When a link endpoint is going down locally, e.g., because its interface
is being stopped, it will spontaneously send out a RESET message to
its peer, informing it about this fact. This saves the peer from
detecting the failure via probing, and hence gives both speedier and
less resource consuming failure detection on the peer side.

According to the link FSM, a receiver of a RESET message, ignoring the
reason for it, must now consider the sender ready to come back up, and
starts periodically sending out ACTIVATE messages to the peer in order
to re-establish the link. Also, according to the FSM, the receiver of
an ACTIVATE message can now go directly to state ESTABLISHED and start
sending regular traffic packets. This is a well-proven and robust FSM.

However, in the case of a reboot, there is a small possibilty that link
endpoint on the rebooted node may have been re-created with a new bearer
identity between the moment it sent its (pre-boot) RESET and the moment
it receives the ACTIVATE from the peer. The new bearer identity cannot
be known by the peer according to this scenario, since traffic headers
don't convey such information. This is a problem, because both endpoints
need to know the correct value of the peer's bearer id at any moment in
time in order to be able to produce correct link events for their users.

The only way to guarantee this is to enforce a full setup message
exchange (RESET + ACTIVATE) even after the reboot, since those messages
carry the bearer idientity in their header.

In this commit we do this by introducing and setting a "stopping" bit in
the header of the spontaneously generated RESET messages, informing the
peer that the sender will not be immediately ready to re-establish the
link. A receiver seeing this bit must act as if this were a locally
detected connectivity failure, and hence has to go through a full two-
way setup message exchange before any link can be re-established.

Although never reported, this problem seems to have always been around.

This protocol addition is fully backwards compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: spectrum_buffers: couple of cosmetic patches

As suggested by David Laight
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: bf797471 ("devlink: add shared buffer configuration")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the tun device accounting uses dev->stats without applying any
kind of protection, regardless that accounting happens in preemptible
process context.
This patch move the tun stats to a per cpu data structure, and protect
the updates with  u64_stats_update_begin()/u64_stats_update_end() or
this_cpu_inc according to the stat type. The per cpu stats are
aggregated by the newly added ndo_get_stats64 ops.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bpf-ARG_PTR_TO_RAW_STACK'

Daniel Borkmann says:

====================
BPF updates

This series adds a new verifier argument type called
ARG_PTR_TO_RAW_STACK and converts related helpers to make
use of it. Basic idea is that we can save init of stack
memory when the helper function is guaranteed to fully
fill out the passed buffer in every path. Series also adds
test cases and converts samples. For more details, please
see individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds test cases mostly around ARG_PTR_TO_RAW_STACK to check the
verifier behaviour.

  [...]
  #84 raw_stack: no skb_load_bytes OK
  #85 raw_stack: skb_load_bytes, no init OK
  #86 raw_stack: skb_load_bytes, init OK
  #87 raw_stack: skb_load_bytes, spilled regs around bounds OK
  #88 raw_stack: skb_load_bytes, spilled regs corruption OK
  #89 raw_stack: skb_load_bytes, spilled regs corruption 2 OK
  #90 raw_stack: skb_load_bytes, spilled regs + data OK
  #91 raw_stack: skb_load_bytes, invalid access 1 OK
  #92 raw_stack: skb_load_bytes, invalid access 2 OK
  #93 raw_stack: skb_load_bytes, invalid access 3 OK
  #94 raw_stack: skb_load_bytes, invalid access 4 OK
  #95 raw_stack: skb_load_bytes, invalid access 5 OK
  #96 raw_stack: skb_load_bytes, invalid access 6 OK
  #97 raw_stack: skb_load_bytes, large access OK
  Summary: 98 PASSED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the zero initialization in the sample programs where appropriate.
Note that this is an optimization which is now possible, old programs
still doing the zero initialization are just fine as well. Also, make
sure we don't have padding issues when we don't memset() the entire
struct anymore.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch converts all helpers that can use ARG_PTR_TO_RAW_STACK as argument
type. For tc programs this is bpf_skb_load_bytes(), bpf_skb_get_tunnel_key(),
bpf_skb_get_tunnel_opt(). For tracing, this optimizes bpf_get_current_comm()
and bpf_probe_read(). The check in bpf_skb_load_bytes() for MAX_BPF_STACK can
also be removed since the verifier already makes sure we stay within bounds
on stack buffers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When passing buffers from eBPF stack space into a helper function, we have
ARG_PTR_TO_STACK argument type for helpers available. The verifier makes sure
that such buffers are initialized, within boundaries, etc.

However, the downside with this is that we have a couple of helper functions
such as bpf_skb_load_bytes() that fill out the passed buffer in the expected
success case anyway, so zero initializing them prior to the helper call is
unneeded/wasted instructions in the eBPF program that can be avoided.

Therefore, add a new helper function argument type called ARG_PTR_TO_RAW_STACK.
The idea is to skip the STACK_MISC check in check_stack_boundary() and color
the related stack slots as STACK_MISC after we checked all call arguments.

Helper functions using ARG_PTR_TO_RAW_STACK must make sure that every path of
the helper function will fill the provided buffer area, so that we cannot leak
any uninitialized stack memory. This f.e. means that error paths need to
memset() the buffers, but the expected fast-path doesn't have to do this
anymore.

Since there's no such helper needing more than at most one ARG_PTR_TO_RAW_STACK
argument, we can keep it simple and don't need to check for multiple areas.
Should in future such a use-case really appear, we have check_raw_mode() that
will make sure we implement support for it first.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when the verifier checks calls in check_call() function, we
call check_func_arg() for all 5 arguments e.g. to make sure expected types
are correct. In some cases, we collect meta data (here: map pointer) to
perform additional checks such as checking stack boundary on key/value
sizes for subsequent arguments. As we're going to extend the meta data,
add a generic struct bpf_call_arg_meta that we can use for passing into
check_func_arg().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds what's missing to properly support RPS and RFS on SCTP,
as some of it is already implemented in common calls.

Having support for RPS and RFS allows better scaling specially because
not all NICs support hashing SCTP headers.

Save the hash right when we dequeue a skb from inqueue so we do it only
once per skb instead of per chunk. New sockets will then inherit the
hash through sctp_copy_sock().
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skbs given to validate_xmit_skb() should not have a next
pointer anymore.

Also if a packet is dropped, increment dev->tx_dropped
__dev_queue_xmit() no longer has to change tx_dropped in this case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

consume_skb() isn't for error cases that kfree_skb() is more proper
one.  At this patch, it fixed tpacket_rcv() and packet_rcv() to be
consistent for error or non-error cases letting perf trace its event
properly.
Signed-off-by: Weongyo Jeong <weongyo.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Until now, the requests sent to topology server are queued
to a workqueue by the generic server framework.
These messages are processed by worker threads and trigger the
registered callbacks.
To reduce latency on uniprocessor systems, explicit rescheduling
is performed using cond_resched() after MAX_RECV_MSG_COUNT(25)
messages.

This implementation on SMP systems leads to an subscriber refcnt
error as described below:
When a worker thread yields by calling cond_resched() in a SMP
system, a new worker is created on another CPU to process the
pending workitem. Sometimes the sleeping thread wakes up before
the new thread finishes execution.
This breaks the assumption on ordering and being single threaded.
The fault is more frequent when MAX_RECV_MSG_COUNT is lowered.

If the first thread was processing subscription create and the
second thread processing close(), the close request will free
the subscriber and the create request oops as follows:

[31.224137] WARNING: CPU: 2 PID: 266 at include/linux/kref.h:46 tipc_subscrb_rcv_cb+0x317/0x380         [tipc]
[31.228143] CPU: 2 PID: 266 Comm: kworker/u8:1 Not tainted 4.5.0+ #97
[31.228377] Workqueue: tipc_rcv tipc_recv_work [tipc]
[...]
[31.228377] Call Trace:
[31.228377]  [<ffffffff812fbb6b>] dump_stack+0x4d/0x72
[31.228377]  [<ffffffff8105a311>] __warn+0xd1/0xf0
[31.228377]  [<ffffffff8105a3fd>] warn_slowpath_null+0x1d/0x20
[31.228377]  [<ffffffffa0098067>] tipc_subscrb_rcv_cb+0x317/0x380 [tipc]
[31.228377]  [<ffffffffa00a4984>] tipc_receive_from_sock+0xd4/0x130 [tipc]
[31.228377]  [<ffffffffa00a439b>] tipc_recv_work+0x2b/0x50 [tipc]
[31.228377]  [<ffffffff81071925>] process_one_work+0x145/0x3d0
[31.246554] ---[ end trace c3882c9baa05a4fd ]---
[31.248327] BUG: spinlock bad magic on CPU#2, kworker/u8:1/266
[31.249119] BUG: unable to handle kernel NULL pointer dereference at 0000000000000428
[31.249323] IP: [<ffffffff81099d0c>] spin_dump+0x5c/0xe0
[31.249323] PGD 0
[31.249323] Oops: 0000 [#1] SMP

In this commit, we
- rename tipc_conn_shutdown() to tipc_conn_release().
- move connection release callback execution from tipc_close_conn()
  to a new function tipc_sock_release(), which is executed before
  we free the connection.
Thus we release the subscriber during connection release procedure
rather than connection shutdown procedure.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
GRO Fixed IPv4 ID support and GSO partial support

This patch series sets up a few different things.

First it adds support for GRO of frames with a fixed IP ID value.  This
will allow us to perform GRO for frames that go through things like an IPv6
to IPv4 header translation.

The second item we add is support for segmenting frames that are generated
this way.  Most devices only support an incrementing IP ID value, and in
the case of TCP the IP ID can be ignored in many cases since the DF bit
should be set.  So we can technically segment these frames using existing
TSO if we are willing to allow the IP ID to be mangled.  As such I have
added a matching feature for the new form of GRO/GSO called TCP IPv4 ID
mangling.  With this enabled we can assemble and disassemble a frame with
the sequence number fixed and the only ill effect will be that the IPv4 ID
will be altered which may or may not have any noticeable effect.  As such I
have defaulted the feature to disabled.

The third item this patch series adds is support for partial GSO
segmentation.  Partial GSO segmentation allows us to split a large frame
into two pieces.  The first piece will have an even multiple of MSS worth
of data and the headers before the one pointed to by csum_start will have
been updated so that they are correct for if the data payload had already
been segmented.  By doing this we can do things such as precompute the
outer header checksums for a frame to be segmented allowing us to perform
TSO on devices that don't support tunneling, or tunneling with outer header
checksums.

This patch set is based on the net-next tree, but I included "net: remove
netdevice gso_min_segs" in my tree as I assume it is likely to be applied
before this patch set will and I wanted to avoid a merge conflict.

v2: Fixed items reported by Jesse Gross
	fixed missing GSO flag in MPLS check
	adding DF check for MANGLEID
    Moved extra GSO feature checks into gso_features_check
    Rebased batches to account for "net: remove netdevice gso_min_segs"

Driver patches from the first patch set should still be compatible.  However
I do have a few changes in them so I will submit a v2 of those to Jeff
Kirsher once these patches are accepted into net-next.

Example driver patches for i40e, ixgbe, and igb:
https://patchwork.ozlabs.org/patch/608221/
https://patchwork.ozlabs.org/patch/608224/
https://patchwork.ozlabs.org/patch/608225/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This document is a starting point for defining the TSO and GSO features.
The whole thing is starting to get a bit messy so I wanted to make sure we
have notes somwhere to start describing what does and doesn't work.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for something I am referring to as GSO partial.
The basic idea is that we can support a broader range of devices for
segmentation if we use fixed outer headers and have the hardware only
really deal with segmenting the inner header.  The idea behind the naming
is due to the fact that everything before csum_start will be fixed headers,
and everything after will be the region that is handled by hardware.

With the current implementation it allows us to add support for the
following GSO types with an inner TSO_MANGLEID or TSO6 offload:
NETIF_F_GSO_GRE
NETIF_F_GSO_GRE_CSUM
NETIF_F_GSO_IPIP
NETIF_F_GSO_SIT
NETIF_F_UDP_TUNNEL
NETIF_F_UDP_TUNNEL_CSUM

In the case of hardware that already supports tunneling we may be able to
extend this further to support TSO_TCPV4 without TSO_MANGLEID if the
hardware can support updating inner IPv4 headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch does two things.

First it allows TCP to aggregate TCP frames with a fixed IPv4 ID field.  As
a result we should now be able to aggregate flows that were converted from
IPv6 to IPv4.  In addition this allows us more flexibility for future
implementations of segmentation as we may be able to use a fixed IP ID when
segmenting the flow.

The second thing this does is that it places limitations on the outer IPv4
ID header in the case of tunneled frames.  Specifically it forces the IP ID
to be incrementing by 1 unless the DF bit is set in the outer IPv4 header.
This way we can avoid creating overlapping series of IP IDs that could
possibly be fragmented if the frame goes through GRO and is then
resegmented via GSO.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for TSO using IPv4 headers with a fixed IP ID
field.  This is meant to allow us to do a lossless GRO in the case of TCP
flows that use a fixed IP ID such as those that convert IPv6 header to IPv4
headers.

In addition I am adding a feature that for now I am referring to TSO with
IP ID mangling.  Basically when this flag is enabled the device has the
option to either output the flow with incrementing IP IDs or with a fixed
IP ID regardless of what the original IP ID ordering was.  This is useful
in cases where the DF bit is set and we do not care if the original IP ID
value is maintained.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The strings were missing for several of the GSO offloads that are
available.  This patch provides the missing strings so that we can toggle
or query any of them via the ethtool command.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
devlink + mlxsw: add support for config and control of shared buffers

ASICs implement shared buffer for packet forwarding purposes and enable
flexible partitioning of the shared buffer for different flows and ports,
enabling non-blocking progress of different flows as well as separation
of lossy traffic from loss-less traffic when using Per-Priority Flow
Control (PFC). The shared buffer optimizes the buffer utilization for better
absorption of packet bursts.

This patchset implements API which is based on the model SAI uses. That is
aligned with multiple ASIC vendors so this API should be vendor neutral.

Userspace counterpart patchset for devlink iproute2 tool can be found here:
https://github.com/jpirko/iproute2_mlxsw/tree/devlink_sb

Couple of examples of usage:

switch$ devlink sb help
Usage: devlink sb show [ DEV [ sb SB_INDEX ] ]
       devlink sb pool show [ DEV [ sb SB_INDEX ] pool POOL_INDEX ]
       devlink sb pool set DEV [ sb SB_INDEX ] pool POOL_INDEX
                           size POOL_SIZE thtype { static | dynamic }
       devlink sb port pool show [ DEV/PORT_INDEX [ sb SB_INDEX ]
                                   pool POOL_INDEX ]
       devlink sb port pool set DEV/PORT_INDEX [ sb SB_INDEX ]
                                pool POOL_INDEX th THRESHOLD
       devlink sb tc bind show [ DEV/PORT_INDEX [ sb SB_INDEX ] tc TC_INDEX ]
       devlink sb tc bind set DEV/PORT_INDEX [ sb SB_INDEX ] tc TC_INDEX
                              type { ingress | egress } pool POOL_INDEX
                              th THRESHOLD
       devlink sb occupancy show { DEV | DEV/PORT_INDEX } [ sb SB_INDEX ]
       devlink sb occupancy snapshot DEV [ sb SB_INDEX ]
       devlink sb occupancy clearmax DEV [ sb SB_INDEX ]

switch$ devlink sb show
pci/0000:03:00.0: sb 0 size 16777216 ing_pools 4 eg_pools 4 ing_tcs 8 eg_tcs 8

switch$ devlink sb pool show
pci/0000:03:00.0: sb 0 pool 0 type ingress size 12400032 thtype dynamic
pci/0000:03:00.0: sb 0 pool 1 type ingress size 0 thtype dynamic
pci/0000:03:00.0: sb 0 pool 2 type ingress size 0 thtype dynamic
pci/0000:03:00.0: sb 0 pool 3 type ingress size 200064 thtype dynamic
pci/0000:03:00.0: sb 0 pool 4 type egress size 13220064 thtype dynamic
pci/0000:03:00.0: sb 0 pool 5 type egress size 0 thtype dynamic
pci/0000:03:00.0: sb 0 pool 6 type egress size 0 thtype dynamic
pci/0000:03:00.0: sb 0 pool 7 type egress size 0 thtype dynamic

switch$ devlink sb port pool show sw0p7 pool 0
sw0p7: sb 0 pool 0 threshold 16

switch$ sudo devlink sb port pool set sw0p7 pool 0 th 15

switch$ devlink sb port pool show sw0p7 pool 0
sw0p7: sb 0 pool 0 threshold 15

switch$ devlink sb tc bind show sw0p7 tc 0 type ingress
sw0p7: sb 0 tc 0 type ingress pool 0 threshold 10

switch$ sudo devlink sb tc bind set sw0p7 tc 0 type ingress pool 0 th 9

switch$ devlink sb tc bind show sw0p7 tc 0 type ingress
sw0p7: sb 0 tc 0 type ingress pool 0 threshold 9

switch$ sudo devlink sb occupancy snapshot pci/0000:03:00.0

switch$ devlink sb occupancy show sw0p7
sw0p7:
  pool: 0:      82944/3217344 1:          0/0       2:          0/0       3:          0/0
        4:          0/384     5:          0/0       6:          0/0       7:          0/0
  itc:  0(0):   96768/3217344 1(0):       0/0       2(0):       0/0       3(0):       0/0
        4(0):       0/0       5(0):       0/0       6(0):       0/0       7(0):       0/0
  etc:  0(4):       0/384     1(4):       0/0       2(4):       0/0       3(4):       0/0
        4(4):       0/0       5(4):       0/0       6(4):       0/0       7(4):       0/0

switch$ sudo devlink sb occupancy clearmax pci/0000:03:00.0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement occupancy API introduced in devlink and mlxsw core. This is
done by accessing SBPM register for Port-Pool and SBSR for Port-TC
current and max occupancy values. Max clear is implemented using the
same registers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far it was possible to have one EMAD register access at a time,
locked by mutex. This patch extends this interface to allow multiple
EMAD register accesses to be in fly at once. That allows faster
processing on firmware side avoiding unused time in between EMADs.
Measured speedup is ~30% for shared occupancy snapshot operation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follow-up patch is going to need to use delayed work as well and
frequently. The FDB notification processing is already using that and
also quite frequently. It makes sense to create separate workqueue just
for mlxsw driver in this case and do not pollute system_wq.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since it is not possible to get and clear Port-Pool occupancy data using
SBSR register, there's a need to implement that using SBPM.
Extend pack helper and add unpack helper to get occupancy values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This register allows to query HW for current and maximal buffer usage.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add middle layer in mlxsw core code to forward shared buffer occupancy
calls into specific ASIC drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement previously introduced mlxsw core shared buffer API.
For Spectrum, that is done utilizing registers SBPR, SBCM and SBPM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Needed in following patch.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Although the device supports max_buff magic values 0 and 0xff, these are
not exposed to the user via devlink.
Therefore, adjust the default values to be within configurable range.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As explained in commit ff6551ec ("mlxsw: spectrum: Correctly
configure headroom size") control packets are directed to priority group
buffer 9 (PG9) in the ports' headroom buffers.

Since we don't want to drop control packets in case they can't be
admitted to the switch's shared buffer we bind PG9 to a different
ingress pool from the one used by all other PGs.

Unlike other PGs, we currently don't expose the binding between PG9 to a
pool and leave it fixed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since there is no congestion control for CPU port traffic, we can change
the CPU port TC binding to pool 0 with min_buff and max_buff zeroed.
Remove initialization for pool egress pool 3 since it is no longer used
by dafault.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to achieve faster dumping of current setting and also in order
to provide possibility to get pool mode without a need to query hardware,
do cache the configuration in driver.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Be consintent with rest of the registers (pm, cm) and use "pr" here.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Structs are in arrays so use array index as pool/tc/prio index. With
that, there is need to maintain separate arrays for ingress and egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pushed them into helper functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add middle layer in mlxsw core code to forward shared buffer calls
into specific ASIC drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

User needs to monitor shared buffer occupancy. For that, he issues a
snapshot command in order to instruct hardware to catch current and
maximal occupancy values, and clear command in order to clear the
historical maximal values.

Also port-pool and tc-pool-bind command response messages are extended to
carry occupancy values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>