- 09 Jun, 2020 1 commit
-
-
Matt Roper authored
Rocket Lake uses the same 'abox0' mechanism to handle pixel data transfers from memory that gen11 platforms used, rather than the abox1/abox2 interfaces used by TGL/DG1. For the most part this is a hardware implementation detail that's transparent to driver software, but we do have to program a couple of tuning registers (MBUS_ABOX_CTL and BW_BUDDY registers) according to which ABOX instances are used by a platform. Let's track the platform's ABOX usage in the device info structure and use that to determine which instances of these registers to program. As an exception to this rule is that even though TGL/DG1 use ABOX1+ABOX2 for data transfers, we're still directed to program the ABOX_CTL register for ABOX0; so we'll handle that as a special case. v2: - Store the mask of platform-specific abox registers in the device info structure. - Add a TLB_REQ_TIMER() helper macro. (Aditya) v3: - Squash ABOX and BW_BUDDY patches together and use a single mask for both of them, plus a special-case for programming the ABOX0 instance on all gen12. (Ville) Bspec: 50096 Bspec: 49218 Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Aditya Swarup <aditya.swarup@intel.com> Signed-off-by:
Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200606025740.3308880-2-matthew.d.roper@intel.comReviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com>
-
- 08 Jun, 2020 3 commits
-
-
Chris Wilson authored
In some of our hangtests, we try to reset an active engine while it is spinning inside the recursive spinner. However, we also try to flood the engine with requests that preempt the hang, and so should disable the preemption to be sure that we reset the right request. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200607222108.14401-2-chris@chris-wilson.co.uk
-
Tvrtko Ursulin authored
Sentinels are supposed to be last requests in the elsp queue, not the only one, so adjust the assert accordingly. Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by:
-
Stanislav Lisovskiy authored
This reverts commit 82ea174d. Unfortunately according to our recent findings there is still some unidentified factor, requiring CDCLK to be set higher - otherwise we still get underruns on some multipipe configurations, despite CDCLK being set according to BSpec formula. So getting again back into debug mode to indentify the cause, meanwhile setting CDCLK=Pixel rate back in order to remove regression in 10% of the cases due to FIFO underruns. Signed-off-by:
Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Fixes: cd191546 ("drm/i915: Adjust CDCLK accordingly to our DBuf bw needs") Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200608065552.21728-1-stanislav.lisovskiy@intel.com
-
- 07 Jun, 2020 1 commit
-
-
Gwan-gyeong Mun authored
The IO buffer Wake and Fast Wake bit size and value have been changed from Gen12+. It programs the default value of IO buffer Wake and Fast Wake on Gen12+. It adds definitions of IO buffer Wake and Fast Wake for pre Gen12 and Gen12+. And it aligns PSR2 definition macros. v2: Fix macro definitions. (José) v3: Addressed review comments from José - Add missing default values of IO_BUFFER_WAKE and FAST_WAKE for GEN9+ - Change a style of macro naming in order to use lines as input. - Update Todo comments. v4: Add parentheses to macros to avoid precedence issues. Cc: José Roberto de Souza <jose.souza@intel.com> Signed-off-by:
Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Reviewed-by:
José Roberto de Souza <jose.souza@intel.com> Signed-off-by:
-
- 06 Jun, 2020 1 commit
-
-
Matt Roper authored
We accidentally dropped matching for DVO_PORT_DPE from the VBT mapping table when we refactored the function. Restore it. Fixes: 4628142a ("drm/i915/rkl: provide port/phy mapping for vbt") Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
-
- 05 Jun, 2020 9 commits
-
-
Chris Wilson authored
Unused as of commit 9e0f9464 ("drm/i915/gem: Async GPU relocations only"), but left behind. >> drivers/gpu/drm/i915/gem/i915_gem_execbuffer.c:933:21: error: unused function 'unmask_page' [-Werror,-Wunused-function] static inline void *unmask_page(unsigned long p) ^ >> drivers/gpu/drm/i915/gem/i915_gem_execbuffer.c:938:28: error: unused function 'unmask_flags' [-Werror,-Wunused-function] static inline unsigned int unmask_flags(unsigned long p) ^ >> drivers/gpu/drm/i915/gem/i915_gem_execbuffer.c:945:33: error: unused function 'cache_to_ggtt' [-Werror,-Wunused-function] static inline struct i915_ggtt *cache_to_ggtt(struct reloc_cache *cache) Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200605200357.13069-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
As a last minute addition, I added an assertion to make sure that the new i915_vma view would be equal to the discard. However, the positive encouragement from CI only goes to show that we rarely take this path, and it wasn't until the post-merge run did we hit the assert -- because it compared the wrong view. Fixup the copy'n'paste error and compare against both the old view and the expected new view. Fixes: 9bdcaa5e ("drm/i915: Discard a misplaced GGTT vma") Signed-off-by:
-
Chris Wilson authored
Across the many users of the GGTT vma (internal objects, mmapings, display etc), we may end up with conflicting requirements for the placement. Currently, we try to resolve the conflict by unbinding the vma and rebinding it to match the new constraints; over time we will end up with a GGTT that matches the most strict constraints over all concurrent users. However, this causes a problem if the vma is currently in use as we must wait until it is idle before moving it. But there is no restriction on the number of views we may use (apart from the limited size of the GGTT itself), and so if the active vma does not meet our requirements, try and build a new one! Signed-off-by:
-
Chris Wilson authored
We may choose not to submit for a number of reasons, yet not fill both ELSP. In which case we must start timeslicing (there will be no ACK event on which to hook the start) if the queue would benefit from the currently active context being evicted. Signed-off-by:
-
Chris Wilson authored
If we only submit the first port, leaving the second empty yet have ready requests pending in the queue, use that to set the timeslicing priority (i.e. the priority at which we will decided to enabling timeslicing and evict the currently active context if the queue is of equal priority after its quantum expired). Signed-off-by:
-
Chris Wilson authored
Add engine->fw_domain/active to the pretty printer for debug dumps and debugfs. Signed-off-by:
-
Kees Cook authored
This has no code changes, but the typo is clearly getting copy/pasted, so better to avoid this now and fix the typo. IS_ENABLED() takes full names, and must have the "CONFIG_" prefix. Reported-by:
Joe Perches <joe@perches.com> Link: https://lore.kernel.org/lkml/b08611018fdb6d88757c6008a5c02fa0e07b32fb.camel@perches.comSigned-off-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
-
Chris Wilson authored
Reduce the 3 relocation paths down to the single path that accommodates all. The primary motivation for this is to guard the relocations with a natural fence (derived from the i915_request used to write the relocation from the GPU). The tradeoff in using async gpu relocations is that it increases latency over using direct CPU relocations, for the cases where the target is idle and accessible by the CPU. The benefit is greatly reduced lock contention and improved concurrency by pipelining. Note that forcing the async gpu relocations does reveal a few issues they have. Firstly, is that they are visible as writes to gem_busy, causing to mark some buffers are being to written to by the GPU even though userspace only reads. Secondly is that, in combination with the cmdparser, they can cause priority inversions. This should be the case where the work is being put into a common workqueue losing our priority information and so being executed in FIFO from the worker, denying us the opportunity to reorder the requests afterwards. Signed-off-by:
-
José Roberto de Souza authored
This parameter is meant to be used when PSR issues are found as some issues in the past was due wrong values set in VBT so this would be a quick and easy way to ask users or for us to check if the issue is due VBT values. Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Signed-off-by:
-
- 04 Jun, 2020 15 commits
-
-
José Roberto de Souza authored
RKL doesn't have PSR2 HW tracking, it was replaced by software/manual tracking. The driver is required to track the areas that needs update and program hardware to send selective updates. So until the software tracking is implemented, PSR2 needs to be disabled for platforms without PSR2 HW tracking. BSpec: 50422 BSpec: 50424 Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-15-matthew.d.roper@intel.com
-
Matt Roper authored
There are a couple places in our driver that loop over transcoders A..D for gen11+; since RKL only has three pipes/transcoders, this can lead to unclaimed register reads/writes. We should add checks for transcoder existence where appropriate. v2: Move one transcoder check that wound up in the wrong function after conflict resolution. It belongs in bdw_get_trans_port_sync_config rather than bxt_get_dsi_transcoder_state. v3: Switch loops to use for_each_cpu_transcoder_masked() since this iterator already checks the platform's transcoder mask for us. (Ville) Cc: Aditya Swarup <aditya.swarup@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: -
Matt Roper authored
RKL uses DDI's A, B, TC1, and TC2 which need to map to combo PHY's A-D. Bspec: 49181 Cc: Imre Deak <imre.deak@intel.com> Cc: Aditya Swarup <aditya.swarup@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by:
-
José Roberto de Souza authored
As latest update we have now 2 voltage swing tables for DP over DKL PHY with only one difference in Level 0 pre-emphasis 3. So with 2 tables for DP is time to have one single function to return all DKL voltage swing tables. BSpec: 49292 Cc: Khaled Almahallawy <khaled.almahallawy@intel.com> Signed-off-by:
Khaled Almahallawy <khaled.almahallawy@intel.com> Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200602205424.138143-1-jose.souza@intel.com
-
Stanislav Lisovskiy authored
Previous patch didn't take into account all pipes but only those in state, which could cause wrong CDCLK conclcusions and calculations. Also there was a severe issue with min_cdclk being assigned to 0 every compare cycle. Too bad this was found by me only after merge. This could be also causing the issues in test, however not clear - anyway marking this as fixing the "Adjust CDCLK accordingly to our DBuf bw needs". v2: - s/pipe/crtc->pipe/ - save a bit of instructions by skipping inactive pipes, without getting 0 DBuf slice mask for it. Signed-off-by:Manasi Navare <manasi.d.navare@intel.com> Signed-off-by:
-
Matt Roper authored
Certain combo PHYs act as a compensation master to other PHYs and need to be initialized with a special irefgen bit in the PORT_COMP_DW8 register. Previously PHY A was the only compensation master (for PHYs B & C), but RKL adds a fourth PHY which is slaved to PHY C instead. Bspec: 49291 Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Aditya Swarup <aditya.swarup@intel.com> Signed-off-by:
Anusha Srivatsa <anusha.srivatsa@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-12-matthew.d.roper@intel.com
-
Matt Roper authored
The pin mapping for the final two outputs varies according to which PCH is present on the platform: with TGP the pins are remapped into the TC range, whereas with CMP they stay in the traditional combo output range. Bspec: 49181 Cc: Aditya Swarup <aditya.swarup@intel.com> Signed-off-by:
-
Lucas De Marchi authored
RKL uses the DDI A, DDI B, DDI USBC1, DDI USBC2 from the DE point of view, so all DDI/pipe/transcoder register use these indexes to refer to them. Combo phy and IO functions follow another namespace that we keep as "enum phy". The VBT in theory would use the DE point of view, but that does not happen in practice. Provide a table to convert the child devices to the "correct" port numbering we use. Now this is the output we get while reading the VBT: DDIA: [drm:intel_bios_port_aux_ch [i915]] using AUX A for port A (VBT) [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:275:DDI A] [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:275:DDI A] [drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x1 for port A (VBT) DDIB: [drm:intel_bios_port_aux_ch [i915]] using AUX B for port B (platform default) [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:291:DDI B] [drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x2 for port B (VBT) DDI USBC1: [drm:intel_bios_port_aux_ch [i915]] using AUX D for port D (VBT) [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:295:DDI D] [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:295:DDI D] [drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x3 for port D (VBT) DDI USBC2: [drm:intel_bios_port_aux_ch [i915]] using AUX E for port E (VBT) [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:306:DDI E] [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:306:DDI E] [drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x9 for port E (VBT) Cc: Clinton Taylor <Clinton.A.Taylor@intel.com> Cc: Aditya Swarup <aditya.swarup@intel.com> Signed-off-by:
Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by:
-
Matt Roper authored
Although we properly captured RKL's three pipes in the device info structure, we forgot to make the corresponding update to the transcoder mask. Set this field so that our transcoder loops will operate properly. Fixes: 123f62de ("drm/i915/rkl: Add RKL platform info and PCI ids") Signed-off-by:
-
Chris Wilson authored
Sometimes an engine might need to keep forcewake active while it is busy submitting requests for a particular workaround. Track such nuisance with engine->fw_domain. Signed-off-by:
-
Chris Wilson authored
Use the plain msec_to_jiffies() rather than the _timeout variant so we round down and do not add an extra jiffy to our interval. For example, with timeslicing we do not want to err on the longer side as any fairness depends on catching hogging contexts on the GPU. Bring on CFS. Signed-off-by:
-
Chris Wilson authored
If the execbuf is interrupted after building the cmdparser pipeline, and before we commit to submitting the request to HW, we would attempt to clean up the cmdparser early. While we held active references to the vma being parsed and constructed, we did not hold an active reference for the buffer pool itself. The result was that an interrupted execbuf could still have run the cmdparser pipeline, but since the buffer pool was idle, its target vma could have been recycled. Note this problem only occurs if the cmdparser is running async due to pipelined waits on busy fences, and the execbuf is interrupted. Fixes: 686c7c35 ("drm/i915/gem: Asynchronous cmdparser") Fixes: 16e87459 ("drm/i915/gt: Move the batch buffer pool from the engine to the gt") Signed-off-by:
-
Clint Taylor authored
Set GS Timer to 224. Combine with Wa_1604555607 due to register FF_MODE2 not being able to be read. V2: Math issue fixed Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Caz Yokoyama <caz.yokoyama@intel.com> Cc: Matt Atwood <matthew.s.atwood@intel.com> Signed-off-by:
Clint Taylor <clinton.a.taylor@intel.com> Acked-by:
-
Chris Wilson authored
Just to remove an obnoxious HAS_ENGINES(), and in the process make the code agnostic to the availabilty of any particular engine by making it exercise any and all such engines declared on the system. Signed-off-by:
-
Jani Nikula authored
The reset member in i915_params was previously changed to unsigned, but this failed to change the actual module parameter. Fixes: aae970d8 ("drm/i915: Mark i915.reset as unsigned") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by:
-
- 03 Jun, 2020 8 commits
-
-
Ville Syrjälä authored
Use max() instead of hand rolling it. Signed-off-by:
-
Ville Syrjälä authored
The DP spec says: "When the combination of the requested pre-emphasis level and voltage swing exceeds the capability of a DPTX, the DPTX shall set the pre-emphasis level according to the request and use the highest voltage swing it can output with the given pre-emphasis level." and "When a DPTX reads a request beyond the limits of this Standard, the DPTX shall set the pre-emphasis level according to the request and set the highest voltage swing level it can output with the given pre-emphasis level. If a DPTX is requested for 9.5dB of pre-emphasis level (may be supported for a DPTX) and cannot support that level, it shall set the pre-emphasis level to the next highest level, 6dB." Ie. we should first validate the pre-emphasis, and then select the appropriate vswing for it. Signed-off-by:
-
Ville Syrjälä authored
Different platforms have different max vswing/preemph settings. Turn that into a pair vfuncs so we can decouple intel_dp.c and intel_ddi.c further. Signed-off-by:
-
Ville Syrjälä authored
According to the DP spec supporting vswing 1 + preemph 2 is mandatory. We don't have the hw settings for that though. In order to pretend to follow the DP spec let's just select vswing 0 + preemph 2 in this case (the DP spec says to use the requested preemph in preference to the vswing when the requested values aren't supported). Signed-off-by:
-
Ville Syrjälä authored
IBX supports vswing level 3 and pre-emphasis level 3. Don't limit it to level 2 for those. Signed-off-by:
-
Ville Syrjälä authored
cpt/ppt support pre-emphasis level 3. Let's actually declare support for it, instead of clamping things to level 2. Also tweak the if-ladder in intel_dp_voltage_max() to match intel_dp_pre_emphasis_max() to make it easier to compare them. Signed-off-by:
-
Chris Wilson authored
We infrequently use the direct i915 backpointer from the i915_request, so do we really need to waste the space in the struct for it? 8 bytes from the most frequently allocated struct vs an 3 bytes and pointer chasing in using rq->engine->i915? Signed-off-by:
Akeem G Abodunrin <akeem.g.abodunrin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200602220953.21178-1-chris@chris-wilson.co.uk
-
Chris Wilson authored
If we injected an error (such as pretending the GuC firmware was broken), then suppress the error message as it is expected and our CI complains if it sees any *ERROR*. Signed-off-by:
-
- 02 Jun, 2020 2 commits
-
-
Chris Wilson authored
For reasons that be, the HW only allows usersace to read its own CTX_TIMESTAMP [context local HW runtime] on rcs. Make it available for all by adding it to the whitelists. v2: The change took effect from Cometlake. Signed-off-by:
-
Chris Wilson authored
Cometlake is a small refresh of Coffeelake, but since we have found out a difference in the plaforms, we need to identify them as separate platforms. Since we previously took Coffeelake/Cometlake as identical, update all IS_COFFEELAKE() to also include IS_COMETLAKE(). Signed-off-by:
-
