- 11 Mar, 2020 40 commits
-
-
Jack Pham authored
[ Upstream commit a2035411 ] USB 3.x SuperSpeed peripherals can draw up to 900mA of VBUS power when in configured state. However, if a configuration wanting to take advantage of this is added with MaxPower greater than 500 (currently possible if using a ConfigFS gadget) the composite driver fails to accommodate this for a couple reasons: - usb_gadget_vbus_draw() when called from set_config() and composite_resume() will be passed the MaxPower value without regard for the current connection speed, resulting in a violation for USB 2.0 since the max is 500mA. - the bMaxPower of the configuration descriptor would be incorrectly encoded, again if the connection speed is only at USB 2.0 or below, likely wrapping around U8_MAX since the 2mA multiplier corresponds to a maximum of 510mA. Fix these by adding checks against the current gadget->speed when the c->MaxPower value is used (set_config() and composite_resume()) and appropriately limit based on whether it is currently at a low-/full-/high- or super-speed connection. Because 900 is not divisible by 8, with the round-up division currently used in encode_bMaxPower() a MaxPower of 900mA will result in an encoded value of 0x71. When a host stack (including Linux and Windows) enumerates this on a single port root hub, it reads this value back and decodes (multiplies by 8) to get 904mA which is strictly greater than 900mA that is typically budgeted for that port, causing it to reject the configuration. Instead, we should be using the round-down behavior of normal integral division so that 900 / 8 -> 0x70 or 896mA to stay within range. And we might as well change it for the high/full/low case as well for consistency. N.B. USB 3.2 Gen N x 2 allows for up to 1500mA but there doesn't seem to be any any peripheral controller supported by Linux that does two lane operation, so for now keeping the clamp at 900 should be fine. Signed-off-by:
Jack Pham <jackp@codeaurora.org> Signed-off-by:
Felipe Balbi <balbi@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Daniel Golle authored
[ Upstream commit 87c5cbf7 ] On AR934x this UART is usually not initialized by the bootloader as it is only used as a secondary serial port while the primary UART is a newly introduced NS16550-compatible. In order to make use of the ar933x-uart on AR934x without RTS/CTS hardware flow control, one needs to set the UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this UART is used as primary/console, the bootloader on AR934x typically doesn't set those bits. Setting them explicitely on AR933x should not do any harm, so just set them unconditionally. Tested-by:
Chuanhong Guo <gch981213@gmail.com> Signed-off-by:
Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.orgSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Eugenio Pérez authored
[ Upstream commit 42d84c84 ] Doing so, we save one call to get data we already have in the struct. Also, since there is no guarantee that getname use sockaddr_ll parameter beyond its size, we add a little bit of security here. It should do not do beyond MAX_ADDR_LEN, but syzbot found that ax25_getname writes more (72 bytes, the size of full_sockaddr_ax25, versus 20 + 32 bytes of sockaddr_ll + MAX_ADDR_LEN in syzbot repro). Fixes: 3a4d5c94 ("vhost_net: a kernel-level virtio server") Reported-by: syzbot+f2a62d07a5198c819c7b@syzkaller.appspotmail.com Signed-off-by:
Eugenio Pérez <eperezma@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Paul Moore authored
[ Upstream commit 75612528 ] This patch ensures that we always check the netlink payload length in audit_receive_msg() before we take any action on the payload itself. Cc: stable@vger.kernel.org Reported-by: syzbot+399c44bf1f43b8747403@syzkaller.appspotmail.com Reported-by: syzbot+e4b12d8d202701f08b6d@syzkaller.appspotmail.com Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Wei Yang authored
commit cb829624 upstream. The page could be a tail page, if this is the case, this BUG_ON will never be triggered. Link: http://lkml.kernel.org/r/20200110032610.26499-1-richardw.yang@linux.intel.com Fixes: e9b61f19 ("thp: reintroduce split_huge_page()") Signed-off-by:
Wei Yang <richardw.yang@linux.intel.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
commit 3f777403 upstream. We need to set actions->ms.map since 599a2f38 ("perf hists browser: Check sort keys before hot key actions"), as in that patch we bail out if map is NULL. Reviewed-by:
Jiri Olsa <jolsa@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: 599a2f38 ("perf hists browser: Check sort keys before hot key actions") Link: https://lkml.kernel.org/n/tip-wp1ssoewy6zihwwexqpohv0j@git.kernel.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Christophe JAILLET authored
commit 5a44c71c upstream. 'alloc_etherdev_mqs()' expects first 'tx', then 'rx'. The semantic here looks reversed. Reorder the arguments passed to 'alloc_etherdev_mqs()' in order to keep the correct semantic. In fact, this is a no-op because both XGENE_NUM_[RT]X_RING are 8. Fixes: 107dec27 ("drivers: net: xgene: Add support for multiple queues") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Jason Wang authored
commit 2f3ab622 upstream. When link is down, writes to the device might fail with -EIO. Userspace needs an indication when the status is resolved. As a fix, tun_net_open() attempts to wake up writers - but that is only effective if SOCKWQ_ASYNC_NOSPACE has been set in the past. This is not the case of vhost_net which only poll for EPOLLOUT after it meets errors during sendmsg(). This patch fixes this by making sure SOCKWQ_ASYNC_NOSPACE is set when socket is not writable or device is down to guarantee EPOLLOUT will be raised in either tun_chr_poll() or tun_sock_write_space() after device is up. Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Eric Dumazet <edumazet@google.com> Fixes: 1bd4978a ("tun: honor IFF_UP in tun_get_user()") Signed-off-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
Tommi Rantala <tommi.t.rantala@nokia.com>
-
yangerkun authored
After include 3b5a3997 ("slip: Fix memory leak in slip_open error path") and e58c1912 ("slip: Fix use-after-free Read in slip_open") with 4.4.y/4.9.y. We will trigger a bug since we can double free sl->dev in slip_open. Actually, we should backport cf124db5 ("net: Fix inconsistent teardown and release of private netdev state.") too since it has delete free_netdev from sl_free_netdev. Fix it by delete free_netdev from slip_open. Signed-off-by:
yangerkun <yangerkun@huawei.com> Signed-off-by:
-
Sean Christopherson authored
commit fcfbc617 upstream. When reading/writing using the guest/host cache, check for a bad hva before checking for a NULL memslot, which triggers the slow path for handing cross-page accesses. Because the memslot is nullified on error by __kvm_gfn_to_hva_cache_init(), if the bad hva is encountered after crossing into a new page, then the kvm_{read,write}_guest() slow path could potentially write/access the first chunk prior to detecting the bad hva. Arguably, performing a partial access is semantically correct from an architectural perspective, but that behavior is certainly not intended. In the original implementation, memslot was not explicitly nullified and therefore the partial access behavior varied based on whether the memslot itself was null, or if the hva was simply bad. The current behavior was introduced as a seemingly unintentional side effect in commit f1b9dd5e ("kvm: Disallow wraparound in kvm_gfn_to_hva_cache_init"), which justified the change with "since some callers don't check the return code from this function, it sit seems prudent to clear ghc->memslot in the event of an error". Regardless of intent, the partial access is dependent on _not_ checking the result of the cache initialization, which is arguably a bug in its own right, at best simply weird. Fixes: 8f964525 ("KVM: Allow cross page reads and writes from cached translations.") Cc: Jim Mattson <jmattson@google.com> Cc: Andrew Honig <ahonig@google.com> Signed-off-by:
Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Aleksa Sarai authored
commit 2b98149c upstream. It's over-zealous to return hard errors under RCU-walk here, given that a REF-walk will be triggered for all other cases handling ".." under RCU. The original purpose of this check was to ensure that if a rename occurs such that a directory is moved outside of the bind-mount which the resolution started in, it would be detected and blocked to avoid being able to mess with paths outside of the bind-mount. However, triggering a new REF-walk is just as effective a solution. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Fixes: 397d425d ("vfs: Test for and handle paths that are unreachable from their mnt_root") Suggested-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Aleksa Sarai <cyphar@cyphar.com> Signed-off-by:
-
Arthur Kiyanovski authored
commit 470793a7 upstream. As the name suggests ETH_RSS_HASH_NO_CHANGE is received upon changing the key or indirection table using ethtool while keeping the same hash function. Also add a function for retrieving the current hash function from the ena-com layer. Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by:
Sameeh Jubran <sameehj@amazon.com> Signed-off-by:
Saeed Bshara <saeedb@amazon.com> Signed-off-by:
Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by:
-
Nikolay Aleksandrov authored
commit 3a20773b upstream. Since nl_groups is a u32 we can't bind more groups via ->bind (netlink_bind) call, but netlink has supported more groups via setsockopt() for a long time and thus nlk->ngroups could be over 32. Recently I added support for per-vlan notifications and increased the groups to 33 for NETLINK_ROUTE which exposed an old bug in the netlink_bind() code causing out-of-bounds access on archs where unsigned long is 32 bits via test_bit() on a local variable. Fix this by capping the maximum groups in netlink_bind() to BITS_PER_TYPE(u32), effectively capping them at 32 which is the minimum of allocated groups and the maximum groups which can be bound via netlink_bind(). CC: Christophe Leroy <christophe.leroy@c-s.fr> CC: Richard Guy Briggs <rgb@redhat.com> Fixes: 4f520900 ("netlink: have netlink per-protocol bind function return an error code.") Reported-by:
Erhard F. <erhard_f@mailbox.org> Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Chris Wilson authored
commit 9144d75e upstream. net_dim.h has a rather useful extension to BITS_PER_BYTE to compute the number of bits in a type (BITS_PER_BYTE * sizeof(T)), so promote the macro to bitops.h, alongside BITS_PER_BYTE, for wider usage. Link: http://lkml.kernel.org/r/20180706094458.14116-1-chris@chris-wilson.co.ukSigned-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
Jani Nikula <jani.nikula@intel.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Andy Gospodarek <gospo@broadcom.com> Cc: David S. Miller <davem@davemloft.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Andy Shevchenko authored
commit 7febbcbc upstream. The commit 54e53b2e ("tty: serial: 8250: pass IRQ shared flag to UART ports") nicely explained the problem: ---8<---8<--- On some systems IRQ lines between multiple UARTs might be shared. If so, the irqflags have to be configured accordingly. The reason is: The 8250 port startup code performs IRQ tests *before* the IRQ handler for that particular port is registered. This is performed in serial8250_do_startup(). This function checks whether IRQF_SHARED is configured and only then disables the IRQ line while testing. This test is performed upon each open() of the UART device. Imagine two UARTs share the same IRQ line: On is already opened and the IRQ is active. When the second UART is opened, the IRQ line has to be disabled while performing IRQ tests. Otherwise an IRQ might handler might be invoked, but the IRQ itself cannot be handled, because the corresponding handler isn't registered, yet. That's because the 8250 code uses a chain-handler and invokes the corresponding port's IRQ handling routines himself. Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't disabled while performing tests and the kernel correctly detects a spurious IRQ. So, adding this flag to the DT probe solves the issue. Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the IRQF_SHARED flag can be set unconditionally as well. Example stack trace by performing `echo 1 > /dev/ttyS2` on a non-patched system: |irq 85: nobody cared (try booting with the "irqpoll" option) | [...] |handlers: |[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt |Disabling IRQ #85 ---8<---8<--- But unfortunately didn't fix the root cause. Let's try again here by moving IRQ flag assignment from serial_link_irq_chain() to serial8250_do_startup(). This should fix the similar issue reported for 8250_pnp case. Since this change we don't need to have custom solutions in 8250_aspeed_vuart and 8250_of drivers, thus, drop them. Fixes: 1c2f0493 ("serial: 8250: add IRQ trigger support") Reported-by:
Li RongQing <lirongqing@baidu.com> Cc: Kurt Kanzenbach <kurt@linutronix.de> Cc: Vikram Pandita <vikram.pandita@ti.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable <stable@vger.kernel.org> Acked-by:
Kurt Kanzenbach <kurt@linutronix.de> Link: https://lore.kernel.org/r/20200211135559.85960-1-andriy.shevchenko@linux.intel.com [Kurt: Backport to v4.9] Signed-off-by:
-
Nathan Chancellor authored
When doing the 4.9 merge into certain Android trees, I noticed a warning from Android's deprecated GCC 4.9.4, which causes a build failure in those trees due to basically -Werror: fs/ecryptfs/keystore.c: In function 'ecryptfs_parse_packet_set': fs/ecryptfs/keystore.c:1357:2: warning: 'auth_tok_list_item' may be used uninitialized in this function [-Wmaybe-uninitialized] memset(auth_tok_list_item, 0, ^ fs/ecryptfs/keystore.c:1260:38: note: 'auth_tok_list_item' was declared here struct ecryptfs_auth_tok_list_item *auth_tok_list_item; ^ GCC 9.2.0 was not able to pick up this warning when I tested it. Turns out that Clang warns as well when -Wuninitialized is used, which is not the case in older stable trees at the moment (but shows value in potentially backporting the various warning fixes currently in upstream to get more coverage). fs/ecryptfs/keystore.c:1284:6: warning: variable 'auth_tok_list_item' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized] if (data[(*packet_size)++] != ECRYPTFS_TAG_1_PACKET_TYPE) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ fs/ecryptfs/keystore.c:1360:4: note: uninitialized use occurs here auth_tok_list_item); ^~~~~~~~~~~~~~~~~~ fs/ecryptfs/keystore.c:1284:2: note: remove the 'if' if its condition is always false if (data[(*packet_size)++] != ECRYPTFS_TAG_1_PACKET_TYPE) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ fs/ecryptfs/keystore.c:1260:56: note: initialize the variable 'auth_tok_list_item' to silence this warning struct ecryptfs_auth_tok_list_item *auth_tok_list_item; ^ = NULL 1 warning generated. Somehow, commit fe2e082f ("ecryptfs: fix a memory leak bug in parse_tag_1_packet()") upstream was not applied in the correct if block in 4.4.215, 4.9.215, and 4.14.172, which will indeed lead to use of uninitialized memory. Fix it up by undoing the bad backport in those trees then reapplying the patch in the proper location. Signed-off-by:Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
-
Wolfram Sang authored
commit 9e661ced upstream. The printout for txabrt is way too talkative and is highly annoying with scanning programs like 'i2cdetect'. Reduce it to the minimum, the rest can be gained by I2C core debugging and datasheet information. Also, make it a debug printout, it won't help the regular user. Fixes: ba92222e ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780") Reported-by:
H. Nikolaus Schaller <hns@goldelico.com> Tested-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Christophe JAILLET authored
commit bef8e2df upstream. Pointer on the memory allocated by 'alloc_progmem()' is stored in 'v->load_addr'. So this is this memory that should be freed by 'release_progmem()'. 'release_progmem()' is only a call to 'kfree()'. With the current code, there is both a double free and a memory leak. Fix it by passing the correct pointer to 'release_progmem()'. Fixes: e01402b1 ("More AP / SP bits for the 34K, the Malta bits and things. Still wants") Signed-off-by:
Paul Burton <paulburton@kernel.org> Cc: ralf@linux-mips.org Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: kernel-janitors@vger.kernel.org Signed-off-by:
-
dan.carpenter@oracle.com authored
commit 5c02c447 upstream. Syzbot reports that "hiddev" is used after it's free in hiddev_disconnect(). The hiddev_disconnect() function sets "hiddev->exist = 0;" so hiddev_release() can free it as soon as we drop the "existancelock" lock. This patch moves the mutex_unlock(&hiddev->existancelock) until after we have finished using it. Reported-by: syzbot+784ccb935f9900cc7c9e@syzkaller.appspotmail.com Fixes: 7f77897e ("HID: hiddev: fix potential use-after-free") Suggested-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Johan Korsnes authored
commit 84a40626 upstream. We have a HID touch device that reports its opens and shorts test results in HID buffers of size 8184 bytes. The maximum size of the HID buffer is currently set to 4096 bytes, causing probe of this device to fail. With this patch we increase the maximum size of the HID buffer to 8192 bytes, making device probe and acquisition of said buffers succeed. Signed-off-by:
Johan Korsnes <jkorsnes@cisco.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Armando Visconti <armando.visconti@st.com> Cc: Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Johan Korsnes authored
commit 5ebdffd2 upstream. In case a report is greater than HID_MAX_BUFFER_SIZE, it is truncated, but the report-number byte is not correctly handled. This results in a off-by-one in the following memset, causing a kernel Oops and ensuing system crash. Note: With commit 8ec321e9 ("HID: Fix slab-out-of-bounds read in hid_field_extract") I no longer hit the kernel Oops as we instead fail "controlled" at probe if there is a report too long in the HID report-descriptor. hid_report_raw_event() is an exported symbol, so presumabely we cannot always rely on this being the case. Fixes: 966922f2 ("HID: fix a crash in hid_report_raw_event() function.") Signed-off-by:
-
Mika Westerberg authored
commit 2ba33a4e upstream. ACPI Generic Address Structure (GAS) access_width field is not in bytes as the driver seems to expect in few places so fix this by using the newly introduced macro ACPI_ACCESS_BYTE_WIDTH(). Fixes: b1abf6fc ("ACPI / watchdog: Fix off-by-one error at resource assignment") Fixes: 058dfc76 ("ACPI / watchdog: Add support for WDAT hardware watchdog") Reported-by:
Jean Delvare <jdelvare@suse.de> Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Mika Westerberg authored
commit 1dade3a7 upstream. Sometimes it is useful to find the access_width field value in bytes and not in bits so add a helper that can be used for this purpose. Suggested-by:
-
Paul Moore authored
commit 2ad3e17e upstream. Commit 219ca394 ("audit: use union for audit_field values since they are mutually exclusive") combined a number of separate fields in the audit_field struct into a single union. Generally this worked just fine because they are generally mutually exclusive. Unfortunately in audit_data_to_entry() the overlap can be a problem when a specific error case is triggered that causes the error path code to attempt to cleanup an audit_field struct and the cleanup involves attempting to free a stored LSM string (the lsm_str field). Currently the code always has a non-NULL value in the audit_field.lsm_str field as the top of the for-loop transfers a value into audit_field.val (both .lsm_str and .val are part of the same union); if audit_data_to_entry() fails and the audit_field struct is specified to contain a LSM string, but the audit_field.lsm_str has not yet been properly set, the error handling code will attempt to free the bogus audit_field.lsm_str value that was set with audit_field.val at the top of the for-loop. This patch corrects this by ensuring that the audit_field.val is only set when needed (it is cleared when the audit_field struct is allocated with kcalloc()). It also corrects a few other issues to ensure that in case of error the proper error code is returned. Cc: stable@vger.kernel.org Fixes: 219ca394 ("audit: use union for audit_field values since they are mutually exclusive") Reported-by: syzbot+1f4d90ead370d72e450b@syzkaller.appspotmail.com Signed-off-by:
-
Dan Carpenter authored
commit 37b0b6b8 upstream. If sbi->s_flex_groups_allocated is zero and the first allocation fails then this code will crash. The problem is that "i--" will set "i" to -1 but when we compare "i >= sbi->s_flex_groups_allocated" then the -1 is type promoted to unsigned and becomes UINT_MAX. Since UINT_MAX is more than zero, the condition is true so we call kvfree(new_groups[-1]). The loop will carry on freeing invalid memory until it crashes. Fixes: 7c990728 ("ext4: fix potential race between s_flex_groups online resizing and access") Reviewed-by:
Suraj Jitindar Singh <surajjs@amazon.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Jason Baron authored
[ Upstream commit 8a9093c7 ] tc flower rules that are based on src or dst port blocking are sometimes ineffective due to uninitialized stack data. __skb_flow_dissect() extracts ports from the skb for tc flower to match against. However, the port dissection is not done when when the FLOW_DIS_IS_FRAGMENT bit is set in key_control->flags. All callers of __skb_flow_dissect(), zero-out the key_control field except for fl_classify() as used by the flower classifier. Thus, the FLOW_DIS_IS_FRAGMENT may be set on entry to __skb_flow_dissect(), since key_control is allocated on the stack and may not be initialized. Since key_basic and key_control are present for all flow keys, let's make sure they are initialized. Fixes: 62230715 ("flow_dissector: do not dissect l4 ports for fragments") Co-developed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
Jason Baron <jbaron@akamai.com> Signed-off-by:
-
Dmitry Osipenko authored
[ Upstream commit c3331d2f ] The PN544 driver checks the "enable" polarity during of driver's probe and it's doing that by turning ON and OFF NFC with different polarities until enabling succeeds. It takes some time for the hardware to power-down, and thus, to deassert the IRQ that is raised by turning ON the hardware. Since the delay after last power-down of the polarity-checking process is missed in the code, the interrupt may trigger immediately after installing the IRQ handler (right after the checking is done), which results in IRQ handler trying to touch the disabled HW and ends with marking NFC as 'DEAD' during of the driver's probe: pn544_hci_i2c 1-002a: NFC: nfc_en polarity : active high pn544_hci_i2c 1-002a: NFC: invalid len byte shdlc: llc_shdlc_recv_frame: NULL Frame -> link is dead This patch fixes the occasional NFC initialization failure on Nexus 7 device. Signed-off-by:
Dmitry Osipenko <digetx@gmail.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 245709ec ] When T2 timer is to be stopped, the asoc should also be deleted, otherwise, there will be no chance to call sctp_association_free and the asoc could last in memory forever. However, in sctp_sf_shutdown_sent_abort(), after adding the cmd SCTP_CMD_TIMER_STOP for T2 timer, it may return error due to the format error from __sctp_sf_do_9_1_abort() and miss adding SCTP_CMD_ASSOC_FAILED where the asoc will be deleted. This patch is to fix it by moving the format error check out of __sctp_sf_do_9_1_abort(), and do it before adding the cmd SCTP_CMD_TIMER_STOP for T2 timer. Thanks Hangbin for reporting this issue by the fuzz testing. v1->v2: - improve the comment in the code as Marcelo's suggestion. Fixes: 96ca468b ("sctp: check invalid value of length parameter in error cause") Reported-by:
Hangbin Liu <liuhangbin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Benjamin Poirier authored
[ Upstream commit e404b8c7 ] After commit 27596472 ("ipv6: fix ECMP route replacement") it is no longer possible to replace an ECMP-able route by a non ECMP-able route. For example, ip route add 2001:db8::1/128 via fe80::1 dev dummy0 ip route replace 2001:db8::1/128 dev dummy0 does not work as expected. Tweak the replacement logic so that point 3 in the log of the above commit becomes: 3. If the new route is not ECMP-able, and no matching non-ECMP-able route exists, replace matching ECMP-able route (if any) or add the new route. We can now summarize the entire replace semantics to: When doing a replace, prefer replacing a matching route of the same "ECMP-able-ness" as the replace argument. If there is no such candidate, fallback to the first route found. Fixes: 27596472 ("ipv6: fix ECMP route replacement") Signed-off-by:
Benjamin Poirier <bpoirier@cumulusnetworks.com> Reviewed-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
-
Benjamin Poirier authored
[ Upstream commit afecdb37 ] When splitting an RTA_MULTIPATH request into multiple routes and adding the second and later components, we must not simply remove NLM_F_REPLACE but instead replace it by NLM_F_CREATE. Otherwise, it may look like the netlink message was malformed. For example, ip route add 2001:db8::1/128 dev dummy0 ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 \ nexthop via fe80::30:2 dev dummy0 results in the following warnings: [ 1035.057019] IPv6: RTM_NEWROUTE with no NLM_F_CREATE or NLM_F_REPLACE [ 1035.057517] IPv6: NLM_F_CREATE should be set when creating new route This patch makes the nlmsg sequence look equivalent for __ip6_ins_rt() to what it would get if the multipath route had been added in multiple netlink operations: ip route add 2001:db8::1/128 dev dummy0 ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 ip route append 2001:db8::1/128 nexthop via fe80::30:2 dev dummy0 Fixes: 27596472 ("ipv6: fix ECMP route replacement") Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Arun Parameswaran authored
commit 6f08e98d upstream. The mii management register in iproc mdio block does not have a retention register so it is lost on suspend. Save and restore value of register while resuming from suspend. Fixes: bb1a6197 ("net: phy: Initialize mdio clock at probe function") Signed-off-by:
Arun Parameswaran <arun.parameswaran@broadcom.com> Signed-off-by:
Scott Branden <scott.branden@broadcom.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Jethro Beekman authored
[ Upstream commit 540e585a ] In 709772e6, RT_TABLE_COMPAT was added to allow legacy software to deal with routing table numbers >= 256, but the same change to FIB rule queries was overlooked. Signed-off-by:
Jethro Beekman <jethro@fortanix.com> Signed-off-by:
-
Petr Mladek authored
commit c3fee609 upstream. The commit 97f5f0cd ("Input: implement SysRq as a separate input handler") added pr_fmt() definition. It caused a duplicated message prefix in the sysrq header messages, for example: [ 177.053931] sysrq: SysRq : Show backtrace of all active CPUs [ 742.864776] sysrq: SysRq : HELP : loglevel(0-9) reboot(b) crash(c) Fixes: 97f5f0cd ("Input: implement SysRq as a separate input handler") Signed-off-by:
Petr Mladek <pmladek@suse.com> Reviewed-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by:
-
Petr Mladek authored
commit 075e1a0c upstream. The sysrq header line is printed with an increased loglevel to provide users some positive feedback. The original loglevel is not restored when the sysrq operation is disabled. This bug was introduced in 2.6.12 (pre-git-history) by the commit ("Allow admin to enable only some of the Magic-Sysrq functions"). Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Tommi Rantala <tommi.t.rantala@nokia.com> Signed-off-by:
-
Sergey Matyukevich authored
[ Upstream commit ea750801 ] The nl80211_policy is missing for NL80211_ATTR_STATUS_CODE attribute. As a result, for strictly validated commands, it's assumed to not be supported. Signed-off-by:
Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Link: https://lore.kernel.org/r/20200213131608.10541-2-sergey.matyukevich.os@quantenna.comSigned-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Frank Sorenson authored
[ Upstream commit f52aa79d ] A number of the debug statements output file or directory mode in hex. Change these to print using octal. Signed-off-by:
Frank Sorenson <sorenson@redhat.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Arthur Kiyanovski authored
[ Upstream commit c207979f ] comp_ctx can be NULL in a very rare case when an admin command is executed during the execution of ena_remove(). The bug scenario is as follows: * ena_destroy_device() sets the comp_ctx to be NULL * An admin command is executed before executing unregister_netdev(), this can still happen because our device can still receive callbacks from the netdev infrastructure such as ethtool commands. * When attempting to access the comp_ctx, the bug occurs since it's set to NULL Fix: Added a check that comp_ctx is not NULL Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by:
-
Arthur Kiyanovski authored
[ Upstream commit 92569fd2 ] The indirection table has the indices of the Rx queues. When we store it during set indirection operation, we convert the indices to our internal representation of the indices. Our internal representation of the indices is: even indices for Tx and uneven indices for Rx, where every Tx/Rx pair are in a consecutive order starting from 0. For example if the driver has 3 queues (3 for Tx and 3 for Rx) then the indices are as follows: 0 1 2 3 4 5 Tx Rx Tx Rx Tx Rx The BUG: The issue is that when we satisfy a get request for the indirection table, we don't convert the indices back to the original representation. The FIX: Simply apply the inverse function for the indices of the indirection table after we set it. Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by:
-
Arthur Kiyanovski authored
[ Upstream commit 4844470d ] The device receives, stores and retrieves the hash function value as bits and not as their enum value. The bug: * In ena_com_set_hash_function() we set cmd.u.flow_hash_func.selected_func to the bit value of rss->hash_func. (1 << rss->hash_func) * In ena_com_get_hash_function() we retrieve the hash function and store it's bit value in rss->hash_func. (Now the bit value of rss->hash_func is stored in rss->hash_func instead of it's enum value) The fix: This commit fixes the issue by converting the retrieved hash function values from the device to the matching enum value of the set bit using ffs(). ffs() finds the first set bit's index in a word. Since the function returns 1 for the LSB's index, we need to subtract 1 from the returned value (note that BIT(0) is 1). Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by:
-
Sameeh Jubran authored
[ Upstream commit 0c8923c0 ] On old hardware, getting / setting the hash function is not supported while gettting / setting the indirection table is. This commit enables us to still show the indirection table on older hardwares by setting the hash function and key to NULL. Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by:
-
