- 01 Nov, 2012 19 commits
-
-
Syam Sidhardhan authored
__constant_cpu_to_le*() is the right go here. Signed-off-by:
Syam Sidhardhan <s.syam@samsung.com> Acked-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk>
-
Syam Sidhardhan authored
For files only using THIS_MODULE and/or EXPORT_SYMBOL, map them onto including export.h -- or if the file isn't even using those, then just delete the include. Signed-off-by:
-
Andrei Emeltchenko authored
When refcnt reaches zero disconnect timeout will run and hci_conn will be disconnected. Signed-off-by:
Andrei Emeltchenko <andrei.emeltchenko@intel.com> Acked-by:
-
Andrei Emeltchenko authored
After receiving HCI Logical Link Complete event finish EFS configuration by sending L2CAP Conf Response with success code. Signed-off-by:
-
Andrei Emeltchenko authored
Add processing for HCI Physical Link Complete event. Upon successful status received start L2CAP create channel process. Signed-off-by:
-
Andrei Emeltchenko authored
There is helper function used to send EFS Configuration Response. Signed-off-by:
-
Andrei Emeltchenko authored
Assignment is not needed here since err is always gets value. Signed-off-by:
-
Johan Hedberg authored
This patch fixes sending an unnecessary HCI_LE_Host_Enable command if the command has already been sent as part of the default HCI init sequence. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
-
Johan Hedberg authored
When powered on the EIR data gets updated as the last step by mgmt. Therefore avoid an update when getting a local name update as that's part of the normal HCI init sequence. Signed-off-by:
-
Johan Hedberg authored
This patch fixes sending an unnecessary HCI_Write_SSP_Mode command if the command has already been sent as part of the default HCI init sequence. Signed-off-by:
-
Johan Hedberg authored
When we get a successful command complete for HCI_Write_SSP_Mode we need to update the host feature bits for the hdev struct accordingly. Signed-off-by:
-
Johan Hedberg authored
When an adapter is in the LE peripheral role scanning for other devices or initiating connections to them is not allowed. This patch makes sure that such attempts will result in appropriate error returns. Signed-off-by:
-
Johan Hedberg authored
This patch adds a flag to be used for LE GAP Peripheral role. In this role undirected advertising will be enabled and operations not allowed in Peripheral role (such as scanning and initiating connections) will be disallowed. Signed-off-by:
-
Johan Hedberg authored
For better code readability and avoiding simple bugs of checking the wrong byte of the features make use of feature test macros whenever possible. Signed-off-by:
-
Johan Hedberg authored
This patch adds missing feature test macros needed for various use cases and also sorts the macros according to the feature bit location in the feature mask (for easy lookup). Signed-off-by:
-
Johan Hedberg authored
When LE has been enabled with the simultaneous BR/EDR & LE parameter set to true we should also update the host features stored in struct hci_dev accordingly. Signed-off-by:
-
Johan Hedberg authored
This patch makes sure that settings which are specific for BR/EDR capable adapters are not allowed for non-BR/EDR (e.g. LE-only) adapters. Instead, a "not supported" error is returned of such a setting is attempted to be set for a non-BR/EDR adapter. Signed-off-by:
-
Johan Hedberg authored
This patch makes sure that we don't send BR/EDR-only commands for LE-only adapters when they get powered on. Doing this would just cause command errors. Signed-off-by:
-
Denis Kirjanov authored
Replace list_for_each with list_for_each_entry() helper Signed-off-by:
Denis Kirjanov <kirjanov@gmail.com> Acked-by:
-
- 24 Oct, 2012 21 commits
-
-
Gustavo Padovan authored
le_init() and bredr_init() are now called le_setup() and bredr_setup() to avoid duplicates names over the tree even if they are all static. Signed-off-by: -
Johan Hedberg authored
This patch adds the reading of the LE advertising channel TX power to the HCI init sequence of LE-capable controllers. This data will be used e.g. for inclusion in the advertising data packets when advertising is enabled. Signed-off-by:
-
Johan Hedberg authored
This patch adds setting of the LE event mask to the HCI init procedure for LE-capable controllers. Right now we only set the default mask which is good enough for the events available in the 4.0 core specification. Signed-off-by:
-
Johan Hedberg authored
This patch fixes the use of le_mtu and le_pkts values in the HCIGETDEVINFO ioctl for LE-only controllers. Signed-off-by:
-
Johan Hedberg authored
This patch splits off most the HCI init sequence commands from a fixed set into a conditional one that is sent once the HCI_Read_Local_Features and HCI_Read_Local_Version_Information commands complete. This is necessary since many of the current fixed commands are not allowed for LE-only controllers. Signed-off-by:
-
Syam Sidhardhan authored
include <linux/export.h> is the right to go here. Signed-off-by:
-
Syam Sidhardhan authored
Trivial fix. Signed-off-by:
-
Mat Martineau authored
Channel moves are triggered by changes to the BT_CHANNEL_POLICY sockopt when an ERTM or streaming-mode channel is connected. Moves are only started if enable_hs is true. Signed-off-by:
Mat Martineau <mathewm@codeaurora.org> Acked-by:
-
Mat Martineau authored
Do not retransmit previously-sent data when a "receiver ready" s-frame with the "final" flag is received during a move. The ERTM state machines will resynchronize at the end of a channel move, and the state machine needs to avoid state changes during a move. Signed-off-by:
-
Mat Martineau authored
When operating over BR/EDR, ERTM accounts for the maximum over-the-air packet size when setting the PDU size. AMP controllers do not use the same over-the-air packets, so the PDU size should only be based on the HCI MTU of the AMP controller. Signed-off-by:
-
Mat Martineau authored
The L2CAP spec recommends specific retransmit and monitor timeouts for ERTM channels that are on AMP controllers. These timeouts are calculated from the AMP controller's best effort flush timeout. BR/EDR controllers use the default retransmit and monitor timeouts. Signed-off-by:
-
Mat Martineau authored
Outgoing ERTM data is queued during a channel move. The ERTM state machine is partially reset at the start of a move, and must be resynchronized with the remote state machine at the end of the move. Data is not sent so that there are no state transitions between the partial reset and the resync. Streaming mode frames are dropped during a move. Signed-off-by:
-
Mat Martineau authored
AMP controllers expect to transmit only "complete" ACL frames. These frames have both the "start" and "cont" bits set. AMP does not allow fragmented ACLs. Signed-off-by:
-
Mat Martineau authored
Several different actions may be taken when an AMP physical link becomes available. A channel being created on an AMP controller must continue the connection process. A channel being moved needs to either send a move request or a move response. A failed physical link will revert to using a BR/EDR controller if possible. Signed-off-by:
-
Mat Martineau authored
The move confirm response concludes the channel move command sequence. Receipt of this command indicates that data may begin to flow again. Signed-off-by:
-
Mat Martineau authored
The logical link confirm callback is executed when the AMP controller completes its logical link setup. During a channel move, a newly formed logical link allows a move responder to send a move channel response. A move initiator will send a move channel confirm. A failed logical link will end the channel move and send an appropriate response or confirm command indicating a failure. If the channel is being created on an AMP controller, L2CAP configuration is completed after the logical link is set up. Signed-off-by:
-
Mat Martineau authored
The move response command includes a result code indicating "pending", "success", or "failure" status. A pending result is received when the remote address is still setting up a physical link, and will be followed by success or failure. On success, logical link setup will proceed. On failure, the move is stopped. The receiver of a move channel response must always follow up by sending a move channel confirm command. Signed-off-by:
-
Mat Martineau authored
On an AMP controller, hci_chan maps to a logical link. When a channel is being moved, the logical link may or may not be connected already. The hci_chan->state is used to determine the existance of a useable logical link so the link can be either used or requested. Signed-off-by:
-
Mat Martineau authored
After sending a move channel response, a move responder waits for a move channel confirm command. If the received command has a "confirmed" result the move is proceeding, and "unconfirmed" means the move has failed and the channel will not change controllers. Signed-off-by:
-
Mat Martineau authored
Two new states are required to implement channel moves with the ERTM receive state machine. The "WAIT_P" state is used by a move responder to wait for a "poll" flag after a move is completed (success or failure). "WAIT_F" is similarly used by a move initiator to wait for a "final" flag when the move is completing. In either state, the reqseq value in the poll/final frame tells the state machine exactly which frame should be expected next. Signed-off-by:
-
Mat Martineau authored
On receipt of a channel move request, the request must be validated based on the L2CAP mode, connection state, and controller capabilities. ERTM channels must have their state machines cleared and transmission paused while the channel move takes place. If the channel is being moved to an AMP controller then an AMP physical link must be prepared. Moving the channel back to BR/EDR proceeds immediately. Signed-off-by:
-
