In the old code, there was a race condition between the stop endpoint
command and the URB submission process.  When the stop endpoint command is
handled by the event handler, the endpoint ring is assumed to be stopped.
When a stop endpoint command is queued, URB submissions are to not ring
the doorbell.  The old code would check the number of pending URBs to be
canceled, and would not ring the doorbell if it was non-zero.

However, the following race condition could occur with the old code:

1. Cancel an URB, add it to the list of URBs to be canceled, queue the stop
   endpoint command, and increment ep->cancels_pending to 1.
2. The URB finishes on the HW, and an event is enqueued to the event ring
   (at the same time as 1).
3. The stop endpoint command finishes, and the endpoint is halted.  An
   event is queued to the event ring.
4. The event handler sees the finished URB, notices it was to be
   canceled, decrements ep->cancels_pending to 0, and removes it from the to
   be canceled list.
5. The event handler drops the lock and gives back the URB.  The
   completion handler requeues the URB (or a different driver enqueues a new
   URB).  This causes the endpoint's doorbell to be rung, since
   ep->cancels_pending == 0.  The endpoint is now running.
6. A second URB is canceled, and it's added to the canceled list.
   Since ep->cancels_pending == 0, a new stop endpoint command is queued, and
   ep->cancels_pending is incremented to 1.
7. The event handler then sees the completed stop endpoint command.  The
   handler assumes the endpoint is stopped, but it isn't.  It attempts to
   move the dequeue pointer or change TDs to cancel the second URB, while the
   hardware is actively accessing the endpoint ring.

To eliminate this race condition, a new endpoint state bit is introduced,
EP_HALT_PENDING.  When this bit is set, a stop endpoint command has been
queued, and the command handler has not begun to process the URB
cancellation list yet.  The endpoint doorbell should not be rung when this
is set.  Set this when a stop endpoint command is queued, clear it when
the handler for that command runs, and check if it's set before ringing a
doorbell.  ep->cancels_pending is eliminated, because it is no longer
used.

Make sure to ring the doorbell for an endpoint when the stop endpoint
command handler runs, even if the canceled URB list is empty.  All
canceled URBs could have completed and new URBs could have been enqueued
without the doorbell being rung before the command was handled.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb: better error handling in usb_port_suspend

- disable remote wakeup only if it was enabled
- refuse to autosuspend if remote wakeup fails to be enabled
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

this driver has been sitting in linux-omap tree for quite
some time. It adds support for omap's ehci controller.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This adds a minimal generic driver for ULPI connected transceivers,
using the OTG framework functions recently introduced.

The driver got a table to match the ULPI chips, which currently only has
one entry for NXP's ISP 1504 transceiver.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This adds support for OTG transceivers directly connected to the ULPI
interface. In particular, the following details are added

- a struct for low level io functions (read/write)
- a priv field to be used as 'viewport' by low level access functions
- an (*init) and (*shutdown) callbacks, along with static inline helpers
- a (*set_vbus) callback to switch the port power on and off
- a flags field for per-transceiver settings
- some defines for the flags bitmask to configure platform specific
  details
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add the wusb_phy_rate sysfs file to Wireless USB host controllers.  This
sets the maximum PHY rate that will be used for all connected devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Print ep number, direction and type; and current window in asl and pzl
debugfs files.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Modify both host and gadget USB drivers for at91sam9g10.
This add a clock management equivalent to at91sam9261 on usb drivers.
It also add the way of handling gadget pull-ups (like the at91sam9261).
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Now that control requests targeted at an endpoint can be handled at the
function level, move the UAC-specific control request handling code from
the audio gadget driver to the audio function driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Control requests targeted at an endpoint (that is sent to EP0 but
specifying the target endpoint address in wIndex) are dispatched to the
current configuration's setup callback, requiring all gadget drivers to
dispatch the requests to the correct function driver.

To avoid this, record which endpoints are used by each function in the
composite driver SET CONFIGURATION handler and dispatch requests
targeted at endpoints to the correct function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Correct priority problem in the use of ! and &.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@ expression E; constant C; @@
- !E & C
+ !(E & C)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix type and format warning in the new sg code.  Remove the very chatty
debug messages that were left in by mistake and use min_t() as required
(no one seems to agree on a type for buffer sizes).
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Check urb->interval on interrupt transfers and allow those with valid
values (6 <= interval <= 16).
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Support urbs with scatter-gather lists by trying to fit sg list elements
into page lists in one or more qTDs.  qTDs must end on a wMaxPacketSize
boundary so if this isn't possible the urb's sg list must be copied into
bounce buffers.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The WHCI HCD will also support urbs with scatter-gather lists.  Add a
usb_bus field to indicated how many sg list elements are supported by
the HCD.  Use this to decide whether to pass the scatter-list to the HCD
or not.

Make the usb-storage driver use this new field.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I can't see any reason why these would not be static.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add bus glue driver for Xilinx USB host controller. The controller can be
configured as HS only or HS/FS hybrid. The driver uses the device tree file
to configure the driver according to the setting in the hardware system.

This driver has been tested with usbtest using the NET2280 PCI card.
Signed-off-by: Julie Zhu <julie.zhu@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Use dev_dbg() instead of an unconditional printk(KERN_DEBUG).  This has
two benefits; one is that it identifies the USB device which the messages
related to, and the other is that the messages won't be produced unless
debug is turned on.

Enable the debug messages when CONFIG_USB_STORAGE_DEBUG is set.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Instead of reporting "SCSI emulation for USB Mass Storage devices",
report "usb-storage 1-4:1.0".
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Knowing which configuration was chosen is a debugging aid more than it
is informational.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

No need to check ehci->debug twice.

Found-by: Sergei Shtylyov sshtylyov@ru.mvista.com
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add mark and space parity, since the device supports it.
Signed-off-by: Roland Koebler <r.koebler@yahoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: Add debugobjects support

* 'bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
  xen: try harder to balloon up under memory pressure.
  Xen balloon: fix totalram_pages counting.
  xen: explicitly create/destroy stop_machine workqueues outside suspend/resume region.
  xen: improve error handling in do_suspend.
  xen: don't leak IRQs over suspend/resume.
  xen: call clock resume notifier on all CPUs
  xen: use iret for return from 64b kernel to 32b usermode
  xen: don't call dpm_resume_noirq() with interrupts disabled.
  xen: register runstate info for boot CPU early
  xen: register runstate on secondary CPUs
  xen: register timer interrupt with IRQF_TIMER
  xen: correctly restore pfn_to_mfn_list_list after resume
  xen: restore runstate_info even if !have_vcpu_info_placement
  xen: re-register runstate area earlier on resume.
  xen: wait up to 5 minutes for device connetion
  xen: improvement to wait_for_devices()
  xen: fix is_disconnected_device/exists_disconnected_device
  xen/xenbus: make DEVICE_ATTR()s static

* 'xen/fbdev' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
  xen pvfb: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers.
  fb-defio: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers.
  fb-defio: If FBINFO_VIRTFB is defined, do not set VM_IO flag.
  Fix toogle whether xenbus driver should be built as module or part of kernel.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
  dlm: always use GFP_NOFS

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (47 commits)
  ext4: Fix potential fiemap deadlock (mmap_sem vs. i_data_sem)
  ext4: Do not override ext2 or ext3 if built they are built as modules
  jbd2: Export jbd2_log_start_commit to fix ext4 build
  ext4: Fix insufficient checks in EXT4_IOC_MOVE_EXT
  ext4: Wait for proper transaction commit on fsync
  ext4: fix incorrect block reservation on quota transfer.
  ext4: quota macros cleanup
  ext4: ext4_get_reserved_space() must return bytes instead of blocks
  ext4: remove blocks from inode prealloc list on failure
  ext4: wait for log to commit when umounting
  ext4: Avoid data / filesystem corruption when write fails to copy data
  ext4: Use ext4 file system driver for ext2/ext3 file system mounts
  ext4: Return the PTR_ERR of the correct pointer in setup_new_group_blocks()
  jbd2: Add ENOMEM checking in and for jbd2_journal_write_metadata_buffer()
  ext4: remove unused parameter wbc from __ext4_journalled_writepage()
  ext4: remove encountered_congestion trace
  ext4: move_extent_per_page() cleanup
  ext4: initialize moved_len before calling ext4_move_extents()
  ext4: Fix double-free of blocks with EXT4_IOC_MOVE_EXT
  ext4: use ext4_data_block_valid() in ext4_free_blocks()
  ...

* 'for-linus' of git://git.open-osd.org/linux-open-osd:
  exofs: Multi-device mirror support
  exofs: Move all operations to an io_engine
  exofs: move osd.c to ios.c
  exofs: statfs blocks is sectors not FS blocks
  exofs: Prints on mount and unmout
  exofs: refactor exofs_i_info initialization into common helper
  exofs: dbg-print less
  exofs: More sane debug print
  trivial: some small fixes in exofs documentation

* git://git.infradead.org/ubifs-2.6:
  UBIFS: fix return code in check_leaf
  UBI: flush wl before clearing update marker
  MAINTAINERS: change e-mail of Artem Bityutskiy
  UBIFS: remove manual O_SYNC handling
  UBIFS: support mounting of UBI volume character devices
  UBI: Add ubi_open_volume_path

This patch drops usage of floating point variable for 32bit build
Signed-off-by: David T. L. Wong <davidtlwong@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This patch changes on-disk format, it is accompanied with a parallel
patch to mkfs.exofs that enables multi-device capabilities.

After this patch, old exofs will refuse to mount a new formatted FS and
new exofs will refuse an old format. This is done by moving the magic
field offset inside the FSCB. A new FSCB *version* field was added. In
the future, exofs will refuse to mount unmatched FSCB version. To
up-grade or down-grade an exofs one must use mkfs.exofs --upgrade option
before mounting.

Introduced, a new object that contains a *device-table*. This object
contains the default *data-map* and a linear array of devices
information, which identifies the devices used in the filesystem. This
object is only written to offline by mkfs.exofs. This is why it is kept
separate from the FSCB, since the later is written to while mounted.

Same partition number, same object number is used on all devices only
the device varies.

* define the new format, then load the device table on mount time make
  sure every thing is supported.

* Change I/O engine to now support Mirror IO, .i.e write same data
  to multiple devices, read from a random device to spread the
  read-load from multiple clients (TODO: stripe read)

Implementation notes:
 A few points introduced in previous patch should be mentioned here:

* Special care was made so absolutlly all operation that have any chance
  of failing are done before any osd-request is executed. This is to
  minimize the need for a data consistency recovery, to only real IO
  errors.

* Each IO state has a kref. It starts at 1, any osd-request executed
  will increment the kref, finally when all are executed the first ref
  is dropped. At IO-done, each request completion decrements the kref,
  the last one to return executes the internal _last_io() routine.
  _last_io() will call the registered io_state_done. On sync mode a
  caller does not supply a done method, indicating a synchronous
  request, the caller is put to sleep and a special io_state_done is
  registered that will awaken the caller. Though also in sync mode all
  operations are executed in parallel.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

In anticipation for multi-device operations, we separate osd operations
into an abstract I/O API. Currently only one device is used but later
when adding more devices, we will drive all devices in parallel according
to a "data_map" that describes how data is arranged on multiple devices.
The file system level operates, like before, as if there is one object
(inode-number) and an i_size. The io engine will split this to the same
object-number but on multiple device.

At first we introduce Mirror (raid 1) layout. But at the final outcome
we intend to fully implement the pNFS-Objects data-map, including
raid 0,4,5,6 over mirrored devices, over multiple device-groups. And
more. See: http://tools.ietf.org/html/draft-ietf-nfsv4-pnfs-obj-12

* Define an io_state based API for accessing osd storage devices
  in an abstract way.
  Usage:
	First a caller allocates an io state with:
		exofs_get_io_state(struct exofs_sb_info *sbi,
				   struct exofs_io_state** ios);

	Then calles one of:
		exofs_sbi_create(struct exofs_io_state *ios);
		exofs_sbi_remove(struct exofs_io_state *ios);
		exofs_sbi_write(struct exofs_io_state *ios);
		exofs_sbi_read(struct exofs_io_state *ios);
		exofs_oi_truncate(struct exofs_i_info *oi, u64 new_len);

	And when done
		exofs_put_io_state(struct exofs_io_state *ios);

* Convert all source files to use this new API
* Convert from bio_alloc to bio_kmalloc
* In io engine we make use of the now fixed osd_req_decode_sense

There are no functional changes or on disk additions after this patch.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

If I do a "git mv" together with a massive code change
and commit in one patch, git looses the rename and
records a delete/new instead. This is bad because I want
a rename recorded so later rebased/cherry-picked patches
to the old name will work. Also the --follow is lost.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

Even though exofs has a 4k block size, statfs blocks
is in sectors (512 bytes).

Also if target returns 0 for capacity then make it
ULLONG_MAX. df does not like zero-size filesystems
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

It is important to print in the logs when a filesystem was
mounted and eventually unmounted.

Print the osd-device's osd_name and pid the FS was
mounted/unmounted on.

TODO: How to also print the namespace path the filesystem was
      mounted on?
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

There are two places that initialize inodes: exofs_iget() and
exofs_new_inode()

As more members of exofs_i_info that need initialization are
added this code will grow. (soon)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

Iner-loops printing is converted to EXOFS_DBG2 which is #defined
to nothing.

It is now almost bareable to just leave debug-on. Every operation
is printed once, with most relevant info (I hope).
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

debug prints should be somewhat useful without actually
reading the source code
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

Add exofs.txt to filesystems Documentation index and fix some typos,
identation and grammar.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>