- 19 May, 2014 15 commits
-
-
Ajay Kumar authored
Add PWM backlight node for exynos5250 based snow board. Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Ajay Kumar authored
Adds the PWM nodes to 5250 pinctrl dtsi file. Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Vivek Gautam authored
Add required fixed-regulator for VBUS supply for USB 3.0 controller phy. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Vivek Gautam authored
Add required fixed-regulator for VBUS supply for USB 3.0 controller phy. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Vivek Gautam authored
Add required fixed-regulator for VBUS supply for USB 3.0 controller phy. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Sachin Kamat authored
PD entry was missing in MFC codec node. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Reviewed-by : Arun Kumar K <arun.kk@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Tushar Behera authored
The audio setup on Peach-pit board is similar to Snow board, hence the sound-card driver used on Snow board can be reused on Peach-pit board. Peach-pit board uses MAX98090 audio codec. Signed-off-by: Tushar Behera <tushar.behera@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Tushar Behera authored
The audio codec on Snow board, MAX98095 is connected on I2C7 bus. Also it requires the GPX1-7 line to be pulled up. Updated Snow DTS file to incorporate above changes and added a sound node to instantiate the I2S-based sound card. Signed-off-by: Tushar Behera <tushar.behera@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Vivek Gautam authored
Removing the dt node for older usb3 phy driver from Exynos5250 device tree and updating the dt node for DWC3 controller to use new phy driver based on generic phy framework. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Vivek Gautam authored
Add device tree node for new usbdrd-phy driver, which is based on generic phy framework. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Vivek Gautam authored
Add device tree nodes for DWC3 controller present on Exynos 5420 SoC, to enable support for USB 3.0. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Vivek Gautam authored
Add device tree nodes for USB 3.0 PHY present alongwith USB 3.0 controller Exynos 5420 SoC. This phy driver is based on generic phy framework. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Rahul Sharma authored
Enable hdmi for exynos5420 based peach-pit board. Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> Acked-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Rahul Sharma authored
Replace compatible string for HDMI node in Exynos5420. Since latest restructring in Drm hdmi driver, it is agreed to use a seperate compatible string for Exynos5420 HDMI IP siince it uses APB mapped Phy. Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> Acked-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Rahul Sharma authored
Enable support for HDMI for exynos5250 based Snow board. Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com> Acked-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
- 15 May, 2014 3 commits
-
-
Doug Anderson authored
Added TPS65090 regulator related nodes to Snow board. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Doug Anderson authored
Added pinctrl node for embedded controller (EC) IRQ on Snow board. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Doug Anderson authored
Added i2c-arbitrator pinctrl node to Snow board. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
- 14 May, 2014 2 commits
-
-
Sachin Kamat authored
Add SRAM binding documentation. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Tomasz Figa <t.figa@samsung.com> [kgene.kim@samsung.com: changed name SRAM to SYSRAM] Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Sachin Kamat authored
Instead of hardcoding the SYSRAM details for each SoC, pass this information through device tree (DT) and make the code SoC agnostic. Generic DT SRAM bindings are used for achieving this. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
- 08 May, 2014 7 commits
-
-
Arun Kumar K authored
Adds the google peach-pit board dts file which uses exynos5420 SoC. Signed-off-by: Arun Kumar K <arun.kk@samsung.com> Signed-off-by: Doug Anderson <dianders@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Arun Kumar K authored
Adding labels to nodes which do not have it yet in exynos5420. This is done so as to use reference based node updation in board files. Signed-off-by: Arun Kumar K <arun.kk@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Arun Kumar K authored
Adds the PWM nodes to 5420 pinctrl dtsi file. Signed-off-by: Arun Kumar K <arun.kk@samsung.com> Reviewed-by: Doug Anderson <dianders@chromium.org> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Sylwester Nawrocki authored
This patch enables the rear facing camera (s5c73m3) on TRATS2 board by adding the I2C0 bus controller, s5c73m3 sensor, MIPI CSI-2 receiver and the sensor's voltage regulator supply nodes. Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Sylwester Nawrocki authored
Remove unused /camera/clock-controller node and add required clock properties to the camera node. This is required for a clock provider that will be referenced by image sensor devices. Also add required clock related changes to s5k6a3 device node and afvdd regulator supply. Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Tomasz Stanislawski authored
The i2c_ak8975 controller uses label i2c8. This alias is already used for I2C controller 8 defined in file arch/arm/boot/dts/exynos4.dtsi. This patch renames a label for i2c_ak8975 to i2c9. Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
Tomasz Stanislawski authored
This patch adds missing pinctrls for I2C controllers 2-7. Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com> Reviewed-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-
- 13 Apr, 2014 12 commits
-
-
Linus Torvalds authored
-
Geert Uytterhoeven authored
Some versions of gcc even warn about it: mm/shmem.c: In function ‘shmem_file_aio_read’: mm/shmem.c:1414: warning: ‘error’ may be used uninitialized in this function If the loop is aborted during the first iteration by one of the two first break statements, error will be uninitialized. Introduced by commit 6e58e79d ("introduce copy_page_to_iter, kill loop over iovec in generic_file_aio_read()"). Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Geert Uytterhoeven authored
On 32 bit, size_t is "unsigned int", not "unsigned long", causing the following warning when comparing with PAGE_SIZE, which is always "unsigned long": fs/cifs/file.c: In function ‘cifs_readdata_to_iov’: fs/cifs/file.c:2757: warning: comparison of distinct pointer types lacks a cast Introduced by commit 7f25bba8 ("cifs_iovec_read: keep iov_iter between the calls of cifs_readdata_to_iov()"), which changed the signedness of "remaining" and the code from min_t() to min(). Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linuxLinus Torvalds authored
Pull slab changes from Pekka Enberg: "The biggest change is byte-sized freelist indices which reduces slab freelist memory usage: https://lkml.org/lkml/2013/12/2/64" * 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux: mm: slab/slub: use page->list consistently instead of page->lru mm/slab.c: cleanup outdated comments and unify variables naming slab: fix wrongly used macro slub: fix high order page allocation problem with __GFP_NOFAIL slab: Make allocations with GFP_ZERO slightly more efficient slab: make more slab management structure off the slab slab: introduce byte sized index for the freelist of a slab slab: restrict the number of objects in a slab slab: introduce helper functions to get/set free object slab: factor out calculate nr objects in cache_estimate
-
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuildLinus Torvalds authored
Pull misc kbuild changes from Michal Marek: "Here is the non-critical part of kbuild: - One bogus coccinelle check removed, one check fixed not to suggest the obsolete PTR_RET macro - scripts/tags.sh does not index the generated *.mod.c files - new objdiff tool to list differences between two versions of an object file - A fix for scripts/bootgraph.pl" * 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: scripts/coccinelle: Use PTR_ERR_OR_ZERO scripts/bootgraph.pl: Add graphic header scripts: objdiff: detect object code changes between two commits Coccicheck: Remove memcpy to struct assignment test scripts/tags.sh: Ignore *.mod.c
-
Mikulas Patocka authored
This patch fixes I/O errors with the sym53c8xx_2 driver when the disk returns QUEUE FULL status. When the controller encounters an error (including QUEUE FULL or BUSY status), it aborts all not yet submitted requests in the function sym_dequeue_from_squeue. This function aborts them with DID_SOFT_ERROR. If the disk has full tag queue, the request that caused the overflow is aborted with QUEUE FULL status (and the scsi midlayer properly retries it until it is accepted by the disk), but the sym53c8xx_2 driver aborts the following requests with DID_SOFT_ERROR --- for them, the midlayer does just a few retries and then signals the error up to sd. The result is that disk returning QUEUE FULL causes request failures. The error was reproduced on 53c895 with COMPAQ BD03685A24 disk (rebranded ST336607LC) with command queue 48 or 64 tags. The disk has 64 tags, but under some access patterns it return QUEUE FULL when there are less than 64 pending tags. The SCSI specification allows returning QUEUE FULL anytime and it is up to the host to retry. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Paul Mackerras authored
Commit 8f619b54 ("powerpc/ppc64: Do not turn AIL (reloc-on interrupts) too early") added code to set the AIL bit in the LPCR without checking whether the kernel is running in hypervisor mode. The result is that when the kernel is running as a guest (i.e., under PowerKVM or PowerVM), the processor takes a privileged instruction interrupt at that point, causing a panic. The visible result is that the kernel hangs after printing "returning from prom_init". This fixes it by checking for hypervisor mode being available before setting LPCR. If we are not in hypervisor mode, we enable relocation-on interrupts later in pSeries_setup_arch using the H_SET_MODE hcall. Signed-off-by: Paul Mackerras <paulus@samba.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Davidlohr Bueso authored
Commits 11d4616b ("futex: revert back to the explicit waiter counting code") and 69cd9eba ("futex: avoid race between requeue and wake") changed some of the finer details of how we think about futexes. One was a late fix and the other a consequence of overlooking the whole requeuing logic. The first change caused our documentation to be incorrect, and the second made us aware that we need to explicitly add more details to it. Signed-off-by: Davidlohr Bueso <davidlohr@hp.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull yet more networking updates from David Miller: 1) Various fixes to the new Redpine Signals wireless driver, from Fariya Fatima. 2) L2TP PPP connect code takes PMTU from the wrong socket, fix from Dmitry Petukhov. 3) UFO and TSO packets differ in whether they include the protocol header in gso_size, account for that in skb_gso_transport_seglen(). From Florian Westphal. 4) If VLAN untagging fails, we double free the SKB in the bridging output path. From Toshiaki Makita. 5) Several call sites of sk->sk_data_ready() were referencing an SKB just added to the socket receive queue in order to calculate the second argument via skb->len. This is dangerous because the moment the skb is added to the receive queue it can be consumed in another context and freed up. It turns out also that none of the sk->sk_data_ready() implementations even care about this second argument. So just kill it off and thus fix all these use-after-free bugs as a side effect. 6) Fix inverted test in tcp_v6_send_response(), from Lorenzo Colitti. 7) pktgen needs to do locking properly for LLTX devices, from Daniel Borkmann. 8) xen-netfront driver initializes TX array entries in RX loop :-) From Vincenzo Maffione. 9) After refactoring, some tunnel drivers allow a tunnel to be configured on top itself. Fix from Nicolas Dichtel. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits) vti: don't allow to add the same tunnel twice gre: don't allow to add the same tunnel twice drivers: net: xen-netfront: fix array initialization bug pktgen: be friendly to LLTX devices r8152: check RTL8152_UNPLUG net: sun4i-emac: add promiscuous support net/apne: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO net: ipv6: Fix oif in TCP SYN+ACK route lookup. drivers: net: cpsw: enable interrupts after napi enable and clearing previous interrupts drivers: net: cpsw: discard all packets received when interface is down net: Fix use after free by removing length arg from sk_data_ready callbacks. Drivers: net: hyperv: Address UDP checksum issues Drivers: net: hyperv: Negotiate suitable ndis version for offload support Drivers: net: hyperv: Allocate memory for all possible per-pecket information bridge: Fix double free and memory leak around br_allowed_ingress bonding: Remove debug_fs files when module init fails i40evf: program RSS LUT correctly i40evf: remove open-coded skb_cow_head ixgb: remove open-coded skb_cow_head igbvf: remove open-coded skb_cow_head ...
-
Linus Torvalds authored
Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux Pull blackfin updates from Steven Miao: "Code cleanup, some previously ignored patches, and bug fixes" * tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux: blackfin: cleanup board files bf609: clock: drop unused clock bit set/clear functions Blackfin: bf537: rename "CONFIG_ADT75" Blackfin: bf537: rename "CONFIG_AD7314" Blackfin: bf537: rename ad2s120x ->ad2s1200 blackfin: bf537: fix typo "CONFIG_SND_SOC_ADV80X_MODULE" blackfin: dma: current count mmr is read only bfin_crc: Move architecture independant crc header file out of the blackfin folder. bf54x: drop unuesd HOST status,control,timeout registers bit define macros blackfin: portmux: cleanup head file Blackfin: remove "config IP_CHECKSUM_L1" blackfin: Remove GENERIC_GPIO config option again blackfin:Use generic /proc/interrupts implementation blackfin: bf60x: fix typo "CONFIG_PM_BFIN_WAKE_PA15_POL"
-
Linus Torvalds authored
Merge tag 'remoteproc-3.15-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc Pull remoteproc cleanups from Ohad Ben-Cohen: "Several remoteproc cleanup patches coming from Jingoo Han, Julia Lawall and Uwe Kleine-König" * tag 'remoteproc-3.15-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc: remoteproc/ste_modem: staticize local symbols remoteproc/davinci: simplify use of devm_ioremap_resource remoteproc/davinci: drop needless devm_clk_put
-
git://git.linuxfoundation.org/llvmlinux/kernelLinus Torvalds authored
Pull llvm patches from Behan Webster: "These are some initial updates to support compiling the kernel with clang. These patches have been through the proper reviews to the best of my ability, and have been soaking in linux-next for a few weeks. These patches by themselves still do not completely allow clang to be used with the kernel code, but lay the foundation for other patches which are still under review. Several other of the LLVMLinux patches have been already added via maintainer trees" * tag 'llvmlinux-for-v3.15' of git://git.linuxfoundation.org/llvmlinux/kernel: x86: LLVMLinux: Fix "incomplete type const struct x86cpu_device_id" x86 kbuild: LLVMLinux: More cc-options added for clang x86, acpi: LLVMLinux: Remove nested functions from Thinkpad ACPI LLVMLinux: Add support for clang to compiler.h and new compiler-clang.h LLVMLinux: Remove warning about returning an uninitialized variable kbuild: LLVMLinux: Fix LINUX_COMPILER definition script for compilation with clang Documentation: LLVMLinux: Update Documentation/dontdiff kbuild: LLVMLinux: Adapt warnings for compilation with clang kbuild: LLVMLinux: Add Kbuild support for building kernel with Clang
-
- 12 Apr, 2014 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pendingLinus Torvalds authored
Pull SCSI target updates from Nicholas Bellinger: "Here are the target pending updates for v3.15-rc1. Apologies in advance for waiting until the second to last day of the merge window to send these out. The highlights this round include: - iser-target support for T10 PI (DIF) offloads (Sagi + Or) - Fix Task Aborted Status (TAS) handling in target-core (Alex Leung) - Pass in transport supported PI at session initialization (Sagi + MKP + nab) - Add WRITE_INSERT + READ_STRIP T10 PI support in target-core (nab + Sagi) - Fix iscsi-target ERL=2 ASYNC_EVENT connection pointer bug (nab) - Fix tcm_fc use-after-free of ft_tpg (Andy Grover) - Use correct ib_sg_dma primitives in ib_isert (Mike Marciniszyn) Also, note the virtio-scsi + vhost-scsi changes to expose T10 PI metadata into KVM guest have been left-out for now, as there where a few comments from MST + Paolo that where not able to be addressed in time for v3.15. Please expect this feature for v3.16-rc1" * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (43 commits) ib_srpt: Use correct ib_sg_dma primitives target/tcm_fc: Rename ft_tport_create to ft_tport_get target/tcm_fc: Rename ft_{add,del}_lport to {add,del}_wwn target/tcm_fc: Rename structs and list members for clarity target/tcm_fc: Limit to 1 TPG per wwn target/tcm_fc: Don't export ft_lport_list target/tcm_fc: Fix use-after-free of ft_tpg target: Add check to prevent Abort Task from aborting itself target: Enable READ_STRIP emulation in target_complete_ok_work target/sbc: Add sbc_dif_read_strip software emulation target: Enable WRITE_INSERT emulation in target_execute_cmd target/sbc: Add sbc_dif_generate software emulation target/sbc: Only expose PI read_cap16 bits when supported by fabric target/spc: Only expose PI mode page bits when supported by fabric target/spc: Only expose PI inquiry bits when supported by fabric target: Pass in transport supported PI at session initialization target/iblock: Fix double bioset_integrity_free bug Target/sbc: Initialize COMPARE_AND_WRITE write_sg scatterlist target/rd: T10-Dif: RAM disk is allocating more space than required. iscsi-target: Fix ERL=2 ASYNC_EVENT connection pointer bug ...
-