Declare the fixed 65MHz pixel clock connected to the DU clock input.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

While the LEDs on r8a73a4/ape6evm are tied to VSUPPLY, they're driven by
an N-channel MOSFET. Hence the GPIO signal should be active high.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add DT nodes for the ADV7511 HDMI encoder and its HDMI output connector.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

HSUSB uses hp_clk rather than mp_clk for H/W register access.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[horms: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

HSUSB uses hp_clk rather than mp_clk for H/W register access.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[horms: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

r8a7791 SDHI ch0/ch1 has SD_DMACR which is located in 0x324.
This patch updates register size
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

r8a7790 SDHI ch0/ch1 has SD_DMACR which is located in 0x324.
This patch updates register size
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add references to the transmit and receive DMA channels in the three
SDHI nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add references to the transmit and receive DMA channels in the four
SDHI nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A7794 parts of the SDHI[012] device nodes.

Based on the orginal patch by Shinobu Uehara <shinobu.uehara.xc@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the ADSP clocks to the CPG and MSTP5 nodes of the R8A7790 device tree.

Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the ADSP clocks to the CPG and MSTP5 nodes of the R8A7791 device tree.

Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the Henninger board dependent part of the CAN0 device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A7791 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin.  Describe those clocks in the device
tree,  along with  the USB_EXTAL clock  from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A7790 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin.  Describe those clocks in the device
tree,  along with  the USB_EXTAL clock  from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Configure the pinmux on kzm9d to use the serial connector for uart1.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

With this information all GPIOs can make use of the PFC functionality.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Documentation says the last register is at 0x184 (CAxCPUCMCR), so use
proper length. Current APMU code accesses CAxCPUnCR which is currently
outside of the remapped area.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Documentation says the last register is at 0x184 (CAxCPUCMCR), so use
proper length. Current APMU code accesses CAxCPUnCR which is currently
outside of the remapped area.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add DT nodes for the ADV7511 HDMI encoder and its HDMI output connector
and configure the DISP pin group that drives the HDMI transmitter DE
pin.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.

Fixes: 59e79895 ("ARM: shmobile: r8a7791: Add clocks")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>

* Correct base address of SD3 div6 clk.
* Update div6 clock node labels
  There appears to have been some inconsistency and confusion here as on
  the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
  the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.

This has no run-time affect as the clock nodes are not currently used.

Fixes: 8e181633 ("ARM: shmobile: r8a7794: Add SDHI clocks to device tree")
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>

Enable the ethernet controller for the Alt board. Pin muxing entries are
currently left out as r8a7794 pin control support isn't available yet.
We thus rely on the boot loader to configure ethernet pins for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a DT node for the on-SoC ethernet controller device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the six IPMMU instances found in the r8a7794 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the seven IPMMU instances found in the r8a7791 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the six IPMMU instances found in the r8a7790 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Instantiate the two system DMA controllers in the r8a7794 device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Traditionally, the first 16 MiB of RAM was reserved for the RT
processor.  However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.

As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.

While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Traditionally, the first 16 MiB of RAM was reserved for the RT
processor.  However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.

As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.

While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Specifies clock sources and register bits.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[geert: Drop renesas,src-shift/renesas,src-width, pad to 4 or 8 parents]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable the kzm9g touchscreen controller in the board's DT file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a DT node for the R2025D real-time clock, which is connected to
i2c0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a DT node for the ADXL345 three-axis digital accelerometer sensor,
which is connected to i2c0.

As trivial i2c devices are matched against the first compatible entry
only, compatibility is declared with "adi,adxl34x" only for now.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The device needs an interrupt to operate properly. Specify the two
interrupts used on the board.

While at it rename the DT node to accelerometer@1d to describe the
device's function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a DT node for the AK8975 magnetometer sensor, which is connected to
i2c0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Specify the device interrupt to avoid polling for end of conversion.

While at it rename the DT node to compass@c to describe the device's
function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

While at it rename the ak4648 node to "codec" to describe the device's
function instead of its model, and move its device-specific property
after its generic properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The sh73a0 INTC can't mask interrupts properly most likely due to a
hardware bug. Set the control-parent property to delegate masking to the
parent interrupt controller.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>