The 'struct sh_eth_cpu_data' field indicating the "intelligent checksum"
support was misnamed 'hw_crc' -- rename it to 'hw_checksum'.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After checking all  the available manuals,  I have enough information to
conclude  that the 'shift_rd0' flag is only relevant  for the Ether cores
supporting so called "intelligent checksum" (and hence having CSMR) which
is indicated  by the 'hw_crc' flag.  Since  all the relevant SoCs now have
both these flags set, we can  at last  get  rid of the former flag...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While in RUNNING state, phy_state_machine() checks for link changes by
comparing phydev->link before and after calling phy_read_status().
This works as long as it is guaranteed that phydev->link is never
changed outside the phy_state_machine().

If in some setups this happens, it causes the state machine to miss
a link loss and remain RUNNING despite phydev->link being 0.

This has been observed running a dsa setup with a process continuously
polling the link states over ethtool each second (SNMPD RFC-1213
agent). Disconnecting the link on a phy followed by a ETHTOOL_GSET
causes dsa_slave_get_settings() / dsa_slave_get_link_ksettings() to
call phy_read_status() and with that modify the link status - and
with that bricking the phy state machine.

This patch adds a fail-safe check while in RUNNING, which causes to
move to CHANGELINK when the link is gone and we are still RUNNING.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix dumping of nft_quota entries, from Pablo Neira Ayuso.

 2) Fix out of bounds access in nf_tables discovered by KASAN, from
    Florian Westphal.

 3) Fix IRQ enabling in dp83867 driver, from Grygorii Strashko.

 4) Fix unicast filtering in be2net driver, from Ivan Vecera.

 5) tg3_get_stats64() can race with driver close and ethtool
    reconfigurations, fix from Michael Chan.

 6) Fix error handling when pass limit is reached in bpf code gen on
    x86. From Daniel Borkmann.

 7) Don't clobber switch ops and use proper MDIO nested reads and writes
    in bcm_sf2 driver, from Florian Fainelli.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
  net: dsa: bcm_sf2: Utilize nested MDIO read/write
  net: dsa: bcm_sf2: Do not clobber b53_switch_ops
  net: stmmac: fix maxmtu assignment to be within valid range
  bpf: change back to orig prog on too many passes
  tg3: Fix race condition in tg3_get_stats64().
  be2net: fix unicast list filling
  be2net: fix accesses to unicast list
  netlabel: add CALIPSO to the list of built-in protocols
  vti6: fix device register to report IFLA_INFO_KIND
  net: phy: dp83867: fix irq generation
  amd-xgbe: Fix IRQ processing when running in single IRQ mode
  sh_eth: R8A7740 supports packet shecksumming
  sh_eth: fix EESIPR values for SH77{34|63}
  r8169: fix the typo in the comment
  nl80211: fix sched scan netlink socket owner destruction
  bridge: netfilter: Fix dropping packets that moving through bridge interface
  netfilter: ipt_CLUSTERIP: check duplicate config when initializing
  netfilter: nft_payload: mangle ckecksum if NFT_PAYLOAD_L4CSUM_PSEUDOHDR is set
  netfilter: nf_tables: fix oob access
  netfilter: nft_queue: use raw_smp_processor_id()
  ...

Joao Pinto says:

====================
adding new glue driver dwmac-dwc-qos-eth

This patch set contains the porting of the synopsys/dwc_eth_qos.c driver
to the stmmac structure. This operation resulted in the creation of a new
platform glue driver called dwmac-dwc-qos-eth which was based in the
dwc_eth_qos as is.

dwmac-dwc-qos-eth inherited dwc_eth_qos DT bindings, to assure that current
and old users can continue to use it as before. We can see this driver as
being deprecated, since all new development will be done in stmmac.

Please check each patch for implementation details.
====================
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new glue driver called dwmac-dwc-qos-eth which
was based in the dwc_eth_qos as is. To assure retro-compatibility a slight
tweak was also added to stmmac_platform.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to the
plat_stmmacenet_data structure. It also moves these platform variables
initialization to stmmac_platform. This was done for two reasons:

a) If PCI is used, platform related code is being executed in stmmac_main
resulting in warnings that have no sense and conceptually was not right

b) stmmac as a synopsys reference ethernet driver stack will be hosting
more and more drivers to its structure like synopsys/dwc_eth_qos.c.
These drivers have their own DT bindings that are not compatible with
stmmac's. One of the most important are the clock names, and so they need
to be parsed in the glue logic and initialized there, and that is the main
reason why the clocks were passed to the platform structure.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new parameter to the stmmac DT: snps,en-tx-lpi-clockgating.
It was ported from synopsys/dwc_eth_qos.c and it is useful if lpi tx clock
gating is needed by stmmac users also.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Reviewed-by: Lars Persson <larper@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code to handle rx checksumming was in the driver since its introduction
but for reasons unknown the feature flag was left out. Now it is possible
to enable this feature with ethtool.

Tested on my AR8161 ethernet card, there are no regressions observed in
netperf if this feature is enabled.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Davide Caratti says:

====================
net/sched: act_csum: add support for SCTP checksum

This series extends current act_csum functionality to allow computation of
SCTP checksums. Patch 1 ensures LIBCRC32C will be selected if NET_ACT_CSUM
is selected. Patch 2 extends act_csum to handle IPPROTO_SCTP protocol in
IPv4/IPv6 header, and eventually compute the CRC32c value.

v2:
- style fix in tc_csum.h
- avoid nested if statement in act_csum.c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

modify act_csum to compute crc32c on IPv4/IPv6 packets having SCTP in
their payload, and extend UAPI definitions accordingly.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LIBCRC32C is needed to compute crc32c on SCTP packets.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: small driver update

This patchset contains various small "non-net" fixes and enhancements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

As ENOTSUPP is specific to NFS, change the return error value to
EOPNOTSUPP in various places in the mlxsw driver.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the order of the free directives to match the port init function
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the mlxsw spectrum driver only supports offloading the matchall
classifier together with the mirred action. To allow more matchall tc
offloads, make the code symmetric so that it can be easily extended later
on for other actions.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Probably some copy-paste error from "int_msix" that caused "int_" prefix to
appear in the comments for all "eq_" APIs.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "err" variable is been checked, return always 0.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow to set number of descs close to possible values. In case of
minimum limit it's equal to number of channels to be able to set
at least one desc per channel. For maximum limit leave enough descs
number for tx channels.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This struct member is already initialized to zero upon root_ht's
allocation via kzalloc().
Signed-off-by: Alexandru Moise <00moses.alexander00@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jason A. Donenfeld says:

====================
Introduce The SipHash PRF

This patch series introduces SipHash into the kernel. SipHash is a
cryptographically secure PRF, which serves a variety of functions, and is
introduced in patch #1. The following patch #2 introduces HalfSipHash,
an optimization suitable for hash tables only. Finally, the last two patches
in this series show two usages of the introduced siphash function family.
It is expected that after this initial introduction, other usages will follow.

Please read the extensive descriptions in patch #1 and patch #2 of what these
functions do and the various levels of assurances. They're products of intense
cryptographic research, and I believe they're suitable for the uses outlined
herein.

The use of SipHash is not limited to the networking subsystem -- indeed I
would like to use it in other places too in the kernel. But after discussing
with a few on this list and at Linus' suggestion, the initial import of these
functions is coming through the networking tree. After these are merged, it
will then be easier to expand use elsewhere.

Changes v2->v3:
  - hsiphash keys now simply use an unsigned long, in order to avoid
    a cluttered ifdef and make it a bit more clear what's happening.
  - A typo in the documentation has been fixed.
  - The documentation has been augmented with an example relating to struct
    packing and passing.
  - The net_secret variable is now __read_mostly.

Hopefully this is the last of the required revisions, and v3 can be merged
into net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

SHA1 is slower and less secure than SipHash, and so replacing syncookie
generation with SipHash makes natural sense. Some BSDs have been doing
this for several years in fact.

The speedup should be similar -- and even more impressive -- to the
speedup from the sequence number fix in this series.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This gives a clear speed and security improvement. Siphash is both
faster and is more solid crypto than the aging MD5.

Rather than manually filling MD5 buffers, for IPv6, we simply create
a layout by a simple anonymous struct, for which gcc generates
rather efficient code. For IPv4, we pass the values directly to the
short input convenience functions.

64-bit x86_64:
[    1.683628] secure_tcpv6_sequence_number_md5# cycles: 99563527
[    1.717350] secure_tcp_sequence_number_md5# cycles: 92890502
[    1.741968] secure_tcpv6_sequence_number_siphash# cycles: 67825362
[    1.762048] secure_tcp_sequence_number_siphash# cycles: 67485526

32-bit x86:
[    1.600012] secure_tcpv6_sequence_number_md5# cycles: 103227892
[    1.634219] secure_tcp_sequence_number_md5# cycles: 94732544
[    1.669102] secure_tcpv6_sequence_number_siphash# cycles: 96299384
[    1.700165] secure_tcp_sequence_number_siphash# cycles: 86015473
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Miller <davem@davemloft.net>
Cc: David Laight <David.Laight@aculab.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HalfSipHash, or hsiphash, is a shortened version of SipHash, which
generates 32-bit outputs using a weaker 64-bit key. It has *much* lower
security margins, and shouldn't be used for anything too sensitive, but
it could be used as a hashtable key function replacement, if the output
is never exposed, and if the security requirement is not too high.

The goal is to make this something that performance-critical jhash users
would be willing to use.

On 64-bit machines, HalfSipHash1-3 is slower than SipHash1-3, so we alias
SipHash1-3 to HalfSipHash1-3 on those systems.

64-bit x86_64:
[    0.509409] test_siphash:     SipHash2-4 cycles: 4049181
[    0.510650] test_siphash:     SipHash1-3 cycles: 2512884
[    0.512205] test_siphash: HalfSipHash1-3 cycles: 3429920
[    0.512904] test_siphash:    JenkinsHash cycles:  978267
So, we map hsiphash() -> SipHash1-3

32-bit x86:
[    0.509868] test_siphash:     SipHash2-4 cycles: 14812892
[    0.513601] test_siphash:     SipHash1-3 cycles:  9510710
[    0.515263] test_siphash: HalfSipHash1-3 cycles:  3856157
[    0.515952] test_siphash:    JenkinsHash cycles:  1148567
So, we map hsiphash() -> HalfSipHash1-3

hsiphash() is roughly 3 times slower than jhash(), but comes with a
considerable security improvement.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jean-Philippe Aumasson <jeanphilippe.aumasson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SipHash is a 64-bit keyed hash function that is actually a
cryptographically secure PRF, like HMAC. Except SipHash is super fast,
and is meant to be used as a hashtable keyed lookup function, or as a
general PRF for short input use cases, such as sequence numbers or RNG
chaining.

For the first usage:

There are a variety of attacks known as "hashtable poisoning" in which an
attacker forms some data such that the hash of that data will be the
same, and then preceeds to fill up all entries of a hashbucket. This is
a realistic and well-known denial-of-service vector. Currently
hashtables use jhash, which is fast but not secure, and some kind of
rotating key scheme (or none at all, which isn't good). SipHash is meant
as a replacement for jhash in these cases.

There are a modicum of places in the kernel that are vulnerable to
hashtable poisoning attacks, either via userspace vectors or network
vectors, and there's not a reliable mechanism inside the kernel at the
moment to fix it. The first step toward fixing these issues is actually
getting a secure primitive into the kernel for developers to use. Then
we can, bit by bit, port things over to it as deemed appropriate.

While SipHash is extremely fast for a cryptographically secure function,
it is likely a bit slower than the insecure jhash, and so replacements
will be evaluated on a case-by-case basis based on whether or not the
difference in speed is negligible and whether or not the current jhash usage
poses a real security risk.

For the second usage:

A few places in the kernel are using MD5 or SHA1 for creating secure
sequence numbers, syn cookies, port numbers, or fast random numbers.
SipHash is a faster and more fitting, and more secure replacement for MD5
in those situations. Replacing MD5 and SHA1 with SipHash for these uses is
obvious and straight-forward, and so is submitted along with this patch
series. There shouldn't be much of a debate over its efficacy.

Dozens of languages are already using this internally for their hash
tables and PRFs. Some of the BSDs already use this in their kernels.
SipHash is a widely known high-speed solution to a widely known set of
problems, and it's time we catch-up.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jean-Philippe Aumasson <jeanphilippe.aumasson@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric Biggers <ebiggers3@gmail.com>
Cc: David Laight <David.Laight@aculab.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nothing about the route lookup requires bottom half to be disabled.
Remove the local_bh_disable ... local_bh_enable around ip_route_input.
This appears to be a vestige of days gone by as it has been there
since the beginning of git time.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sock_init() call it but not check it's return value,
so change it to void return and add an internal BUG_ON() check.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: bcm_sf2: Couple fixes

Here are a couple of fixes for bcm_sf2, please queue these up for -stable
as well, thank you very much!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We are implementing a MDIO bus which is behind another one, so use the
nested version of the accessors to get lockdep annotations correct.

Fixes: 461cd1b0 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.

Fixes: f458995b ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Willem de Bruijn says:

====================
convert tc_verd to integer bitfields

The skb tc_verd field takes up two bytes but uses far fewer bits.
Convert the remaining use cases to bitfields that fit in existing
holes (depending on config options) and potentially save the two
bytes in struct sk_buff.

This patchset is based on an earlier set by Florian Westphal and its
discussion (http://www.spinics.net/lists/netdev/msg329181.html).

Patches 1 and 2 are low hanging fruit: removing the last traces of
  data that are no longer stored in tc_verd.

Patches 3 and 4 convert tc_verd to individual bitfields (5 bits).

Patch 5 reduces TC_AT to a single bitfield,
  as AT_STACK is not valid here (unlike in the case of TC_FROM).

Patch 6 changes TC_FROM to two bitfields with clearly defined purpose.

It may be possible to reduce storage further after this initial round.
If tc_skip_classify is set only by IFB, testing skb_iif may suffice.
The L2 header pushing/popping logic can perhaps be shared with
AF_PACKET, which currently not pkt_type for the same purpose.

Changes:
  RFC -> v1
    - (patch 3): remove no longer needed label in tfc_action_exec
    - (patch 5): set tc_at_ingress at the same points as existing
                 SET_TC_AT calls

Tested ingress mirred + netem + ifb:

  ip link set dev ifb0 up
  tc qdisc add dev eth0 ingress
  tc filter add dev eth0 parent ffff: \
    u32 match ip dport 8000 0xffff \
    action mirred egress redirect dev ifb0
  tc qdisc add dev ifb0 root netem delay 1000ms
  nc -u -l 8000 &
  ssh $otherhost nc -u $host 8000

Tested egress mirred:

  ip link add veth1 type veth peer name veth2
  ip link set dev veth1 up
  ip link set dev veth2 up
  tcpdump -n -i veth2 udp and dst port 8000 &

  tc qdisc add dev eth0 root handle 1: prio
  tc filter add dev eth0 parent 1:0 \
    u32 match ip dport 8000 0xffff \
    action mirred egress redirect dev veth1
  tc qdisc add dev veth1 root netem delay 1000ms
  nc -u $otherhost 8000

Tested ingress mirred:

  ip link add veth1 type veth peer name veth2
  ip link add veth3 type veth peer name veth4

  ip netns add ns0
  ip netns add ns1

  for i in 1 2 3 4; do \
    NS=ns$((${i}%2)); \
    ip link set dev veth${i} netns ${NS}; \
    ip netns exec ${NS} \
      ip addr add dev veth${i} 192.168.1.${i}/24; \
    ip netns exec ${NS} \
      ip link set dev veth${i} up; \
  done

  ip netns exec ns0 tc qdisc add dev veth2 ingress
  ip netns exec ns0 \
    tc filter add dev veth2 parent ffff: \
      u32 match ip dport 8000 0xffff \
      action mirred ingress redirect dev veth4

  ip netns exec ns0 \
    tcpdump -n -i veth4 udp and dst port 8000 &
  ip netns exec ns1 \
    nc -u 192.168.1.2 8000
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The tc_from field fulfills two roles. It encodes whether a packet was
redirected by an act_mirred device and, if so, whether act_mirred was
called on ingress or egress. Split it into separate fields.

The information is needed by the special IFB loop, where packets are
taken out of the normal path by act_mirred, forwarded to IFB, then
reinjected at their original location (ingress or egress) by IFB.

The IFB device cannot use skb->tc_at_ingress, because that may have
been overwritten as the packet travels from act_mirred to ifb_xmit,
when it passes through tc_classify on the IFB egress path. Cache this
value in skb->tc_from_ingress.

That field is valid only if a packet arriving at ifb_xmit came from
act_mirred. Other packets can be crafted to reach ifb_xmit. These
must be dropped. Set tc_redirected on redirection and drop all packets
that do not have this bit set.

Both fields are set only on cloned skbs in tc actions, so original
packet sources do not have to clear the bit when reusing packets
(notably, pktgen and octeon).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Field tc_at is used only within tc actions to distinguish ingress from
egress processing. A single bit is sufficient for this purpose.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract the remaining two fields from tc_verd and remove the __u16
completely. TC_AT and TC_FROM are converted to equivalent two-bit
integer fields tc_at and tc_from. Where possible, use existing
helper skb_at_tc_ingress when reading tc_at. Introduce helper
skb_reset_tc to clear fields.

Not documenting tc_from and tc_at, because they will be replaced
with single bit fields in follow-on patches.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>