- 27 May, 2014 40 commits
-
-
Marek Szyprowski authored
USB3503 chip supports 8 values of reference clock. The value is specified by REF_SEL[1:0] pins and INT_N line. This patch add support for getting 'refclk' clock, enabling it and setting INT_N line according to the value of the gathered clock. If no clock has been specified, driver defaults to the old behaviour (assuming that clock has been specified by REF_SEL pins from primary reference clock frequencies table). Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Todd E Brandt authored
This patch creates a separate instance of the usb_address0 mutex for each USB bus, and attaches it to the usb_bus device struct. This allows devices on separate buses to be enumerated in parallel; saving time. In the current code, there is a single, global instance of the usb_address0 mutex which is used for all devices on all buses. This isn't completely necessary, as this mutex is only needed to prevent address0 collisions for devices on the *same* bus (usb 2.0 spec, sec 4.6.1). This superfluous coverage can cause additional delay in system resume on systems with multiple hosts (up to several seconds depending on what devices are attached). Signed-off-by:
Todd Brandt <todd.e.brandt@linux.intel.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Denis Turischev authored
Patch "xhci: Switch Intel Lynx Point ports to EHCI on shutdown." commit c09ec25d is not fully correct It switches both Lynx Point and Lynx Point-LP ports to EHCI on shutdown. On some Lynx Point machines it causes spurious interrupt, which wake the system: bugzilla.kernel.org/show_bug.cgi?id=76291 On Lynx Point-LP on the contrary switching ports to EHCI seems to be necessary to fix these spurious interrupts. Signed-off-by:
Denis Turischev <denis@compulab.co.il> Reported-by:
Wulf Richartz <wulf.richartz@gmail.com> Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Naoki MATSUMOTO authored
It no longer occurs in Kconfig. USB: remove CONFIG_USB_DEVICEFS(fb28d58b) leaked remove defconfig. Signed-off-by:
Naoki MATSUMOTO <nekomatu+linux@gmail.com> Signed-off-by:
-
Oliver Neukum authored
Parsing device descriptors can fail due to a failed memory allocation. The error needs to be properly propagated to the upper layers. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Oliver Neukum authored
There's a window during which read() would return 0 instead of a correct error for no data yet. Reorder initialization to fix the race. Signed-off-by:
-
Oliver Neukum authored
The workqueue handler may call appledisplay_bl_get_brightness() while user space calls appledisplay_bl_update_status(). As they share a buffer that must not happen. Use a mutex for mutual exclusion. Signed-off-by:
-
Oliver Neukum authored
send_request_dev_dep_msg_in() use a buffer allocated on the stack. Fix by kmalloc()ing the buffer. Signed-off-by:
-
Oliver Neukum authored
Converting the header to BIT for readability. No functional change. Signed-off-by:
-
Ricardo Ribalda Delgado authored
This patch adds support for the PLX USB3380 and USB3382. This driver is based on the driver from the manufacturer. Since USB338X is register compatible with NET2280, I thought that it would be better to include this hardware into net2280 driver. Manufacturer's driver only supported the USB33X, did not follow the Kernel Style and contain some trivial errors. This patch has tried to address this issues. This patch has only been tested on USB338x hardware, but the merge has been done trying to not affect the behaviour of NET2280. Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Tested-by:
-
Julia Lawall authored
Delete unnecessary local variable whose value is always 0 and that hides the fact that the result is always 0. A simplified version of the semantic patch that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r exists@ local idexpression ret; expression e; position p; @@ -ret = 0; ... when != ret = e return - ret + 0 ; // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Liviu Dudau authored
Signed-off-by:
Liviu Dudau <Liviu.Dudau@arm.com> Signed-off-by:
Ryan Harkin <ryan.harkin@linaro.org> Signed-off-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
-
Oliver Neukum authored
Either we log for all chips we set the quirk for or for none. This patch reports it for all chips. Signed-off-by:
Oliver Neukum <oliver@neukum.org> Signed-off-by:
-
Boris BREZILLON authored
On the Allwinner's A31 SoC the reset line connected to the EHCI IP has to be deasserted for the EHCI block to be usable. Add support for an optional reset controller that will be deasserted on power off and asserted on power on. Signed-off-by:
Boris BREZILLON <boris.brezillon@free-electrons.com> Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
-
Maxime Ripard authored
The OHCI controllers used in the Allwinner A31 are asserted in reset using a global reset controller. Add optional support for such a controller in the OHCI platform driver. Signed-off-by:
-
Arnd Bergmann authored
The dependency on the isp1301 driver is not something that should be in the main OHCI driver but rather the SoC specific part of it. This moves the dependency for LPC32xx into USB_OHCI_HCD_LPC32XX, and changes the 'select ISP1301_OMAP' to a similar 'depends on'. Since the same dependency exists for the client driver, do the same change there. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Cc: linux-omap@vger.kernel.org Acked-by:
-
Arnd Bergmann authored
The PHY setup code of the TI DaVinci DA8xx OHCI controller uses ad-hoc register access using a pointer that is meant to be used only by the DaVinci platform implementation and that is intentionally not exported to loadable modules. This results in a link error on configurations that use a modular OHCI code on this platform. While the proper solution for this problem would be to implement a real PHY driver shared by ohci-da8xx and musb-da8xx, this patch for now just works around the build error by only allowing the ohci-da8xx code to be built-in. Signed-off-by:
-
Arnd Bergmann authored
If we build a kernel with PM_SUSPEND set and no PM_SLEEP, we get a build warning in the xhci-plat driver about unused functions. To fix this, use "#ifdef CONFIG_PM_SLEEP", like we do in most other drivers nowadays. Signed-off-by:
-
Dinh Nguyen authored
The dwc2 IP on the SOCFPGA cannot use the default HW configured FIFO sizes. The total FIFO depth as read from GHWCFG3 reports 0x1f80 or 8064 32-bit words. But the GRXFSIZ, GNPTXFSIZ, and HPTXFSIZ register defaults to 0x2000 or 8192 32-bit words. So the driver cannot just use the fifo sizes as read from those registers. For platforms that face the same issue, this commits sets the RX, periodic TX, and non-periodic TX fifo size to those that are recommended v2.93a spec for the DWC2 IP. Implements Method #2 from the Synopsys v2.93a spec for the DWC2. Signed-off-by:
Dinh Nguyen <dinguyen@altera.com> Acked-by:
Paul Zimmerman <paulz@synopsys.com> Reviewed-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Dinh Nguyen authored
Even though the IP supports Descriptor DMA mode, it does not support SPLIT transactions in this mode. So the driver, in its currently form, will not support LS/FS devices when connected to a HS Hub if Descriptor DMA mode is enabled. So we should just default to disable descriptor dma mode. Signed-off-by:
-
Gregory CLEMENT authored
This commit extends the compatible string list of the xhci-platform binding with the new "armada-375-xhci" and "armada-380-xhci" compatible strings. It is used to describe the XHCI controller which is available in the Armada 375 and 38x SoCs. It also indicates that an optional 'clocks' property is now supported. Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Gregory CLEMENT authored
The Armada 375 and 38x SoCs come with an XHCI controller that requires some specific initialization related to the MBus windows configuration. This patch adds the support for this special configuration as an XHCI quirk executed during probe. Two new compatible strings are added to identify the Armada 375 and Armada 38x XHCI controllers, and therefore enable the relevant quirk. Signed-off-by:
-
Gregory CLEMENT authored
Some platforms (such as the Armada 38x ones) can gate the clock of their USB controller. This patch adds the support for one clock in xhci-plat, by enabling it during probe and disabling it on remove. To achieve this, it adds a 'struct clk *' member in xhci_hcd. While only used for now in xhci-plat, it might be used by other drivers in the future. Moreover, the xhci_hcd structure already holds other members such as msix_count and msix_entries, which are MSI-X specific, and therefore only used by xhci-pci. Signed-off-by:
-
Gregory CLEMENT authored
Sorting the headers in alphabetic order will help to reduce the conflict when adding new headers later. Signed-off-by:
-
Thomas Petazzoni authored
This commit updates the Device Tree binding documentation of ehci-orion to take into account the fact that we can now optionally pass a clock and a PHY reference. Signed-off-by:
-
Gregory CLEMENT authored
This commit extends the ehci-orion so that it can optionally be passed a reference to a PHY through the Device Tree. It will be useful for the Armada 375 SoCs. If no PHY is provided then the behavior of the driver is unchanged. [Thomas: use devm_phy_optional_get() so that we handle -EPROBE_DEFER properly. Also call phy_power_off() when needed, and rename goto labels.] Signed-off-by:
-
Gregory CLEMENT authored
In order to disable the clock in the ->remove() function, a call to devm_clk_get() is being made, which further increases the reference count of the clock. In order to clean this up, a private structure holding a pointer to the clock is added using the override mechanism provided by the ehci framework. This makes the driver clock handling much more logical. The bug was introduced in v3.6, however the ehci framework allowing to use the override mechanism has only been introduced in v3.8, so this patch won't apply before it. [Thomas: reword commit log, fix goto label names.] Fixes: 8c869eda ('ARM: Orion: EHCI: Add support for enabling clocks') Cc: <stable@vger.kernel.org> # v3.8+ Signed-off-by:
-
Thomas Petazzoni authored
In preparation to the introduction of additional initialization steps in ehci_orion_drv_probe(), we rename the error goto labels from err1, err2 and err3 names to some more meaningful names. Signed-off-by:
-
Thomas Petazzoni authored
Commit 77dae54a ('ARM: Kirkwood: ehci-orion: Add device tree binding') added the Device Tree binding for the ehci-orion driver. To achieve that with the irq, it used the irq_of_parse_and_map() function when probed in DT-mode, and platform_get_irq() when probed in non-DT mode. This is not necessary: platform_get_irq() works just as fine in DT-mode, since the conversion from DT information to 'struct resource' is done by the generic layers of the kernel. Therefore, this commit switches back to use just platform_get_irq(). Signed-off-by:
-
Peter Chen authored
Since usb otg fsm implementation is not related to usb phy. We move it from usb/phy/ to usb/common/, and rename it to reflect its real meaning. Cc: Felipe Balbi <balbi@ti.com> Signed-off-by:
Peter Chen <peter.chen@freescale.com> Signed-off-by:
-
Peter Chen authored
Since we will have more usb-common things, and it will let usb-common.c be larger and larger, we create a folder named usb/common for all usb common things. Cc: Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Fabio Estevam authored
%pad notation automatically prints in hexadecimal format (with '0x'), so remove the unneeded '0x' to avoid a '0x0x' string. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Acked-by:
-
David Mosberger authored
Signed-off-by:
David Mosberger <davidm@egauge.net> Signed-off-by:
-
Thomas Pugliese authored
Fix variable set but not used warnings in UWB. Signed-off-by:
Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by:
-
Thomas Pugliese authored
Comment typo fix. Signed-off-by:
-
Thomas Pugliese authored
Fix whitespace and line length issues reported by checkpatch. Signed-off-by:
-
Peter Chen authored
Since we have already removed the usage of CONFIG_USB_DEBUG, it is meaningless that there is still a configuration entry for CONFIG_USB_DEBUG. Signed-off-by:
-
Yijing Wang authored
Pci_enable_device() will set device power state to D0, so it's no need to do it again after call pci_enable_device(). Signed-off-by:
Yijing Wang <wangyijing@huawei.com> Acked-by:
-
Rickard Strandqvist authored
Move control-urb dereference to after NULL-check. There is otherwise a risk of a possible null pointer dereference. Was largely found by using a static code analysis program called cppcheck. [Johan: modify commit message somewhat ] [gkh: remove stable tag as it's not a real problem that anyone has ever hit] Signed-off-by:
Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Johan Hovold authored
Fix incorrect pipe directions in control requests (which has been silently fixed up by USB core). Signed-off-by:
-
