When iterating over a chain in reverse (oldest block first), this
patch correctly marks the PUtable[] entry of the second to last erase
block of a chain as BLOCK_NIL, regardless of whether or not it can
format the last block successfully. Before, the second to last block
was only marked as pointing to BLOCK_NIL if INFTL_formatblock()
succeeded on the last block of the chain, which could potentially
result in an infinite loop if the block was worn out and refused to
format.
Signed-off-by: Daniel Rosenthal <danielrosenthal@acm.org>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

...since it only probes that
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Now that the needed helpers are exported, it becomes a nice simple 
switch over. Closes #9420
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

.... so that they can be used by MTD map drivers. Lets us close #9420
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

The patch fixes CFI issue with multipartitional devices leading to the 
set of errors or even deadlock. The problem is CFI FL_SYNCING state race 
with flash operations (e.g. erase suspend). It is reproduced by running 
intensive writes on one JFFS2 partition and simultaneously performing 
mount/unmount cycle on another partition of the same chip.
Signed-off-by: Alexander Belyakov <abelyako@googlemail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Some chips require a RESET after power-up (e.g. Micron MT29FxGxxxxx).
The first command sent is NAND_CMD_READID.
Issue a NAND_CMD_RESET in nand_scan_ident before reading the device id.
Tested with an MT29F4G08AAC.
Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Very occasionally, (about one in a million) read operations are
ongoing after the timeout has expired.  So, retry three times
while the ongoing bit remains set.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch adds support for the integrated NAND flash controller of the
i.MX2 and i.MX3 family. It is tested on MX27 but should work on MX3
aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Minor patch to help debugging of NAND detection.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch moves some attributes out from the platform data into the
dynamically created nand device.   This results into a cleaner interface
and allows to use constant pxa3xx_nand_flash definitions.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch marks some attributes as 'const' which are set only once and
never be modified by the driver.  There are some changes in parameter
list and variable declarations too which mark them as 'const'.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch adds a MTD_NAND_PXA3xx_BUILTIN configuration variables which
allows to disable usage of builtin flash-type table.  Not enabling this
option saves some space in the generated driver.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch adds 'flash' and 'num_flash' attributes to the platform data.
There was added code in the driver to iterate across these attributes in the
detect-flash routine.  This is done similarly to the existing method
which uses a 'builtin_flash_types' field.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

This patch moves the exported datastructures from the pxa3xx_nand.c driver
into the <mach/pxa3xx_nand.h> header. This is a plain movement without
any modification of the attributes.

This is the first one of a set of patches which:

 * allows to specify used NAND flash in the platform code and allows to turn
   off the old way to specify NAND characteristics in the driver.  This way did
   not worked well as these characteristics depend on the platform and can not be
   derived from NAND id alone.

   E.g.  some NAND chips share the same ID (e.g.  K9K8G08U0A and K9NBG08U5A) but
   have different timings (which are written in the common driver currently and
   must be modified there).

 * adds 'const' annotations at various places

Further patches will be sent to the mtd-list.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

It requires cfi_qry_mode_on(), which is in cfi_util.c

Reported by Russell King
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Semun Lee <semun.lee@samsung.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.

Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().

Change some task->e?[ug]id to task_e?[ug]id().  In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Not used anywhere yet, but this complements the existing plain
'insert_resource()' functionality with a version that can expand the
resource we are adding in order to fix up any conflicts it has with
existing resources.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: oxygen: fix distorted output on AK4396-based cards
  Revert "ALSA: hda - Added model selection for iMac 24""

Pulling the ethernet cable on a 2.6.27-rc system with NFS mounts
currently leads to an ongoing flood of soft lockup detector backtraces
for all tasks blocked on the NFS mounts when the hickup takes
longer than 120s.

I don't think NFS problems should be all that noisy.

Luckily there's a reasonably easy way to distingush this case.

Don't report task softlockup warnings for tasks in TASK_KILLABLE
state, which is used by the network file systems.

I believe this patch is a 2.6.27 candidate.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit a2bd7274.

It wasn't really right to begin with (there's a better fix for the
problem with e820 reservations clashing with PCI BAR's pending), but it
also actually causes more regressions, so it should be reverted even
before the better fix is finalized.

Rafael reports that this commit broke AHCI detection, and thus causes
the kernel to not boot on his quad core test box.
Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: David Witbrodt <dawitbro@sbcglobal.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When changing the sample rate, the CMI8788's master clock output becomes
unstable for a short time.  The AK4396 needs the master clock to do SPI
writes, so writing to an AK4396 control register directly after a sample
rate change will garble the value.  In our case, this leads to the DACs
being misconfigured to I2S sample format, which results in a wrong
output level and horrible distortions on samples louder than -6 dB.

To fix this, we need to wait until the new master clock signal has
become stable before doing SPI writes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5226/1: remove unmatched comment end.
  [ARM] Skip memory holes in FLATMEM when reading /proc/pagetypeinfo
  [ARM] use bcd2bin/bin2bcd
  [ARM] use the new byteorder headers
  [ARM] OMAP: Fix 2430 SMC91x ethernet IRQ
  [ARM] OMAP: Add and update OMAP default configuration files
  [ARM] OMAP: Change mailing list for OMAP in MAINTAINERS
  [ARM] S3C2443: Fix the S3C2443 clock register definitions
  [ARM] JIVE: Fix the spi bus numbering
  [ARM] S3C24XX: pwm.c: stop debugging output
  [ARM] S3C24XX: Fix sparse warnings in pwm.c
  [ARM] S3C24XX: Fix spare errors in pwm-clock driver
  [ARM] S3C24XX: Fix sparse warnings in arch/arm/plat-s3c24xx/gpiolib.c
  [ARM] S3C24XX: Fix nor-simtec driver sparse errors
  [ARM] 5225/1: zaurus: Register I2C controller for audio codecs
  [ARM] orion5x: update defconfig to v2.6.27-rc4
  [ARM] Orion: register UART1 on QNAP TS-209 and TS-409
  [ARM] Orion: activate lm75 driver on DNS-323
  [ARM] Orion: fix MAC detection on QNAP TS-209 and TS-409
  [ARM] Orion: Fix boot crash on Kurobox Pro

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
  Blackfin arch: Fix PM building on BF52x: No ROTWE on BF52x, add USBWE
  Blackfin arch: sram: use 'unsigned long' for irqflags
  Blackfin arch: let PCI depend on BROKEN
  Blackfin arch: move include/asm-blackfin header files to arch/blackfin
  Blackfin arch: fix bug - MPU crashes under stress
  Blackfin arch: Fix bug - when to rmmod the L1_module, it stucks and then reboot the board.
  Blackfin arch: dont actually need to muck with EMAC_SYSTAT for BF52x for demuxing
  Blackfin arch: Add MTD Partitions for MTD_DATAFLASH, increase max SPI SCLK

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  exit signals: use of uninitialized field notify_count
  lockdep: fix invalid list_del_rcu in zap_class
  lockstat: repair erronous contention statistics
  lockstat: fix numerical output rounding error

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: rt-bandwidth accounting fix
  sched: fix sched_rt_rq_enqueue() resched idle

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: update defconfigs
  x86: msr: fix bogus return values from rdmsr_safe/wrmsr_safe
  x86: cpuid: correct return value on partial operations
  x86: msr: correct return value on partial operations
  x86: cpuid: propagate error from smp_call_function_single()
  x86: msr: propagate errors from smp_call_function_single()
  smp: have smp_call_function_single() detect invalid CPUs

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c: Prevent log spam on some DVB adapters
  i2c: Add missing kerneldoc descriptions
  i2c: Fix device_init_wakeup place

In accordance with commit f42ac38c
("ftrace: disable tracing for suspend to ram"), disable tracing
around the suspend code in hibernation code paths.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

remove unmatched comment end.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

It fixes an accounting bug where we would continue accumulating runtime
even though the bandwidth control is disabled. This would lead to very long
throttle periods once bandwidth control gets turned on again.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>

Using just 'unsigned' will make flags an unsigned int. While this is
arguably not an error on blackfin where sizeof(int) == sizeof(long),
the patch is still justified on the grounds of principle.

The patch was generated using the Coccinelle semantic patch framework.

Cc: Julia Lawall <julia@diku.dk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>

When sysctl_sched_rt_runtime is set to something other than -1 and the
CONFIG_RT_GROUP_SCHED kernel parameter is NOT enabled, we get into a state
where we see one or more CPUs idling forvever even though there are
real-time
tasks in their rt runqueue that are able to run (no longer throttled).

The sequence is:

- A real-time task is running when the timer sets the rt runqueue
    to throttled, and the rt task is resched_task()ed and switched
    out, and idle is switched in since there are no non-rt tasks to
    run on that cpu.

- Eventually the do_sched_rt_period_timer() runs and un-throttles
    the rt runqueue, but we just exit the timer interrupt and go back
    to executing the idle task in the idle loop forever.

If we change the sched_rt_rq_enqueue() routine to use some of the code
from the CONFIG_RT_GROUP_SCHED enabled version of this same routine and
resched_task() the currently executing task (idle in our case) if it is
a lower priority task than the higher rt task in the now un-throttled
runqueue, the problem is no longer observed.
Signed-off-by: John Blackwood <john.blackwood@ccur.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Some DVB adapters do not support the special I2C transaction that we
use for probing purposes. There's no point in logging this event, as
there's nothing the user can do and in general there is no actual
problem. So, degrade one of these messages to a debug message, and
move the other one around so that it is only printed on bogus drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>

Add missing kernel descriptions of struct i2c_driver members.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: David Brownell <david-b@pacbell.net>

device_init_wakeup must be called after device_register.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>