When creating the second host in h2_create(), two addresses are assigned
to the interface, but only one is deleted. When running the test twice
in a row the following error is observed:

$ ./router_bridge_vlan.sh
TEST: ping                                                          [ OK ]
TEST: ping6                                                         [ OK ]
TEST: vlan                                                          [ OK ]
$ ./router_bridge_vlan.sh
RTNETLINK answers: File exists
TEST: ping                                                          [ OK ]
TEST: ping6                                                         [ OK ]
TEST: vlan                                                          [ OK ]

Fix this by deleting the address during cleanup.

Fixes: 5b1e7f9e ("selftests: forwarding: Test routed bridge interface")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case the driver vetoes the addition of an IPv6 multipath route, the
IPv6 stack will emit delete notifications for the sibling routes that
were already added to the FIB trie. Since these siblings are not present
in hardware, a warning will be generated.

Have the driver ignore notifications for routes it does not have.

Fixes: ebee3cad ("ipv6: Add IPv6 multipath notifications for add / replace")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzbot found a crash:

  BUG: KMSAN: uninit-value in crc32_body lib/crc32.c:112 [inline]
  BUG: KMSAN: uninit-value in crc32_le_generic lib/crc32.c:179 [inline]
  BUG: KMSAN: uninit-value in __crc32c_le_base+0x4fa/0xd30 lib/crc32.c:202
  Call Trace:
    crc32_body lib/crc32.c:112 [inline]
    crc32_le_generic lib/crc32.c:179 [inline]
    __crc32c_le_base+0x4fa/0xd30 lib/crc32.c:202
    chksum_update+0xb2/0x110 crypto/crc32c_generic.c:90
    crypto_shash_update+0x4c5/0x530 crypto/shash.c:107
    crc32c+0x150/0x220 lib/libcrc32c.c:47
    sctp_csum_update+0x89/0xa0 include/net/sctp/checksum.h:36
    __skb_checksum+0x1297/0x12a0 net/core/skbuff.c:2640
    sctp_compute_cksum include/net/sctp/checksum.h:59 [inline]
    sctp_packet_pack net/sctp/output.c:528 [inline]
    sctp_packet_transmit+0x40fb/0x4250 net/sctp/output.c:597
    sctp_outq_flush_transports net/sctp/outqueue.c:1146 [inline]
    sctp_outq_flush+0x1823/0x5d80 net/sctp/outqueue.c:1194
    sctp_outq_uncork+0xd0/0xf0 net/sctp/outqueue.c:757
    sctp_cmd_interpreter net/sctp/sm_sideeffect.c:1781 [inline]
    sctp_side_effects net/sctp/sm_sideeffect.c:1184 [inline]
    sctp_do_sm+0x8fe1/0x9720 net/sctp/sm_sideeffect.c:1155
    sctp_primitive_REQUESTHEARTBEAT+0x175/0x1a0 net/sctp/primitive.c:185
    sctp_apply_peer_addr_params+0x212/0x1d40 net/sctp/socket.c:2433
    sctp_setsockopt_peer_addr_params net/sctp/socket.c:2686 [inline]
    sctp_setsockopt+0x189bb/0x19090 net/sctp/socket.c:4672

The issue was caused by transport->ipaddr set with uninit addr param, which
was passed by:

  sctp_transport_init net/sctp/transport.c:47 [inline]
  sctp_transport_new+0x248/0xa00 net/sctp/transport.c:100
  sctp_assoc_add_peer+0x5ba/0x2030 net/sctp/associola.c:611
  sctp_process_param net/sctp/sm_make_chunk.c:2524 [inline]

where 'addr' is set by sctp_v4_from_addr_param(), and it doesn't initialize
the padding of addr->v4.

Later when calling sctp_make_heartbeat(), hbinfo.daddr(=transport->ipaddr)
will become the part of skb, and the issue occurs.

This patch is to fix it by initializing the padding of addr->v4 in
sctp_v4_from_addr_param(), as well as other functions that do the similar
thing, and these functions shouldn't trust that the caller initializes the
memory, as Marcelo suggested.

Reported-by: syzbot+6dcbfea81cd3d4dd0b02@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) syzbot reported an uninit-value in bond_neigh_setup() [1]

 bond_neigh_setup() uses a temporary on-stack 'struct neigh_parms parms',
 but only clears parms.neigh_setup field.

 A stacked bonding device would then enter bond_neigh_setup()
 and read garbage from parms->dev.

 If we get really unlucky and garbage is matching @dev, then we
 could recurse and eventually crash.

 Let's make sure the whole structure is cleared to avoid surprises.

2) bond_neigh_setup() can be called while another cpu manipulates
 the master device, removing or adding a slave.
 We need at least rcu protection to prevent use-after-free.

Note: Prior code does not support a stack of bonding devices,
      this patch does not attempt to fix this, and leave a comment instead.

[1]

BUG: KMSAN: uninit-value in bond_neigh_setup+0xa4/0x110 drivers/net/bonding/bond_main.c:3655
CPU: 0 PID: 11256 Comm: syz-executor.0 Not tainted 5.4.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 <IRQ>
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c9/0x220 lib/dump_stack.c:118
 kmsan_report+0x128/0x220 mm/kmsan/kmsan_report.c:108
 __msan_warning+0x57/0xa0 mm/kmsan/kmsan_instr.c:245
 bond_neigh_setup+0xa4/0x110 drivers/net/bonding/bond_main.c:3655
 bond_neigh_init+0x216/0x4b0 drivers/net/bonding/bond_main.c:3626
 ___neigh_create+0x169e/0x2c40 net/core/neighbour.c:613
 __neigh_create+0xbd/0xd0 net/core/neighbour.c:674
 ip6_finish_output2+0x149a/0x2670 net/ipv6/ip6_output.c:113
 __ip6_finish_output+0x83d/0x8f0 net/ipv6/ip6_output.c:142
 ip6_finish_output+0x2db/0x420 net/ipv6/ip6_output.c:152
 NF_HOOK_COND include/linux/netfilter.h:294 [inline]
 ip6_output+0x5d3/0x720 net/ipv6/ip6_output.c:175
 dst_output include/net/dst.h:436 [inline]
 NF_HOOK include/linux/netfilter.h:305 [inline]
 mld_sendpack+0xebd/0x13d0 net/ipv6/mcast.c:1682
 mld_send_cr net/ipv6/mcast.c:1978 [inline]
 mld_ifc_timer_expire+0x116b/0x1680 net/ipv6/mcast.c:2477
 call_timer_fn+0x232/0x530 kernel/time/timer.c:1404
 expire_timers kernel/time/timer.c:1449 [inline]
 __run_timers+0xd60/0x1270 kernel/time/timer.c:1773
 run_timer_softirq+0x2d/0x50 kernel/time/timer.c:1786
 __do_softirq+0x4a1/0x83a kernel/softirq.c:293
 invoke_softirq kernel/softirq.c:375 [inline]
 irq_exit+0x230/0x280 kernel/softirq.c:416
 exiting_irq+0xe/0x10 arch/x86/include/asm/apic.h:536
 smp_apic_timer_interrupt+0x48/0x70 arch/x86/kernel/apic/apic.c:1138
 apic_timer_interrupt+0x2e/0x40 arch/x86/entry/entry_64.S:835
 </IRQ>
RIP: 0010:kmsan_free_page+0x18d/0x1c0 mm/kmsan/kmsan_shadow.c:439
Code: 4c 89 ff 44 89 f6 e8 82 0d ee ff 65 ff 0d 9f 26 3b 60 65 8b 05 98 26 3b 60 85 c0 75 24 e8 5b f6 35 ff 4c 89 6d d0 ff 75 d0 9d <48> 83 c4 10 5b 41 5c 41 5d 41 5e 41 5f 5d c3 0f 0b 0f 0b 0f 0b 0f
RSP: 0018:ffffb328034af818 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff13
RAX: 0000000000000000 RBX: ffffe2d7471f8360 RCX: 0000000000000000
RDX: ffffffffadea7000 RSI: 0000000000000004 RDI: ffff93496fcda104
RBP: ffffb328034af850 R08: ffff934a47e86d00 R09: ffff93496fc41900
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001
R13: 0000000000000246 R14: 0000000000000000 R15: ffffe2d7472225c0
 free_pages_prepare mm/page_alloc.c:1138 [inline]
 free_pcp_prepare mm/page_alloc.c:1230 [inline]
 free_unref_page_prepare+0x1d9/0x770 mm/page_alloc.c:3025
 free_unref_page mm/page_alloc.c:3074 [inline]
 free_the_page mm/page_alloc.c:4832 [inline]
 __free_pages+0x154/0x230 mm/page_alloc.c:4840
 __vunmap+0xdac/0xf20 mm/vmalloc.c:2277
 __vfree mm/vmalloc.c:2325 [inline]
 vfree+0x7c/0x170 mm/vmalloc.c:2355
 copy_entries_to_user net/ipv6/netfilter/ip6_tables.c:883 [inline]
 get_entries net/ipv6/netfilter/ip6_tables.c:1041 [inline]
 do_ip6t_get_ctl+0xfa4/0x1030 net/ipv6/netfilter/ip6_tables.c:1709
 nf_sockopt net/netfilter/nf_sockopt.c:104 [inline]
 nf_getsockopt+0x481/0x4e0 net/netfilter/nf_sockopt.c:122
 ipv6_getsockopt+0x264/0x510 net/ipv6/ipv6_sockglue.c:1400
 tcp_getsockopt+0x1c6/0x1f0 net/ipv4/tcp.c:3688
 sock_common_getsockopt+0x13f/0x180 net/core/sock.c:3110
 __sys_getsockopt+0x533/0x7b0 net/socket.c:2129
 __do_sys_getsockopt net/socket.c:2144 [inline]
 __se_sys_getsockopt+0xe1/0x100 net/socket.c:2141
 __x64_sys_getsockopt+0x62/0x80 net/socket.c:2141
 do_syscall_64+0xb6/0x160 arch/x86/entry/common.c:291
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x45d20a
Code: b8 34 01 00 00 0f 05 48 3d 01 f0 ff ff 0f 83 8d 8b fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 49 89 ca b8 37 00 00 00 0f 05 <48> 3d 01 f0 ff ff 0f 83 6a 8b fb ff c3 66 0f 1f 84 00 00 00 00 00
RSP: 002b:0000000000a6f618 EFLAGS: 00000212 ORIG_RAX: 0000000000000037
RAX: ffffffffffffffda RBX: 0000000000a6f640 RCX: 000000000045d20a
RDX: 0000000000000041 RSI: 0000000000000029 RDI: 0000000000000003
RBP: 0000000000717cc0 R08: 0000000000a6f63c R09: 0000000000004000
R10: 0000000000a6f740 R11: 0000000000000212 R12: 0000000000000003
R13: 0000000000000000 R14: 0000000000000029 R15: 0000000000715b00

Local variable description: ----parms@bond_neigh_init
Variable was created at:
 bond_neigh_init+0x8c/0x4b0 drivers/net/bonding/bond_main.c:3617
 bond_neigh_init+0x8c/0x4b0 drivers/net/bonding/bond_main.c:3617

Fixes: 9918d5bf ("bonding: modify only neigh_parms owned by us")
Fixes: 234bcf8a ("net/bonding: correctly proxy slave neigh param setup ndo function")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

neigh_cleanup() has not been used for seven years, and was a wrong design.

Messing with shared pointer in bond_neigh_init() without proper
memory barriers would at least trigger syzbot complains eventually.

It is time to remove this stuff.

Fixes: b63b70d8 ("IPoIB: Use a private hash table for path lookup in xmit path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.5-20191208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2019-12-08

this is a pull request of 13 patches for net/master.

The first two patches are by Dan Murphy. He adds himself as a maintainer to the
m-can MMIO and tcan SPI driver.

The next two patches the j1939 stack. The first one is by Oleksij Rempel and
fixes a locking problem found by the syzbot, the second one is by me an fixes a
mistake in the documentation.

Srinivas Neeli fixes missing RX CAN packets on CANFD2.0 in the xilinx driver.

Sean Nyekjaer fixes a possible deadlock in the the flexcan driver after
suspend/resume. Joakim Zhang contributes two patches for the flexcan driver
that fix problems with the low power enter/exit.

The next 4 patches all target the tcan part of the m_can driver. Sean Nyekjaer
adds the required delay after reset and fixes the device tree binding example.
Dan Murphy's patches make the wake-gpio optional.

In the last patch Xiaolong Huang fixes several kernel memory info leaks to the
USB device in the kvaser_usb_leaf driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) More jumbo frame fixes in r8169, from Heiner Kallweit.

 2) Fix bpf build in minimal configuration, from Alexei Starovoitov.

 3) Use after free in slcan driver, from Jouni Hogander.

 4) Flower classifier port ranges don't work properly in the HW offload
    case, from Yoshiki Komachi.

 5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.

 6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.

 7) Fix flow dissection in dsa TX path, from Alexander Lobakin.

 8) Stale syncookie timestampe fixes from Guillaume Nault.

[ Did an evil merge to silence a warning introduced by this pull - Linus ]

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  r8169: fix rtl_hw_jumbo_disable for RTL8168evl
  net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
  r8169: add missing RX enabling for WoL on RTL8125
  vhost/vsock: accept only packets with the right dst_cid
  net: phy: dp83867: fix hfs boot in rgmii mode
  net: ethernet: ti: cpsw: fix extra rx interrupt
  inet: protect against too small mtu values.
  gre: refetch erspan header from skb->data after pskb_may_pull()
  pppoe: remove redundant BUG_ON() check in pppoe_pernet
  tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
  tcp: tighten acceptance of ACKs not matching a child socket
  tcp: fix rejected syncookies due to stale timestamps
  lpc_eth: kernel BUG on remove
  tcp: md5: fix potential overestimation of TCP option space
  net: sched: allow indirect blocks to bind to clsact in TC
  net: core: rename indirect block ingress cb function
  net-sysfs: Call dev_hold always in netdev_queue_add_kobject
  net: dsa: fix flow dissection on Tx path
  net/tls: Fix return values to avoid ENOTSUPP
  net: avoid an indirect call in ____sys_recvmsg()
  ...

Pull more SCSI updates from James Bottomley:
 "Eleven patches, all in drivers (no core changes) that are either minor
  cleanups or small fixes.

  They were late arriving, but still safe for -rc1"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
  scsi: megaraid_sas: Make poll_aen_lock static
  scsi: sd_zbc: Improve report zones error printout
  scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
  scsi: qla2xxx: unregister ports after GPN_FT failure
  scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
  scsi: pm80xx: Remove unused include of linux/version.h
  scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
  scsi: scsi_transport_sas: Fix memory leak when removing devices
  scsi: lpfc: size cpu map by last cpu id set
  scsi: ibmvscsi_tgt: Remove unneeded variable rc

Pull cifs fixes from Steve French:
 "Nine cifs/smb3 fixes:

   - one fix for stable (oops during oplock break)

   - two timestamp fixes including important one for updating mtime at
     close to avoid stale metadata caching issue on dirty files (also
     improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the
     wire)

   - two fixes for "modefromsid" mount option for file create (now
     allows mode bits to be set more atomically and accurately on create
     by adding "sd_context" on create when modefromsid specified on
     mount)

   - two fixes for multichannel found in testing this week against
     different servers

   - two small cleanup patches"

* tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: improve check for when we send the security descriptor context on create
  smb3: fix mode passed in on create for modetosid mount option
  cifs: fix possible uninitialized access and race on iface_list
  cifs: Fix lookup of SMB connections on multichannel
  smb3: query attributes on file close
  smb3: remove unused flag passed into close functions
  cifs: remove redundant assignment to pointer pneg_ctxt
  fs: cifs: Fix atime update check vs mtime
  CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks

Pull misc vfs cleanups from Al Viro:
 "No common topic, just three cleanups".

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  make __d_alloc() static
  fs/namespace: add __user to open_tree and move_mount syscalls
  fs/fnctl: fix missing __user in fcntl_rw_hint()

Uninitialized Kernel memory can leak to USB devices.

Fix this by using kzalloc() instead of kmalloc().
Signed-off-by: Xiaolong Huang <butterflyhuangxx@gmail.com>
Fixes: 7259124e ("can: kvaser_usb: Split driver into kvaser_usb_core.c and kvaser_usb_leaf.c")
Cc: linux-stable <stable@vger.kernel.org> # >= v4.19
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The device has the ability to disable the wake-up pin option. The
wake-up pin can be either force to GND or Vsup and does not have to be
tied to a GPIO. In order for the device to not use the wake-up feature
write the register to disable the WAKE_CONFIG option.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Cc: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The wake-up of the device can be configured as an optional feature of
the device. Move the wake-up gpio from a requried property to an
optional property.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Cc: Rob Herring <robh@kernel.org>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Change the reset pin example to active high to be in line with
the datasheet
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

According to section "8.3.8 RST Pin" in the datasheet we are required to
wait >700us after the device is reset.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Stop Mode is entered when Stop Mode is requested at chip level and
MCR[LPM_ACK] is asserted by the FlexCAN.

Double check with IP owner, the MCR[LPM_ACK] bit should be polled for
stop mode acknowledgment, not the acknowledgment from chip level which
is used to gate flexcan clocks.

This patch depends on:

    b7603d08 ("can: flexcan: add low power enter/exit acknowledgment helper")

Fixes: 5f186c25 (can: flexcan: fix stop mode acknowledgment)
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The MCR[LPMACK] read-only bit indicates that FlexCAN is in a lower-power
mode (Disabled mode, Doze mode, Stop mode).

The CPU can poll this bit to know when FlexCAN has actually entered low
power mode. The low power enter/exit acknowledgment helper will reduce
code duplication for disabled mode, doze mode and stop mode.
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

When suspending, and there is still CAN traffic on the interfaces the
flexcan immediately wakes the platform again. As it should :-). But it
throws this error msg:

[ 3169.378661] PM: noirq suspend of devices failed

On the way down to suspend the interface that throws the error message
calls flexcan_suspend() but fails to call flexcan_noirq_suspend(). That
means flexcan_enter_stop_mode() is called, but on the way out of suspend
the driver only calls flexcan_resume() and skips flexcan_noirq_resume(),
thus it doesn't call flexcan_exit_stop_mode(). This leaves the flexcan
in stop mode, and with the current driver it can't recover from this
even with a soft reboot, it requires a hard reboot.

This patch fixes the deadlock when using self wakeup, by calling
flexcan_exit_stop_mode() from flexcan_resume() instead of
flexcan_noirq_resume().

This also fixes another issue: CAN frames are received out-of-order in
first IRQ handler run after wakeup.

The problem is that the wakeup latency from frame reception to the IRQ
handler (where the CAN frames are sorted by timestamp) is much bigger
than the time stamp counter wrap around time. This means it's
impossible to sort the CAN frames by timestamp.

The reason is that the controller exits stop mode during noirq resume,
which means it receives frames immediately, but interrupt handling is
still not possible.

So exit stop mode during resume stage instead of noirq resume fixes this
issue.

Fixes: de3578c1 ("can: flexcan: add self wakeup support")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

CANFD2.0 core uses BRAM for storing acceptance filter ID(AFID) and MASK
(AFMASK)registers. So by default AFID and AFMASK registers contain random
data. Due to random data, we are not able to receive all CAN ids.

Initializing AFID and AFMASK registers with Zero before enabling
acceptance filter to receive all packets irrespective of ID and Mask.

Fixes: 0db90713 ("can: xilinx: add can 2.0 support")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

During development the define J1939_PGN_ADDRESS_REQUEST was renamed to
J1939_PGN_REQUEST. It was forgotten to adjust the documentation
accordingly.

This patch fixes the name of the symbol.

Reported-by: https://github.com/linux-can/can-utils/issues/159#issuecomment-556538798
Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

syzbot reproduced following crash:

===============================================================================
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 9844 Comm: syz-executor.0 Not tainted 5.4.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:__lock_acquire+0x1254/0x4a00 kernel/locking/lockdep.c:3828
Code: 00 0f 85 96 24 00 00 48 81 c4 f0 00 00 00 5b 41 5c 41 5d 41 5e 41
5f 5d c3 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1 ea 03 <80> 3c 02
00 0f 85 0b 28 00 00 49 81 3e 20 19 78 8a 0f 84 5f ee ff
RSP: 0018:ffff888099c3fb48 EFLAGS: 00010006
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000218 RSI: 0000000000000000 RDI: 0000000000000001
RBP: ffff888099c3fc60 R08: 0000000000000001 R09: 0000000000000001
R10: fffffbfff146e1d0 R11: ffff888098720400 R12: 00000000000010c0
R13: 0000000000000000 R14: 00000000000010c0 R15: 0000000000000000
FS:  00007f0559e98700(0000) GS:ffff8880ae800000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe4d89e0000 CR3: 0000000099606000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 lock_acquire+0x190/0x410 kernel/locking/lockdep.c:4485
 __raw_spin_lock_bh include/linux/spinlock_api_smp.h:135 [inline]
 _raw_spin_lock_bh+0x33/0x50 kernel/locking/spinlock.c:175
 spin_lock_bh include/linux/spinlock.h:343 [inline]
 j1939_jsk_del+0x32/0x210 net/can/j1939/socket.c:89
 j1939_sk_bind+0x2ea/0x8f0 net/can/j1939/socket.c:448
 __sys_bind+0x239/0x290 net/socket.c:1648
 __do_sys_bind net/socket.c:1659 [inline]
 __se_sys_bind net/socket.c:1657 [inline]
 __x64_sys_bind+0x73/0xb0 net/socket.c:1657
 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x45a679
Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89
f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01
f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f0559e97c78 EFLAGS: 00000246 ORIG_RAX: 0000000000000031
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 000000000045a679
RDX: 0000000000000018 RSI: 0000000020000240 RDI: 0000000000000003
RBP: 000000000075bf20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f0559e986d4
R13: 00000000004c09e9 R14: 00000000004d37d0 R15: 00000000ffffffff
Modules linked in:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 9844 at kernel/locking/mutex.c:1419
mutex_trylock+0x279/0x2f0 kernel/locking/mutex.c:1427
===============================================================================

This issues was caused by null pointer deference. Where j1939_sk_bind()
was using currently not existing priv.

Possible scenario may look as following:
cpu0                                    cpu1
bind()
                                        bind()
 j1939_sk_bind()
                                         j1939_sk_bind()
  priv = jsk->priv;
                                         priv = jsk->priv;
  lock_sock(sock->sk);
  priv = j1939_netdev_start(ndev);
  j1939_jsk_add(priv, jsk);
    jsk->priv = priv;
  relase_sock(sock->sk);
                                         lock_sock(sock->sk);
                                         j1939_jsk_del(priv, jsk);
                                         ..... ooops ......

With this patch we move "priv = jsk->priv;" after the lock, to avoid
assigning of wrong priv pointer.

Reported-by: syzbot+99e9e1b200a1e363237d@syzkaller.appspotmail.com
Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Adding myself to support the TI TCAN4X5X SPI CAN device.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since I refactored the code to create a m_can framework and we
have a MMIO MCAN IP as well add myself to help maintain the code.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull NTB update from Jon Mason:
 "Just a simple patch to add a new Hygon Device ID to the AMD NTB device
  driver"

* tag 'ntb-5.5' of git://github.com/jonmason/ntb:
  NTB: Add Hygon Device ID

Pull more input updates from Dmitry Torokhov:

 - fixups for Synaptics RMI4 driver

 - a quirk for Goodinx touchscreen on Teclast tablet

 - a new keycode definition for activating privacy screen feature found
   on a few "enterprise" laptops

 - updates to snvs_pwrkey driver

 - polling uinput device for writing (which is always allowed) now works

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers
  Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash
  Input: goodix - add upside-down quirk for Teclast X89 tablet
  Input: add privacy screen toggle keycode
  Input: uinput - fix returning EPOLLOUT from uinput_poll
  Input: snvs_pwrkey - remove gratuitous NULL initializers
  Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q

Pull iomap fixes from Darrick Wong:
 "Fix a race condition and a use-after-free error:

   - Fix a UAF when reporting writeback errors

   - Fix a race condition when handling page uptodate on fragmented file
     with blocksize < pagesize"

* tag 'iomap-5.5-merge-14' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: stop using ioend after it's been freed in iomap_finish_ioend()
  iomap: fix sub-page uptodate handling

Pull xfs fixes from Darrick Wong:
 "Fix a couple of resource management errors and a hang:

   - fix a crash in the log setup code when log mounting fails

   - fix a hang when allocating space on the realtime device

   - fix a block leak when freeing space on the realtime device"

* tag 'xfs-5.5-merge-17' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix mount failure crash on invalid iclog memory access
  xfs: don't check for AG deadlock for realtime files in bunmapi
  xfs: fix realtime file data space leak

Pull orangefs update from Mike Marshall:
 "orangefs: posix open permission checking...

  Orangefs has no open, and orangefs checks file permissions on each
  file access. Posix requires that file permissions be checked on open
  and nowhere else. Orangefs-through-the-kernel needs to seem posix
  compliant.

  The VFS opens files, even if the filesystem provides no method. We can
  see if a file was successfully opened for read and or for write by
  looking at file->f_mode.

  When writes are flowing from the page cache, file is no longer
  available. We can trust the VFS to have checked file->f_mode before
  writing to the page cache.

  The mode of a file might change between when it is opened and IO
  commences, or it might be created with an arbitrary mode.

  We'll make sure we don't hit EACCES during the IO stage by using
  UID 0"

[ This is "posixish", but not a great solution in the long run, since a
  proper secure network server shouldn't really trust the client like this.
  But proper and secure POSIX behavior requires an open method and a
  resulting cookie for IO of some kind, or similar.    - Linus ]

* tag 'for-linus-5.5-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
  orangefs: posix open permission checking...

Pull nfsd updates from Bruce Fields:
 "This is a relatively quiet cycle for nfsd, mainly various bugfixes.

  Possibly most interesting is Trond's fixes for some callback races
  that were due to my incomplete understanding of rpc client shutdown.
  Unfortunately at the last minute I've started noticing a new
  intermittent failure to send callbacks. As the logic seems basically
  correct, I'm leaving Trond's patches in for now, and hope to find a
  fix in the next week so I don't have to revert those patches"

* tag 'nfsd-5.5' of git://linux-nfs.org/~bfields/linux: (24 commits)
  nfsd: depend on CRYPTO_MD5 for legacy client tracking
  NFSD fixing possible null pointer derefering in copy offload
  nfsd: check for EBUSY from vfs_rmdir/vfs_unink.
  nfsd: Ensure CLONE persists data and metadata changes to the target file
  SUNRPC: Fix backchannel latency metrics
  nfsd: restore NFSv3 ACL support
  nfsd: v4 support requires CRYPTO_SHA256
  nfsd: Fix cld_net->cn_tfm initialization
  lockd: remove __KERNEL__ ifdefs
  sunrpc: remove __KERNEL__ ifdefs
  race in exportfs_decode_fh()
  nfsd: Drop LIST_HEAD where the variable it declares is never used.
  nfsd: document callback_wq serialization of callback code
  nfsd: mark cb path down on unknown errors
  nfsd: Fix races between nfsd4_cb_release() and nfsd4_shutdown_callback()
  nfsd: minor 4.1 callback cleanup
  SUNRPC: Fix svcauth_gss_proxy_init()
  SUNRPC: Trace gssproxy upcall results
  sunrpc: fix crash when cache_head become valid before update
  nfsd: remove private bin2hex implementation
  ...

Pull NFS client updates from Trond Myklebust:
 "Highlights include:

  Features:

   - NFSv4.2 now supports cross device offloaded copy (i.e. offloaded
     copy of a file from one source server to a different target
     server).

   - New RDMA tracepoints for debugging congestion control and Local
     Invalidate WRs.

  Bugfixes and cleanups

   - Drop the NFSv4.1 session slot if nfs4_delegreturn_prepare waits for
     layoutreturn

   - Handle bad/dead sessions correctly in nfs41_sequence_process()

   - Various bugfixes to the delegation return operation.

   - Various bugfixes pertaining to delegations that have been revoked.

   - Cleanups to the NFS timespec code to avoid unnecessary conversions
     between timespec and timespec64.

   - Fix unstable RDMA connections after a reconnect

   - Close race between waking an RDMA sender and posting a receive

   - Wake pending RDMA tasks if connection fails

   - Fix MR list corruption, and clean up MR usage

   - Fix another RPCSEC_GSS issue with MIC buffer space"

* tag 'nfs-for-5.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (79 commits)
  SUNRPC: Capture completion of all RPC tasks
  SUNRPC: Fix another issue with MIC buffer space
  NFS4: Trace lock reclaims
  NFS4: Trace state recovery operation
  NFSv4.2 fix memory leak in nfs42_ssc_open
  NFSv4.2 fix kfree in __nfs42_copy_file_range
  NFS: remove duplicated include from nfs4file.c
  NFSv4: Make _nfs42_proc_copy_notify() static
  NFS: Fallocate should use the nfs4_fattr_bitmap
  NFS: Return -ETXTBSY when attempting to write to a swapfile
  fs: nfs: sysfs: Remove NULL check before kfree
  NFS: remove unneeded semicolon
  NFSv4: add declaration of current_stateid
  NFSv4.x: Drop the slot if nfs4_delegreturn_prepare waits for layoutreturn
  NFSv4.x: Handle bad/dead sessions correctly in nfs41_sequence_process()
  nfsv4: Move NFSPROC4_CLNT_COPY_NOTIFY to end of list
  SUNRPC: Avoid RPC delays when exiting suspend
  NFS: Add a tracepoint in nfs_fh_to_dentry()
  NFSv4: Don't retry the GETATTR on old stateid in nfs4_delegreturn_done()
  NFSv4: Handle NFS4ERR_OLD_STATEID in delegreturn
  ...

We had cases in the previous patch where we were sending the security
descriptor context on SMB3 open (file create) in cases when we hadn't
mounted with with "modefromsid" mount option.

Add check for that mount flag before calling ad_sd_context in
open init.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>

Pull VFIO updates from Alex Williamson:

 - Remove hugepage checks for reserved pfns (Ben Luo)

 - Fix irq-bypass unregister ordering (Jiang Yi)

* tag 'vfio-v5.5-rc1' of git://github.com/awilliam/linux-vfio:
  vfio/pci: call irq_bypass_unregister_producer() before freeing irq
  vfio/type1: remove hugepage checks in is_invalid_reserved_pfn()

Pull more xen updates from Juergen Gross:

 - a patch to fix a build warning

 - a cleanup of no longer needed code in the Xen event handling

 - a small series for the Xen grant driver avoiding high order
   allocations and replacing an insane global limit by a per-call one

 - a small series fixing Xen frontend/backend module referencing

* tag 'for-linus-5.5b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen-blkback: allow module to be cleanly unloaded
  xen/xenbus: reference count registered modules
  xen/gntdev: switch from kcalloc() to kvcalloc()
  xen/gntdev: replace global limit of mapped pages by limit per call
  xen/gntdev: remove redundant non-zero check on ret
  xen/events: remove event handling recursion detection

Merge misc Kconfig updates from Andrew Morton:
 "A number of changes to Kconfig files under lib/ from Changbin Du and
  Krzysztof Kozlowski"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  lib/: fix Kconfig indentation
  kernel-hacking: move DEBUG_FS to 'Generic Kernel Debugging Instruments'
  kernel-hacking: move DEBUG_BUGVERBOSE to 'printk and dmesg options'
  kernel-hacking: create a submenu for scheduler debugging options
  kernel-hacking: move SCHED_STACK_END_CHECK after DEBUG_STACK_USAGE
  kernel-hacking: move Oops into 'Lockups and Hangs'
  kernel-hacking: move kernel testing and coverage options to same submenu
  kernel-hacking: group kernel data structures debugging together
  kernel-hacking: create submenu for arch special debugging options
  kernel-hacking: group sysrq/kgdb/ubsan into 'Generic Kernel Debugging Instruments'

In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().

v2: fix referenced commit id

Fixes: 14012c9f ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pipe_wait() may be simple, but since it relies on the pipe lock, it
means that we have to do the wakeup while holding the lock.  That's
unfortunate, because the very first thing the waked entity will want to
do is to get the pipe lock for itself.

So get rid of the pipe_wait() usage by simply releasing the pipe lock,
doing the wakeup (if required) and then using wait_event_interruptible()
to wait on the right condition instead.

wait_event_interruptible() handles races on its own by comparing the
wakeup condition before and after adding itself to the wait queue, so
you can use an optimistic unlocked condition for it.

Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Jiasen Lin <linjiasen@hygon.cn>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

This code is ancient, and goes back to when we only had a single page
for the pipe buffers.  The exact history is hidden in the mists of time
(ie "before git", and in fact predates the BK repository too).

At that long-ago point in time, it actually helped to try to merge big
back-and-forth pipe reads and writes, and not limit pipe reads to the
single pipe buffer in length just because that was all we had at a time.

However, since then we've expanded the pipe buffers to multiple pages,
and this logic really doesn't seem to make sense.  And a lot of it is
somewhat questionable (ie "hmm, the user asked for a non-blocking read,
but we see that there's a writer pending, so let's wait anyway to get
the extra data that the writer will have").

But more importantly, it makes the "go to sleep" logic much less
obvious, and considering the wakeup issues we've had, I want to make for
less of those kinds of things.

Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is the read side version of the previous commit: it simplifies the
logic to only wake up waiting writers when necessary, and makes sure to
use a synchronous wakeup.  This time not so much for GNU make jobserver
reasons (that pipe never fills up), but simply to get the writer going
quickly again.

A bit less verbose commentary this time, if only because I assume that
the write side commentary isn't going to be ignored if you touch this
code.

Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>