- 12 Sep, 2012 13 commits
-
-
Bjørn Mork authored
commit 4cbbb039 upstream. Tested-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Ozan Çağlayan authored
commit 7724a1ed upstream. This adds VID/PID for Kondo Kagaku Co. Ltd. Serial USB Adapter interface: http://www.kondo-robot.com/EN/wp/?cat=28 Tested by controlling an RCB3 board using libRCB3. Signed-off-by:
Ozan Çağlayan <ozancag@gmail.com> Signed-off-by:
-
Sarah Sharp authored
commit 5cb7df2b upstream. Gary reports that with recent kernels, he notices more xHCI driver warnings: xhci_hcd 0000:03:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk? We think his Etron xHCI host controller may have the same buggy behavior as the Fresco Logic xHCI host. When a short transfer is received, the host will mark the transfer as successfully completed when it should be marking it with a short completion. Fix this by turning on the XHCI_TRUST_TX_LENGTH quirk when the Etron host is discovered. Note that Gary has revision 1, but if Etron fixes this bug in future revisions, the quirk will have no effect. This patch should be backported to kernels as old as 2.6.36, that contain a backported version of commit 1530bbc6 "xhci: Add new short TX quirk for Fresco Logic host." Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by:
Gary E. Miller <gem@rellim.com> Signed-off-by:
-
Sarah Sharp authored
commit 22ceac19 upstream. The NEC/Renesas 720201 xHCI host controller does not complete its reset within 250 milliseconds. In fact, it takes about 9 seconds to reset the host controller, and 1 second for the host to be ready for doorbell rings. Extend the reset and CNR polling timeout to 10 seconds each. This patch should be backported to kernels as old as 2.6.31, that contain the commit 66d4eadd "USB: xhci: BIOS handoff and HW initialization." Signed-off-by:
Edwin Klein Mentink <e.kleinmentink@zonnet.nl> [bwh: Backported to 3.2: result of second handshake call is returned directly] Signed-off-by:
-
Szymon Janc authored
commit a9ea3ed9 upstream. Some devices e.g. some Android based phones don't do SDP search before pairing and cancel legacy pairing when ACL is disconnected. PIN Code Request event which changes ACL timeout to HCI_PAIRING_TIMEOUT is only received after remote user entered PIN. In that case no L2CAP is connected so default HCI_DISCONN_TIMEOUT (2 seconds) is being used to timeout ACL connection. This results in problems with legacy pairing as remote user has only few seconds to enter PIN before ACL is disconnected. Increase disconnect timeout for incomming connection to HCI_PAIRING_TIMEOUT if SSP is disabled and no linkey exists. To avoid keeping ACL alive for too long after SDP search set ACL timeout back to HCI_DISCONN_TIMEOUT when L2CAP is connected. 2012-07-19 13:24:43.413521 < HCI Command: Create Connection (0x01|0x0005) plen 13 bdaddr 00:02:72:D6:6A:3F ptype 0xcc18 rswitch 0x01 clkoffset 0x0000 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 2012-07-19 13:24:43.425224 > HCI Event: Command Status (0x0f) plen 4 Create Connection (0x01|0x0005) status 0x00 ncmd 1 2012-07-19 13:24:43.885222 > HCI Event: Role Change (0x12) plen 8 status 0x00 bdaddr 00:02:72:D6:6A:3F role 0x01 Role: Slave 2012-07-19 13:24:44.054221 > HCI Event: Connect Complete (0x03) plen 11 status 0x00 handle 42 bdaddr 00:02:72:D6:6A:3F type ACL encrypt 0x00 2012-07-19 13:24:44.054313 < HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2 handle 42 2012-07-19 13:24:44.055176 > HCI Event: Page Scan Repetition Mode Change (0x20) plen 7 bdaddr 00:02:72:D6:6A:3F mode 0 2012-07-19 13:24:44.056217 > HCI Event: Max Slots Change (0x1b) plen 3 handle 42 slots 5 2012-07-19 13:24:44.059218 > HCI Event: Command Status (0x0f) plen 4 Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 0 2012-07-19 13:24:44.062192 > HCI Event: Command Status (0x0f) plen 4 Unknown (0x00|0x0000) status 0x00 ncmd 1 2012-07-19 13:24:44.067219 > HCI Event: Read Remote Supported Features (0x0b) plen 11 status 0x00 handle 42 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87 2012-07-19 13:24:44.067248 < HCI Command: Read Remote Extended Features (0x01|0x001c) plen 3 handle 42 page 1 2012-07-19 13:24:44.071217 > HCI Event: Command Status (0x0f) plen 4 Read Remote Extended Features (0x01|0x001c) status 0x00 ncmd 1 2012-07-19 13:24:44.076218 > HCI Event: Read Remote Extended Features (0x23) plen 13 status 0x00 handle 42 page 1 max 1 Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00 2012-07-19 13:24:44.076249 < HCI Command: Remote Name Request (0x01|0x0019) plen 10 bdaddr 00:02:72:D6:6A:3F mode 2 clkoffset 0x0000 2012-07-19 13:24:44.081218 > HCI Event: Command Status (0x0f) plen 4 Remote Name Request (0x01|0x0019) status 0x00 ncmd 1 2012-07-19 13:24:44.105214 > HCI Event: Remote Name Req Complete (0x07) plen 255 status 0x00 bdaddr 00:02:72:D6:6A:3F name 'uw000951-0' 2012-07-19 13:24:44.105284 < HCI Command: Authentication Requested (0x01|0x0011) plen 2 handle 42 2012-07-19 13:24:44.111207 > HCI Event: Command Status (0x0f) plen 4 Authentication Requested (0x01|0x0011) status 0x00 ncmd 1 2012-07-19 13:24:44.112220 > HCI Event: Link Key Request (0x17) plen 6 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:44.112249 < HCI Command: Link Key Request Negative Reply (0x01|0x000c) plen 6 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:44.115215 > HCI Event: Command Complete (0x0e) plen 10 Link Key Request Negative Reply (0x01|0x000c) ncmd 1 status 0x00 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:44.116215 > HCI Event: PIN Code Request (0x16) plen 6 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:48.099184 > HCI Event: Auth Complete (0x06) plen 3 status 0x13 handle 42 Error: Remote User Terminated Connection 2012-07-19 13:24:48.179182 > HCI Event: Disconn Complete (0x05) plen 4 status 0x00 handle 42 reason 0x13 Reason: Remote User Terminated Connection Signed-off-by:
Szymon Janc <szymon.janc@tieto.com> Acked-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk> [bwh: Backported to 3.2: - Adjust context - hci_conn_ssp_enabled() is not defined; open-code the condition] Signed-off-by:
-
Zach Brown authored
commit fb6ccff6 upstream. Commit 7572777e attempted to verify that the total iovec from the client doesn't overflow iov_length() but it only checked the first element. The iovec could still overflow by starting with a small element. The obvious fix is to check all the elements. The overflow case doesn't look dangerous to the kernel as the copy is limited by the length after the overflow. This fix restores the intention of returning an error instead of successfully copying less than the iovec represented. I found this by code inspection. I built it but don't have a test case. I'm cc:ing stable because the initial commit did as well. Signed-off-by:
Zach Brown <zab@redhat.com> Signed-off-by:
Miklos Szeredi <mszeredi@suse.cz> Signed-off-by:
-
Theodore Ts'o authored
commit 7e731bc9 upstream. Commit 03179fe9 introduced a kmemcheck complaint in ext4_da_get_block_prep() because we save and restore ei->i_da_metadata_calc_last_lblock even though it is left uninitialized in the case where i_da_metadata_calc_len is zero. This doesn't hurt anything, but silencing the kmemcheck complaint makes it easier for people to find real bugs. Addresses https://bugzilla.kernel.org/show_bug.cgi?id=45631 (which is marked as a regression). Signed-off-by:
"Theodore Ts'o" <tytso@mit.edu> Signed-off-by:
-
Idan Kedar authored
commit 8554116e upstream. we have encountered a bug whereby reading a lot of files (copying fedora's /bin) from a pNFS mount and hitting Ctrl+C in the middle caused a general protection fault in xdr_shrink_bufhead. this function is called when decoding the response from LAYOUTGET. the decoding is done by a worker thread, and the caller of LAYOUTGET waits for the worker thread to complete. hitting Ctrl+C caused the synchronous wait to end and the next thing the caller does is to free the pages, so when the worker thread calls xdr_shrink_bufhead, the pages are gone. therefore, the cleanup of these pages has been moved to nfs4_layoutget_release. Signed-off-by:
Idan Kedar <idank@tonian.com> Signed-off-by:
Benny Halevy <bhalevy@tonian.com> Signed-off-by:
Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by:
-
Jim Rees authored
commit 10bd295a upstream. Signed-off-by:
Jim Rees <rees@umich.edu> Suggested-by:
Andy Adamson <andros@netapp.com> Suggested-by:
Fred Isaman <iisaman@netapp.com> Signed-off-by:
-
Andy Adamson authored
commit e5265a0c upstream. Signed-off-by:
-
Trond Myklebust authored
commit 7d9dea91 upstream. Signed-off-by:
-
Jeff Layton authored
commit 3dd4765f upstream. ...and ensure that we tear down the nfs_commit_data cache too when unloading the module. Cc: Bryan Schumaker <bjschuma@netapp.com> Signed-off-by:
Jeff Layton <jlayton@redhat.com> Signed-off-by:
-
Cyrus Lien authored
commit 2d8767bb upstream. Add Asus All-In-One PC keyboard model AK1D. BugLink: https://bugs.launchpad.net/bugs/1027789Signed-off-by:
Cyrus Lien <cyrus.lien@canonical.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
- 19 Aug, 2012 27 commits
-
-
Ben Hutchings authored
-
Jerome Glisse authored
commit 81ee8fb6 upstream. It seems we can not update the crtc scanout address. After disabling crtc, update to base address do not take effect after crtc being reenable leading to at least frame being scanout from the old crtc base address. Disabling crtc display request lead to same behavior. So after changing the vram address if we don't keep crtc disabled we will have the GPU trying to read some random system memory address with some iommu this will broke the crtc engine and will lead to broken display and iommu error message. So to avoid this, disable crtc. For flicker less boot we will need to avoid moving the vram start address. This patch should also fix : https://bugs.freedesktop.org/show_bug.cgi?id=42373Signed-off-by:
Jerome Glisse <jglisse@redhat.com> Signed-off-by:
-
Alex Deucher authored
commit 5b23c904 upstream. Handle the 16 bank case. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> [bwh: Backported to 3.2: adjust context, indentation] Signed-off-by:
-
Alex Deucher authored
commit c8d15edc upstream. Handle the 16 bank case. Signed-off-by:
-
Heiko Carstens authored
commit e8587121 upstream. The native 31 bit and the compat behaviour for the mmap system calls differ: In native 31 bit mode the passed in address for the mmap system call will be unmodified passed to sys_mmap_pgoff(). In compat mode however the passed in address will be modified with compat_ptr() which masks out the most significant bit. The result is that in native 31 bit mode each mmap request (with MAP_FIXED) will fail where the most significat bit is set, while in compat mode it may succeed. This odd behaviour was introduced with d3815898 "[S390] mmap: add missing compat_ptr conversion to both mmap compat syscalls". To restore a consistent behaviour accross native and compat mode this patch functionally reverts the above mentioned commit. Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Heiko Carstens authored
commit 82aabdb6 upstream. The compat wrappers incorrectly called the non compat versions of the system process_vm system calls. Signed-off-by:
-
Daniel Vetter authored
commit 0d8957c8 upstream. We may only start to set up the new register values after having confirmed that the ring is truely off. Otherwise the hw might lose the newly written register values. This is caught later on in the init sequence, when we check whether the register writes have stuck. Reviewed-by:
Jani Nikula <jani.nikula@intel.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50522Tested-by:
Yang Guang <guang.a.yang@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Sean Paul authored
commit f01db988 upstream. I have seen a number of "blt ring initialization failed" messages where the ctl or start registers are not the correct value. Upon further inspection, if the code just waited a little bit, it would read the correct value. Adding the wait_for to these reads should eliminate the issue. Signed-off-by:
Sean Paul <seanpaul@chromium.org> Reviewed-by:
Ben Widawsky <ben@bwidawsk.net> Signed-off-by:
-
Arnd Bergmann authored
commit 4eef6cbf upstream. The EETI touchscreen asserts its IRQ line as soon as it has data in its internal buffers. The line is automatically deasserted once all data has been read via I2C. Hence, the driver has to monitor the GPIO line and cannot simply rely on the interrupt handler reception. In the current implementation of the driver, irq_to_gpio() is used to determine the GPIO number from the i2c_client's IRQ value. As irq_to_gpio() is not available on all platforms, this patch changes this and makes the driver ignore the passed in IRQ. Instead, a GPIO is added to the platform_data struct and gpio_to_irq is used to derive the IRQ from that GPIO. If this fails, bail out. The driver is only able to work in environments where the touchscreen GPIO can be mapped to an IRQ. Without this patch, building raumfeld_defconfig results in: drivers/input/touchscreen/eeti_ts.c: In function 'eeti_ts_irq_active': drivers/input/touchscreen/eeti_ts.c:65:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration] Signed-off-by:
Daniel Mack <zonque@gmail.com> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Sven Neumann <s.neumann@raumfeld.com> Cc: linux-input@vger.kernel.org Cc: Haojian Zhuang <haojian.zhuang@gmail.com> [bwh: Backported to 3.2: raumfeld_controller_i2c_board_info.irq was initialised using gpio_to_irq(), but this doesn't seem to matter] Signed-off-by:
-
Arnd Bergmann authored
commit 59ee93a5 upstream. The irq_to_gpio function was removed from the pxa platform in linux-3.2, and this driver has been broken since. There is actually no in-tree user of this driver that adds this platform device, but the driver can and does get enabled on some platforms. Without this patch, building ezx_defconfig results in: drivers/mfd/ezx-pcap.c: In function 'pcap_isr_work': drivers/mfd/ezx-pcap.c:205:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration] Signed-off-by:
Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Daniel Ribeiro <drwyrm@gmail.com> Signed-off-by:
-
David Henningsson authored
commit 012e7eb1 upstream. The same ID is twice in the quirk table, so the second one is not used. Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
David Henningsson authored
commit e9fc83cb upstream. This computer is confirmed working with model=auto on kernel 3.2. Also, parsing fails with hda-emu with the current model. Signed-off-by:
-
Tushar Dave authored
commit b7ec70be upstream. Found that commit d478eb44 was a bad commit. If the link partner is transmitting codeword (even if NULL codeword), then the RXCW.C bit will be set so check for RXCW.CW is unnecessary. Ref: RH BZ 840642 Reported-by:
Fabio Futigami <ffutigam@redhat.com> Signed-off-by:
Tushar Dave <tushar.n.dave@intel.com> CC: Marcelo Ricardo Leitner <mleitner@redhat.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by:
-
Felix Kaechele authored
commit c8415a48 upstream. As with the ThinkPad Models X230 Tablet and T530 the X230 needs a qurik to correctly set up the pins for the dock port. Signed-off-by:
Felix Kaechele <felix@fetzig.org> Signed-off-by:
-
Johannes Berg authored
commit 50e2a30c upstream. There's a bug that causes the rate scaling to get stuck when it has to use single-stream rates with a peer that can do GF and SGI; the two are incompatible so we can't use them together, but that causes the algorithm to not work at all, it always rejects updates. Disable greenfield for now to prevent that problem. Reviewed-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Tested-by:
Cesar Eduardo Barros <cesarb@cesarb.net> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Stanislaw Gruszka authored
commit deee0214 upstream. We can not pass NULL libconf->conf->channel to rt61pci_config() as it is dereferenced unconditionally in rt61pci_config_lna_gain() subroutine. Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=44361 Reported-and-tested-by: <dolohow@gmail.com> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Daniel Drake authored
commit 1f6fc43e upstream. libertas currently calls cfg80211_disconnected() when it is being brought down. This causes an event to be allocated, but since the wdev is already removed from the rdev by the time that the event processing work executes, the event is never processed or freed. http://article.gmane.org/gmane.linux.kernel.wireless.general/95666 Fix this leak, and other possible situations, by processing the event queue when a device is being unregistered. Thanks to Johannes Berg for the suggestion. Signed-off-by:
Daniel Drake <dsd@laptop.org> Reviewed-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Philipp A. Mohrenweiser authored
commit 4407be6b upstream. Add a model/fixup string "lenovo-dock", for Thinkpad T430s, to allow sound in docking station. Tested on Lenovo T430s with ThinkPad Mini Dock Plus Series 3 Signed-off-by:
Philipp A. Mohrenweiser <phiamo@googlemail.com> Signed-off-by:
-
Marek Vasut authored
commit 3bed491c upstream. The CONFIG_DEFAULT_MMAP_MIN_ADDR was set to 65536 in mxs_defconfig, this caused severe breakage of userland applications since the upper limit for ARM is 32768. By default CONFIG_DEFAULT_MMAP_MIN_ADDR is set to 4096 and can also be changed via /proc/sys/vm/mmap_min_addr if needed. Quoting Russell King [1]: "4096 is also fine for ARM too. There's not much point in having defconfigs change it - that would just be pure noise in the config files." the CONFIG_DEFAULT_MMAP_MIN_ADDR can be removed from the defconfig altogether. This problem was introduced by commit cde7c41f (ARM: configs: add defconfig for mach-mxs). [1] http://marc.info/?l=linux-arm-kernel&m=134401593807820&w=2Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Russell King <linux@arm.linux.org.uk> Cc: Wolfgang Denk <wd@denx.de> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
commit d4e5979c upstream. AR1111 is same as AR9485. The h/w difference between them is quite insignificant, Felix suggests only very few baseband features may not be available in AR1111. The h/w code for AR9485 is already present, so AR1111 should work fine with the addition of its PID/VID. Cc: Felix Bitterli <felixb@qca.qualcomm.com> Reported-by:
Tim Bentley <Tim.Bentley@Gmail.com> Signed-off-by:
Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Tested-by:
-
Johannes Berg authored
commit dd4c9260 upstream. The mesh path timer needs to be canceled when leaving the mesh as otherwise it could fire after the interface has been removed already. Signed-off-by:
-
Stefan Bader authored
Based on commit fee84b07 upstream. Intercept RDPMC and forward it to the PMU emulation code. Newer vmx support will only allow to load the kvm_intel module if RDPMC_EXITING is supported. Even without the actual support this part of the change is required on 3.2 hosts. BugLink: http://bugs.launchpad.net/bugs/1031090Signed-off-by:
Stefan Bader <stefan.bader@canonical.com> Signed-off-by:
Avi Kivity <avi@redhat.com> Signed-off-by:
-
Daniel Vetter authored
commit 53d227f2 upstream. Currently we reserve seqnos only when we emit the request to the ring (by bumping dev_priv->next_seqno), but start using it much earlier for ring->oustanding_lazy_request. When 2 threads compete for the gpu and run on two different rings (e.g. ddx on blitter vs. compositor) hilarity ensued, especially when we get constantly interrupted while reserving buffers. Breakage seems to have been introduced in commit 6f392d54 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Sat Aug 7 11:01:22 2010 +0100 drm/i915: Use a common seqno for all rings. This patch fixes up the seqno reservation logic by moving it into i915_gem_next_request_seqno. The ring->add_request functions now superflously still return the new seqno through a pointer, that will be refactored in the next patch. Note that with this change we now unconditionally allocate a seqno, even when ->add_request might fail because the rings are full and the gpu died. But this does not open up a new can of worms because we can already leave behind an outstanding_request_seqno if e.g. the caller gets interrupted with a signal while stalling for the gpu in the eviciton paths. And with the bugfix we only ever have one seqno allocated per ring (and only that ring), so there are no ordering issues with multiple outstanding seqnos on the same ring. v2: Keep i915_gem_get_seqno (but move it to i915_gem.c) to make it clear that we only have one seqno counter for all rings. Suggested by Chris Wilson. v3: As suggested by Chris Wilson use i915_gem_next_request_seqno instead of ring->oustanding_lazy_request to make the follow-up refactoring more clearly correct. Also improve the commit message with issues discussed on irc. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45181 Tested-by: Nicolas Kalkhof nkalkhof()at()web.de Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-Off-by:
-
Janne Kalliomäki authored
commit a6dc8c04 upstream. The variable io_size was unsigned int, which caused the wrong sector number to be calculated after aligning it. This then caused mount to fail with big volumes, as backup volume header information was searched from a wrong sector. Signed-off-by:
Janne Kalliomäki <janne@tuxera.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Larry Finger authored
commit 3ce4d85b upstream. In commit a7959c13, the USB part of rtlwifi was switched to convert _usb_read_sync() to using a preallocated buffer rather than one that has been acquired using kmalloc. Although this routine is named as though it were synchronous, there seem to be simultaneous users, and the selection of the index to the data buffer is not multi-user safe. This situation is addressed by adding a new spinlock. The routine cannot sleep, thus a mutex is not allowed. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Dean Nelson authored
commit b868179c upstream. Commit d5bc77a2 broke Wake-on-LAN by inadvertently dropping the enabling of DMA receives. Restore the enabling of DMA receives for WoL. This is applicable to 3.1+ stable trees. Reported-by:
Tobias Klausmann <klausman@schwarzvogel.de> Signed-off-by:
Dean Nelson <dnelson@redhat.com> Tested-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Mathias Krause authored
[ Upstream commits a117dacd and 8bbb1813 ] The tun module leaks up to 36 bytes of memory by not fully initializing a structure located on the stack that gets copied to user memory by the TUNGETIFF and SIOCGIFHWADDR ioctl()s. Signed-off-by:
Mathias Krause <minipli@googlemail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
