flags, the FLOGI ACC completion cleared them, thus when the PLOGI ACC completes it doesn't see the flags and stops. Fix by modifying the generic completion routine to not clear the rest of discovery flag (NLP_ACC_REGLOGIN) unless the completion is also associated with performing a mailbox command as part of its handling. For things such as FLOGI ACC, there isn't a subsequent action to perform with the adapter, thus there is no mailbox cmd ptr. PLOGI ACC though will perform REG_RPI upon completion, thus there is a mailbox cmd ptr. Link: https://lore.kernel.org/r/20200828175332.130300-3-james.smart@broadcom.comCo-developed-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Javed Hasan authored
[ Upstream commit 5a5b80f9 ] Fix for '&fp->skb' double free. Link: https://lore.kernel.org/r/20200825093940.19612-1-jhasan@marvell.comReported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Javed Hasan <jhasan@marvell.com> Signed-off-by:
-
Dinghao Liu authored
[ Upstream commit ea403fde ] When pm8001_tag_alloc() fails, task should be freed just like it is done in the subsequent error paths. Link: https://lore.kernel.org/r/20200823091453.4782-1-dinghao.liu@zju.edu.cnAcked-by:
Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by:
Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by:
-
Olga Kornievskaia authored
[ Upstream commit 3d7a9520 ] A client should be able to handle getting an ERR_DELAY error while doing a LOCK call to reclaim state due to delegation being recalled. This is a transient error that can happen due to server moving its volumes and invalidating its file location cache and upon reference to it during the LOCK call needing to do an expensive lookup (leading to an ERR_DELAY error on a PUTFH). Signed-off-by:
Olga Kornievskaia <kolga@netapp.com> Signed-off-by:
-
Haiyang Zhang authored
commit 4d820543 upstream. When using vf_ops->ndo_select_queue, the number of queues of VF is usually bigger than the synthetic NIC. This condition may happen often. Remove "unlikely" from the comparison of ndev->real_num_tx_queues. Fixes: b3bf5666 ("hv_netvsc: defer queue selection to VF") Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Miaohe Lin authored
commit eabe8618 upstream. pskb_carve_frag_list() may return -ENOMEM in pskb_carve_inside_nonlinear(). we should handle this correctly or we would get wrong sk_buff. Fixes: 6fa01ccd ("skbuff: Add pskb_extract() helper function") Signed-off-by:
Miaohe Lin <linmiaohe@huawei.com> Signed-off-by:
-
Naresh Kumar PBS authored
commit 847b9788 upstream. Some adapters report more than 256 gid entries. Restrict it to 256 for now. Fixes: 1ac5a404("RDMA/bnxt_re: Add bnxt_re RoCE driver") Link: https://lore.kernel.org/r/1598292876-26529-6-git-send-email-selvin.xavier@broadcom.comSigned-off-by:
Naresh Kumar PBS <nareshkumar.pbs@broadcom.com> Signed-off-by:
Selvin Xavier <selvin.xavier@broadcom.com> Signed-off-by:
Jason Gunthorpe <jgg@nvidia.com> Signed-off-by:
-
Bob Peterson authored
commit cbcc89b6 upstream. Since transactions may be freed shortly after they're created, before a log_flush occurs, we need to initialize their ail1 and ail2 lists earlier. Before this patch, the ail1 list was initialized in gfs2_log_flush(). This moves the initialization to the point when the transaction is first created. Signed-off-by:
Bob Peterson <rpeterso@redhat.com> Signed-off-by:
Andreas Gruenbacher <agruenba@redhat.com> Cc: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by:
-
Quinn Tran authored
commit 0aca7784 upstream. - Reduce sess_lock holding to prevent CPU Lock up. sess_lock was held across fc_port registration and deletion. These calls can be blocked by upper layer. Sess_lock is also being accessed by interrupt thread. - Reduce number of loops in processing work_list to prevent kernel complaint of CPU lockup or holding sess_lock. Reported-by:
Zhengyuan Liu <liuzhengyuan@kylinos.cn> Tested-by:
Quinn Tran <quinn.tran@cavium.com> Signed-off-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
-
Quinn Tran authored
commit cd4ed6b4 upstream. Currently, the rport registration is being called from a single work element that is used to process QLA internal "work_list". This work_list is meant for quick and simple task (ie no sleep). The Rport registration process sometime can be delayed by upper layer. This causes back pressure with the internal queue where other jobs are unable to move forward. This patch will schedule the registration process with a new work element (fc_port.reg_work). While the RPort is being registered, the current state of the fcport will not move forward until the registration is done. If the state of the fabric has changed, a new field/next_disc_state will record the next action on whether to 'DELETE' or 'Reverify the session/ADISC'. Signed-off-by:
-
Quinn Tran authored
commit cb873ba4 upstream. Rename rscn_rcvd field to scan_needed to be more meaningful. Signed-off-by:
-
Daniel Mack authored
commit 1ed9ec9b upstream. The driver for Marvell switches puts all ports in IGMP snooping mode which results in all IGMP/MLD frames that ingress on the ports to be forwarded to the CPU only. The bridge code in the kernel can then interpret these frames and act upon them, for instance by updating the mdb in the switch to reflect multicast memberships of stations connected to the ports. However, the IGMP/MLD frames must then also be forwarded to other ports of the bridge so external IGMP queriers can track membership reports, and external multicast clients can receive query reports from foreign IGMP queriers. Currently, this is impossible as the EDSA tagger sets offload_fwd_mark on the skb when it unwraps the tagged frames, and that will make the switchdev layer prevent the skb from egressing on any other port of the same switch. To fix that, look at the To_CPU code in the DSA header and make forwarding of the frame possible for trapped IGMP packets. Introduce some #defines for the frame types to make the code a bit more comprehensive. This was tested on a Marvell 88E6352 variant. Signed-off-by:
Daniel Mack <daniel@zonque.org> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Tested-by:
-
- 17 Sep, 2020 24 commits
-
-
Greg Kroah-Hartman authored
Tested-by:
Shuah Khan <skhan@linuxfoundation.org> Tested-by:
Jon Hunter <jonathanh@nvidia.com> Tested-by:
Linux Kernel Functional Testing <lkft@linaro.org> Tested-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Peter Oberparleiter authored
[ Upstream commit 40249c69 ] Using gcov to collect coverage data for kernels compiled with GCC 10.1 causes random malfunctions and kernel crashes. This is the result of a changed GCOV_COUNTERS value in GCC 10.1 that causes a mismatch between the layout of the gcov_info structure created by GCC profiling code and the related structure used by the kernel. Fix this by updating the in-kernel GCOV_COUNTERS value. Also re-enable config GCOV_KERNEL for use with GCC 10. Reported-by:
Colin Ian King <colin.king@canonical.com> Reported-by:
Leon Romanovsky <leonro@nvidia.com> Signed-off-by:
Peter Oberparleiter <oberpar@linux.ibm.com> Tested-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Heikki Krogerus authored
commit 1f3546ff upstream. Failing probe with -EPROBE_DEFER until all dependencies listed in the _DEP (Operation Region Dependencies) object have been met. This will fix an issue where on some platforms UCSI ACPI driver fails to probe because the address space handler for the operation region that the UCSI ACPI interface uses has not been loaded yet. Fixes: 8243edf4 ("usb: typec: ucsi: Add ACPI driver") Cc: stable@vger.kernel.org Signed-off-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.comSigned-off-by:
-
Mathias Nyman authored
commit cfd54fa8 upstream. Userspace drivers that use a SetConfiguration() request to "lightweight" reset an already configured usb device might cause data toggles to get out of sync between the device and host, and the device becomes unusable. The xHCI host requires endpoints to be dropped and added back to reset the toggle. If USB core notices the new configuration is the same as the current active configuration it will avoid these extra steps by calling usb_reset_configuration() instead of usb_set_configuration(). A SetConfiguration() request will reset the device side data toggles. Make sure usb_reset_configuration() function also drops and adds back the endpoints to ensure data toggles are in sync. To avoid code duplication split the current usb_disable_device() function and reuse the endpoint specific part. Cc: stable <stable@vger.kernel.org> Tested-by:
Martin Thierer <mthierer@gmail.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200901082528.12557-1-mathias.nyman@linux.intel.comSigned-off-by:
-
Aleksander Morgado authored
commit 1ac69879 upstream. These modules have 2 different USB layouts: The default layout with PID 0x9205 (AT+CUSBSELNV=1) exposes 4 TTYs and an ECM interface: T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9205 Rev=00.00 S: Manufacturer=SimTech, Incorporated S: Product=SimTech SIM7080 S: SerialNumber=1234567890ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether The purpose of each TTY is as follows: * ttyUSB0: DIAG/QCDM port. * ttyUSB1: GNSS data. * ttyUSB2: AT-capable port (control). * ttyUSB3: AT-capable port (data). In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module exposes 6 TTY ports: T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9206 Rev=00.00 S: Manufacturer=SimTech, Incorporated S: Product=SimTech SIM7080 S: SerialNumber=1234567890ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option The purpose of each TTY is as follows: * ttyUSB0: DIAG/QCDM port. * ttyUSB1: GNSS data. * ttyUSB2: AT-capable port (control). * ttyUSB3: QFLOG interface. * ttyUSB4: DAM interface. * ttyUSB5: AT-capable port (data). Signed-off-by:
Aleksander Morgado <aleksander@aleksander.es> Cc: stable@vger.kernel.org Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Bjørn Mork authored
commit 2bb70f0a upstream. The USB composition, defining the set of exported functions, is dynamic in newer Quectel modems. Default functions can be disabled and alternative functions can be enabled instead. The alternatives includes class functions using interface pairs, which should be handled by the respective class drivers. Active interfaces are numbered consecutively, so static blacklisting based on interface numbers will fail when the composition changes. An example of such an error, where the option driver has bound to the CDC ECM data interface, preventing cdc_ether from handling this function: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0125 Rev= 3.18 S: Manufacturer=Quectel S: Product=EC25-AF C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA A: FirstIf#= 4 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00 I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 16 Ivl=32ms I:* If#= 5 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=option E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Another device with the same id gets correct drivers, since the interface of the network function happens to be blacklisted by option: T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0125 Rev= 3.18 S: Manufacturer=Android S: Product=Android C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Change rules for EC21, EC25, BG96 and EG95 to match vendor specific serial functions only, to prevent binding to class functions. Require 2 endpoints on ff/ff/ff functions, avoiding the 3 endpoint QMI/RMNET network functions. Cc: AceLan Kao <acelan.kao@canonical.com> Cc: Sebastian Sjoholm <ssjoholm@mac.com> Cc: Dan Williams <dcbw@redhat.com> Cc: stable@vger.kernel.org Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Patrick Riphagen authored
commit 6ccc48e0 upstream. The device added has an FTDI chip inside. The device is used to connect Xsens USB Motion Trackers. Cc: stable@vger.kernel.org Signed-off-by:
Patrick Riphagen <patrick.riphagen@xsens.com> Signed-off-by:
-
Zeng Tao authored
commit a18cd6c9 upstream. The USB device descriptor may get changed between two consecutive enumerations on the same device for some reason, such as DFU or malicius device. In that case, we may access the changing descriptor if we don't take the device lock here. The issue is reported: https://syzkaller.appspot.com/bug?id=901a0d9e6519ef8dc7acab25344bd287dd3c7be9 Cc: stable <stable@vger.kernel.org> Cc: Alan Stern <stern@rowland.harvard.edu> Reported-by: syzbot+256e56ddde8b8957eabd@syzkaller.appspotmail.com Fixes: 217a9081 ("USB: add all configs to the "descriptors" attribute") Signed-off-by:
Zeng Tao <prime.zeng@hisilicon.com> Link: https://lore.kernel.org/r/1599201467-11000-1-git-send-email-prime.zeng@hisilicon.comSigned-off-by:
-
Sivaprakash Murugesan authored
commit afd55e6d upstream. There were some problem in ipq8074 Gen2 PCIe phy init sequence. 1. Few register values were wrongly updated in the phy init sequence. 2. The register QSERDES_RX_SIGDET_CNTRL is a RX tuning parameter register which is added in serdes table causing the wrong register was getting updated. 3. Clocks and resets were not added in the phy init. Fix these to make Gen2 PCIe port on ipq8074 devices to work. Fixes: eef243d0 ("phy: qcom-qmp: Add support for IPQ8074") Cc: stable@vger.kernel.org Co-developed-by:
Selvam Sathappan Periakaruppan <speriaka@codeaurora.org> Signed-off-by:
Sivaprakash Murugesan <sivaprak@codeaurora.org> Link: https://lore.kernel.org/r/1596036607-11877-4-git-send-email-sivaprak@codeaurora.orgSigned-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Vaibhav Agarwal authored
commit 1dffeb8b upstream. The current implementation for gbcodec_mixer_dapm_ctl_put() uses uninitialized gbvalue for comparison with updated value. This was found using static analysis with coverity. Uninitialized scalar variable (UNINIT) 11. uninit_use: Using uninitialized value gbvalue.value.integer_value[0]. 460 if (gbvalue.value.integer_value[0] != val) { This patch fixes the issue with fetching the gbvalue before using it for comparision. Fixes: 6339d232 ("greybus: audio: Add topology parser for GB codec") Reported-by:
Vaibhav Agarwal <vaibhav.sr@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/bc4f29eb502ccf93cd2ffd98db0e319fa7d0f247.1597408126.git.vaibhav.sr@gmail.comSigned-off-by:
-
Tetsuo Handa authored
commit bd018a6a upstream. syzbot is reporting OOB read at vga_8planes_imageblit() [1], for "cdat[y] >> 4" can become a negative value due to "const char *cdat". [1] https://syzkaller.appspot.com/bug?id=0d7a0da1557dcd1989e00cb3692b26d4173b4132Reported-by:
syzbot <syzbot+69fbd3e01470f169c8c4@syzkaller.appspotmail.com> Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/90b55ec3-d5b0-3307-9f7c-7ff5c5fd6ad3@i-love.sakura.ne.jpSigned-off-by:
-
Chris Healy authored
commit 2a6838d5 upstream. Add syscon compatibility with Vybrid OCOTP node. This is required to access the UID. Fixes: fa8d20c8 ("ARM: dts: vfxxx: Add node corresponding to OCOTP") Cc: stable@vger.kernel.org Reviewed-by:
Fabio Estevam <festevam@gmail.com> Reviewed-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
Chris Healy <cphealy@gmail.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Wanpeng Li authored
commit 99b82a14 upstream. According to SDM 27.2.4, Event delivery causes an APIC-access VM exit. Don't report internal error and freeze guest when event delivery causes an APIC-access exit, it is handleable and the event will be re-injected during the next vmentry. Signed-off-by:
Wanpeng Li <wanpengli@tencent.com> Message-Id: <1597827327-25055-2-git-send-email-wanpengli@tencent.com> Cc: stable@vger.kernel.org Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Linus Torvalds authored
commit 06a0df4d upstream. Since the softscroll code got removed, this argument is always zero and makes no sense any more. Tested-by:
Yuan Ming <yuanmingbuaa@gmail.com> Tested-by:
Willy Tarreau <w@1wt.eu> Reviewed-by:
-
Linus Torvalds authored
commit 50145474 upstream. This (and the VGA soft scrollback) turns out to have various nasty small special cases that nobody really is willing to fight. The soft scrollback code was really useful a few decades ago when you typically used the console interactively as the main way to interact with the machine, but that just isn't the case any more. So it's not worth dragging along. Tested-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by:
-
Linus Torvalds authored
commit 973c096f upstream. Yunhai Zhang recently fixed a VGA software scrollback bug in commit ebfdfeea ("vgacon: Fix for missing check in scrollback handling"), but that then made people look more closely at some of this code, and there were more problems on the vgacon side, but also the fbcon software scrollback. We don't really have anybody who maintains this code - probably because nobody actually _uses_ it any more. Sure, people still use both VGA and the framebuffer consoles, but they are no longer the main user interfaces to the kernel, and haven't been for decades, so these kinds of extra features end up bitrotting and not really being used. So rather than try to maintain a likely unused set of code, I'll just aggressively remove it, and see if anybody even notices. Maybe there are people who haven't jumped on the whole GUI badnwagon yet, and think it's just a fad. And maybe those people use the scrollback code. If that turns out to be the case, we can resurrect this again, once we've found the sucker^Wmaintainer for it who actually uses it. Reported-by:
NopNop Nop <nopitydays@gmail.com> Tested-by:
Andy Lutomirski <luto@amacapital.net> Acked-by:
-
Yi Zhang authored
commit 60b1af64 upstream. 'parent' sysfs reads will yield '\0' bytes when the interface name has 15 chars, and there will no "\n" output. To reproduce, create one interface with 15 chars: [root@test ~]# ip a s enp0s29u1u7u3c2 2: enp0s29u1u7u3c2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UNKNOWN group default qlen 1000 link/ether 02:21:28:57:47:17 brd ff:ff:ff:ff:ff:ff inet6 fe80::ac41:338f:5bcd:c222/64 scope link noprefixroute valid_lft forever preferred_lft forever [root@test ~]# modprobe rdma_rxe [root@test ~]# echo enp0s29u1u7u3c2 > /sys/module/rdma_rxe/parameters/add [root@test ~]# cat /sys/class/infiniband/rxe0/parent enp0s29u1u7u3c2[root@test ~]# [root@test ~]# f="/sys/class/infiniband/rxe0/parent" [root@test ~]# echo "$(<"$f")" -bash: warning: command substitution: ignored null byte in input enp0s29u1u7u3c2 Use scnprintf and PAGE_SIZE to fill the sysfs output buffer. Cc: stable@vger.kernel.org Fixes: 8700e3e7 ("Soft RoCE driver") Link: https://lore.kernel.org/r/20200820153646.31316-1-yi.zhang@redhat.comSuggested-by:
Yi Zhang <yi.zhang@redhat.com> Reviewed-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
-
Ilya Dryomov authored
commit f44d04e6 upstream. It turns out that currently we rely only on sysfs attribute permissions: $ ll /sys/bus/rbd/{add*,remove*} --w------- 1 root root 4096 Sep 3 20:37 /sys/bus/rbd/add --w------- 1 root root 4096 Sep 3 20:37 /sys/bus/rbd/add_single_major --w------- 1 root root 4096 Sep 3 20:37 /sys/bus/rbd/remove --w------- 1 root root 4096 Sep 3 20:38 /sys/bus/rbd/remove_single_major This means that images can be mapped and unmapped (i.e. block devices can be created and deleted) by a UID 0 process even after it drops all privileges or by any process with CAP_DAC_OVERRIDE in its user namespace as long as UID 0 is mapped into that user namespace. Be consistent with other virtual block devices (loop, nbd, dm, md, etc) and require CAP_SYS_ADMIN in the initial user namespace for mapping and unmapping, and also for dumping the configuration string and refreshing the image header. Cc: stable@vger.kernel.org Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Jeff Layton <jlayton@kernel.org> Signed-off-by:
-
Jordan Crouse authored
commit 7b3f3948 upstream. Temporarily disable preemption on a5xx targets pending some improvements to protect the RPTR shadow from being corrupted. Cc: stable@vger.kernel.org Signed-off-by:
Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by:
Rob Clark <robdclark@chromium.org> Signed-off-by:
-
Linus Walleij authored
commit f7180022 upstream. The TVE200 will occasionally print a bunch of lost interrupts and similar dmesg messages, sometimes during boot and sometimes after disabling and coming back to enablement. This is probably because the hardware is left in an unknown state by the boot loader that displays a logo. This can be fixed by bringing the controller into a known state by resetting the controller while enabling it. We retry reset 5 times like the vendor driver does. We also put the controller into reset before de-clocking it and clear all interrupts before enabling the vblank IRQ. This makes the video enable/disable/enable cycle rock solid on the D-Link DIR-685. Tested extensively. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Acked-by:
-
Hou Pu authored
commit ed43ffea upstream. The iSCSI target login thread might get stuck with the following stack: cat /proc/`pidof iscsi_np`/stack [<0>] down_interruptible+0x42/0x50 [<0>] iscsit_access_np+0xe3/0x167 [<0>] iscsi_target_locate_portal+0x695/0x8ac [<0>] __iscsi_target_login_thread+0x855/0xb82 [<0>] iscsi_target_login_thread+0x2f/0x5a [<0>] kthread+0xfa/0x130 [<0>] ret_from_fork+0x1f/0x30 This can be reproduced via the following steps: 1. Initiator A tries to log in to iqn1-tpg1 on port 3260. After finishing PDU exchange in the login thread and before the negotiation is finished the the network link goes down. At this point A has not finished login and tpg->np_login_sem is held. 2. Initiator B tries to log in to iqn2-tpg1 on port 3260. After finishing PDU exchange in the login thread the target expects to process remaining login PDUs in workqueue context. 3. Initiator A' tries to log in to iqn1-tpg1 on port 3260 from a new socket. A' will wait for tpg->np_login_sem with np->np_login_timer loaded to wait for at most 15 seconds. The lock is held by A so A' eventually times out. 4. Before A' got timeout initiator B gets negotiation failed and calls iscsi_target_login_drop()->iscsi_target_login_sess_out(). The np->np_login_timer is canceled and initiator A' will hang forever. Because A' is now in the login thread, no new login requests can be serviced. Fix this by moving iscsi_stop_login_thread_timer() out of iscsi_target_login_sess_out(). Also remove iscsi_np parameter from iscsi_target_login_sess_out(). Link: https://lore.kernel.org/r/20200729130343.24976-1-houpu@bytedance.com Cc: stable@vger.kernel.org Reviewed-by:
Mike Christie <michael.christie@oracle.com> Signed-off-by:
Hou Pu <houpu@bytedance.com> Signed-off-by:
-
Varun Prakash authored
commit 5528d031 upstream. Current code does not consider 'page_off' in data digest calculation. To fix this, add a local variable 'first_sg' and set first_sg.offset to sg->offset + page_off. Link: https://lore.kernel.org/r/1598358910-3052-1-git-send-email-varun@chelsio.com Fixes: e48354ce ("iscsi-target: Add iSCSI fabric support for target v4.1") Cc: <stable@vger.kernel.org> Reviewed-by:
Mike Christie <michael.christie@oralce.com> Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
-
Michał Mirosław authored
commit 5c065401 upstream. Pull regulator_list_mutex into set_consumer_device_supply() and keep allocations outside of it. Fourth of the fs_reclaim deadlock case. Fixes: 45389c47 ("regulator: core: Add early supply resolution for regulators") Signed-off-by:
Michał Mirosław <mirq-linux@rere.qmqm.pl> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/f0380bdb3d60aeefa9693c4e234d2dcda7e56747.1597195321.git.mirq-linux@rere.qmqm.plSigned-off-by:
-
Filipe Manana authored
commit 1c78544e upstream. When faulting in the pages for the user supplied buffer for the search ioctl, we are passing only the base address of the buffer to the function fault_in_pages_writeable(). This means that after the first iteration of the while loop that searches for leaves, when we have a non-zero offset, stored in 'sk_offset', we try to fault in a wrong page range. So fix this by adding the offset in 'sk_offset' to the base address of the user supplied buffer when calling fault_in_pages_writeable(). Several users have reported that the applications compsize and bees have started to operate incorrectly since commit a48b73ec ("btrfs: fix potential deadlock in the search ioctl") was added to stable trees, and these applications make heavy use of the search ioctls. This fixes their issues. Link: https://lore.kernel.org/linux-btrfs/632b888d-a3c3-b085-cdf5-f9bb61017d92@lechevalier.se/ Link: https://github.com/kilobyte/compsize/issues/34 Fixes: a48b73ec ("btrfs: fix potential deadlock in the search ioctl") CC: stable@vger.kernel.org # 4.4+ Tested-by:
A L <mail@lechevalier.se> Reviewed-by:
Josef Bacik <josef@toxicpanda.com> Signed-off-by:
Filipe Manana <fdmanana@suse.com> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
