- 03 Mar, 2017 14 commits
-
-
Hannes Frederic Sowa authored
commit 11ffff75 upstream. In commit 1ec047eb ("ipv6: introduce per-interface counter for dad-completed ipv6 addresses") I build the detection of the first operational link-local address much to complex. Additionally this code now has a race condition. Replace it with a much simpler variant, which just scans the address list when duplicate address detection completes, to check if this is the first valid link local address and send RS and MLD reports then. Fixes: 1ec047eb ("ipv6: introduce per-interface counter for dad-completed ipv6 addresses") Reported-by:
Jiri Pirko <jiri@resnulli.us> Cc: Flavio Leitner <fbl@redhat.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by:
Flavio Leitner <fbl@redhat.com> Acked-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Daniel Borkmann authored
commit 965801e1 upstream. In function lowpan_header_create(), we invoke the following code construct: struct ipv6hdr *hdr; ... hdr = ipv6_hdr(skb); ... if (...) memcpy(hc06_ptr + 1, &hdr->flow_lbl[1], 2); else memcpy(hc06_ptr, &hdr, 4); Where the else path of the condition, that is, non-compression path, calls memcpy() with a pointer to struct ipv6hdr *hdr as source, thus two levels of indirection. This cannot be correct, and likely only one level of pointer was intended as source buffer for memcpy() here. Fixes: 44331fe2 ("IEEE802.15.4: 6LoWPAN basic support") Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com> Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Cc: Werner Almesberger <werner@almesberger.net> Signed-off-by:
-
Li RongQing authored
commit abb6013c upstream. when read/write the 64bit data, the correct lock should be hold. Fixes: 87b6d218 ("tunnel: implement 64 bits statistics") Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by:
Li RongQing <roy.qing.li@gmail.com> Signed-off-by:
-
Viresh Kumar authored
commit 08fd8c1c upstream. Prevent __cpufreq_add_dev() from overwriting the existing values of user_policy.{min|max|policy|governor} with defaults during resume from system suspend. Fixes: 5302c3fb ("cpufreq: Perform light-weight init/teardown during suspend/resume") Reported-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> [rjw: Changelog] Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit 72368d12 upstream. If cpufreq_policy_restore() returns NULL during system resume, __cpufreq_add_dev() should just fall back to the full initialization instead of returning an error, because that may actually make things work. Moreover, it should not leave stale fallback data behind after it has failed to restore a previously existing policy. This change is based on Viresh Kumar's work. Fixes: 5302c3fb ("cpufreq: Perform light-weight init/teardown during suspend/resume") Reported-by:
-
Viresh Kumar authored
commit 42f921a6 upstream. There are cases where cpufreq_add_dev() may fail for some CPUs during system resume. With the current code we will still have sysfs cpufreq files for those CPUs and struct cpufreq_policy would be already freed for them. Hence any operation on those sysfs files would result in kernel warnings. Example of problems resulting from resume errors (from Bjørn Mork): WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212() missing sysfs attribute operations for kobject: (null) Modules linked in: [stripped as irrelevant] CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153 Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011 0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006 ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000 ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310 Call Trace: [<ffffffff81380b0e>] dump_stack+0x55/0x76 [<ffffffff81038635>] warn_slowpath_common+0x7c/0x96 [<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212 [<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43 [<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82 [<ffffffff81182382>] ? sysfs_open_file+0x32/0x212 [<ffffffff811823c7>] sysfs_open_file+0x77/0x212 [<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac [<ffffffff81122562>] do_dentry_open+0x17c/0x257 [<ffffffff8112267e>] finish_open+0x41/0x4f [<ffffffff81130225>] do_last+0x80c/0x9ba [<ffffffff8112dbbd>] ? inode_permission+0x40/0x42 [<ffffffff81130606>] path_openat+0x233/0x4a1 [<ffffffff81130b7e>] do_filp_open+0x35/0x85 [<ffffffff8113b787>] ? __alloc_fd+0x172/0x184 [<ffffffff811232ea>] do_sys_open+0x6b/0xfa [<ffffffff811233a7>] SyS_openat+0xf/0x11 [<ffffffff8138c812>] system_call_fastpath+0x16/0x1b To fix this, remove those sysfs files or put the associated kobject in case of such errors. Also, to make it simple, remove the cpufreq sysfs links from all the CPUs (except for the policy->cpu) during suspend, as that operation won't result in a loss of sysfs file permissions and we can create those links during resume just fine. [js] no rwsem in 3.12 yet Fixes: 5302c3fb ("cpufreq: Perform light-weight init/teardown during suspend/resume") Reported-and-tested-by:
-
Bjørn Mork authored
commit 2167e239 upstream. This is effectively a revert of commit 5302c3fb ("cpufreq: Perform light-weight init/teardown during suspend/resume"), which enabled suspend/resume optimizations leaving the sysfs files in place. Errors during suspend/resume are not handled properly, leaving dead sysfs attributes in case of failures. There are are number of functions with special code for the "frozen" case, and all these need to also have special error handling. The problem is easy to demonstrate by making cpufreq_driver->init() or cpufreq_driver->get() fail during resume. The code is too complex for a simple fix, with split code paths in multiple blocks within a number of functions. It is therefore best to revert the patch enabling this code until the error handling is in place. Examples of problems resulting from resume errors: WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212() missing sysfs attribute operations for kobject: (null) Modules linked in: [stripped as irrelevant] CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153 Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011 0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006 ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000 ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310 Call Trace: [<ffffffff81380b0e>] dump_stack+0x55/0x76 [<ffffffff81038635>] warn_slowpath_common+0x7c/0x96 [<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212 [<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43 [<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82 [<ffffffff81182382>] ? sysfs_open_file+0x32/0x212 [<ffffffff811823c7>] sysfs_open_file+0x77/0x212 [<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac [<ffffffff81122562>] do_dentry_open+0x17c/0x257 [<ffffffff8112267e>] finish_open+0x41/0x4f [<ffffffff81130225>] do_last+0x80c/0x9ba [<ffffffff8112dbbd>] ? inode_permission+0x40/0x42 [<ffffffff81130606>] path_openat+0x233/0x4a1 [<ffffffff81130b7e>] do_filp_open+0x35/0x85 [<ffffffff8113b787>] ? __alloc_fd+0x172/0x184 [<ffffffff811232ea>] do_sys_open+0x6b/0xfa [<ffffffff811233a7>] SyS_openat+0xf/0x11 [<ffffffff8138c812>] system_call_fastpath+0x16/0x1b The failure to restore cpufreq devices on cancelled hibernation is not a new bug. It is caused by the ACPI _PPC call failing unless the hibernate is completed. This makes the acpi_cpufreq driver fail its init. Previously, the cpufreq device could be restored by offlining the cpu temporarily. And as a complete hibernation cycle would do this, it would be automatically restored most of the time. But after commit 5302c3fb the leftover sysfs attributes will block any device add action. Therefore offlining and onlining CPU 1 will no longer restore the cpufreq object, and a complete suspend/resume cycle will replace it with garbage. Fixes: 5302c3fb ("cpufreq: Perform light-weight init/teardown during suspend/resume") Signed-off-by:
-
Dan Carpenter authored
commit bdefc8cb upstream. We should be taking the minimum here instead of the max. It could lead to a buffer overflow. Fixes: 438d99e3 ('drm/nvd0/disp: initial crtc object implementation') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> a/drm/nv50_display.c b/drm/nv50_display.c index f8e66c08b11a..4e384a2f99c3 100644 Signed-off-by:
-
Dan Carpenter authored
commit cb4855b4 upstream. We fixed this to use free_netdev() instead of kfree() but unfortunately free_netdev() doesn't accept NULL pointers. Smatch complains about this, it's not something I discovered through testing. Fixes: 3030d40b ('staging: vt6655: use free_netdev instead of kfree') Fixes: 0a438d5b ('staging: vt6656: use free_netdev instead of kfree') Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Dan Carpenter authored
commit d6daef95 upstream. We assume that "pmic" could be NULL and then dereference it two lines later. I fix this by moving the dereference inside the NULL check. Fixes: c013f0a5 ('mfd: Add pm8xxx irq support') Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Dan Carpenter authored
commit 78032f9b upstream. We recently added a new error path and it needs a dev_put(). Fixes: 7adac1ec ('6lowpan: Only make 6lowpan links to IEEE802154 devices') Signed-off-by:
-
Ben Hutchings authored
commit 2b462638 upstream. If we failed to copy from the structure, writing back the flags leaks 31 bits of kernel memory (the rest of the ir_flags field). In any case, if we cannot copy from/to the structure, why should we expect putting just the flags to work? Also make sure ocfs2_info_handle_freeinode() returns the right error code if the copy_to_user() fails. Fixes: ddee5cdb ('Ocfs2: Add new OCFS2_IOC_INFO ioctl for ocfs2 v8.') Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Cc: Joel Becker <jlbec@evilplan.org> Acked-by:
Mark Fasheh <mfasheh@suse.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Theodore Ts'o authored
commit 2ba3e6e8 upstream. It is OK for s_first_meta_bg to be equal to the number of block group descriptor blocks. (It rarely happens, but it shouldn't cause any problems.) https://bugzilla.kernel.org/show_bug.cgi?id=194567 Fixes: 3a4b77cdSigned-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Eryu Guan authored
commit 3a4b77cd upstream. Ralf Spenneberg reported that he hit a kernel crash when mounting a modified ext4 image. And it turns out that kernel crashed when calculating fs overhead (ext4_calculate_overhead()), this is because the image has very large s_first_meta_bg (debug code shows it's 842150400), and ext4 overruns the memory in count_overhead() when setting bitmap buffer, which is PAGE_SIZE. ext4_calculate_overhead(): buf = get_zeroed_page(GFP_NOFS); <=== PAGE_SIZE buffer blks = count_overhead(sb, i, buf); count_overhead(): for (j = ext4_bg_num_gdb(sb, grp); j > 0; j--) { <=== j = 842150400 ext4_set_bit(EXT4_B2C(sbi, s++), buf); <=== buffer overrun count++; } This can be reproduced easily for me by this script: #!/bin/bash rm -f fs.img mkdir -p /mnt/ext4 fallocate -l 16M fs.img mke2fs -t ext4 -O bigalloc,meta_bg,^resize_inode -F fs.img debugfs -w -R "ssv first_meta_bg 842150400" fs.img mount -o loop fs.img /mnt/ext4 Fix it by validating s_first_meta_bg first at mount time, and refusing to mount if its value exceeds the largest possible meta_bg number. [js] use EXT4_HAS_INCOMPAT_FEATURE instead of new ext4_has_feature_meta_bg Reported-by:
Ralf Spenneberg <ralf@os-t.de> Signed-off-by:
Eryu Guan <guaneryu@gmail.com> Signed-off-by:
Andreas Dilger <adilger@dilger.ca> Signed-off-by:
-
- 01 Mar, 2017 26 commits
-
-
Dan Carpenter authored
commit d7cf0c34 upstream. At first glance it looks like there is a missing curly brace but actually the code works the same either way. I have adjusted the indenting but left the code the same. Signed-off-by:
-
Michael Schenk authored
commit 575ddce0 upstream. In the function rtl_usb_start we pre-allocate a certain number of urbs for RX path but they will not be freed when calling rtl_usb_stop. This results in leaking urbs when doing ifconfig up and down. Eventually, the system has no available urbs. Signed-off-by:
Michael Schenk <michael.schenk@albis-elcon.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Thomas Gleixner authored
commit 6cf18e69 upstream. This interrupt handler is broken in several ways: - It loops forever when the op code is not decodeable - It never returns IRQ_HANDLED because the only way to exit the loop returns IRQ_NONE unconditionally. The whole concept of this is broken. Creating devices in an interrupt handler is beyond any point of sanity. Make it at least behave halfways sane so accidental users do not have to deal with a hard to debug lockup. Fixes: e809c22b ("goldfish: add the goldfish virtual bus") Reported-by:
Gabriel C <nix.or.die@gmail.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Acked-by:
-
Thomas Gleixner authored
commit 47512cfd upstream. The goldfish platform code registers the platform device unconditionally which causes havoc in several ways if the goldfish_pdev_bus driver is enabled: - Access to the hardcoded physical memory region, which is either not available or contains stuff which is completely unrelated. - Prevents that the interrupt of the serial port can be requested - In case of a spurious interrupt it goes into a infinite loop in the interrupt handler of the pdev_bus driver (which needs to be fixed seperately). Add a 'goldfish' command line option to make the registration opt-in when the platform is compiled in. I'm seriously grumpy about this engineering trainwreck, which has seven SOBs from Intel developers for 50 lines of code. And none of them figured out that this is broken. Impressive fail! Fixes: ddd70cf9 ("goldfish: platform device for x86") Reported-by:
-
Johan Hovold authored
commit 9fef37d7 upstream. The current implementation failed to detect short transfers, something which could lead to bits of the uninitialised heap transfer buffer leaking to user space. Fixes: 149fc791 ("USB: ark3116: Setup some basic infrastructure for new ark3116 driver.") Fixes: f4c1e8d5 ("USB: ark3116: Make existing functions 16450-aware and add close and release functions.") Reviewed-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit 2eee0502 upstream. The opticon driver used a control request at open to trigger a CTS status notification to be sent over the bulk-in pipe. When the driver was converted to using the generic read implementation, an inverted test prevented this request from being sent, something which could lead to TIOCMGET reporting an incorrect CTS state. Reported-by:
-
Johan Hovold authored
commit 5ed8d410 upstream. Make sure to detect short control transfers and return zero on success when retrieving the modem status. This fixes the TIOCMGET implementation which since e1ed212d ("USB: spcp8x5: add proper modem-status support") has returned TIOCM_LE on successful retrieval, and avoids leaking bits from the stack on short transfers. This also fixes the carrier-detect implementation which since the above mentioned commit unconditionally has returned true. Fixes: e1ed212d ("USB: spcp8x5: add proper modem-status support") Reviewed-by:
-
Johan Hovold authored
commit a6bb1e17 upstream. FTDI devices use a receive latency timer to periodically empty the receive buffer and report modem and line status (also when the buffer is empty). When a break or error condition is detected the corresponding status flags will be set on a packet with nonzero data payload and the flags are not updated until the break is over or further characters are received. In order to avoid over-reporting break and error conditions, these flags must therefore only be processed for packets with payload. This specifically fixes the case where after an overrun, the error condition is continuously reported and NULL-characters inserted until further data is received. Reported-by:
Michael Walle <michael@walle.cc> Fixes: 72fda3ca ("USB: serial: ftd_sio: implement sysrq handling on break") Fixes: 166ceb69 ("USB: ftdi_sio: clean up line-status handling") Signed-off-by:
-
Johan Hovold authored
commit c6dce262 upstream. Since commit 557aaa7f ("ft232: support the ASYNC_LOW_LATENCY flag") the FTDI driver has been using a receive latency-timer value of 1 ms instead of the device default of 16 ms. The latency timer is used to periodically empty a non-full receive buffer, but a status header is always sent when the timer expires including when the buffer is empty. This means that a two-byte bulk message is received every millisecond also for an otherwise idle port as long as it is open. Let's restore the pre-2009 behaviour which reduces the rate of the status messages to 1/16th (e.g. interrupt frequency drops from 1 kHz to 62.5 Hz) by not setting ASYNC_LOW_LATENCY by default. Anyone willing to pay the price for the minimum-latency behaviour should set the flag explicitly instead using the TIOCSSERIAL ioctl or a tool such as setserial (e.g. setserial /dev/ttyUSB0 low_latency). Note that since commit 0cbd81a9 ("USB: ftdi_sio: remove tty->low_latency") the ASYNC_LOW_LATENCY flag has no other effects but to set a minimal latency timer. Reported-by:
Antoine Aubert <a.aubert@overkiz.com> Fixes: 557aaa7f ("ft232: support the ASYNC_LOW_LATENCY flag") Signed-off-by:
-
Johan Hovold authored
commit 427c3a95 upstream. Make sure to detect short responses when fetching the modem status in order to avoid parsing uninitialised buffer data and having bits of it leak to user space. Note that we still allow for short 1-byte responses. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Reviewed-by:
-
Ken Lin authored
commit 9a593656 upstream. Add new USB IDs for cp2104/5 devices on Bx50v3 boards due to the design change. Signed-off-by:
Ken Lin <yungching0725@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit 5182c2cf upstream. Fix another NULL-pointer dereference at open should a malicious device lack an interrupt-in endpoint. Note that the driver has a broken check for an interrupt-in endpoint which means that an interrupt URB has never even been submitted. Fixes: 3f542974 ("USB: Moschip 7840 USB-Serial Driver") Reviewed-by:
-
Javier Martinez Canillas authored
commit abe81f3b upstream. If the driver is built as a module, autoload won't work because the module alias information is not filled. So user-space can't match the registered device with the corresponding module. Export the module alias information using the MODULE_DEVICE_TABLE() macro. Before this patch: $ modinfo drivers/tty/serial/msm_serial.ko | grep alias $ After this patch: $ modinfo drivers/tty/serial/msm_serial.ko | grep alias alias: of:N*T*Cqcom,msm-uartdmC* alias: of:N*T*Cqcom,msm-uartdm alias: of:N*T*Cqcom,msm-uartC* alias: of:N*T*Cqcom,msm-uart Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Acked-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Maxime Jayat authored
[ Upstream commit e623a9e9 ] Commit 34b88a68 ("net: Fix use after free in the recvmmsg exit path"), changed the exit path of recvmmsg to always return the datagrams variable and modified the error paths to set the variable to the error code returned by recvmsg if necessary. However in the case sock_error returned an error, the error code was then ignored, and recvmmsg returned 0. Change the error path of recvmmsg to correctly return the error code of sock_error. The bug was triggered by using recvmmsg on a CAN interface which was not up. Linux 4.6 and later return 0 in this case while earlier releases returned -ENETDOWN. Fixes: 34b88a68 ("net: Fix use after free in the recvmmsg exit path") Signed-off-by:
Maxime Jayat <maxime.jayat@mobile-devices.fr> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 4c03b862 ] A nested lock depth was added to the hasbin_delete() code but it doesn't actually work some well and results in tons of lockdep splats. Fix the code instead to properly drop the lock around the operation and just keep peeking the head of the hashbin queue. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Tested-by:
-
Andrey Konovalov authored
[ Upstream commit 5edabca9 ] In the current DCCP implementation an skb for a DCCP_PKT_REQUEST packet is forcibly freed via __kfree_skb in dccp_rcv_state_process if dccp_v6_conn_request successfully returns. However, if IPV6_RECVPKTINFO is set on a socket, the address of the skb is saved to ireq->pktopts and the ref count for skb is incremented in dccp_v6_conn_request, so skb is still in use. Nevertheless, it gets freed in dccp_rcv_state_process. Fix by calling consume_skb instead of doing goto discard and therefore calling __kfree_skb. Similar fixes for TCP: fb7e2399 [TCP]: skb is unexpectedly freed. 0aea76d3 tcp: SYN packets are now simply consumed Signed-off-by:
Andrey Konovalov <andreyknvl@google.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Anoob Soman authored
[ Upstream commit 2bd624b4 ] Commit 66644982 ("packet: call fanout_release, while UNREGISTERING a netdev"), unfortunately, introduced the following issues. 1. calling mutex_lock(&fanout_mutex) (fanout_release()) from inside rcu_read-side critical section. rcu_read_lock disables preemption, most often, which prohibits calling sleeping functions. [ ] include/linux/rcupdate.h:560 Illegal context switch in RCU read-side critical section! [ ] [ ] rcu_scheduler_active = 1, debug_locks = 0 [ ] 4 locks held by ovs-vswitchd/1969: [ ] #0: (cb_lock){++++++}, at: [<ffffffff8158a6c9>] genl_rcv+0x19/0x40 [ ] #1: (ovs_mutex){+.+.+.}, at: [<ffffffffa04878ca>] ovs_vport_cmd_del+0x4a/0x100 [openvswitch] [ ] #2: (rtnl_mutex){+.+.+.}, at: [<ffffffff81564157>] rtnl_lock+0x17/0x20 [ ] #3: (rcu_read_lock){......}, at: [<ffffffff81614165>] packet_notifier+0x5/0x3f0 [ ] [ ] Call Trace: [ ] [<ffffffff813770c1>] dump_stack+0x85/0xc4 [ ] [<ffffffff810c9077>] lockdep_rcu_suspicious+0x107/0x110 [ ] [<ffffffff810a2da7>] ___might_sleep+0x57/0x210 [ ] [<ffffffff810a2fd0>] __might_sleep+0x70/0x90 [ ] [<ffffffff8162e80c>] mutex_lock_nested+0x3c/0x3a0 [ ] [<ffffffff810de93f>] ? vprintk_default+0x1f/0x30 [ ] [<ffffffff81186e88>] ? printk+0x4d/0x4f [ ] [<ffffffff816106dd>] fanout_release+0x1d/0xe0 [ ] [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0 2. calling mutex_lock(&fanout_mutex) inside spin_lock(&po->bind_lock). "sleeping function called from invalid context" [ ] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620 [ ] in_atomic(): 1, irqs_disabled(): 0, pid: 1969, name: ovs-vswitchd [ ] INFO: lockdep is turned off. [ ] Call Trace: [ ] [<ffffffff813770c1>] dump_stack+0x85/0xc4 [ ] [<ffffffff810a2f52>] ___might_sleep+0x202/0x210 [ ] [<ffffffff810a2fd0>] __might_sleep+0x70/0x90 [ ] [<ffffffff8162e80c>] mutex_lock_nested+0x3c/0x3a0 [ ] [<ffffffff816106dd>] fanout_release+0x1d/0xe0 [ ] [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0 3. calling dev_remove_pack(&fanout->prot_hook), from inside spin_lock(&po->bind_lock) or rcu_read-side critical-section. dev_remove_pack() -> synchronize_net(), which might sleep. [ ] BUG: scheduling while atomic: ovs-vswitchd/1969/0x00000002 [ ] INFO: lockdep is turned off. [ ] Call Trace: [ ] [<ffffffff813770c1>] dump_stack+0x85/0xc4 [ ] [<ffffffff81186274>] __schedule_bug+0x64/0x73 [ ] [<ffffffff8162b8cb>] __schedule+0x6b/0xd10 [ ] [<ffffffff8162c5db>] schedule+0x6b/0x80 [ ] [<ffffffff81630b1d>] schedule_timeout+0x38d/0x410 [ ] [<ffffffff810ea3fd>] synchronize_sched_expedited+0x53d/0x810 [ ] [<ffffffff810ea6de>] synchronize_rcu_expedited+0xe/0x10 [ ] [<ffffffff8154eab5>] synchronize_net+0x35/0x50 [ ] [<ffffffff8154eae3>] dev_remove_pack+0x13/0x20 [ ] [<ffffffff8161077e>] fanout_release+0xbe/0xe0 [ ] [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0 4. fanout_release() races with calls from different CPU. To fix the above problems, remove the call to fanout_release() under rcu_read_lock(). Instead, call __dev_remove_pack(&fanout->prot_hook) and netdev_run_todo will be happy that &dev->ptype_specific list is empty. In order to achieve this, I moved dev_{add,remove}_pack() out of fanout_{add,release} to __fanout_{link,unlink}. So, call to {,__}unregister_prot_hook() will make sure fanout->prot_hook is removed as well. [js] no rollover in 3.12 Fixes: 66644982 ("packet: call fanout_release, while UNREGISTERING a netdev") Reported-by:
Anoob Soman <anoob.soman@citrix.com> Acked-by:
-
Eric Dumazet authored
[ Upstream commit d199fab6 ] Multiple threads can call fanout_add() at the same time. We need to grab fanout_mutex earlier to avoid races that could lead to one thread freeing po->rollover that was set by another thread. Do the same in fanout_release(), for peace of mind, and to help us finding lockdep issues earlier. [js] no rollover in 3.12 Fixes: dc99f600 ("packet: Add fanout support.") Fixes: 0648ab70 ("packet: rollover prepare: per-socket state") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 8b74d439 ] It seems nobody used LLC since linux-3.12. Fortunately fuzzers like syzkaller still know how to run this code, otherwise it would be no fun. Setting skb->sk without skb->destructor leads to all kinds of bugs, we now prefer to be very strict about it. Ideally here we would use skb_set_owner() but this helper does not exist yet, only CAN seems to have a private helper for that. [js] take sock_efree from 62bccb8c Fixes: 376c7311 ("net: add a temporary sanity check in skb_orphan()") Signed-off-by:
-
Colin Ian King authored
commit 2b2f5ff0 upstream. This patch fixes a RTC wakealarm issue, namely, the event fires during hibernate and is not cleared from the list, causing hwclock to block. The current enqueuing does not trigger an alarm if any expired timers already exist on the timerqueue. This can occur when a RTC wake alarm is used to wake a machine out of hibernate and the resumed state has old expired timers that have not been removed from the timer queue. This fix skips over any expired timers and triggers an alarm if there are no pending timers on the timerqueue. Note that the skipped expired timer will get reaped later on, so there is no need to clean it up immediately. The issue can be reproduced by putting a machine into hibernate and waking it with the RTC wakealarm. Running the example RTC test program from tools/testing/selftests/timers/rtctest.c after the hibernate will block indefinitely. With the fix, it no longer blocks after the hibernate resume. BugLink: http://bugs.launchpad.net/bugs/1333569Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by:
-
Sergey Senozhatsky authored
commit fc98c3c8 upstream. Use rcuidle console tracepoint because, apparently, it may be issued from an idle CPU: hw-breakpoint: Failed to enable monitor mode on CPU 0. hw-breakpoint: CPU 0 failed to disable vector catch =============================== [ ERR: suspicious RCU usage. ] 4.10.0-rc8-next-20170215+ #119 Not tainted ------------------------------- ./include/trace/events/printk.h:32 suspicious rcu_dereference_check() usage! other info that might help us debug this: RCU used illegally from idle CPU! rcu_scheduler_active = 2, debug_locks = 0 RCU used illegally from extended quiescent state! 2 locks held by swapper/0/0: #0: (cpu_pm_notifier_lock){......}, at: [<c0237e2c>] cpu_pm_exit+0x10/0x54 #1: (console_lock){+.+.+.}, at: [<c01ab350>] vprintk_emit+0x264/0x474 stack backtrace: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-rc8-next-20170215+ #119 Hardware name: Generic OMAP4 (Flattened Device Tree) console_unlock vprintk_emit vprintk_default printk reset_ctrl_regs dbg_cpu_pm_notify notifier_call_chain cpu_pm_exit omap_enter_idle_coupled cpuidle_enter_state cpuidle_enter_state_coupled do_idle cpu_startup_entry start_kernel This RCU warning, however, is suppressed by lockdep_off() in printk(). lockdep_off() increments the ->lockdep_recursion counter and thus disables RCU_LOCKDEP_WARN() and debug_lockdep_rcu_enabled(), which want lockdep to be enabled "current->lockdep_recursion == 0". Link: http://lkml.kernel.org/r/20170217015932.11898-1-sergey.senozhatsky@gmail.comSigned-off-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reported-by:
Tony Lindgren <tony@atomide.com> Tested-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Lindgren <tony@atomide.com> Cc: Russell King <rmk@armlinux.org.uk> Signed-off-by:
-
Yang Yang authored
commit 25f71d1c upstream. The UEVENT user mode helper is enabled before the initcalls are executed and is available when the root filesystem has been mounted. The user mode helper is triggered by device init calls and the executable might use the futex syscall. futex_init() is marked __initcall which maps to device_initcall, but there is no guarantee that futex_init() is invoked _before_ the first device init call which triggers the UEVENT user mode helper. If the user mode helper uses the futex syscall before futex_init() then the syscall crashes with a NULL pointer dereference because the futex subsystem has not been initialized yet. Move futex_init() to core_initcall so futexes are initialized before the root filesystem is mounted and the usermode helper becomes available. [ tglx: Rewrote changelog ] Signed-off-by:
Yang Yang <yang.yang29@zte.com.cn> Cc: jiang.biao2@zte.com.cn Cc: jiang.zhengxiong@zte.com.cn Cc: zhong.weidong@zte.com.cn Cc: deng.huali@zte.com.cn Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1483085875-6130-1-git-send-email-yang.yang29@zte.com.cnSigned-off-by:
-
Johannes Thumshirn authored
commit fd3fc0b4 upstream. Don't crash the machine just because of an empty transfer. Use WARN_ON() combined with returning an error. Found by Dmitry Vyukov and syzkaller. [ Changed to "WARN_ON_ONCE()". Al has a patch that should fix the root cause, but a BUG_ON() is not acceptable in any case, and a WARN_ON() might still be a cause of excessive log spamming. NOTE! If this warning ever triggers, we may end up leaking resources, since this doesn't bother to try to clean the command up. So this WARN_ON_ONCE() triggering does imply real problems. But BUG_ON() is much worse. People really need to stop using BUG_ON() for "this shouldn't ever happen". It makes pretty much any bug worse. - Linus ] Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Reported-by:
-
Mauro Carvalho Chehab authored
commit f9c85ee6 upstream. Reported as a Kaffeine bug: https://bugs.kde.org/show_bug.cgi?id=375811 The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. On Kernel 4.9, the default is to not accept DMA on stack anymore on x86 architecture. On other architectures, this has been a requirement since Kernel 2.2. So, after this patch, this driver should likely work fine on all archs. Tested with USB ID 2040:5510: Hauppauge Windham Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Miklos Szeredi authored
commit 5a81e6a1 upstream. Flags (PIPE_BUF_FLAG_PACKET, PIPE_BUF_FLAG_GIFT) could remain on the unused part of the pipe ring buffer. Previously splice_to_pipe() left the flags value alone, which could result in incorrect behavior. Uninitialized flags appears to have been there from the introduction of the splice syscall. Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Christoph Hellwig authored
commit 635d98b1 upstream. scsi_init_io should only be called for requests that transfer data, so move the assert that a request has segments from the callers into scsi_init_io. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
