Move operator of complex expression to the end of the lines to preserve
consistency.
Signed-off-by: Leonid V. Fedorenchik <leonidsbox@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Change wrong indent (with spaces and less than 7 columns) of statements
to tabs.
Signed-off-by: Leonid V. Fedorenchik <leonidsbox@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Change obscure line endings to less obscure ones. (improve readability)
Signed-off-by: Leonid V. Fedorenchik <leonidsbox@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Delete unnecessary space before indented statement.
Signed-off-by: Leonid V. Fedorenchik <leonidsbox@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Add curly braces around else clause because corresponding if has them.
Signed-off-by: Leonid V. Fedorenchik <leonidsbox@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Line up comments to the same column.
Signed-off-by: Leonid V. Fedorenchik <leonidsbox@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

i2c_master_send returns negative errno, or else the number of bytes written.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

lirc_serial_probe() must fail if request_irq() returns an error, even if
it isn't EBUSY or EINVAL,
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Device not found?  ENODEV, not EINVAL.
Write to read-only device?  EPERM, not EBADF.
Invalid argument?  EINVAL, not ENOSYS.
Unsupported ioctl?  ENOIOCTLCMD, not ENOSYS.
Another function returned an error code?  Use that, don't replace it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

A resume function cannot remove the device it is resuming!
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Failure to allocate the I/O region leaves the IRQ allocated.
A later failure leaves them both allocated.
Reported-by: Torsten Crass <torsten.crass@eBiology.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Currently the module init function registers a platform_device and
only then allocates its IRQ and I/O region.  This allows allocation to
race with the device's suspend() function.  Instead, allocate
resources in the platform driver's probe() function and free them in
the remove() function.

The module exit function removes the platform device before the
character device that provides access to it.  Change it to reverse the
order of initialisation.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The function setup_vpif_input_channel_mode() used the VSCLKDIS register
instead of VIDCLKCTL. This meant that when in HD mode videoport channel 0
used a different clock from channel 1.

Clearly a copy-and-paste error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

I have been working many years without problems.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

I have been working many years without problems.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

It is param that could be potentially unsupported and
due to that it is good idea to check it very first.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

All tuners used with cxd2820r offers IF frequency so switch that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Chip configures IF frequency resolution of 50 kHz. Round it nearest.
Off-by 50 kHz is almost nothing in real life...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Get IF frequency from tuner if tuner provides it.

Remove TDA18271 and TDA18218 IF frequency hacks since both tuners provides .get_if_frequency().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Commit ede676c7 ("[...] add digital support for PV SBTVD hybrid")
added "select MEDIA_TUNER_NXP18271" to the VIDEO_CX231XX_DVB Kconfig
entry. But there's no Kconfig symbol MEDIA_TUNER_NXP18271. That should
have been MEDIA_TUNER_TDA18271. (The code added in that commit uses
tda18271_attach, which is only available if MEDIA_TUNER_TDA18271 is
set.)

The selects of MEDIA_TUNER_XC5000 and MEDIA_TUNER_TDA18271 should only
be done if MEDIA_TUNER_CUSTOMISE isn't set.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Add the maintainers for the m5mols driver
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This patch supports card Mygica X8507 (analog part)

This controller is a copy of driver card Mygica X8506

This patch depends on patch cx23885-alsa

To do: FM, ISDB-t, remote control, audio for composite1, S-Video and
video component.
Signed-off-by: Alfredo J. Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

There's one comment that has been copied from bttv to many other
media/video drivers:

/* init + register i2c algo-bit adapter */

Meanwhile, many drivers use hardware I2C implementations instead of
relying on i2c-algo-bit, so this comment is misleading. Remove the
reference to "algo-bit" from all drivers, to avoid any confusion. This
is the best way to ensure that the comments won't go out of sync
again. Anyone interested in the implementation details would rather
look at the code itself.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/dvb/firewire/firedtv-avc.c: In function ‘avc_tuner_tuneqpsk’:
drivers/media/dvb/firewire/firedtv-avc.c:394:4: warning: enumeration value ‘ROLLOFF_15’ not handled in switch [-Wswitch]
drivers/media/dvb/firewire/firedtv-avc.c:394:4: warning: enumeration value ‘ROLLOFF_13’ not handled in switch [-Wswitch]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/video/em28xx/em28xx-cards.c:339:30: warning: ‘hauppauge_930c_gpio’ defined but not used [-Wunused-variable]
drivers/media/video/em28xx/em28xx-dvb.c: In function ‘em28xx_dvb_init’:
drivers/media/video/em28xx/em28xx-dvb.c:886:3: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Add missing dev argument in dev_err() call to correct an error
introduced in commit 88010289Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Fixed submit urb logic so hardware doesn't hang trying to transmit
signal data

Removed unneeded enable/disable detector commands in
redrat3_transmit_ir (the hardware does this anyway) and converted
arguments to unsigned as per 5588dc2bSigned-off-by: Andrew Vincer <andrew@redrat.co.uk>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Smatch complains that the wrong limiter is used here:
drivers/media/dvb/ttpci/av7110.c +906 dvb_feed_start_pid(12)
	error: buffer overflow 'npids' 5 <= 19

Here is the problem code:
   905          i = dvbdmxfeed->pes_type;
   906          npids[i] = (pid[i]&0x8000) ? 0 : pid[i];

"npids" is a 5 element array declared on the stack.  If
dvbdmxfeed->pes_type is more than 4 we probably put a (u16)0 past
the end of the array.

If dvbdmxfeed->pes_type is over 4 the rest of the function doesn't
do anything.  dvbdmxfeed->pes_type is capped at less than
DMX_TS_PES_OTHER (20) in the caller function, but I changed it to
less than or equal to DMX_TS_PES_PCR (4).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This patch fix a bug in the i2c code of ttusb2 driver.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

I get this error when compiling for_v3.3:

There is a include <linux/module.h> missing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

priv gets dereferenced in mt9t112_set_params() so we should return
before calling that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This patch to the IR RC6 decoder adds support for variable length
mode-6A frames which can range in size from 8 to 128 bits.  Please refer
to the following link for a detailed explanation or RC6 frames:
http://slydiman.narod.ru/scr/kb/rc6.htm

This change removes the assumption that frames are fixed length
(currently either 24 or 32 data bits) and actually counts the number of
bits until an end of frame marker is seen.

[mchehab@redhat.com: Tested with a RC-6(0) IR - 16 bits]
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

* tag 'v3.2-rc2': (3068 commits)
  Linux 3.2-rc2
  hfs: add sanity check for file name length
  fsl-rio: fix compile error
  blackfin: Fixup export.h includes
  Blackfin: add serial TX IRQ in individual platform resource
  virtio-pci: fix use after free
  ACPI / cpuidle: Remove acpi_idle_suspend (to fix suspend regression)
  drm/radeon/kms/combios: fix dynamic allocation of PM clock modes
  [CPUFREQ] db8500: fix build error due to undeclared i variable
  bma023: Add SFI translation for this device
  vrtc: change its year offset from 1960 to 1972
  ce4100: fix a build error
  arm/imx: fix imx6q mmc error when mounting rootfs
  arm/imx: fix AUTO_ZRELADDR selection
  arm/imx: fix the references to ARCH_MX3
  ARM: mx51/53: set pwm clock parent to ipg_perclk
  btrfs: rename the option to nospace_cache
  drm/radeon/kms/pm: switch to dynamically allocating clock mode array
  drm/radeon/kms: optimize r600_pm_profile_init
  drm/radeon/kms/pm: add a proper pm profile init function for fusion
  ...

Conflicts:
	drivers/media/radio/Kconfig

This protocol is found on Sanyo/Aiwa remotes.

Tested with an Aiwa RC-7AS06 remote control.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>