Various parts of the HW code are applicable for
both v2.0 and v2.1.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver loads its firmware from files rtlwifi/rtl8723fw*.bin, but the
MODULE_FIRMWARE macros refer to rtlwifi/RTL8723aefw*.bin.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>  [3.8+]
Reported-by: Axel Köllhofer <AxelKoellhofer@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Map BIT 9 in TX DMA DWARD 0 as HW write back option.
We must turn on this option in the last TX descriptor,
this is required for old HW compatability.
This option indicate to HW that WB is required for this descriptor.
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The vring index (MAC queue id) must be set in all TX descriptors
otherwise HW will fail to release descriptors for a specific vring
(disconnect or vring switch flows).
This is normally occurs when fragmentation required, if vring index
will not be the same for all SKB descriptors HW will fail to flush
this MAC queue.
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use common names instead of chip specific ones.
The patch contains no functional changes, but
it makes it easier to add support for further
descriptor sizes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Different chipsets may use different TXWI descriptor
size. Instead of using a hardcoded value, use the
'queue->winfo_size' which holds the correct value for
a given device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The current code uses the same index value both
for the channel information array and for the TX
power table. The index starts from 14, however the
index of the TX power table must start from zero.

Fix it, in order to get the correct TX power value
for a given channel.

The changes in rt61pci.c and rt73usb.c are compile
tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Smatch complains that this is a read past the end of the array.  It
turns out we are printing the wrong array here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since platform support is required for WoW, identify and
and enable Wow only for supported cards.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Most of these relate to endianness problems, and are purely cosmetic.

But a couple of them were legit -- listen interval parsing and some of
the rate selection code would malfunction on BE systems.

There's still one cosmetic warning remaining, in the (admittedly) ugly
code in cw1200_spi.c.  It's there because the hardware needs 16-bit SPI
transfers, but many SPI controllers only operate 8 bits at a time.

If there's a cleaner way of handling this, I'm all ears.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix to return -ENOMEM in the ipw_rx_queue_alloc() error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath_tx_txqaddbuf assumes that all the linked buffers in the queue passed
to it are part of the same A-MPDU or MPDU. The CAB queue rework violates
this assumption, which can cause the internal queue depth to go
negative.
Fix this by increasing the counter for all slots of [bf, bf->bf_lastbf]
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This provides some of the same info found in
the ath9k_htc debugfs through the standard ethtool stats API.

This logic is only supported when ath9k_htc debugfs kernel
feature is enabled, since that is the only time stats
are actually gathered.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Previously the default mesh STA nonpeer power mode was
UNKNOWN (0) make the default mesh STA power mode ACTIVE,
to prevent unnecessary  frame buffering while peering is
not yet complete. Fixes a panic in ath9k_htc when adding
stations from userspace, and mcast buffered frames are
later released.

Thanks to Bob Copeland for his help debugging this.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Useful for userspace mesh to authenticate and peer without
a station entry, since both steps may fail anyway.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The following compilation issue popped up moving from v3.10-rc1 to
v3.10-rc6 after merging wireless-testing.

net/wireless/sysfs.c:86:13: error: 'cfg80211_leave_all' defined
but not used [-Werror=unused-function]

The function is only called when CONFIG_PM is enabled. Moving the
function under CONFIG_PM as well.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If it *is* still set when the netdev is being deleted,
then we are about to leak a pointer.  Warn and clean up
in that case.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Should help the next person that tries to understand
the bss refcounting logic.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Otherwise, we can leak a bss reference.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

After receiving channel switch announcement from AP, scan and
association on that channel is blocked for DFS_CHAN_MOVE_TIME
(10 seconds). Hence station will be able to connect to the AP,
once it is moved to new channel.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds code to parse requested AP's 11h capabilities
and add 11h information in association request.

Also, deauth is sent to the AP after receiving channel switch
announcement event from firmware. This happens when AP advertises
WLAN_EID_CHANNEL_SWITCH IE in it's beacon.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Do not unconditionally access the chan variable in
brcmf_cfg80211_mgmt_tx() as it may be NULL.
Use freq instead.

Introduced by c2ff8cad
("brcm80211: make mgmt_tx in brcmfmac accept a NULL channel")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use negative check (if(!bss_desc)) and return failure
instead of failing a NULL check later in
mwifiex_check_network_compatibility() routine.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the
same condition twice. The problem was found using cppcheck-1.49, and the
proper fix was verified against the pre-mac80211 version of the code.

This patch was originally included as commit 1288aa4e, but was accidentally
reverted in a later patch.

Reported-by: David Binderman <dcb314@hotmail.com> [original report]
Reported-by: Andrea Morello <andrea.merello@gmail.com> [report of accidental reversion]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>  [back to 2.6.39]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes the potential issue that the BSS struct that we use
and later assign to wdev->current_bss is removed from the scan
list while associating.

Also warn when we don't have a BSS struct in connect_result
unless it's from a driver that only has the connect() API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Doing so will allow us to hold the BSS (not just ref it) over the
association process, thus ensuring that it doesn't time out and
gets invisible to the user (e.g. in 'iw wlan0 link'.)

This also fixes a leak in mac80211 where it doesn't always release
the BSS struct properly in all cases where calling this function.
This leak was reported by Ben Greear.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Avoid parsing the original dump message again and again by
allocating a small state struct that is used by the functions
involved in the dump, storing this struct in cb->args[0].
This reduces the memory allocation size as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge mac80211 to avoid conflicts with the nl80211 attrbuf
changes.

Conflicts:
	net/mac80211/iface.c
	net/wireless/nl80211.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since my commit 3713b4e3 ("nl80211: allow splitting wiphy
information in dumps"), nl80211_dump_wiphy() uses the global
nl80211_fam.attrbuf for parsing the incoming data. This wouldn't
be a problem if it only did so on the first dump iteration which
is locked against other commands in generic netlink, but due to
space constraints in cb->args (the needed state doesn't fit) I
decided to always parse the original message. That's racy though
since nl80211_fam.attrbuf could be used by some other parsing in
generic netlink concurrently.

For now, fix this by allocating a separate parse buffer (it's a
bit too big for the stack, currently 1448 bytes on 64-bit). For
-next, I'll change the code to parse into the global buffer in
the first round only and then allocate a smaller buffer to keep
the data in cb->args.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add scatter gather list support for better rx glom performance.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Introducing a new SDIO block data access interface function
brcmf_sdio_buffrw. It will act as a unified interface function for any block
data access to WiFi dongle through SDIO interface. This patch enables
the support for single skb transmission.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is an ID table registered to SDIO stack which consists of all SDIO devices
supported by brcmfmac. It is not necessary to have an extra check.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of allocating an empty list item and queue that for
the dpc data worker to dequeue an atomic counter is used.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Just cleaning up and being consistent in naming operations
related to struct brcmf_fws_mac_descriptor objects.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The firmware-signalling code used NL80211_NUM_ACS, but it has
its own definition enum brcmf_fws_fifo, which is more appropriate
to use. This effectively removes the need to include nl80211.h.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>