- 10 Feb, 2017 40 commits
-
-
Paolo Abeni authored
commit b5c2d495 upstream. If an ip6 tunnel is configured to inherit the traffic class from the inner header, the dst_cache must be disabled or it will foul the policy routing. The issue is apprently there since at leat Linux-2.6.12-rc2. Reported-by:
Liam McBirnie <liam.mcbirnie@boeing.com> Cc: Liam McBirnie <liam.mcbirnie@boeing.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Willy Tarreau <w@1wt.eu>
-
Eli Cooper authored
commit 23f4ffed upstream. skb->cb may contain data from previous layers. In the observed scenario, the garbage data were misinterpreted as IP6CB(skb)->frag_max_size, so that small packets sent through the tunnel are mistakenly fragmented. This patch unconditionally clears the control buffer in ip6tunnel_xmit(), which affects ip6_tunnel, ip6_udp_tunnel and ip6_gre. Currently none of these tunnels set IP6CB(skb)->flags, otherwise it needs to be done earlier. Cc: stable@vger.kernel.org Signed-off-by:
Eli Cooper <elicooper@gmx.com> Signed-off-by:
-
Eric Dumazet authored
commit 990ff4d8 upstream. While fuzzing kernel with syzkaller, Andrey reported a nasty crash in inet6_bind() caused by DCCP lacking a required method. Fixes: ab1e0a13 ("[SOCK] proto: Add hashinfo member to struct proto") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Andrey Konovalov <andreyknvl@google.com> Tested-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Eric Dumazet authored
commit 1aa9d1a0 upstream. dccp_v6_err() does not use pskb_may_pull() and might access garbage. We only need 4 bytes at the beginning of the DCCP header, like TCP, so the 8 bytes pulled in icmpv6_notify() are more than enough. Signed-off-by:
-
Nicolas Dichtel authored
commit a220445f upstream. The goal of the patch is to fix this scenario: ip link add dummy1 type dummy ip link set dummy1 up ip link set lo down ; ip link set lo up After that sequence, the local route to the link layer address of dummy1 is not there anymore. When the loopback is set down, all local routes are deleted by addrconf_ifdown()/rt6_ifdown(). At this time, the rt6_info entry still exists, because the corresponding idev has a reference on it. After the rcu grace period, dst_rcu_free() is called, and thus ___dst_free(), which will set obsolete to DST_OBSOLETE_DEAD. In this case, init_loopback() is called before dst_rcu_free(), thus obsolete is still sets to something <= 0. So, the function doesn't add the route again. To avoid that race, let's check the rt6 refcnt instead. Fixes: 25fb6ca4 ("net IPv6 : Fix broken IPv6 routing table after loopback down-up") Fixes: a881ae1f ("ipv6: don't call addrconf_dst_alloc again when enable lo") Fixes: 33d99113 ("ipv6: reallocate addrconf router for ipv6 address when lo device up") Reported-by:
Francesco Santoro <francesco.santoro@6wind.com> Reported-by:
Samuel Gauthier <samuel.gauthier@6wind.com> CC: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com> CC: Maruthi Thotad <Maruthi.Thotad@ap.sony.com> CC: Sabrina Dubroca <sd@queasysnail.net> CC: Hannes Frederic Sowa <hannes@stressinduktion.org> CC: Weilong Chen <chenweilong@huawei.com> CC: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Lance Richardson authored
commit db32e4e4 upstream. Similar to commit 3be07244 ("ip6_gre: fix flowi6_proto value in xmit path"), set flowi6_proto to IPPROTO_GRE for output route lookup. Up until now, ip6gre_xmit_other() has set flowi6_proto to a bogus value. This affected output route lookup for packets sent on an ip6gretap device in cases where routing was dependent on the value of flowi6_proto. Since the correct proto is already set in the tunnel flowi6 template via commit 252f3f5a ("ip6_gre: Set flowi6_proto as IPPROTO_GRE in xmit path."), simply delete the line setting the incorrect flowi6_proto value. Suggested-by:
Jiri Benc <jbenc@redhat.com> Fixes: c12b395a ("gre: Support GRE over IPv6") Reviewed-by:
Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by:
Lance Richardson <lrichard@redhat.com> Signed-off-by:
-
Sabrina Dubroca authored
commit a9ed4a29 upstream. Calling setsockopt with IPV6_JOIN_ANYCAST or IPV6_LEAVE_ANYCAST triggers the assertion in addrconf_join_solict()/addrconf_leave_solict() ipv6_sock_ac_join(), ipv6_sock_ac_drop(), ipv6_sock_ac_close() need to take RTNL before calling ipv6_dev_ac_inc/dec. Same thing with ipv6_sock_mc_join(), ipv6_sock_mc_drop(), ipv6_sock_mc_close() before calling ipv6_dev_mc_inc/dec. This patch moves ASSERT_RTNL() up a level in the call stack. Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Reported-by:
Tommi Rantala <tt.rantala@gmail.com> Acked-by:
Mike Manning <mmanning@brocade.com> Signed-off-by:
-
Wei Yongjun authored
commit 751eb6b6 upstream. In general, when DAD detected IPv6 duplicate address, ifp->state will be set to INET6_IFADDR_STATE_ERRDAD and DAD is stopped by a delayed work, the call tree should be like this: ndisc_recv_ns -> addrconf_dad_failure <- missing ifp put -> addrconf_mod_dad_work -> schedule addrconf_dad_work() -> addrconf_dad_stop() <- missing ifp hold before call it addrconf_dad_failure() called with ifp refcont holding but not put. addrconf_dad_work() call addrconf_dad_stop() without extra holding refcount. This will not cause any issue normally. But the race between addrconf_dad_failure() and addrconf_dad_work() may cause ifp refcount leak and netdevice can not be unregister, dmesg show the following messages: IPv6: eth0: IPv6 duplicate address fe80::XX:XXXX:XXXX:XX detected! ... unregister_netdevice: waiting for eth0 to become free. Usage count = 1 Cc: stable@vger.kernel.org Fixes: c15b1cca ("ipv6: move DAD and addrconf_verify processing to workqueue") Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
Hannes Frederic Sowa authored
commit c15b1cca upstream. addrconf_join_solict and addrconf_join_anycast may cause actions which need rtnl locked, especially on first address creation. A new DAD state is introduced which defers processing of the initial DAD processing into a workqueue. To get rtnl lock we need to push the code paths which depend on those calls up to workqueues, specifically addrconf_verify and the DAD processing. (v2) addrconf_dad_failure needs to be queued up to the workqueue, too. This patch introduces a new DAD state and stop the DAD processing in the workqueue (this is because of the possible ipv6_del_addr processing which removes the solicited multicast address from the device). addrconf_verify_lock is removed, too. After the transition it is not needed any more. As we are not processing in bottom half anymore we need to be a bit more careful about disabling bottom half out when we lock spin_locks which are also used in bh. Relevant backtrace: [ 541.030090] RTNL: assertion failed at net/core/dev.c (4496) [ 541.031143] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 3.10.33-1-amd64-vyatta #1 [ 541.031145] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007 [ 541.031146] ffffffff8148a9f0 000000000000002f ffffffff813c98c1 ffff88007c4451f8 [ 541.031148] 0000000000000000 0000000000000000 ffffffff813d3540 ffff88007fc03d18 [ 541.031150] 0000880000000006 ffff88007c445000 ffffffffa0194160 0000000000000000 [ 541.031152] Call Trace: [ 541.031153] <IRQ> [<ffffffff8148a9f0>] ? dump_stack+0xd/0x17 [ 541.031180] [<ffffffff813c98c1>] ? __dev_set_promiscuity+0x101/0x180 [ 541.031183] [<ffffffff813d3540>] ? __hw_addr_create_ex+0x60/0xc0 [ 541.031185] [<ffffffff813cfe1a>] ? __dev_set_rx_mode+0xaa/0xc0 [ 541.031189] [<ffffffff813d3a81>] ? __dev_mc_add+0x61/0x90 [ 541.031198] [<ffffffffa01dcf9c>] ? igmp6_group_added+0xfc/0x1a0 [ipv6] [ 541.031208] [<ffffffff8111237b>] ? kmem_cache_alloc+0xcb/0xd0 [ 541.031212] [<ffffffffa01ddcd7>] ? ipv6_dev_mc_inc+0x267/0x300 [ipv6] [ 541.031216] [<ffffffffa01c2fae>] ? addrconf_join_solict+0x2e/0x40 [ipv6] [ 541.031219] [<ffffffffa01ba2e9>] ? ipv6_dev_ac_inc+0x159/0x1f0 [ipv6] [ 541.031223] [<ffffffffa01c0772>] ? addrconf_join_anycast+0x92/0xa0 [ipv6] [ 541.031226] [<ffffffffa01c311e>] ? __ipv6_ifa_notify+0x11e/0x1e0 [ipv6] [ 541.031229] [<ffffffffa01c3213>] ? ipv6_ifa_notify+0x33/0x50 [ipv6] [ 541.031233] [<ffffffffa01c36c8>] ? addrconf_dad_completed+0x28/0x100 [ipv6] [ 541.031241] [<ffffffff81075c1d>] ? task_cputime+0x2d/0x50 [ 541.031244] [<ffffffffa01c38d6>] ? addrconf_dad_timer+0x136/0x150 [ipv6] [ 541.031247] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6] [ 541.031255] [<ffffffff8105313a>] ? call_timer_fn.isra.22+0x2a/0x90 [ 541.031258] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6] Hunks and backtrace stolen from a patch by Stephen Hemminger. Reported-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
Hannes Frederic Sowa authored
commit b7b1bfce upstream. This patch splits the timers for duplicate address detection and router solicitations apart. The router solicitations timer goes into inet6_dev and the dad timer stays in inet6_ifaddr. The reason behind this patch is to reduce the number of unneeded router solicitations send out by the host if additional link-local addresses are created. Currently we send out RS for every link-local address on an interface. If the RS timer fires we pick a source address with ipv6_get_lladdr. This change could hurt people adding additional link-local addresses and specifying these addresses in the radvd clients section because we no longer guarantee that we use every ll address as source address in router solicitations. Cc: Flavio Leitner <fleitner@redhat.com> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: David Stevens <dlstevens@us.ibm.com> Signed-off-by:
Flavio Leitner <fbl@redhat.com> Signed-off-by:
-
Michal Kube�ek authored
commit 2c861cc6 upstream. When loading the ipv6 module, ndisc_init() is called before ip6_route_init(). As the former registers a handler calling fib6_run_gc(), this opens a window to run the garbage collector before necessary data structures are initialized. If a network device is initialized in this window, adding MAC address to it triggers a NETDEV_CHANGEADDR event, leading to a crash in fib6_clean_all(). Take the event handler registration out of ndisc_init() into a separate function ndisc_late_init() and move it after ip6_route_init(). Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
-
Joe Perches authored
commit 8c7fbe57 upstream. Commit 38764884 ("include/stddef.h: Move offsetofend() from vfio.h to a generic kernel header") added offsetofend outside the normal include #ifndef/#endif guard. Move it inside. Miscellanea: o remove unnecessary blank line o standardize offsetof macros whitespace style Signed-off-by:
Joe Perches <joe@perches.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [wt: backported only for ipv6 out-of-bounds fix] Signed-off-by:
-
Denys Vlasenko authored
commit 38764884 upstream. Suggested by Andy. Suggested-by:
Andy Lutomirski <luto@amacapital.net> Signed-off-by:
Denys Vlasenko <dvlasenk@redhat.com> Acked-by:
Ingo Molnar <mingo@kernel.org> [wt: backported only for ipv6 out-of-bounds fix] Signed-off-by:
-
Gavin Shan authored
commit b13460b9 upstream. The macro offsetofend() introduces unnecessary temporary variable "tmp". The patch avoids that and saves a bit memory in stack. Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> [wt: backported only for ipv6 out-of-bounds fix] Signed-off-by:
-
Scot Doyle authored
commit 009e39ae upstream. When resizing a vt its selection may exceed the new size, resulting in an invalid memory access [1]. Clear the selection before resizing. [1] http://lkml.kernel.org/r/CACT4Y+acDTwy4umEvf5ROBGiRJNrxHN4Cn5szCXE5Jw-d1B=Xw@mail.gmail.comReported-and-tested-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Scot Doyle <lkml14@scotdoyle.com> Signed-off-by:
-
Jiri Slaby authored
commit 42acfc66 upstream. In csi_J(3), the third parameter of scr_memsetw (vc_screenbuf_size) is divided by 2 inappropriatelly. But scr_memsetw expects size, not count, because it divides the size by 2 on its own before doing actual memset-by-words. So remove the bogus division. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: Petr PÃsaÅ <ppisar@redhat.com> Fixes: f8df13e0 (tty: Clean console safely) Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Dmitry Vyukov authored
commit 32b2921e upstream. Size of kmalloc() in vc_do_resize() is controlled by user. Too large kmalloc() size triggers WARNING message on console. Put a reasonable upper bound on terminal size to prevent WARNINGs. Signed-off-by:
-
Peter Hurley authored
commit dd42bf11 upstream. Line discipline drivers may mistakenly misuse ldisc-related fields when initializing. For example, a failure to initialize tty->receive_room in the N_GIGASET_M101 line discipline was recently found and fixed [1]. Now, the N_X25 line discipline has been discovered accessing the previous line discipline's already-freed private data [2]. Harden the ldisc interface against misuse by initializing revelant tty fields before instancing the new line discipline. [1] commit fd98e941 Author: Tilman Schmidt <tilman@imap.cc> Date: Tue Jul 14 00:37:13 2015 +0200 isdn/gigaset: reset tty->receive_room when attaching ser_gigaset [2] Report from Sasha Levin <sasha.levin@oracle.com> [ 634.336761] ================================================================== [ 634.338226] BUG: KASAN: use-after-free in x25_asy_open_tty+0x13d/0x490 at addr ffff8800a743efd0 [ 634.339558] Read of size 4 by task syzkaller_execu/8981 [ 634.340359] ============================================================================= [ 634.341598] BUG kmalloc-512 (Not tainted): kasan: bad access detected ... [ 634.405018] Call Trace: [ 634.405277] dump_stack (lib/dump_stack.c:52) [ 634.405775] print_trailer (mm/slub.c:655) [ 634.406361] object_err (mm/slub.c:662) [ 634.406824] kasan_report_error (mm/kasan/report.c:138 mm/kasan/report.c:236) [ 634.409581] __asan_report_load4_noabort (mm/kasan/report.c:279) [ 634.411355] x25_asy_open_tty (drivers/net/wan/x25_asy.c:559 (discriminator 1)) [ 634.413997] tty_ldisc_open.isra.2 (drivers/tty/tty_ldisc.c:447) [ 634.414549] tty_set_ldisc (drivers/tty/tty_ldisc.c:567) [ 634.415057] tty_ioctl (drivers/tty/tty_io.c:2646 drivers/tty/tty_io.c:2879) [ 634.423524] do_vfs_ioctl (fs/ioctl.c:43 fs/ioctl.c:607) [ 634.427491] SyS_ioctl (fs/ioctl.c:622 fs/ioctl.c:613) [ 634.427945] entry_SYSCALL_64_fastpath (arch/x86/entry/entry_64.S:188) Cc: Tilman Schmidt <tilman@imap.cc> Cc: Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Peter Zijlstra authored
commit c3c87e77 upstream. The fix from 9fc81d87 ("perf: Fix events installation during moving group") was incomplete in that it failed to recognise that creating a group with events for different CPUs is semantically broken -- they cannot be co-scheduled. Furthermore, it leads to real breakage where, when we create an event for CPU Y and then migrate it to form a group on CPU X, the code gets confused where the counter is programmed -- triggered in practice as well by me via the perf fuzzer. Fix this by tightening the rules for creating groups. Only allow grouping of counters that can be co-scheduled in the same context. This means for the same task and/or the same cpu. Fixes: 9fc81d87 ("perf: Fix events installation during moving group") Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/20150123125834.090683288@infradead.orgSigned-off-by:
-
Arnaldo Carvalho de Melo authored
commit 432746f8 upstream. When we call symbol__fixup_duplicate() we use algorithms to pick the "best" symbols for cases where there are various functions/aliases to an address, and those check zero size symbols, which, before calling symbol__fixup_end() are _all_ symbols in a just parsed kallsyms file. So first fixup the end, then fixup the duplicates. Found while trying to figure out why 'perf test vmlinux' failed, see the output of 'perf test -v vmlinux' to see cases where the symbols picked as best for vmlinux don't match the ones picked for kallsyms. Cc: Anton Blanchard <anton@samba.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Fixes: 694bf407 ("perf symbols: Add some heuristics for choosing the best duplicate symbol") Link: http://lkml.kernel.org/n/tip-rxqvdgr0mqjdxee0kf8i2ufn@git.kernel.orgSigned-off-by:
-
Karl Beldan authored
commit f6d7c1b5 upstream. This fixes subpage writes when using 4-bit HW ECC. There has been numerous reports about ECC errors with devices using this driver for a while. Also the 4-bit ECC has been reported as broken with subpages in [1] and with 16 bits NANDs in the driver and in mach* board files both in mainline and in the vendor BSPs. What I saw with 4-bit ECC on a 16bits NAND (on an LCDK) which got me to try reinitializing the ECC engine: - R/W on whole pages properly generates/checks RS code - try writing the 1st subpage only of a blank page, the subpage is well written and the RS code properly generated, re-reading the same page the HW detects some ECC error, reading the same page again no ECC error is detected Note that the ECC engine is already reinitialized in the 1-bit case. Tested on my LCDK with UBI+UBIFS using subpages. This could potentially get rid of the issue workarounded in [1]. [1] 28c015a9 ("mtd: davinci-nand: disable subpage write for keystone-nand") Fixes: 6a4123e5 ("mtd: nand: davinci_nand, 4-bit ECC for smallpage") Signed-off-by:
Karl Beldan <kbeldan@baylibre.com> Acked-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Dan Carpenter authored
commit 79ad07d4 upstream. There is a cut and paste issue here. The bug is that we are allocating more memory than necessary for msp_maps. We should be allocating enough space for a map_info struct (144 bytes) but we instead allocate enough for an mtd_info struct (1840 bytes). It's a small waste. The other part of this is not harmful but when we allocated msp_flash then we allocated enough space fro a map_info pointer instead of an mtd_info pointer. But since pointers are the same size it works out fine. Anyway, I decided to clean up all three allocations a bit to make them a bit more consistent and clear. Fixes: 68aa0fa8 ('[MTD] PMC MSP71xx flash/rootfs mappings') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Brian Norris authored
commit f3c63795 upstream. Commit 073db4a5 ("mtd: fix: avoid race condition when accessing mtd->usecount") fixed a race condition but due to poor ordering of the mutex acquisition, introduced a potential deadlock. The deadlock can occur, for example, when rmmod'ing the m25p80 module, which will delete one or more MTDs, along with any corresponding mtdblock devices. This could potentially race with an acquisition of the block device as follows. -> blktrans_open() -> mutex_lock(&dev->lock); -> mutex_lock(&mtd_table_mutex); -> del_mtd_device() -> mutex_lock(&mtd_table_mutex); -> blktrans_notify_remove() -> del_mtd_blktrans_dev() -> mutex_lock(&dev->lock); This is a classic (potential) ABBA deadlock, which can be fixed by making the A->B ordering consistent everywhere. There was no real purpose to the ordering in the original patch, AFAIR, so this shouldn't be a problem. This ordering was actually already present in del_mtd_blktrans_dev(), for one, where the function tried to ensure that its caller already held mtd_table_mutex before it acquired &dev->lock: if (mutex_trylock(&mtd_table_mutex)) { mutex_unlock(&mtd_table_mutex); BUG(); } So, reverse the ordering of acquisition of &dev->lock and &mtd_table_mutex so we always acquire mtd_table_mutex first. Snippets of the lockdep output follow: # modprobe -r m25p80 [ 53.419251] [ 53.420838] ====================================================== [ 53.427300] [ INFO: possible circular locking dependency detected ] [ 53.433865] 4.3.0-rc6 #96 Not tainted [ 53.437686] ------------------------------------------------------- [ 53.444220] modprobe/372 is trying to acquire lock: [ 53.449320] (&new->lock){+.+...}, at: [<c043fe4c>] del_mtd_blktrans_dev+0x80/0xdc [ 53.457271] [ 53.457271] but task is already holding lock: [ 53.463372] (mtd_table_mutex){+.+.+.}, at: [<c0439994>] del_mtd_device+0x18/0x100 [ 53.471321] [ 53.471321] which lock already depends on the new lock. [ 53.471321] [ 53.479856] [ 53.479856] the existing dependency chain (in reverse order) is: [ 53.487660] -> #1 (mtd_table_mutex){+.+.+.}: [ 53.492331] [<c043fc5c>] blktrans_open+0x34/0x1a4 [ 53.497879] [<c01afce0>] __blkdev_get+0xc4/0x3b0 [ 53.503364] [<c01b0bb8>] blkdev_get+0x108/0x320 [ 53.508743] [<c01713c0>] do_dentry_open+0x218/0x314 [ 53.514496] [<c0180454>] path_openat+0x4c0/0xf9c [ 53.519959] [<c0182044>] do_filp_open+0x5c/0xc0 [ 53.525336] [<c0172758>] do_sys_open+0xfc/0x1cc [ 53.530716] [<c000f740>] ret_fast_syscall+0x0/0x1c [ 53.536375] -> #0 (&new->lock){+.+...}: [ 53.540587] [<c063f124>] mutex_lock_nested+0x38/0x3cc [ 53.546504] [<c043fe4c>] del_mtd_blktrans_dev+0x80/0xdc [ 53.552606] [<c043f164>] blktrans_notify_remove+0x7c/0x84 [ 53.558891] [<c04399f0>] del_mtd_device+0x74/0x100 [ 53.564544] [<c043c670>] del_mtd_partitions+0x80/0xc8 [ 53.570451] [<c0439aa0>] mtd_device_unregister+0x24/0x48 [ 53.576637] [<c046ce6c>] spi_drv_remove+0x1c/0x34 [ 53.582207] [<c03de0f0>] __device_release_driver+0x88/0x114 [ 53.588663] [<c03de19c>] device_release_driver+0x20/0x2c [ 53.594843] [<c03dd9e8>] bus_remove_device+0xd8/0x108 [ 53.600748] [<c03dacc0>] device_del+0x10c/0x210 [ 53.606127] [<c03dadd0>] device_unregister+0xc/0x20 [ 53.611849] [<c046d878>] __unregister+0x10/0x20 [ 53.617211] [<c03da868>] device_for_each_child+0x50/0x7c [ 53.623387] [<c046eae8>] spi_unregister_master+0x58/0x8c [ 53.629578] [<c03e12f0>] release_nodes+0x15c/0x1c8 [ 53.635223] [<c03de0f8>] __device_release_driver+0x90/0x114 [ 53.641689] [<c03de900>] driver_detach+0xb4/0xb8 [ 53.647147] [<c03ddc78>] bus_remove_driver+0x4c/0xa0 [ 53.652970] [<c00cab50>] SyS_delete_module+0x11c/0x1e4 [ 53.658976] [<c000f740>] ret_fast_syscall+0x0/0x1c [ 53.664621] [ 53.664621] other info that might help us debug this: [ 53.664621] [ 53.672979] Possible unsafe locking scenario: [ 53.672979] [ 53.679169] CPU0 CPU1 [ 53.683900] ---- ---- [ 53.688633] lock(mtd_table_mutex); [ 53.692383] lock(&new->lock); [ 53.698306] lock(mtd_table_mutex); [ 53.704658] lock(&new->lock); [ 53.707946] [ 53.707946] *** DEADLOCK *** Fixes: 073db4a5 ("mtd: fix: avoid race condition when accessing mtd->usecount") Reported-by:
Felipe Balbi <balbi@ti.com> Tested-by:
-
Mark Bloch authored
commit 9db0ff53 upstream. When there is a CM id object that has port assigned to it, it means that the cm-id asked for the specific port that it should go by it, but if that port was removed (hot-unplug event) the cm-id was not updated. In order to fix that the port keeps a list of all the cm-id's that are planning to go by it, whenever the port is removed it marks all of them as invalid. This commit fixes a kernel panic which happens when running traffic between guests and we force reboot a guest mid traffic, it triggers a kernel panic: Call Trace: [<ffffffff815271fa>] ? panic+0xa7/0x16f [<ffffffff8152b534>] ? oops_end+0xe4/0x100 [<ffffffff8104a00b>] ? no_context+0xfb/0x260 [<ffffffff81084db2>] ? del_timer_sync+0x22/0x30 [<ffffffff8104a295>] ? __bad_area_nosemaphore+0x125/0x1e0 [<ffffffff81084240>] ? process_timeout+0x0/0x10 [<ffffffff8104a363>] ? bad_area_nosemaphore+0x13/0x20 [<ffffffff8104aabf>] ? __do_page_fault+0x31f/0x480 [<ffffffff81065df0>] ? default_wake_function+0x0/0x20 [<ffffffffa0752675>] ? free_msg+0x55/0x70 [mlx5_core] [<ffffffffa0753434>] ? cmd_exec+0x124/0x840 [mlx5_core] [<ffffffff8105a924>] ? find_busiest_group+0x244/0x9f0 [<ffffffff8152d45e>] ? do_page_fault+0x3e/0xa0 [<ffffffff8152a815>] ? page_fault+0x25/0x30 [<ffffffffa024da25>] ? cm_alloc_msg+0x35/0xc0 [ib_cm] [<ffffffffa024e821>] ? ib_send_cm_dreq+0xb1/0x1e0 [ib_cm] [<ffffffffa024f836>] ? cm_destroy_id+0x176/0x320 [ib_cm] [<ffffffffa024fb00>] ? ib_destroy_cm_id+0x10/0x20 [ib_cm] [<ffffffffa034f527>] ? ipoib_cm_free_rx_reap_list+0xa7/0x110 [ib_ipoib] [<ffffffffa034f590>] ? ipoib_cm_rx_reap+0x0/0x20 [ib_ipoib] [<ffffffffa034f5a5>] ? ipoib_cm_rx_reap+0x15/0x20 [ib_ipoib] [<ffffffff81094d20>] ? worker_thread+0x170/0x2a0 [<ffffffff8109b2a0>] ? autoremove_wake_function+0x0/0x40 [<ffffffff81094bb0>] ? worker_thread+0x0/0x2a0 [<ffffffff8109aef6>] ? kthread+0x96/0xa0 [<ffffffff8100c20a>] ? child_rip+0xa/0x20 [<ffffffff8109ae60>] ? kthread+0x0/0xa0 [<ffffffff8100c200>] ? child_rip+0x0/0x20 Fixes: a977049d ("[PATCH] IB: Add the kernel CM implementation") Signed-off-by:
Mark Bloch <markb@mellanox.com> Signed-off-by:
Erez Shitrit <erezsh@mellanox.com> Reviewed-by:
Maor Gottlieb <maorg@mellanox.com> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Tariq Toukan authored
commit 5b810a24 upstream. The real QP is destroyed in case of the ref count reaches zero, but for XRC target QPs this call was missed and caused to QP leaks. Let's call to destroy for all flows. Fixes: 0e0ec7e0 ('RDMA/core: Export ib_open_qp() to share XRC...') Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
Noa Osherovich <noaos@mellanox.com> Signed-off-by:
-
Matan Barak authored
commit 593ff73b upstream. Currently, if ib_copy_to_udata fails, the CQ won't be deleted from the radix tree and the HW (HW2SW). Fixes: 225c7b1f ('IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters') Signed-off-by:
Matan Barak <matanb@mellanox.com> Signed-off-by:
Daniel Jurgens <danielj@mellanox.com> Reviewed-by:
-
Alex Vesker authored
commit e5ac40cd upstream. Because of an incorrect bit-masking done on the join state bits, when handling a join request we failed to detect a difference between the group join state and the request join state when joining as send only full member (0x8). This caused the MC join request not to be sent. This issue is relevant only when SRIOV is enabled and SM supports send only full member. This fix separates scope bits and join states bits a nibble each. Fixes: b9c5d6a6 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV') Signed-off-by:
Alex Vesker <valex@mellanox.com> Signed-off-by:
-
Alex Vesker authored
commit 344bacca upstream. This fix solves a race between light flush and on the fly joins. Light flush doesn't set the device to down and unset IPOIB_OPER_UP flag, this means that if while flushing we have a MC join in progress and the QP was attached to BC MGID we can have a mismatches when re-attaching a QP to the BC MGID. The light flush would set the broadcast group to NULL causing an on the fly join to rejoin and reattach to the BC MCG as well as adding the BC MGID to the multicast list. The flush process would later on remove the BC MGID and detach it from the QP. On the next flush the BC MGID is present in the multicast list but not found when trying to detach it because of the previous double attach and single detach. [18332.714265] ------------[ cut here ]------------ [18332.717775] WARNING: CPU: 6 PID: 3767 at drivers/infiniband/core/verbs.c:280 ib_dealloc_pd+0xff/0x120 [ib_core] ... [18332.775198] Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011 [18332.779411] 0000000000000000 ffff8800b50dfbb0 ffffffff813fed47 0000000000000000 [18332.784960] 0000000000000000 ffff8800b50dfbf0 ffffffff8109add1 0000011832f58300 [18332.790547] ffff880226a596c0 ffff880032482000 ffff880032482830 ffff880226a59280 [18332.796199] Call Trace: [18332.798015] [<ffffffff813fed47>] dump_stack+0x63/0x8c [18332.801831] [<ffffffff8109add1>] __warn+0xd1/0xf0 [18332.805403] [<ffffffff8109aebd>] warn_slowpath_null+0x1d/0x20 [18332.809706] [<ffffffffa025d90f>] ib_dealloc_pd+0xff/0x120 [ib_core] [18332.814384] [<ffffffffa04f3d7c>] ipoib_transport_dev_cleanup+0xfc/0x1d0 [ib_ipoib] [18332.820031] [<ffffffffa04ed648>] ipoib_ib_dev_cleanup+0x98/0x110 [ib_ipoib] [18332.825220] [<ffffffffa04e62c8>] ipoib_dev_cleanup+0x2d8/0x550 [ib_ipoib] [18332.830290] [<ffffffffa04e656f>] ipoib_uninit+0x2f/0x40 [ib_ipoib] [18332.834911] [<ffffffff81772a8a>] rollback_registered_many+0x1aa/0x2c0 [18332.839741] [<ffffffff81772bd1>] rollback_registered+0x31/0x40 [18332.844091] [<ffffffff81773b18>] unregister_netdevice_queue+0x48/0x80 [18332.848880] [<ffffffffa04f489b>] ipoib_vlan_delete+0x1fb/0x290 [ib_ipoib] [18332.853848] [<ffffffffa04df1cd>] delete_child+0x7d/0xf0 [ib_ipoib] [18332.858474] [<ffffffff81520c08>] dev_attr_store+0x18/0x30 [18332.862510] [<ffffffff8127fe4a>] sysfs_kf_write+0x3a/0x50 [18332.866349] [<ffffffff8127f4e0>] kernfs_fop_write+0x120/0x170 [18332.870471] [<ffffffff81207198>] __vfs_write+0x28/0xe0 [18332.874152] [<ffffffff810e09bf>] ? percpu_down_read+0x1f/0x50 [18332.878274] [<ffffffff81208062>] vfs_write+0xa2/0x1a0 [18332.881896] [<ffffffff812093a6>] SyS_write+0x46/0xa0 [18332.885632] [<ffffffff810039b7>] do_syscall_64+0x57/0xb0 [18332.889709] [<ffffffff81883321>] entry_SYSCALL64_slow_path+0x25/0x25 [18332.894727] ---[ end trace 09ebbe31f831ef17 ]--- Fixes: ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM change events") Signed-off-by:
-
Erez Shitrit authored
commit 68c6bcdd upstream. The function send_leave sets the member: group->query_id (group->query_id = ret) after calling the sa_query, but leave_handler can be executed before the setting and it might delete the group object, and will get a memory corruption. Additionally, this patch gets rid of group->query_id variable which is not used. Fixes: faec2f7b ('IB/sa: Track multicast join/leave requests') Signed-off-by:
-
Erez Shitrit authored
commit 546481c2 upstream. When a new CM connection is being requested, ipoib driver copies data from the path pointer in the CM/tx object, the path object might be invalid at the point and memory corruption will happened later when now the CM driver will try using that data. The next scenario demonstrates it: neigh_add_path --> ipoib_cm_create_tx --> queue_work (pointer to path is in the cm/tx struct) #while the work is still in the queue, #the port goes down and causes the ipoib_flush_paths: ipoib_flush_paths --> path_free --> kfree(path) #at this point the work scheduled starts. ipoib_cm_tx_start --> copy from the (invalid)path pointer: (memcpy(&pathrec, &p->path->pathrec, sizeof pathrec);) -> memory corruption. To fix that the driver now starts the CM/tx connection only if that specific path exists in the general paths database. This check is protected with the relevant locks, and uses the gid from the neigh member in the CM/tx object which is valid according to the ref count that was taken by the CM/tx. Fixes: 839fcaba ('IPoIB: Connected mode experimental support') Signed-off-by:
-
Emmanouil Maroudas authored
commit 993f88f1 upstream. Fix typo in edac_inc_ue_error() to increment ue_noinfo_count instead of ce_noinfo_count. Signed-off-by:
Emmanouil Maroudas <emmanouil.maroudas@gmail.com> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: linux-edac <linux-edac@vger.kernel.org> Fixes: 4275be63 ("edac: Change internal representation to work with layers") Link: http://lkml.kernel.org/r/1461425580-5898-1-git-send-email-emmanouil.maroudas@gmail.comSigned-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
Tejun Heo authored
commit 22b886dd upstream. Regardless of the previous CPU a timer was on, add_timer_on() currently simply sets timer->flags to the new CPU. As the caller must be seeing the timer as idle, this is locally fine, but the timer leaving the old base while unlocked can lead to race conditions as follows. Let's say timer was on cpu 0. cpu 0 cpu 1 ----------------------------------------------------------------------------- del_timer(timer) succeeds del_timer(timer) lock_timer_base(timer) locks cpu_0_base add_timer_on(timer, 1) spin_lock(&cpu_1_base->lock) timer->flags set to cpu_1_base operates on @timer operates on @timer This triggered with mod_delayed_work_on() which contains "if (del_timer()) add_timer_on()" sequence eventually leading to the following oops. BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffff810ca6e9>] detach_if_pending+0x69/0x1a0 ... Workqueue: wqthrash wqthrash_workfunc [wqthrash] task: ffff8800172ca680 ti: ffff8800172d0000 task.ti: ffff8800172d0000 RIP: 0010:[<ffffffff810ca6e9>] [<ffffffff810ca6e9>] detach_if_pending+0x69/0x1a0 ... Call Trace: [<ffffffff810cb0b4>] del_timer+0x44/0x60 [<ffffffff8106e836>] try_to_grab_pending+0xb6/0x160 [<ffffffff8106e913>] mod_delayed_work_on+0x33/0x80 [<ffffffffa0000081>] wqthrash_workfunc+0x61/0x90 [wqthrash] [<ffffffff8106dba8>] process_one_work+0x1e8/0x650 [<ffffffff8106e05e>] worker_thread+0x4e/0x450 [<ffffffff810746af>] kthread+0xef/0x110 [<ffffffff8185980f>] ret_from_fork+0x3f/0x70 Fix it by updating add_timer_on() to perform proper migration as __mod_timer() does. Mike: apply tglx backport Reported-and-tested-by:
Jeff Layton <jlayton@poochiereds.net> Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Chris Worley <chris.worley@primarydata.com> Cc: bfields@fieldses.org Cc: Michael Skralivetsky <michael.skralivetsky@primarydata.com> Cc: Trond Myklebust <trond.myklebust@primarydata.com> Cc: Shaohua Li <shli@fb.com> Cc: Jeff Layton <jlayton@poochiereds.net> Cc: kernel-team@fb.com Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20151029103113.2f893924@tlielax.poochiereds.net Link: http://lkml.kernel.org/r/20151104171533.GI5749@mtj.duckdns.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Mike Galbraith <mgalbraith@suse.de> Signed-off-by:
-
Gavin Li authored
commit add12505 upstream. This fixes the "BOGUS urb xfer" warning logged by usb_submit_urb(). Signed-off-by:
Gavin Li <git@thegavinli.com> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Krzysztof Kozlowski authored
commit f37fabb8 upstream. In the critical sysfs entry the thermal hwmon was returning wrong temperature to the user-space. It was reporting the temperature of the first trip point instead of the temperature of critical trip point. For example: /sys/class/hwmon/hwmon0/temp1_crit:50000 /sys/class/thermal/thermal_zone0/trip_point_0_temp:50000 /sys/class/thermal/thermal_zone0/trip_point_0_type:active /sys/class/thermal/thermal_zone0/trip_point_3_temp:120000 /sys/class/thermal/thermal_zone0/trip_point_3_type:critical Since commit e68b16ab ("thermal: add hwmon sysfs I/F") the driver have been registering a sysfs entry if get_crit_temp() callback was provided. However when accessed, it was calling get_trip_temp() instead of the get_crit_temp(). Fixes: e68b16ab ("thermal: add hwmon sysfs I/F") Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
Zhang Rui <rui.zhang@intel.com> [wt: s/thermal_hwmon.c/thermal_core.c in 3.10] Signed-off-by:
-
Linus Walleij authored
commit 307fe9dd upstream. All the scaling of the KXSD9 involves multiplication with a fraction number < 1. However the scaling value returned from IIO_INFO_SCALE was unpredictable as only the micros of the value was assigned, and not the integer part, resulting in scaling like this: $cat in_accel_scale -1057462640.011978 Fix this by assigning zero to the integer part. Tested-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Linus Walleij authored
commit 7ac61a06 upstream. Any readings from the raw interface of the KXSD9 driver will return an empty string, because it does not return IIO_VAL_INT but rather some random value from the accelerometer to the caller. Signed-off-by:
-
Cyrille Pitchen authored
commit 6f6ddbb0 upstream. In some cases a NACK interrupt may be pending in the Status Register (SR) as a result of a previous transfer. However at91_do_twi_transfer() did not read the SR to clear pending interruptions before starting a new transfer. Hence a NACK interrupt rose as soon as it was enabled again at the I2C controller level, resulting in a wrong sequence of operations and strange patterns of behaviour on the I2C bus, such as a clock stretch followed by a restart of the transfer. This first issue occurred with both DMA and PIO write transfers. Also when a NACK error was detected during a PIO write transfer, the interrupt handler used to wrongly start a new transfer by writing into the Transmit Holding Register (THR). Then the I2C slave was likely to reply with a second NACK. This second issue is fixed in atmel_twi_interrupt() by handling the TXRDY status bit only if both the TXCOMP and NACK status bits are cleared. Tested with a at24 eeprom on sama5d36ek board running a linux-4.1-at91 kernel image. Adapted to linux-next. Reported-by:
Peter Rosin <peda@lysator.liu.se> Signed-off-by:
Cyrille Pitchen <cyrille.pitchen@atmel.com> Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Tested-by:
Wolfram Sang <wsa@the-dreams.de> Fixes: 93563a6a ("i2c: at91: fix a race condition when using the DMA controller") Signed-off-by:
-
Vladimir Zapolskiy authored
commit 147b36d5 upstream. Race condition between registering an I2C device driver and deregistering an I2C adapter device which is assumed to manage that I2C device may lead to a NULL pointer dereference due to the uninitialized list head of driver clients. The root cause of the issue is that the I2C bus may know about the registered device driver and thus it is matched by bus_for_each_drv(), but the list of clients is not initialized and commonly it is NULL, because I2C device drivers define struct i2c_driver as static and clients field is expected to be initialized by I2C core: i2c_register_driver() i2c_del_adapter() driver_register() ... bus_add_driver() ... ... bus_for_each_drv(..., __process_removed_adapter) ... i2c_do_del_adapter() ... list_for_each_entry_safe(..., &driver->clients, ...) INIT_LIST_HEAD(&driver->clients); To solve the problem it is sufficient to do clients list head initialization before calling driver_register(). The problem was found while using an I2C device driver with a sluggish registration routine on a bus provided by a physically detachable I2C master controller, but practically the oops may be reproduced under the race between arbitraty I2C device driver registration and managing I2C bus device removal e.g. by unbinding the latter over sysfs: % echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind Unable to handle kernel NULL pointer dereference at virtual address 00000000 Internal error: Oops: 17 [#1] SMP ARM CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) task: e5ada400 task.stack: e4936000 PC is at i2c_do_del_adapter+0x20/0xcc LR is at __process_removed_adapter+0x14/0x1c Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 35bd004a DAC: 00000051 Process sh (pid: 533, stack limit = 0xe4936210) Stack: (0xe4937d28 to 0xe4938000) Backtrace: [<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c) [<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0) [<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284) [<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx]) [<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44) [<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c) [<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34) [<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104) [<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34) [<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54) [<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214) [<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120) [<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170) [<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8) [<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c) Signed-off-by:
Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by:
-
Dan Carpenter authored
commit e44c153b upstream. The code is checking for negative returns but it should be checking for zero. Fixes: aab3125c ('[media] em28xx: add support for registering multiple i2c buses') Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Yadi.hu authored
commit 371a0153 upstream. the eg20t driver call request_irq() function before the pch_base_address, base address of i2c controller's register, is assigned an effective value. there is one possible scenario that an interrupt which isn't inside eg20t arrives immediately after request_irq() is executed when i2c controller shares an interrupt number with others. since the interrupt handler pch_i2c_handler() has already active as shared action, it will be called and read its own register to determine if this interrupt is from itself. At that moment, since base address of i2c registers is not remapped in kernel space yet,so the INT handler will access an illegal address and then a error occurs. Signed-off-by:
Yadi.hu <yadi.hu@windriver.com> Signed-off-by:
-
